Which of the following is not a characteristic of electromagnetic light waves?

A. They can be reflected and refracted
B. They obey the formula: velocity = wavelength x frequency
C. They can't travel through a vacuum
D. They travel at approximately 3 x 10 8 meters per second

1) current

2) in series

3) voltage

4) In parallel

Ammeters are connected in series with the component or part of the circuit being measured, so that the entire current flows through the ammeter. This means that the ammeter must have a very low resistance, so that it does not significantly alter the current being measured. Typically, ammeters have a built-in shunt resistor to achieve this low resistance.

On the other hand, voltmeters are connected in parallel with the component or part of the circuit being measured, so that they measure the voltage across the component or part. This means that the voltmeter must have a very high resistance, so that it does not draw significant current from the circuit and alter the voltage being measured. Typically, voltmeters have a built-in series resistor to achieve this high resistance.

Learn more about ammeter:https://brainly.com/question/30849022

#SPJ1

Sounds can be changed in a variety of ways depending on the source of the sound and the type of change you want to make. Here are a few examples:

The cause of the change depends on the type of change being made. For example, changing the pitch of a sound is caused by altering the frequency of the sound wave, while changing the volume is caused by altering the amplitude of the sound wave.

In general, changes to sound waves can be caused by physical manipulation of the sound source, such as adjusting the properties of a musical instrument, or by electronic processing of the sound signal using digital signal processing techniques.

Learn about sounds here https://brainly.com/question/95976

#SPJ1

The maximum height to which the stone can rise, given that the work done is 40 J, is  40.82 m

First, we shall list out the given parameters from the question. This is given below:

We can obtain the maximum height to which the stone can rise as follow

Wd = mgh

40 = 0.10 × 9.8 × h

40 = 0.98 × h

Divide both sides by 0.98

h = 40 / 0.98

h = 40.82 m

Thus, the maximum height to which the stone can rise is 40.82 m

Learn more about height:

https://brainly.com/question/22740770

#SPJ1

The initial velocity of the ball that was thrown downward from a height of  35 m is 4.53 m/s².

Velocity is the rate of change of displacement.

To calculate the initial velocity of the ball, we use the formula below,

Formula:

Where:

From the question,

Given:

Substitute these values into equation 1 and solve for u

Hence, the initial velocity is 4.53 m/s².

Learn more about velocity here: https://brainly.com/question/24445340

#SPJ1

If we know the mass of the ball, the spring constant, and the maximum displacement (or amplitude) of the ball from its equilibrium position, we can calculate the speed at which the ball passes through its equilibrium position each time.

The speed at which the ball passes its equilibrium position each time depends on the amplitude and period of its motion.

Assuming the ball is executing simple harmonic motion, the time period (T) of the motion can be calculated using the formula:

T = 2π√(m/k)

where m is the mass of the ball and k is the spring constant.

Once we know the time period of the motion, we can calculate the speed at which the ball passes through its equilibrium position using the formula:

v = A/T

where A is the amplitude of the motion.

If the amplitude of the motion is not given, we can assume that it is equal to the maximum displacement of the ball from its equilibrium position. For a mass-spring system, this maximum displacement is equal to the amplitude of the oscillation.

For such more question on equilibrium:

https://brainly.com/question/517289

#SPJ11

The star located 10,000 light-years away from the galactic center would have a higher rotational velocity than the star located 26,000 light-years away.

The galaxy's rotational speed is not constant across its radius. The Milky Way, like most galaxies, has a dark matter halo that encloses the visible matter. The circular velocity profile of the Milky Way, which is almost flat beyond the Sun's location, offers a measure of the total mass distribution. The orbital velocities of material at various radii around the galactic center, such as gas and stars, can be measured to determine this profile.

Galactic rotation is characterized by Kepler's third law, which states that for a galaxy with a spherically symmetric mass distribution, the rotation speed is proportional to the square root of the distance to the center. As a result, a star that is closer to the galactic center would have a higher rotational speed than one that is farther away.

Since we have two stars, one located 10,000 light-years from the galactic center and the other located 26,000 light-years from the galactic center, we can quickly determine which star has the higher rotational velocity using Kepler's third law. The star closer to the galactic center, which is located 10,000 light-years away, would have a higher rotational velocity than the star located 26,000 light-years away from the galactic center.

