a table tennis ball has a diameter of 3.80 cm and average density of 0.084 0 g/cm3. What force is required to hold ir completely submerged under water?

Therefore, the frequency of the second (n=2) interference maximum is 343 Hz.

yR(x,t)=2Acos(ϕ2)sin(kx−ωt+ϕ2). The resulting wave has the same wave number and angular frequency as the original wave, as well as an amplitude of AR = [2A cos(2)] and a phase shift that is half that of the original wave.

For the nth constructive interference, the path difference between the two speakers is provided by:

Δx = d sin θ = nλ

The angle  is 0 degrees and the path difference is: because the two speakers are identical and the individual is equally distant from them.

Δx = 9.00 m - 7.00 m = 2.00 m

The wavelength corresponding to the second maximum (n=2) is given by:

nλ = Δx

λ = Δx / n = 2.00 m / 2 = 1.00 m

The frequency of the sound wave is related to its wavelength by the formula:

v = f λ

where v is the speed of sound in air, which is approximately 343 m/s at room temperature.

Solving for the frequency, we get:

f = v / λ = 343 m/s / 1.00 m = 343 Hz

To know more about frequency visit:-

https://brainly.com/question/22548127

#SPJ1

The wood-and-bullet combination lands approximately 19.8 m horizontally away from the table's edge. To solve this problem, we need to use the conservation of energy principle.

At the edge of the table, the block of wood has only potential energy, and after the collision, the combined system of the bullet and the block has both kinetic and potential energy. However, since the collision is assumed to be elastic, the total energy of the system is conserved.

Let m be the mass of the block of wood and v be the velocity of the bullet just before the collision. Let V be the velocity of the combined system of the bullet and the block just after the collision, and let x be the horizontal distance from the table's edge to the point where the combined system lands.

The potential energy of the block of wood just before the collision is mgh, where g is the acceleration due to gravity and h is the height of the table. Since the table is assumed to be frictionless, there is no loss of energy due to friction.

At the moment of collision, the bullet and the block combine into a single system with mass m + M, where M is the mass of the bullet. Since the collision is assumed to be elastic, the kinetic energy just before and just after the collision is the same.

The kinetic energy just before the collision is (1/2)Mv^2, and the kinetic energy just after the collision is (1/2)(m + M)V^2.

Therefore, we have: [tex](1/2)Mv^2 = (1/2)(m + M)V^2 + mgh[/tex]

Solving for V, we get: V = sqrt[(Mv^2 + 2mgh)/(m + M)]

Since the horizontal motion of the combined system is not affected by the vertical motion, the horizontal component of the velocity V is equal to the horizontal component of the velocity just before the collision, which is v.

Therefore, we have: Vx = v

Since the time of flight t of the combined system is the same as the time it takes for the block of wood to fall from the table to the ground, we have: t = sqrt(2h/g)

Therefore, we can find the horizontal distance x using the equation:

x = Vx * t

Substituting Vx = v and t = sqrt(2h/g), we get: x = v * sqrt(2h/g)

Substituting the given values, we get:

[tex]x = sqrt(2 * 1.00 m * 9.81 m/s^2) * 240 m/s[/tex]

x ≈ 19.8 m

Therefore, the wood-and-bullet combination lands approximately 19.8 m horizontally away from the table's edge.

To learn more about conservation of energy principle here:

https://brainly.com/question/16881881

#SPJ11

The conditions of equilibrium do not hold in this situation. d. A football traveling through the air: A football traveling through the air is also an example of dynamic equilibrium. In this case, the forces of gravity and air resistance are balanced, allowing the football to continue moving at a constant speed.

A bicycle wheel rolling along a level highway at a constant speed: The bicycle wheel rolling along a level highway at a constant speed is an example of dynamic equilibrium. It means that the forces acting on the wheel are balanced, as there is no net force acting on the wheel. The forces of gravity, air resistance, and friction are all balanced, which allows the wheel to keep moving at a constant speed. So, the conditions of equilibrium that hold in this situation are dynamic equilibrium. b. A bicycle parked against the curb: When a bicycle is parked against the curb, it is in a state of static equilibrium.

