what will be the value of charges after the following code is executed? group of answer choices 7.00 14.00 21.00 28.00

If no packet is received as a response during a null scan, it is most likely because the targeted system has an active firewall or intrusion detection system that is blocking or filtering incoming traffic.

During a null scan, the most likely cause of no packet receipt is that the targeted system has an active firewall or intrusion detection system that is blocking or filtering incoming traffic. A null scan is a stealthy and passive scanning technique that is used by attackers to gather information about a target system without generating any traffic. A null scan is conducted by sending a TCP packet with all flags set to zero, which is known as a null packet or a null probe.A null scan can be used to detect open ports on a target system because if a port is closed, the target system should respond with a TCP RST (reset) packet. However, if the port is open, the target system will not respond with any packet because the TCP protocol requires an acknowledgement (ACK) packet in response to a SYN packet to establish a connection. Since a null packet has no flags set, it does not initiate a connection and does not receive any response.

Learn more about packet here:

https://brainly.com/question/17009080

#SPJ11

The type of cloud service that would allow you to provide a cloud-based application to your employees using their smartphones is Mobile cloud computing.

What is mobile cloud computing: Mobile cloud computing is a type of cloud computing that enables cloud computing services to be delivered to mobile devices such as smartphones, tablets, and other mobile devices. The mobile device is a client of the cloud service, which provides the services. The cloud computing infrastructure, which is hosted in data centers, is accessed over the internet.The following are some of the advantages of mobile cloud computing:Access to vast amounts of data and processing power on the cloud can improve the performance of mobile devices.Mobile cloud computing allows for the creation of applications that can run on a variety of devices, including smartphones and tablets, providing a consistent user experience regardless of the device in use.The ability to offload computationally expensive and energy-intensive tasks to the cloud, allowing for a longer battery life on mobile devices.What is Cloud-Based Application?A cloud-based application, often known as Software as a Service (SaaS), is a web-based application that is hosted and managed by a third-party service provider, who is responsible for its servers, databases, and maintenance. Cloud-based applications are accessed through a web browser or a mobile application, and they are typically charged on a subscription basis. These applications are scalable, available on-demand, and can be accessed from anywhere with an internet connection.What are Employees?An employee is an individual who works for a company or organization and is compensated for their time and effort. Employees are frequently categorized as either full-time or part-time, and they are required to follow the company's policies and procedures. Employees' responsibilities and job titles vary based on their positions in the company.

learn more about cloud service here:

https://brainly.com/question/29531817

#SPJ4

Digital documents that support concurrent editing and commenting enable real-time collaboration, simple change tracking, and distant collaboration.

Compared to in-person brainstorming sessions, working together on a digital document has significant advantages. The first benefit is that it enables real-time collaboration, allowing team members to work on the document concurrently without the need for follow-up meetings or emails. Second, it makes it simple to track changes, which makes it simpler to maintain track of various document versions. Last but not least, digital documents enable remote collaboration, which is crucial in the modern workplace where many teams operate remotely. Collaboration is facilitated via comment threads in digital documents, which also make it simple for team members to communicate and provide input.

learn more about document here:

https://brainly.com/question/13406067

#SPJ4

Only when you add multiple entries using the insert keyword does the mysql info function provide query information.

To learn more about MySQL, refer to:

https://brainly.com/question/29326730

The MySQL info() function only returns query information when you add multiple records with the INSERT keyword.

What is MySQL?

MySQL is a free, open-source relational database management system (RDBMS). It is a part of the LAMP stack (Linux, Apache, MySQL, PHP/Perl/Python).

What is the info() function?

The mysql_info() function in MySQL is a PHP built-in function that retrieves the number of affected rows by the previous MySQL operation. It also returns the last inserted ID if the operation was an insert query. The MySQL server returns detailed information for most queries performed by the user.

As a result, calling the info() function with no arguments provides information about the most recent query. However, if you execute an INSERT query with multiple records, the info() function returns the number of records affected by the operation.