Know more about galactic center here:

https://brainly.com/question/30217143

#SPJ11

The direction of the induced electric field is given by Lenz's law, which states that the direction of the induced field is such that it opposes the change in magnetic flux that is inducing it.

The movement of the bar upward in the field is what in this instance is responsible for the shift in magnetic flux. The induced electric field will induce a current in the bar that flows in a direction that produces a magnetic field that opposes the upward field in order to counteract this shift in flux.

We can calculate the direction of the current flow in the bar using the right-hand rule for current. Our fingertips will curl in the direction of the magnetic field created by the current if we point our thumb in the direction of the induced current.

For such more question on magnetic flux:

https://brainly.com/question/16234377

#SPJ11

The maximum distance at which the eye can resolve two headlights at night, given a pupil diameter of 0.4 cm, is approximately 11,937.3 meters or 11.937 kilometers.

To calculate the maximum distance at which the eye can resolve two headlights at night, we can use the formula for the angular resolution of the human eye, which is based on the Rayleigh criterion:

θ = 1.22 * (λ / D)

Where:
θ = angular resolution in radians
λ = wavelength of light (average wavelength of visible light is approximately 550 nm, or 5.5 x 10^-7 meters)
D = diameter of the aperture (pupil diameter, given as 0.4 cm or 0.004 meters)

First, calculate the angular resolution:

θ = 1.22 * (5.5 x 10^-7 m / 0.004 m) = 1.678 x 10^-4 radians

Now, to find the maximum distance (d) at which the eye can resolve two headlights, we can use the formula

d = L / tan(θ)
Where:
L = distance between the headlights (assuming a standard separation of 2 meters)
Before calculating, we need to make sure that the angular resolution (θ) is in the same unit (radians) as the tangent function requires:
θ = 1.678 x 10^-4 radians
Now, calculate the maximum distance:
d = 2 m / tan(1.678 x 10^-4) ≈ 11937.3 meters
Therefore, the maximum distance at which the eye can resolve two headlights at night, given a pupil diameter of 0.4 cm, is approximately 11,937.3 meters or 11.937 kilometers.

For more such questions on distance , Visit:

https://brainly.com/question/25825784

#SPJ11

When the bird drops the clam from a height, the potential energy of the clam is converted into kinetic energy. As the clam falls, it gains kinetic energy and loses potential energy.

When the clam hits the rock, the kinetic energy is converted into other forms of energy, such as sound and heat, and the clam shell breaks.

Therefore, the correct energy conversion when the clam is dropped is from potential energy to kinetic energy, followed by a conversion of kinetic energy into other forms of energy.

To know more about bird drops

https://brainly.com/question/13613150

#SPJ4

The power exerted by the crane during the lift is 82,404 watts.

To calculate the power exerted by the crane while lifting a 1400 kg Honda at a constant velocity of 6.0 m/s, follow these steps:

1. First, calculate the gravitational force acting on the Honda using the equation F = m * g, where F is the force, m is the mass of the Honda (1400 kg), and g is the acceleration due to gravity (approximately 9.81 m/s²).

  F = 1400 kg * 9.81 m/s²
  F = 13734 N

2. Next, calculate the work done by the crane to lift the Honda at a constant velocity. Work is given by the equation:

W = F * d, where W is the work done, F is the force calculated in step 1, and d is the distance traveled (which can be calculated as the velocity multiplied by time).

However, since the crane is lifting at a constant velocity, the work done equals the force applied.

  W = F
  W = 13734 J

3. Finally, calculate the power exerted by the crane. Power is given by the equation P = W / t, where P is the power, W is the work done (calculated in step 2), and t is the time taken to lift the Honda.

Since the Honda is lifted at a constant velocity of 6.0 m/s, the power can be calculated as P = F * v, where F is the force and v is the velocity.

  P = 13734 N * 6.0 m/s
  P = 82404 W

Therefore, the power exerted by the crane is 82,404 watts.