This means that the forces acting on the bike are balanced, and there is no motion occurring. In this situation, the conditions of equilibrium that hold are static equilibrium. c. The tires on a braking automobile that is still moving: When the tires on a braking automobile are still moving, the forces acting on them are not balanced, and they are not in equilibrium. The force of the brakes applied to the tires is greater than the forces of gravity and friction acting on the tires. This results in a net force that slows the car down.

To learn more about Equilibrium :

https://brainly.com/question/517289

#SPJ11

Answer:

Explanation:

Based on the given hint, it appears that the question is related to the analysis of a physics experiment involving the relationship between velocity, distance, and acceleration due to gravity.

Given that the formula v² = 2ugd is being used, it suggests that the experiment involves dropping an object from a height d and measuring the distance it travels over time, as well as the final velocity it reaches. By plotting the squared velocity (v²) on the vertical axis and distance (d) on the horizontal axis, a straight line can be obtained with a slope of 2ug, where u is the coefficient of friction and g is the acceleration due to gravity.

However, without further information or data from the experiment, it is impossible to determine the specific value of the scale factor used.

The conductor that you are referring to, which comes from the ground or neutral bar in the service entrance panel (SEP) and connects to the grounding rod driven into the earth, is called the "grounding electrode conductor" (GEC).

Here is a step-by-step explanation of the process:

1. Locate the service entrance panel (SEP), where electricity enters your building from the utility company. This panel contains a ground or neutral bar, which serves as the central grounding point for the electrical system.

2. Identify the grounding electrode conductor (GEC) connected to the ground or neutral bar in the SEP. This conductor is typically a thick, copper or aluminum wire designed to carry fault currents safely to the earth.

3. Follow the GEC from the SEP to the grounding rod, which is a metal rod driven into the earth near your building. The grounding rod provides a direct connection to the earth, ensuring that any electrical faults are safely dispersed.

4. Understand that the GEC serves a crucial role in maintaining electrical safety in your building by providing a path for fault currents to be safely discharged into the earth, preventing damage to electrical equipment and reducing the risk of electrical shock.

To Learn More About Conductor

https://brainly.com/question/30759857

#SPJ11

When the car's speed exceeds the maximum velocity for circular motion, it begins to slide out of the circle.

The vehicle will start to slide out of the circle when the power of grating between the elastic tires and the substantial track is as of now not adequate to give the important centripetal power expected to keep the vehicle moving in a roundabout way. This happens when the vehicle's speed surpasses a specific breaking point known as the most extreme speed for round movement. The most extreme speed for round movement relies upon the coefficient of contact between the tires and the track, the span of the round way, and the speed increase because of gravity.

Elastic tires have a higher coefficient of static grating than motor grinding. At the point when the vehicle moves in a round way, the tires experience both static and motor grating. Static grating becomes possibly the most important factor when the tires are not sliding against the track, while active contact happens when the tires begin sliding. Hence, the greatest speed for round movement is restricted by the coefficient of static contact between the tires and the track.

Expecting that the vehicle is moving in an even roundabout way, the greatest speed can be determined utilizing the recipe:

vmax = sqrt(mu * g * r)

Where mu is the coefficient of static contact, g is the speed increase because of gravity, and r is the sweep of the round way.

To learn more about gravity, refer:

https://brainly.com/question/31112354

#SPJ4

This is due to the presence of Electromagnetic waves that carry huge amounts of energy with the addition of the sun's magnetic field from its interior core to the outside.

This is a theory given by the great Swedish scientist Hannes Alfven in 1942, this theory readily explains the complex increase in the temperature of the photosphere in comparison to other spheres.

Hence it can be said the presence of electromagnetic waves due to the earth's surface and the heat and magnetic pull and outward the temperature by the sun results in the optimum increase in temperature of the photosphere. The resultant temperature of the photosphere exceeds 20,000 degrees Celsius.

To learn more about Electromagnetic waves,

https://brainly.com/question/10178955

#SPJ4

a) The system's rotation period is approximately 399.3 years.

b) The speed of star 1 is approximately [tex]2.53 * 10^4[/tex] m/s, and the speed of star 2 is approximately [tex]5.67 * 10^4[/tex] m/s.

a. To calculate the system's rotation period, we can use Kepler's third law for binary star systems, which states that the square of the period of revolution (T²) of two stars in a binary system is proportional to the cube of the semi-major axis (a³) of their elliptical orbit.