For example: mysql_query (INSERT INTO mytable (name, phone) VALUES ('John Smith', '123-456-7890'); ('Jane Doe', '555-555-5555)); $info = mysql_info();echo $info; // returns "Records: 2 Duplicates: 0 Warnings: 0"

Here, the query inserts two records into the mytable table, and the info() function returns that two records were affected.

Learn more about MySQL here:

https://brainly.com/question/13267082

#SPJ11

The minimum amount of available buffer space advertised to the client by gaia.cs.umass.edu among these first five data-carrying tcp segments is 5840 bytes. James Lovelock, a British scientist, and Lynn Margulis, an American biologist, are the originators of the Gaia hypothesis.

In computing, buffer space is the amount of physical memory allocated to store data temporarily when it is being transmitted from one place to another. Buffers are often used in the transmission of data over a network. A buffer is a section of memory allocated for data storage when it is temporarily idle to be accessed or modified. It's also a type of output device that is utilized to get data from one place to another.

The units of data transmission between two TCP endpoints are called TCP (Transmission Control Protocol) segments. Segments are another name for TCP packets or datagrams. The term "segment" is employed because TCP divides data into manageable smaller pieces. The TCP protocol's packet structure is made up of a sequence number, an acknowledgment number, and a number of control flags. Describe Gaia. The term "Gaia" is used to refer to the Planet as a whole, including all of its ecological systems. Over the years, Gaia has been described in a variety of ways, from the Earth as a complicated system to the Earth as a single creature.

The minimal amount of available buffer space among the first five data-carrying TCP segments that gaia.cs.umass.edu advertises to the client is 5840 bytes. The initial ack that was received from the server contains the value.

Learn more about TCP segments

brainly.com/question/28119964

#SPJ11

The two statements that are not correct about Harvard architecture are:

1. It has reduced processor performance (performance bottleneck) because program and data cannot be accessed at the same time.
2. It has a higher hardware complexity as compared to von Neumann architecture.

The two statements that are not correct about Harvard architecture are:It has reduced processor performance (performance bottleneck) because program and data cannot be accessed at the same time. This is incorrect as Harvard architecture allows simultaneous access to program and data memory.It has a higher hardware complexity as compared to von Neumann architecture. This is also incorrect as Harvard architecture has a simpler hardware structure than von Neumann architecture.What is Harvard architecture?Harvard architecture is a computer architecture that separates the memory and processing units into two different systems. It has separate memory units for data and instruction processing, making it a more efficient and faster processing system. In the Harvard architecture, instructions and data are stored in different memory units, which are accessed by separate buses.The advantages of the Harvard architecture over the von Neumann architecture include faster processing speeds and simultaneous access to data and instructions, making it more efficient. The Harvard architecture is commonly used in microcontrollers, digital signal processors, and other embedded systems.

Learn more about Harvard architecture here: brainly.com/question/13487745

#SPJ11

The main difference between a hardlink and a symlink in Linux is that a hardlink creates another name for the same file, while a symlink creates a new file that points to the original file by its path.

In Linux, a hardlink and a symlink (symbolic link) are two types of links that can be used to reference a file.

A hardlink is a reference to an actual file on the file system, and it creates another name for the same file. The hardlink and the original file share the same inode, which contains the metadata of the file. If the original file is deleted, the hardlink still points to the same data and the file remains accessible. Hardlinks can only be created for files, not directories, and they can only reference files on the same file system.

On the other hand, a symlink is a reference to a file by its path, which can be absolute or relative. A symlink is a separate file that contains the path to the original file, and it creates a new file that points to the original file. If the original file is deleted, the symlink will be broken and no longer valid. Symlinks can reference files or directories, and they can reference files on different file systems.

In summary, the main difference between a hardlink and a symlink is that a hardlink is a reference to the actual file on the file system, while a symlink is a reference to the file by its path. Hardlinks create another name for the same file, while symlinks create a new file that points to the original file. Additionally, hardlinks can only reference files on the same file system, while symlinks can reference files on different file systems.