To know more about power click here:

https://brainly.com/question/30817666

#SPJ11

The power for the voltage source is -6.5744 W and the power for the current source is 0.02424 W (both to three significant digits).

To find the voltage Vab, we can use the voltage divider rule, which states that the voltage across a resistor in a series circuit is proportional to its resistance. In this case, Vab is the voltage across R2 and R3 in series, so:

Vab = Vo * (R2 + R3) / (R1 + R2 + R3)

= 9.84 * (9 + 6) / (10 + 9 + 6)

= 4.608 V

To find the current Ij, we can use Kirchhoff's current law, which states that the total current flowing into a junction is equal to the total current flowing out of the junction. In this case, the current flowing into node b is equal to the current flowing out of node b, so:

Ij = (Vc - Vab) / R3

= (4.296 - 4.608) / 6

= -0.052 A

Note that the negative sign indicates that the current is flowing in the opposite direction of the assumed direction.

To find the power for the voltage and current source, we can use the formulas P = V * I and P = I^2 * R, respectively. For the voltage source, the power is:

Pvg = Va * (Vc - Va) / R1

= 16 * (4.296 - 16) / 10

= -6.5744 W

Note that the negative sign indicates that the power is being dissipated, rather than generated.

For the current source, the power is:

Pig = Ij^2 * R2 = (-0.052)^2 * 9 = 0.02424 W

To learn more about current source

https://brainly.com/question/14696285

#SPJ4

Complete question:

m mo Vs( R1 = 10 kN2 R2 =9 k12 R3 = 6 kN2 The measured nodal voltages are: Va = 16 V Vo = 9.84 V Vc = 4.296 V Find voltage Vab and the current 11. Vab = mA Ij = (within three significant digits) What is the power for the voltage and current source in watts? Pvg = Pig = (within three significant digits)

The average power generated by the lifting force is equal to the total work done by the lifting force divided by the time taken.

The total work done by the lifting force is equal to the mass of the helicopter times the change in its gravitational potential energy.The change in its gravitational potential energy is equal to its mass times the gravitational acceleration times its change in height.

Therefore, the average power generated by the lifting force is equal to the mass of the helicopter times the gravitational acceleration times the change in height, divided by the time taken. In this case, the average power is equal to 840 kg times 9.81 m/s2 times 7.7 m, divided by 4.0 s, which is equal to 203 kW. Therefore, the average power generated by the lifting force is 203 kW.

know more about Acceleration here

https://brainly.com/question/12550364#

#SPJ11

The horizontal force that her wrist must exert on her hand is 2,128 N.

Consider the rotational motion of the ice skater and the forces acting on her body.

The centripetal force required to keep the ice skater moving in a circle is provided by the tension force in her arms.

We can use the following equation to find the tension force:

F = mω²r

where F is the tension force, m is the mass of the ice skater, ω is the angular velocity (in radians per second), and r is the radius of the circle formed by the outstretched arms (i.e., half the distance between the hands).

First, let's calculate the radius:

r = 1.50 m / 2

  = 0.75 m

Next, let's calculate the angular velocity:

ω = 2.5 turns/s x 2π radians/turn = 15.7 radians/s

Now, let's calculate the mass of the ice skater's hands:

m_hands = 0.0125 x 50 kg = 0.625 kg

Finally, let's use the equation above to find the tension force:

F = mω²r = (50 kg + 2 x 0.625 kg) x (15.7 radians/s)² x 0.75 m

= 2,128 N

Therefore, the horizontal force that her wrist must exert on her hand is 2,128 N.

Learn more about  horizontal force

brainly.com/question/2037071

#SPJ11

The common difference is (26-a)/4, the first term is (3a+26)/4, and the 20th term is (81a-494)/4.

Let's call the first term of the arithmetic progression "a" and the common difference "d".

Then, the second term would be "a + d", the third term would be "a + 2d", and so on.

The second term is "a + d" and the eighth term is "a + 7d".

The sum of the second and eighth term is given as 52:

(a + d) + (a + 7d) = 52

Simplifying the equation:

2a + 8d = 52

Dividing both sides by 2:

a + 4d = 26

Now, to find the difference between the third terms:

The third term is "a + 2d".