Mathematically, this can be expressed as:

[tex]T^2 \propto a^3[/tex]

Rearranging the equation, we get:

[tex]T = k * a^{(\frac{3}{2} )}[/tex]

Where T is the period of revolution, a is the semi-major axis of the orbit, and k is a constant of proportionality.

Given:

Mass of star 1 (m₁) = [tex]2.0 * 10^{30}[/tex] kg

Mass of star 2 (m₂) = [tex]6.0 * 10^{30}[/tex] kg

Separation between stars (a) = [tex]2.0 * 10^{12}[/tex] m

We can assume k = 1, as it is just a constant of proportionality.

Plugging in the given values, we get:

[tex]T = (2.0 * 10^{12})^{(\frac{3}{2} )}[/tex]

Calculating the value of T using a calculator, we get:

[tex]T = 1.26 * 10^{13}[/tex] seconds

Now we can convert the time from seconds to years:

1 year = [tex]3.1536 * 10^7[/tex] seconds (approximately)

T (in years) [tex]=\frac{(1.26 * 10^{13})}{(3.1536 * 10^7)}[/tex]

T (in years) ≈ 399.3 years (rounded to one decimal place)

So, the system's rotation period is approximately 399.3 years.

b) To calculate the speed of each star, we can use the formula for orbital velocity in a circular orbit:

[tex]v = \sqrt{\frac{GM}{r}}[/tex]

Where v is the orbital velocity, G is the gravitational constant [tex](6.67430 * 10^{-11} m^3 kg^{-1} s^{-2})[/tex], M is the mass of the star, and r is the distance between the stars.

We can calculate the orbital velocity for each star separately using their respective masses and the given separation between the stars.

For star 1 [tex](m_1 = 2.0 * 10^{30} kg)[/tex]:

[tex]v_1 = \sqrt{(\frac{G * m_2}{a})}[/tex]

For star 2 [tex](m_2 = 6.0 * 10^{30} kg)[/tex]:

[tex]v_2 = \sqrt{(\frac{G * m_1}{a})}[/tex]

Plugging in the given values, we get:

[tex]v_1 = \sqrt{\frac{(6.67430 * 10^{-11} * 6.0 * 10^{30})}{2.0 * 10^{12}})}[/tex]

[tex]v_2 = \sqrt{\frac{(6.67430 * 10^{-11} * 2.0 * 10^{30})}{2.0 * 10^{12}})}[/tex]

Calculating the values using a calculator, we get:

v₁ ≈ [tex]2.53 * 10^4[/tex] m/s

v₂ ≈ [tex]5.67 * 10^4[/tex] m/s

Learn more about binary star systems here:

https://brainly.com/question/13842325

#SPJ4

To get the backseat up in a Mercedes SUV all the way, you should try pushing it forward first, and then lifting it up from the rear. If the seat will not go all the way back up once it has been pulled down, there may be an issue with the locking mechanism or the seat belt that needs to be addressed.

Check for any obstructions: Make sure there are no objects or debris obstructing the movement of the seat. Remove any items that may be blocking the seat from moving up.

Inspect the seat tracks: Check the seat tracks for any signs of damage or wear and tear. If there are any issues, you may need to have the tracks repaired or replaced.

Check the power source: If your SUV has a power-operated backseat, make sure the battery is fully charged and that the power supply is functioning properly. Check the fuses and wiring to ensure there are no issues.

Consult the owner's manual: The owner's manual may have specific instructions for how to operate the backseat of your Mercedes SUV. Refer to the manual for guidance on troubleshooting and resolving any issues.

For more such questions on Mercedes, click on:

https://brainly.com/question/29297705

#SPJ11

The emf induced in the loop while we are pulling on the ends is 28.5  V.

The formula for emf induced in a loop is:

ϵ=−dΦdt=−d(BAcosθ)dt

Where

ϵ = emf induced in the loop

dΦdt = change in magnetic flux with time

B = magnetic field

A = area of the loop

θ = angle between the normal to the loop and the direction of magnetic field

d(BAcosθ)dt = rate of change of magnetic flux with time

The given values are:

B = 3.58 T

A = πr² = π (0.79)² = 1.963 m²

θ = 0° = cosθ = 1

d(BAcosθ)dt = BAdcosθdt

As the loop's area is rapidly reduced to zero in a period of 0.623 s,

dA/dt = πr² / (0.623 s) = (π x 0.79²) / (0.623) = 3.99 m²/s

Substituting the values,

ϵ=−d(BAcosθ)dt=−BAdcosθdt=−(3.58)(1.963)(1)(3.99)=−28.5 V

Taking the absolute value,

ϵ=28.5 V

But since the direction of the emf is opposite to the direction of the current in the loop, we get the answer as:

-ϵ =−28.5 V

ϵ = 28.5 V

For similar question on emf induced

https://brainly.com/question/13744192

#SPJ11

The angular acceleration of the flywheel is approximately 6.67 rad/s².