To learn more about Linux, visit:

https://brainly.com/question/15122141

#SPJ1

Live migration is a process of moving a virtual machine from one physical host to another without causing any downtime. It's a popular feature in server virtualization that allows system administrators to transfer running virtual machines between physical hosts.

For such more question on virtualization

https://brainly.com/question/23372768

#SPJ11

They decided not to use the patient social security number as the key field of the table because the latter is personal information. As a result, the database developers settled on patient num as the primary key, since it is a unique identifier that cannot be associated with any personal information.

What is a database?

A database is a collection of data that is organized in such a way that it can be easily accessed, managed, and updated. A database is generally made up of tables, each of which is made up of rows and columns. In a database, tables are used to organize and store data.

What is a patient's social security number?

A patient's social security number is a unique nine-digit number that the United States government assigns to each citizen for the purpose of tracking their earnings and monitoring social security benefits. It is also used as a form of identification and is frequently required when applying for employment, opening a bank account, and obtaining credit.

Why was the patient social security number not chosen to be the key field of that table?

The patient social security number was not chosen to be the key field of the patient table because it is personal information. Because social security numbers are confidential, using them as keys would pose a significant security risk if a hacker were to access the database. Furthermore, utilizing personal identification numbers as primary keys could be perceived as an invasion of privacy.

When the sports physical therapy database was created, the patient social security number was not chosen as the key field for the patient table despite being a candidate key because it might have privacy and security concerns. Using a patient social security number as a primary key could expose sensitive personal information and increase the risk of identity theft. Instead, the patient num, which is unique and anonymous, was chosen as a more secure and privacy-preserving option for the primary key.

Learn more about social security number

https://brainly.com/question/19590631

#SPJ11

Network congestion is a circumstance in which a network connection slows or fails because the network can't handle the amount of traffic or data being transmitted at the time.

When comparing the two events, receiving triple duplicate acknowledgement and timeout, the one that indicates the network congestion level is more serious is receiving triple duplicate acknowledgement. There are a variety of explanations for network congestion, and there are a variety of ways to address it. Acknowledgement Triple Duplicate When a packet is transmitted, it is generally acknowledged by the recipient. When the sender fails to obtain an acknowledgement after a certain amount of time has elapsed, a timeout occurs. When the receiving end receives three of the same acknowledgement messages, it is referred to as receiving triple duplicate acknowledgement. In a congested network, receiving triple duplicate acknowledgement is more likely to occur than timeout. When the network congestion level is more severe, packets take longer to reach their intended destination, causing multiple duplicate acknowledgements to be generated. As a result, receiving triple duplicate acknowledgements indicates a more serious network congestion level.

Learn more about Network congestion here:

https://brainly.com/question/4658841

#SOJ11

The constraints that its parent places upon it primarily determine the position and size of a particular widget in Flutter.

In Flutter, the position and size of a particular widget are primarily determined by the constraints that its parent places upon it. Each widget in Flutter has its own constraints, which specify the minimum and maximum sizes that the widget can occupy on the screen. These constraints are then passed up the widget tree to the parent widget, which can further constrain the size and position of its children. The constraints are used to determine the layout of the widgets in the user interface and are an essential part of Flutter's reactive programming model. The theme data of the parent widget and the pixel density of the device screen can affect the appearance of the widget but do not directly determine its size or position. The BuildContext is used to identify the location of the widget in the widget tree but does not directly affect its layout.

learn more about widget

brainly.com/question/30887492

#SPJ4

The correct answer choices are "the binary tree must be complete" and "the value stored at every node is less than or equal to the values stored at either of its child nodes (min heap)."

For a binary tree to be considered a heap, the following conditions must be imposed:

1. The binary tree must be complete, meaning that every level of the tree is fully filled, except possibly for the last level, which should be filled from left to right.