The difference between the third and second term is the common difference "d".

So, d is the difference between (a + 2d) and (a + d).

d = (a + 2d) - (a + d)

d = a + 2d - a - d

d = d

Therefore, we know nothing about the difference between the third terms.

To find the values asked in the question:

i. The common difference is given as:

a + 4d = 26

4d = 26 - a

d = (26 - a)/4

ii. The first term can be found by substituting the common difference into the equation:

a + d = a + [(26 - a)/4] = (4a + 26 - a)/4 = (3a + 26)/4

iii. The 20th term can be found using the formula for the nth term of an arithmetic progression:

a_n = a + (n - 1)d

a_20 = a + 19d

Substituting the value of d:

a_20 = a + 19[(26 - a)/4]

a_20 = (81a - 494)/4

Learn more about arithmetic progression here: https://brainly.com/question/18828482

#SPJ1

The change in the internal energy of the system can be calculated using the first law of thermodynamics, which states that the change in the internal energy of a system is equal to th added to the system minus the work done by the system on the surroundings.

The formula for this is:ΔU = Q - W where ΔU is the change in internal energy, Q is the heat added to the system, and W is the work done by the system on the surroundings. In this case, 5 kJ of heat is added to the system, and the system does 2 kJ of work on the surroundings. Therefore, the change in internal energy is:ΔU = Q - WΔU = 5 kJ - 2 kJΔU = 3 kJSo, the change in the internal energy of the system is 3 kJ.
The change in internal energy of the system can be calculated using the first law of thermodynamics: ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat added to the system, and W is the work done by the system. In this case, Q = 5 kJ and W = 2 kJ.

So, ΔU = 5 kJ - 2 kJ = 3 kJ.

The change in the internal energy of the system is 3 kJ, considering we neglect the change in the bulk energy.

Learn more about internal energy here:

https://brainly.com/question/14668303

#SPJ4

When unpolarized light passes through a polarizer at 60 degrees from the vertical, the intensity of the light is halved.

Unpolarized light, which consists of light waves vibrating in all planes perpendicular to the direction of propagation, does not have a specific direction of oscillation. This means that its electric field is randomly polarized in all directions perpendicular to the direction of motion. Polarization refers to the direction in which the electric field is oscillating.

Polarized light waves have an electric field that is oscillating in only one direction, whereas unpolarized light has an electric field that is oscillating in all directions perpendicular to the direction of motion. A polarizer is a filter that polarizes light waves by allowing only those waves that are oscillating in a particular direction to pass through. If unpolarized light passes through a polarizer at a 60-degree angle to the vertical, only half of its intensity will be able to pass through.

To learn more about Unpolarized light :

https://brainly.com/question/30739829

#SPJ11

The length of the pendulum is approximately 1.04 m, rounded to two significant figures.

The period (T) of a pendulum is given by T = [tex]2π√(L/g)[/tex], where L is the length of the pendulum and g is the acceleration due to gravity (approximately 9.81 [tex]m/s^2[/tex]). The frequency (f) of the pendulum is simply the inverse of the period, so f = 1/T.

Given that the frequency of the pendulum is 1.5 Hz, we can calculate the period as follows: f = 1/T 1.5 Hz = 1/T T = 1/1.5 s T = 0.667 s Now, we can use the period formula to find the length of the pendulum: T = 2π√(L/g) 0.667 s =[tex]2π√[/tex]([tex]L/9.81 m/s^2[/tex]) 0.667 s/([tex]2π[/tex]) = [tex]√(L/9.81 m/s^2[/tex]) 0.106 [tex]s^2/m =[/tex] [tex]L/9.81 m/s^2 L[/tex]= 1.04 m

Therefore, the length of the pendulum is approximately 1.04 m, rounded to two significant figures. It's important to note that the length of a pendulum affects its period and, consequently, its frequency.

Learn more about frequency here:

https://brainly.com/question/29739263

#SPJ4

Audible things: birds singing, wind howling. Clouds forming and lightning are not audible because they don't produce sound waves.

Of the choices given, two things are discernible: birds singing in the trees and wind yelling.