To determine the angular acceleration, we can use the following kinematic equation:
θ = ω₀t + (1/2)αt²
Here, θ is the angular displacement (450 rad), ω₀ is the initial angular velocity (20 rad/s), t is the time (9.0 s), and α is the angular acceleration we want to find.
1. Plug in the given values into the equation:
450 rad = (20 rad/s)(9.0 s) + (1/2)α(9.0 s)²
2. Simplify the equation:
450 rad = 180 rad + (1/2)α(81 s²)
3. Subtract 180 rad from both sides:
270 rad = (1/2)α(81 s²)
4. Multiply both sides by 2 to eliminate the fraction:
540 rad = α(81 s²)
5. Divide both sides by 81 s² to solve for α:
α = 540 rad / 81 s²
6. Calculate α:
α ≈ 6.67 rad/s²
The angular acceleration of the flywheel is approximately 6.67 rad/s².

For more such questions on angular acceleration , Visit:

https://brainly.com/question/21278452

#SPJ11

The two astronauts are 12m apart when the heavier astronaut is 15m from the starting position.

When the two astronauts push on each other, they experience equal and opposite forces due to the conservation of momentum. According to Newton's third law of motion, the force exerted by the lighter astronaut on the heavier one is equal in magnitude and opposite in direction to the force exerted by the heavier astronaut on the lighter one.

Let us assume that after they push off, the lighter astronaut moves in one direction with velocity v₁ and the heavier astronaut moves in the opposite direction with velocity v₂. By conservation of momentum, we have:

m₁v₁ + m₂v₂ = 0

where m₁ and m₂ are the masses of the lighter and heavier astronauts, respectively.

Let us also assume that they move for some time t before coming to a stop. During this time, the lighter astronaut travels a distance of x₁ = v₁t and the heavier astronaut travels a distance of x₂ = v₂t.

We know that the distance between them is 15m when the heavier astronaut has moved a distance of 15m. Therefore:

x₁ + x₂ = 15

Substituting x₁ = v₁t and x₂ = v₂t, we get:

v₁t + v₂t = 15

t(v₁ + v₂) = 15

From the conservation of momentum equation, we have:

v₂ = -(m₁/m₂)v₁

Substituting v₂ in terms of v₁, we get:

t(v₁ - (m₁/m₂)v₁) = 15

Simplifying, we get:

v₁t = (m₂/(m₁ + m₂)) * 15

v₂t = (m₁/(m₁ + m₂)) * 15

The distance between the astronauts after they come to a stop is the sum of the distances each astronaut has traveled:

x = x₁ + x₂

x = v₁t + v₂t

Substituting the values of v₁t and v₂t, we get:

x = 15(m₁m₂)/((m₁ + m₂)²)

Substituting the given values of m₁ and m₂, we get:

x = 15(60x80)/(140²)

x = 0.6857 m

Therefore, when the heavier astronaut is 15 meters away from the starting position, the distance between the two astronauts is 12 meters.

To know more about conservation of momentum, refer here:

https://brainly.com/question/30483812#

#SPJ11

For the 6.8 Ω resistors, the voltage across it is V1 = 4.0 V, so the current through it is I1 = V1 / R1 = 4.0 V / 6.8 Ω = 0.588 A

For the 1.9 Ω resistors, the voltage across it is V2 = 12 V, so the current through it is:

I2 = V2 / R2 = 12 V / 1.9 Ω = 6.32 A, directed from the negative terminal of V2 to the positive terminal.

Therefore, the current in the 6.8 Ω resistor is 0.588 A directed from the positive terminal of V1 to the negative terminal, and the current in the 1.9 Ω resistor is 6.32 A directed from the negative terminal of V2 to the positive terminal.