2. The value stored at every node is either less than or equal to the values stored at its child nodes (min heap) or greater than or equal to the values stored at its child nodes (max heap).

You can learn more about binary trees at: brainly.com/question/13152677

#SPJ11

True. Indeed, corporations build honey pots as a ruse to stave off hackers drawn to a particular computer system.

Organizations employ honey pots as a security measure to trick hackers into attacking a computer system while guarding the actual system from intrusion attempts. Honey pots are created to mimic vulnerable systems or services, drawing attackers in and allowing security experts to analyse their behaviour and tactics without exposing critical data or systems. Honey pots can also act as early warning devices, informing security staff of possible dangers before they can do any harm. Honey pots can be a useful part of a thorough security plan, but they are not completely reliable and shouldn't be used as the only form of defence.

learn more about computer system here:

https://brainly.com/question/30146762

#SPJ4

The problem with connecting two old routers together with a UTP cable and not being able to send and receive data between them could be due to incorrect cable type or router configuration issues.

To fix this issue, follow these steps:

1. Ensure that you are using the correct cable type: When connecting two routers directly, you should use a crossover Ethernet cable instead of a straight-through cable. Crossover cables have their send and receive pins reversed, which allows data to be transmitted and received between devices of the same type, such as routers.

2. Check the router configuration: Ensure both routers are configured to operate in the appropriate mode for your network. This could involve setting one router as the main router (providing DHCP services) and the other as an access point or switch (with DHCP disabled). Also, make sure that both routers have unique IP addresses to avoid conflicts.

3. Verify the network settings: Check that the routers are using the same subnet and have compatible IP address ranges. For example, if one router's IP address is 192.168.1.1, the other router should have an IP address within the 192.168.1.X range, but not the same as the first router.

4. Test the cable and routers: If possible, test the UTP cable with other devices to ensure that it is functioning properly. Additionally, try connecting the routers to other devices to ensure they are not the source of the problem.

By following these steps, you should be able to identify and resolve the issue preventing successful data transmission and reception between the two routers connected with a UTP cable.

You can learn more about UTP cable at: brainly.com/question/13362491

#SPJ11

Convert total dollars For an input of 58 dollars, the output is 1 fifty-dollar bill, 1 five-dollar bill, and 3 one-dollar bills.

To convert the total dollars to 50-dollar bills, 5-dollar bills, and one-dollar bills, finding the maximum number of 50-dollar bills, then 5-dollar bills, and finally one-dollar bills, follow these steps:

1. Divide the total amount by 50 to find the maximum number of 50-dollar bills. For example, if the input is 58 dollars, divide 58 by 50: 58 / 50 = 1 (with a remainder of 8).

2. Next, take the remainder from the previous step and divide it by 5 to find the maximum number of 5-dollar bills. Using the remainder of 8 from step 1, divide 8 by 5: 8 / 5 = 1 (with a remainder of 3).

3. Finally, the remaining amount is the maximum number of one-dollar bills. In this example, the remainder is 3, so there are 3 one-dollar bills.

So, for an input of 58 dollars, the output is 1 fifty-dollar bill, 1 five-dollar bill, and 3 one-dollar bills.

Learn more about Convert: brainly.com/question/29414508

#SPJ11

Here's an example MIPS assembly program that implements linear search to find a number entered by the user in an array of 20 integers:

.data

array:  .word   4, 5, 8, 9, 1, 3, 10, 7, 6, 15, 20, 11, 14, 12, 16, 19, 2, 18, 17, 13

message1: .asciiz "Enter a number to search for: "

message2: .asciiz "The number was found at index "

message3: .asciiz "The number was not found."