Mists framing and lightning streaking across the sky are not perceptible on the grounds that they don't deliver sound waves. Mists framing are a visual peculiarity brought about by changes in temperature and dampness in the air, and lightning produces electromagnetic waves however not sound waves.

Birds singing in the trees and wind crying are both perceptible in light of the fact that they produce sound waves. Birds produce sound by vibrating their vocal ropes, and the subsequent sound waves can head out through the air to be heard by people. Wind can make objects vibrate, delivering sound waves that can likewise be heard by people.

To learn more about audible wave, refer:

https://brainly.com/question/30065253

#SPJ4

Based on the statement made by the student, The student's statement that the puck slid a bigger distance before stopping when it was moving faster is correct.

The above is because the kinetic energy of an object in motion is proportional to its mass and the square of its velocity. When an object is moving faster, it has more kinetic energy, and it takes more work to stop it. In the case of the puck, the frictional force acting on it was not strong enough to overcome the kinetic energy of the puck when it was moving faster, resulting in a longer sliding distance before it came to a stop.

However, the student's conclusion that they should hit their brakes twice as far from a stop sign when driving at 40 mph instead of 20 mph to stop their car in time is not necessarily accurate. While it is true that a car moving at a higher speed has more kinetic energy and requires more work to stop, the distance required to stop the car depends on several factors, such as the mass of the car, the efficiency of the brakes, and the condition of the road surface.

Read more about distance  here:

https://brainly.com/question/26550516

#SPJ1

It will take 7.50 seconds to  cross a railway platform 165m long, when a train is moving at a speed of 132kmph. if the length of the train is 110 meters.

At the point when a train crosses a stage, the all out distance it covers is the amount of the length of the train and the length of the stage. The time it takes to cover this distance relies upon the speed of the train, which is given in km/h. We can change this over completely to m/s by duplicating by 1000/3600.

For this situation, the speed of the train is 132 km/h, which is around 36.67 m/s. The complete distance the train should cover is the length of the train in addition to the length of the stage, which is 110 m + 165 m = 275 m.

To ascertain the time it takes to cover this distance, we can utilize the equation: time = distance/speed. Subbing the given qualities, we get:

time = 275 m/36.67 m/s

≈ 7.50 s

Accordingly, it will require around 7.50 seconds for the train to cross the 165 m long stage, accepting that there is no postponement because of some other factors like speed increase or deceleration.

To learn more about speed and time, refer:

https://brainly.com/question/17153206

#SPJ4

Option b. 4.86 million km2 of sea ice would remain in 2020 if the decline rate continued at 10% per decade.

Ocean ice is a significant piece of the World's environment framework, reflecting daylight and managing the planet's temperature. Be that as it may, environmental change has caused a decrease in how much ocean ice over ongoing many years, with a typical decay pace of around 10% each 10 years. This intends that for each decade that passes, how much ocean ice remaining is 90% of the earlier ten years' sum.

To work out how much ocean ice would stay in a specific year, we can utilize the recipe: remaining ice = (1-0.1)^n * beginning ice, where n is the quantity of many years that have passed and starting ice is how much ocean ice in the beginning year. For instance, in the event that there were 6 million km2 of ocean ice in the year 2000 and 20 years (twenty years) have passed, we can compute the excess ice in 2020 as follows: remaining ice = (1-0.1)^2 * 6 million km2, which approaches around 4.86 million km2.

This computation features the huge loss of ocean ice over a generally brief timeframe, with practically 20% of the ice vanishing more than twenty years. This deficiency of ocean ice has extensive ramifications for worldwide environment examples, natural life, and human networks living in the Cold.

To learn more about sea ice declining rate, refer:

https://brainly.com/question/3734286

#SPJ4

The complete question is:

every decade, the sea ice declines by 10 percent. if there were 6 million km2 of sea ice in the year 2000, how much would remain in 2020? group of answer choices are a. 7.85 b.4.86 c. 6.80 d. 3.67

The heavier block has the larger final kinetic energy after the force acts.

Here's the step-by-step explanation:

1. Both the lighter and heavier blocks are initially at rest, so their initial momenta and kinetic energies are both zero.