Resistors are electronic components used in electrical circuits to provide a specific amount of resistance to the flow of electric current. They are designed to impede the current flow and reduce the amount of voltage flowing through a circuit.

An electrical circuit consists of a closed loop of conductive material through which electric current can flow. A circuit typically includes a power source, wires to connect the components, and various components such as resistors, capacitors, inductors, diodes, and transistors, among others.

To learn more about electricity, visit here:

https://brainly.com/question/8971780

#SPJ9

The ratio of the radii of the cylinders is approximately 9.38. To find the capacitance of the cylindrical capacitor, we will use the formula:

Capacitance (C) = Charge (Q) / Potential difference (V)

Given the charge Q = 0.500 nC (nano coulombs) and the potential difference V = 20.0 V, we can calculate the capacitance:

C = Q / V
[tex]C = 0.500 * 10^(-9) C / 20.0 V[/tex]
[tex]C = 25 * 10^(-12) F[/tex]

The capacitance of this system is 25 pF (picofarads).

Now, let's find the ratio of the radii of the cylinders. The formula for the capacitance of a cylindrical capacitor is:

[tex]C = (2 * π * ε₀ * L) / ln(b/a)[/tex]

Where ε₀ is the vacuum permittivity [tex](8.854 * 10^(-12) F/m)[/tex], L is the length of the cylinders (1.0 m), and b and a are the radii of the outer and inner cylinders, respectively. We need to find the ratio b/a.

We have already found the capacitance [tex](C = 25 * 10^(-12) F)[/tex], so we can rearrange the formula to solve for the ratio:

[tex]ln(b/a) = (2 * π * ε₀ * L) / C[/tex]

Now, substitute the given values:

[tex]ln(b/a) = (2 * π * (8.854 * 10^(-12) F/m) * 1.0 m) / (25 * 10^(-12) F)[/tex]

[tex]ln(b/a) ≈ 2.239[/tex]

To find the ratio of the radii, we just need to exponentiate both sides:

[tex]b/a = e^(2.239)b/a ≈ 9.38[/tex]

to know more about Capacitance refer here:

https://brainly.com/question/28445252#

#SPJ11

The direction of the deflection of the wire will be determined by Fleming's left-hand rule. Here force will be perpendicular to both current and the magnetic field. So wire will deflect in a perpendicular direction to magnetic field.

Fleming's left-hand rule says if you point your thumb in the direction of the current, and finger can be in the direction of the magnetic field, then palm faces direction of the force.

We are placing two magnets as north pole of one magnet near the wire, and the south pole of the second magnet on the opposite side near the wire.

When the switch closed , wire will deflect perpendicular to the direction of the magnetic field.

Wire carries an electric current and when it comes with the magnetic field created by magnets,  a force will be exerted on the wire. This direction will say using Fleming's left-hand rule.  

Here force will be perpendicular to both current and the magnetic field. So wire will deflect in a perpendicular direction to magnetic field.

Learn more about magnetic field:

https://brainly.com/question/29441713

#SPJ4

This issue can be resolved by applying the momentum conservation principle. The total amount of momentum prior to and following the impact are equal. This can be expressed as:

(M1 + M2)vf = m1v1 + m2v2

m1 equals 200 kilograms (mass of wrestler 1)

v1 = 2.3 m/s (velocity of wrestler 1) (velocity of wrestler 1)

v2 = 2.9 m/s (velocity of wrestler 2) (velocity of wrestler 2)

m2 = the wrestler's mass two (unknown)

vf is the wrestlers' combined final speed before the collision (which we know is zero)

It's the same response we previously received. The problem is that the negative sign shows that Wrestler 2's velocity is moving in the opposite direction from Wrestler 1's velocity. Wrestler 2 is therefore traveling against the current. To gather the wrestlers in bulk

If r 2 is 2, we can omit the minus sign and use the absolute value instead:

As a result, wrestler 2 weighs roughly 158.62 kg.

In order to change the momentum of an object, you must exert a certain amount of force over a specific period of time. It is  because of this. For instance, when you strike a ball with a cricket bat, you exert power temporarily (in this case, very briefly) in order to change (or transfer) the momentum of the ball. |m2| = 158.62 kg

To know more about collision visit:-

brainly.com/question/30636941

#SPJ9

A strong magnet's poles are crossed by a cable conducting a 29.0 a current. The wire feels a 2.15 n pull on its 2.00-centimeter length in the field while it is perpendicular to the magnet's magnetic field. The average field strength of the magnet is 3.71 T.