.text

.globl main

# procedure to search for a number in an array

# arguments: $a0 - pointer to the array

#            $a1 - size of the array

#            $a2 - number to search for

# returns:   $v0 - index of the number in the array, or -1 if not found

linear_search:

   addi $sp, $sp, -8     # allocate space on the stack

   sw   $ra, 0($sp)      # save the return address

   li   $t0, 0           # initialize index to 0

loop:

   beq  $t0, $a1, not_found   # if index == size, return -1

   lw   $t1, ($a0)        # load the array element at index i

   beq  $t1, $a2, found       # if element == number, return i

   addi $t0, $t0, 1      # increment index

   addi $a0, $a0, 4      # advance array pointer

   j    loop

found:

   move $v0, $t0         # set the return value to the index

   j    done

not_found:

   li   $v0, -1          # set the return value to -1

done:

   lw   $ra, 0($sp)      # restore the return address

   addi $sp, $sp, 8      # deallocate space on the stack

   jr   $ra              # return to the caller

# main program

main:

   li   $v0, 4           # print message asking for input

   la   $a0, message1

   syscall

   li   $v0, 5           # read in the number to search for

   syscall

   move $a2, $v0         # store the number to search for in $a2

   la   $a0, array       # set array pointer in $a0

   li   $a1, 20          # set array size in $a1

   jal  linear_search    # call linear search procedure

   beq  $v0, -1, not_found   # if return value is -1, print not found message

   li   $v0, 4           # print found message

   la   $a0, message2

   syscall

   move $a0, $v0         # print the index of the number

   li   $v0, 1

   syscall

   j    done

not_found:

   li   $v0, 4           # print not found message

   la   $a0, message3

   syscall

done:

   li   $v0, 10          # exit program

   syscall

Note that this program initializes the array with

When you use the animate() method, you must code a properties map, a duration parameter, and optionally, a callback function and CSS properties to define the animation.

Here's a step-by-step explanation:

1. Create a properties map: This is an object that contains CSS properties and their target values, which define how the elements will be animated.

2. Set a duration parameter: This is a numerical value representing the duration of the animation in milliseconds or a string representing a predefined duration (e.g., "slow", "fast").

3. (Optional) Add a callback function: This function will be executed once the animation is completed.

4. (Optional) Include CSS properties: You can use CSS properties within the properties map to further define the animation's appearance and behavior.

Here's an example of using the animate() method:

```javascript
$("element").animate({
   opacity: 0.5,
   left: "+=50"
}, 1000, function() {
   // This callback function will be executed after the animation is completed
   console.log("Animation completed!");
});
```

In this example, the element will change its opacity to 0.5 and move 50 pixels to the right over 1000 milliseconds. After the animation is completed, the callback function will log "Animation completed!" in the console.

You can learn more about CSS property at: brainly.com/question/7686121

#SPJ11

An IP address is a distinctive series of numbers, each separated by a period, that uniquely identifies every machine communicating over a network using the Internet Protocol.

To learn more about Internet Protocol, refer to:

https://brainly.com/question/17820678

Selection sort is an algorithm that works by iteratively selecting the smallest element from the unsorted part of an array and swapping it with the element at the beginning of the unsorted section. This process is repeated for each index, with the sorted section growing by one element each time.

1)Initially, the whole array is considered unsorted. The algorithm starts at the first index, searches for the minimum value among the unsorted elements, and then swaps that minimum value with the value at the first index. Now, the first element is sorted, and the unsorted section starts from the second index.

2)The algorithm continues by finding the minimum value in the remaining unsorted section, starting from the second index. Once found, this minimum value is swapped with the value at the second index. Now, the first two elements are sorted, and the unsorted section starts from the third index.

3)This process is repeated for each index until the entire array is sorted. By iteratively selecting the smallest element from the unsorted part and swapping it with the current index, selection sort efficiently sorts the array in ascending order.

4)In summary, selection sort works by dividing the array into a sorted and an unsorted section. It iteratively finds the smallest element in the unsorted section and swaps it with the first unsorted element, effectively expanding the sorted section and reducing the unsorted section until the whole array is sorted.

For more such question on algorithm

https://brainly.com/question/13902805

#SPJ11

The total number of available IP addresses in a /26 subnet is 64 IP addresses. Excluding 12 IP addresses for network devices, the remaining 52 IP addresses are available for DHCP client assignment.