2. The same force F is applied to each block for a distance of 1 meter.

3. Since force and distance are the same for both blocks, they will both gain the same amount of work done on them (W = F × d).

4. Work done on an object is equal to the change in its kinetic energy (W = ΔKE).

5. As both blocks have the same amount of work done on them, they will both have the same increase in kinetic energy.

6. However, the heavier block initially had a higher mass, so its final kinetic energy will be larger than the lighter block's final kinetic energy. This is because kinetic energy is directly proportional to mass (KE = 0.5 × m × v^2).

To know more about kinetic energy, refer here:

https://brainly.com/question/26472013#

#SPJ11

The total angle (in radians) the tires rotate through during the trip is 2573.32 radians.

As given, a boy rides his bicycle 1.44 km. The wheels have a radius of 28.0 cm. We have to calculate the total angle (in radians) that the tires rotate through during his trip. Let us calculate the circumference of the tire with the given radius. We know that the circumference of the tire

=> 2πr= 2 × 22/7 × 28 cm

=>  176 cm

=> 1.76 meters

Now, the boy rode his bicycle for a distance of 1.44 km which is equal to 1440 meters. Let the number of times the tire rotates be N.

Then, from the above calculation, we know that the distance traveled by each tire in one rotation is the circumference of the tire. Thus the distance traveled by both tires in one rotation is

2 × 1.76 = 3.52 meters.

Therefore, the number of rotations of the tire, N = distance traveled by both the tires/distance traveled by the boy

= 1440 / 3.52= 409.09 approx.

Now, we know that in one rotation of the tire, the angle (in radians) that it rotates through is equal to 2π radians. Therefore, in N rotations, the angle rotated by the tire (in radians) is equal to 2πN.

Substituting the value of N, we have the Angle rotated (in radians)

=> 2 × 22/7 × 409.09= 2573.32 radians approx.

To learn more about Angle :

https://brainly.com/question/29506154

#SPJ11

The force, in N, applied to the cannonball can be calculated using Newton's Second Law of Motion, which states that the force applied to an object is equal to its mass times its acceleration:

Force = mass x acceleration

Plugging in the given values, we get:

Force = 5 kg x 8 m/s^2 = 40 N

Therefore, the force applied to the cannonball was 40 N.

Based on the data collected from the three trials, we can find the average acceleration of the fan cart on a horizontal track. To do this, we will calculate the mean of the six acceleration values provided:

(0.642 + 0.622 + 0.651 + 0.618 + 0.664 + 0.604) / 6 = 3.801 / 6 = 0.634 m/s^2

Now, the mass of the fan cart is 480 g, which we will convert to kg:

480 g * (1 kg / 1000 g) = 0.48 kg

After adding 120 g to the cart, the new mass becomes:

0.48 kg + (120 g * 1 kg / 1000 g) = 0.48 kg + 0.12 kg = 0.60 kg

Next, we need to determine the gravitational force acting on the cart along the incline. This can be calculated using the formula:

F_gravity = m * g * sin(theta)

where m is the mass of the cart, g is the gravitational constant (approximately 9.81 m/s^2), and theta is the angle of inclination.

F_gravity = 0.60 kg * 9.81 m/s^2 * sin(4.5°) ≈ 0.60 kg * 9.81 m/s^2 * 0.078 ≈ 4.72 N

Now, we'll calculate the force exerted by the fan using the formula:

F_fan = m * a

where m is the mass of the cart, and a is the average acceleration calculated earlier.

F_fan = 0.60 kg * 0.634 m/s^2 ≈ 0.38 N

Since the gravitational force (4.72 N) is greater than the force exerted by the fan (0.38 N), the cart will not be able to overcome gravity and will accelerate down the incline.

To Learn More About Acceleration

https://brainly.com/question/460763

#SPJ11

The body position sense that orients us with respect to gravity and the immediate environment is a function of the vestibular system, which is located in the inner ear.

This system provides the brain with information about head position, acceleration, and movement, which in turn allows us to maintain balance and a sense of spatial orientation. Additionally, information from the eyes, muscles, and joints also contribute to body position sense, allowing us to integrate multiple sensory inputs and make accurate judgments about our position and movement in space. Overall, body position sense is a complex sensory and neural process that involves multiple inputs and processing centers in the brain.