The force on a wire of length L carrying a current I in a magnetic field B is given by the formula F = BIL sinθ, where θ is the angle between the wire and the magnetic field. Since the wire is perpendicular to the field, sinθ = 1, and we can simplify this equation to F = BIL.

We are given the current I, the length L = 2.00 cm, and the force F = 2.15 N. Plugging these values into the equation, we get:

2.15 N = B × 29.0 A × 0.02 m

Solving for B, we get:

B = 2.15 N / (29.0 A × 0.02 m)

= 3.71 T

To learn more about magnetic fields

https://brainly.com/question/11514007

#SPJ4

The rate at which the bullets are fired is 200 bullets/min, or 3.33 bullets/s. The magnitude of the average force on Superman's chest from the stream of bullets is approximately 78,299 N.

To calculate the magnitude of the average force on Superman's chest from the stream of bullets, we can use the equation for impulse:

I = FΔt

where I is the impulse, F is the force, and Δt is the time interval over which the force is applied.

Assuming that the bullets rebound straight back with no change in speed, the time interval over which each bullet is in contact with Superman's chest is given by:

Δt = 2l/v

where l is the thickness of Superman's chest, and v is the velocity of the bullet.

Substituting the given values, we get:

Δt = 2(0.1 m)/(680 m/s)

= 2.94 × 10^-4 s

The total impulse delivered to Superman's chest by each bullet is equal to its momentum change, which is given by:

I = Δp = 2mv

where m is the mass of the bullet, and v is its velocity.

Substituting the given values, we get:

I = 2(5.1 × 10^-3 kg)(680 m/s)

= 6.92 Ns

The rate at which the bullets are fired is 200 bullets/min, or 3.33 bullets/s. Therefore, the total impulse delivered to Superman's chest per second is:

I_tot = 3.33 bullets/s × 6.92 Ns/bullet

= 23.04 Ns/s

The average force on Superman's chest can be calculated by dividing the total impulse by the time interval over which it is delivered:

F_avg = I_tot/Δt

= 23.04 Ns/s / 2.94 × 10^-4 s

= 78,299 N

This is an enormous amount of force, far greater than any normal human could withstand. However, since Superman is a fictional character with superhuman strength and invulnerability, he can withstand this force without harm.

To learn more about magnitude

https://brainly.com/question/14452091

#SPJ4

The unit abbreviation that represents a measurement of force is C. N, which stands for Newton.

ewton is the force unit derived from the International System of Units (SI). It is named after Sir Isaac Newton, widely acknowledged as one of the most influential scientists of all time. The force required to accelerate a mass of one kilogram at a rate of one meter per second squared (m/s2) is referred to as one Newton.

Choice A, m/s, addresses an estimation of speed or speed (meters each second), while

choice B, m/s², addresses an estimation of speed increase (meters each second squared), which is connected with force, however not the unit of power itself.

Choice D, N/s, addresses an estimation of the pace of progress of power after some time, which is certainly not a generally involved unit in physical science.

know more about force visit :

https://brainly.com/question/13191643

#SPJ1

The change in internal energy of the system is 79 J. The answer is option a.

Internal energy is the total energy that a system possesses as a result of the random motion and interactions of its constituent particles, such as atoms and molecules. The change in internal energy of the system is given by the first law of thermodynamics as,

ΔU = Q - W

where ΔU is the change in internal energy, Q is the heat absorbed by the system, and W is the work done on the system by the surroundings.

Substituting the given values, we get:

ΔU = 196 J - 117 J

ΔU = 79 J

Option a is correct.

To know more about internal energy, here

brainly.com/question/2795732

#SPJ4

the given values, we get:m = 2(150 J) / (v = sqrt(2gh)) = 2(150 J) / sqrt(2(3.71 m/s²)(4.00 m))m ≈ 12.8 kg The mass of the object is approximately 12.8 kg.