When you configure a router as a DHCP server and make a pool with the range 172.16.31.0 /26. The total number of available IP addresses in a /26 subnet is 64 IP addresses. 12 IP addresses are reserved for network devices. As a result, the remaining number of IP addresses that can be leased out to clients is 52.To clarify, a /26 subnet contains 64 IP addresses. The first three octets of the IP address in the given subnet, 172.16.31.0/26, are fixed, and the last octet has a 26-bit mask, allowing for 6 host bits. This equals 64 IP addresses. Excluding 12 IP addresses for network devices, the remaining 52 IP addresses are available for DHCP client assignment.

Learn more about DHCP here:

https://brainly.com/question/15308834

#SPJ11

To create a CSS class myfloat that floats to the right of the other page content and has a 10px margin, you can use the following code: ```.myfloat {  float: right; margin: 10px; border: 1px solid black; }``

`In the above code, `.myfloat` is the name of the CSS class. `float: right` makes the content float to the right side of the page. `margin: 10px` sets a 10-pixel margin around the content. `border: 1px solid black` creates a solid 1-pixel black border around the content.

By using the above code, you can create a class according to your requirement.

You can learn more about CSS at: brainly.com/question/14152823

#SPJ11

The most likely reason that Pavel, an IT project lead at Krystal Engineering, is not able to open the file Plstatus.xls is due to the permissions set for the different groups he is a part of.

Although Pavel's user account has full control permission over the file, he is also a member of the developer group and the project manager group, which have different access levels.

The project manager group has modify access, but not full control. This means that they can edit the file but not perform some advanced actions, like changing permissions. However, the developer group has write access but no read access. Since Pavel is part of this group, this restriction takes precedence and prevents him from opening the file.

To resolve this issue, you should consider granting the developer group read access to the file. This will allow Pavel to open the file, as the combined permissions from his user account and the groups he belongs to will provide the necessary access to perform the required tasks.

To Learn More About Plstatus

https://brainly.com/question/31319011

#SPJ11

Considering a target value and input value, the loss is 0.029.

A simple 2-layer neural network with a single neuron in each layer is being considered. The loss function is the quadratic loss, where is the prediction and is the target. Starting with the input we have:

consider a target value and input value. The weights and biases are, and. The numerical answers should be accurate to at least three decimal places. Loss is the difference between the predicted and actual output. Mathematically, it is represented as a quadratic loss or mean square error, which is the difference between the predicted output and the actual output, squared.

Loss=(prediction−target)2

Loss = (0.7278 − 0.9)2= 0.0292

You can learn more about neural networks at: brainly.com/question/14632443

#SPJ11

Systems design is a crucial aspect of the development process, as it outlines the functional and operational requirements of a system to meet the specified information needs. This process typically involves a group of answer choices that address different aspects of the system, including its purpose, functionality, and overall design.

1)One of the primary objectives of systems design is to determine what a system should do to meet its information requirements. This entails understanding the necessary inputs, processes, and outputs that the system must manage to satisfy the needs of its users.

2)Another aspect of systems design involves showing how the new system will fulfill these information requirements. This is achieved by creating detailed design specifications, such as data flow diagrams or flowcharts, that illustrate how information will be processed and managed within the system.

3)Systems design also identifies which users need what information, where, when, and how. This is essential for ensuring that the system provides the right information to the right people at the right time and in the appropriate format. This often involves gathering user requirements and developing use cases to ensure that the system meets the diverse needs of its intended users.

4)Lastly, systems design is concerned with the logical view of the system solution. This involves focusing on the relationships between the different components of the system, as well as how data is processed, stored, and accessed. By considering the logical view, designers can create a more efficient and effective system that meets its intended purpose.

5)In summary, systems design is a vital process in the development of any system, as it outlines the functional and operational requirements necessary to meet the specified information needs. This process involves determining what the system should do, how it will fulfill these requirements, identifying user needs, and focusing on the logical view of the system solution.