To know more about body, here

brainly.com/question/10530344

#SPJ4

The work done by a weightlifter to lift a 420 N set of weights from ground level to a position over his head is 735 j.

To calculate the work done by a weightlifter who lifts a 420 N set of weights from ground level to a position over his head, a vertical distance of 1.75 m, assuming he moves the weights at a constant speed:

Use the formula given below:

W = F × d

where,

W = work done by the weightlifter

F = force applied

d = distance moved by the weightlifter

From the given data, the force applied by the weightlifter is 420 N, and the distance moved is 1.75 m.

W = 420 N × 1.75 m = 735 J

Therefore, the work done by the weightlifter is 735 J.

To know more about work click here:

https://brainly.com/question/24244140

#SPJ11

The terminal velocity of a 90-kg (including any equipment) skydiver who jumps out of a plane can be found using the given data: air density of 1.0 kg/m3, a frontal surface area of 1.0 m2, and a drag coefficient of 0.8.What is terminal velocity.

Terminal velocity is the maximum velocity that a falling object can reach when air resistance is equal to the gravitational force acting on it. This is the point at which an object can no longer accelerate because the opposing forces are balanced. Terminal velocity can be computed using the formula: v = √(2mg/ρACd)where: v is the terminal velocity m is the mass of the objectρ is the air density A is the frontal surface area Cd is the drag coefficient of the object g is the acceleration due to gravity(9.81 m/s²)Substituting the provided values: v = √(2(90 kg)(9.81 m/s²)/(1.0 kg/m³)(1.0 m²)(0.8)) = 72.22 m/s Therefore, the skydiver's terminal velocity is 72.22 m/s.

Learn more about here:

https://brainly.com/question/2654450

#SPJ4

When measuring angles of incidence and angles of refraction, always make sure to measure them from the normal line, which is perpendicular to the surface at the point of contact. This ensures accurate measurements and proper calculations in refraction scenarios.

When measuring angles of incidence and angles of refraction, it is essential to ensure that you always measure them using the correct tools or instruments.What is an angle?An angle is a measure of rotation, expressed in degrees, that two lines or sides create around a common point called the vertex. Two rays or lines originate from a single point and diverge in different directions to form an angle.Measuring anglesTo measure angles, you'll need a protractor, a device that's specifically built for this task. Place the protractor on the angle's vertex so that the base lines of the protractor are parallel to the lines or sides of the angle you're measuring.Angle of incidenceThe angle of incidence is the angle between the incident ray and the normal line to a surface, such as the surface of an optical lens, mirror, or prism. The angle of incidence is denoted by the Greek letter “θ” (theta).Angle of refractionThe angle of refraction is the angle between the refracted ray and the normal line to a surface, such as the surface of an optical lens, mirror, or prism. The angle of refraction is denoted by the Greek letter “θ” (theta).Therefore, when measuring angles of incidence and angles of refraction, it is essential to ensure that you always measure them using the correct tools or instruments. The angle measurement process is done using a protractor.

Learn more about angles of refraction here;

https://brainly.com/question/14760207

#SPJ4

To generate a magnetic field of strength 24e-6 T at the center of the loop, a current of approximately 4.4 A is required in a loop of wire with a radius of 0.035 m.

The magnetic field generated by a current-carrying loop of wire depends on the current and the geometry of the loop. The magnetic field strength at the center of the loop is given by the formula B = μ₀I/(2r), where B is the magnetic field strength, μ₀ is the magnetic constant (equal to 4π x 10^-7 T m/A), I is current, and r is the radius of the loop. In this case, we are given the magnetic field strength B and the radius of the loop r, and we want to find the current I that will produce that field strength. Rearranging the formula, we get I = 2Br/μ₀. Plugging in the given values, we get I = 2 x 24e-6 T x 0.035 m / (4π x 10^-7 T m/A), which simplifies to 1.2 A. Therefore, a current of 1.2 A is required in the loop of wire to generate a magnetic field of strength 24e-6 T at the center of the loop.

Learn more about current here:

https://brainly.com/question/12791045

#SPJ11