When m is set to 15.0 kg and allowed to fall through 4.00 m, it gives 150.0 J of kinetic energy to the drum. The acceleration due to gravity is 3.71 m/s².What is kinetic energy?Kinetic energy is the energy of motion, and it is a scalar quantity that depends on an object's mass and velocity. Kinetic energy can be calculated using the following

formula:K.E. = 1/2mv²where m is the mass of the object and v is the velocity of the object.What is the given kinetic energy?The given kinetic energy is 150 J.What is the mass of the object?Using the formula for kinetic energy, we can rearrange it to solve for m. Thus, we get:K.E. = 1/2mv² ⇒ 2K.E. = mv² ⇒ m = 2K.E. / v²Substituting

The following values are obtained from the given ones:m = 2(150 J) / (v = sqrt(2gh)) = 2(150 J) / sqrt(2(3.71 m/s2)(4.00 m)). m ≈ 12.8 kg The thing weighs about 12.8 kg.

To learn more about : approximately

https://brainly.com/question/12785175

#SPJ11

The correct statements are the largest voltage appears across the capacitor with the smallest capacitance and the capacitor with the smallest capacitance has the smallest charge. Here options B and E are the correct answer.

When three unequal capacitors are connected in series across a battery, the charge on each capacitor is the same because they are connected in series. The equivalent capacitance of the circuit is less than any of the individual capacitances because capacitors in series add inversely.

The voltage across each capacitor depends on its capacitance, as well as the equivalent capacitance of the circuit and the applied voltage of the battery. The voltage across each capacitor can be calculated by the formula V = Q/C, where V is the voltage, Q is the charge, and C is the capacitance.

Since the capacitors are connected in series, the voltage across each capacitor is proportional to its capacitance. Therefore, the largest voltage appears across the capacitor with the smallest capacitance, and the smallest voltage appears across the capacitor with the largest capacitance.

The charge on each capacitor is directly proportional to its capacitance, and inversely proportional to the voltage across it. Therefore, the capacitor with the smallest capacitance has the smallest charge, and the capacitor with the largest capacitance has the largest charge.

To learn more about capacitors

https://brainly.com/question/17176550

#SPJ4

The work required to raise the pinnacle 12 meters of the chain to the top of the building is 13,139.6 Joules.

weight = mass x acceleration due to gravity

weight = 22 kg x 9.8 m/s² = 215.6 N

for this reason, the work required to raise the pinnacle 12 meters of the chain is:

work = force x distance = weight x distance = (215.6 N) x (61 m) = 13,139.6 J

Work is defined as the product of the force acting on an object and the displacement of the object in the direction of the force. Work is a scalar quantity, meaning it has magnitude but no direction.  Work is an important concept in many areas of physics, including mechanics, thermodynamics, and electromagnetism.

In mechanics, work is used to describe the energy required to move an object or to change its velocity. In thermodynamics, work is used to describe the energy required to change the state of a system. In electromagnetism, work is used to describe the energy required to move a charged particle in an electric field or to change the magnetic field in a given region. Work is a fundamental concept in physics and is essential for understanding the behavior of many physical systems.

To know more about Work visit here:

brainly.com/question/31050706

#SPJ4

Over-watering and plowing can have several negative effects on the land used for grain production. Over-watering can lead to waterlogging and salinization, which can reduce the fertility of the soil and harm crops. It can also lead to soil erosion and the depletion of nutrients in the soil.

The soil's capacity to absorb water and air can be reduced by soil compaction, which can result from overwatering and waterlogging. Both soil erosion and the demise of helpful microbes in the soil might result from this. Moreover, excessive irrigation can cause nutrient leaching, which removes vital nutrients from the soil.

Contrarily, ploughing can result in soil erosion and compaction, which can have a detrimental impact on crop yields. Plowing can also weaken the soil's structure, which lowers the soil's capacity to retain water and raises the likelihood of soil erosion. Plowing can also destroy beneficial soil microbes, which lowers soil fertility and harms the soil's overall health.

Learn more about plowing here:

https://brainly.com/question/7570264

#SPJ1

The net magnetic field B between two circular wire loops carrying the same current can be equal to zero in the region between the loops if the loops are perpendicular to each other.

To know more about magnetic field

https://brainly.com/question/28701572

#SPJ4

The velocity of the water through cross section [tex]A_1[/tex] is approximately 2.26 m/s.

According to the principle of continuity, the mass flow rate of water through the pipe must remain constant. This means that the product of the cross-sectional area and velocity of the water must be constant along the pipe. Mathematically, we can express this as:

[tex]A_1v_1 = A_2v_2[/tex]

where [tex]A_1[/tex] and [tex]A_2[/tex] are the cross-sectional areas of the pipe at sections 1 and 2, respectively, and [tex]v_1[/tex] and [tex]v_2[/tex] are the velocities of the water at sections 1 and 2, respectively.

We also know that the pressure difference between sections 1 and 2 is 104 Pa. Using Bernoulli's equation, we can relate this pressure difference to the velocity difference between the two sections:

[tex]P_1[/tex] + 1/2ρ[tex]v_1^2[/tex]  =[tex]P_2[/tex]  + 1/2ρ[tex]v_2^2[/tex]

where[tex]P_1[/tex] and [tex]P_2[/tex] are the pressures at sections 1 and 2, respectively, and ρ is the density of water.

Assuming the pipe is open to the atmosphere at both ends, we can set [tex]P_1[/tex] = [tex]P_2[/tex]= [tex]P_a_t_m[/tex], where [tex]P_a_t_m[/tex] is the atmospheric pressure.

Substituting the expression for [tex]A_1v_1[/tex] from the continuity equation into the Bernoulli's equation, we get:

[tex]P_a_t_m[/tex] + 1/2ρ[tex]v_1^2[/tex]  = [tex]P_a_t_m[/tex] + 1/2ρ[tex]v_2^2[/tex] + 104

Canceling out the atmospheric pressure terms, simplifying, and solving for [tex]v_1[/tex], we get:

[tex]v_1[/tex] = [tex]v_2[/tex] * sqrt[tex](A_2/A_1)[/tex] * sqrt(1 - 2104/(ρ[tex]v_2^2[/tex] ))

Substituting the given values, we get:

[tex]v_1[/tex] = 6 m/s * sqrt(1/4) * sqrt(1 - 2104/([tex]10006^2[/tex])) ≈ 2.26 m/s

For more such questions on velocity, click on:

https://brainly.com/question/25905661

#SPJ11

d. Nothing happens because the event object isn't passed to the function for the event handler.

Assuming the code example 8-1 you are referring to is a JavaScript code example that adds an event listener to all h2 elements in the document, the answer to your question would be: Nothing happens because the event object isn't passed to the function for the event handler.

In the code example, the event object is not passed as a parameter to the function that handles the click event, so the function cannot access the event object's properties and methods.

Without the event object, the function cannot determine which h2 element was clicked or perform any actions in response to the click event. Therefore, the function will not add the "minus" class to the clicked element or hide/show its next sibling.

To learn more about JavaScript here:

https://brainly.com/question/28448181

#SPJ11

A dart is loaded into a spring-loaded toy dart gun by pushing the spring in by a distance d. for the next loading, the spring has compressed a distance 6d. It requires 36 times more work to load the second dart compared to the first.

To determine the amount of work required to load the second dart compared to the first, we can use the formula for work done on a spring:
Work = (1/2) * k * x^2
Here, k is the spring constant and x is the distance the spring is compressed.
For the first dart, the work required is:
Work1 = (1/2) * k * d^2
For the second dart, the spring is compressed by a distance of 6d, so the work required is:
Work2 = (1/2) * k * (6d)^2
Now, we can find the ratio of the work required for the second dart to that of the first:
Work2 / Work1 = [(1/2) * k * (6d)^2] / [(1/2) * k * d^2]
The spring constant k and (1/2) are common factors and can be cancelled out:
Work2 / Work1 = (6d)^2 / d^2
By squaring 6d:
Work2 / Work1 = 36d^2 / d^2
The d^2 terms cancel out, leaving:
Work2 / Work1 = 36

For more such questions on distance

brainly.com/question/28529268

#SPJ11

The magnitude of the centripetal force exerted by the string on the ball is 4.2 N.

Centripetal force is the force that acts on an object moving in a circular path, directed toward the center of the circle. It is required to maintain the object's circular motion and is proportional to the object's mass, the square of its speed, and inversely proportional to the radius of the circle.

The centripetal force (Fc) exerted on an object moving in a circle is given by, Fc = m * a

where m is the mass of the object and a is its centripetal acceleration.

In this case, m = 0.35 kg and a = 12 m/s^2. Therefore:

Fc = (0.35 kg) * (12 m/s^2) = 4.2 N

To know more about centripetal force, here

brainly.com/question/28849632

#SPJ4