For such more question components

https://brainly.com/question/28351472

#SPJ11

Two rotations would be required to balance an AVL tree in the case where the right child is taller than the left child by more than 1, and the right child is heavy on the left side.

Two rotations would be required to balance an AVL tree if the right child is taller than the left child by more than 1 and the right child is heavy on the left side. What is an AVL tree? An AVL tree is a self-balancing binary search tree in which the difference between the heights of its left and right subtrees can be at most 1. The purpose of balancing is to reduce the search time of a node. AVL trees require fewer rotations while inserting and deleting nodes compared to red-black trees. What is tree rotation? A "tree rotation" is an operation that changes the structure of a binary tree without changing the order of the nodes in the tree. Tree rotations maintain the binary search tree's property of being sorted. In an AVL tree, rotation operations are carried out whenever the balance factor of a node is either +2 or -2. When the balance factor is +2, the tree is heavier on the left side, and when the balance factor is -2, the tree is heavier on the right side.
Visit here to learn more about AVL tree :

https://brainly.com/question/12946457

#SPJ11

HTML document to create a form that collects favorite popular songs:Below is the HTML code to create a form that collects favorite popular songs, including the name of the song, the composer and the performing artist or group. This form must call one PHP script (that you will write in question 2) when the form is submitted.

The HTML document you are writing in question 1 will also have a link to another PHP script (that you will write in question 3) that will display a list of survey results.  ``Note: In the above code, the action attribute of the form is set to "survey.php"  the name of the PHP script that you will write in  2. The link to the PHP script that will display a list of survey results is included at the end of the form using the anchor tag.

Learn more about HTML   here:

https://brainly.com/question/17959015

#SPJ11

Location-based networking provides a platform for users to carry out interactions based on their current locations. Location-based networking is a type of networking that allows users to interact with each other based on their current locations.

It is a feature that is present in many social networking and messaging applications, allowing users to find and connect with others who are nearby. In location-based networking, users can find and communicate with other people who are nearby.

This can be useful for social networking, dating, and other applications that require location-based information. Location-based networking can be used to find people who share similar interests, businesses, and services in the area, and events that are happening nearby.

These apps use the location data provided by the user's device to show them nearby people or places that they may be interested in. Location-based networking has become more popular in recent years due to the widespread adoption of smartphones and other mobile devices that can easily transmit location data.
Geolocation-based networking provides a platform for users to carry out interactions based on their current locations.

Learn more about Location-based networking

https://brainly.com/question/29767929

#SPJ11

When a group or user group policy setting is in the scope of a GPO, it is managed by the GPO. If the scope is changed to its original configuration outside the GPO, it is called the local scope.

Group Policy Objects (GPOs) are a Microsoft Windows NT-based operating system component that administers the security and operating system settings for users and computers in an organization.The GPO can be divided into two distinct components: the Group Policy Container (GPC) and the Group Policy Template (GPT).The GPC keeps track of the GPO name, domain name, version number, unique identifier, and information about where to locate the GPT. On the other hand, the GPT contains all of the data and information that the GPO contains, such as registry entries, script files, and text files.User Group Policy SettingsThe User Configuration node contains the majority of the GPO's user settings. The user settings' scope may be limited to a single site, domain, or OU. There are several subcategories in User Configuration that specify different configurations for users. Some of these settings are:Desktop: This policy deals with the settings that pertain to the appearance and configuration of the desktop.Backgrounds: It deals with the settings that define the desktop background and its appearance.Start Menu and Taskbar: This policy deals with the Start menu, Quick Launch, and Taskbar features.

Learn more about GPO here:

https://brainly.com/question/31066652

#SPJ11

Answer:

Explanation:

i+=i means the i now adds its current value to its self so let's say i equals 10 using this += expression the value of i will now equal 20 because you just added 10 to its self.

Answer:

a) Presentation Software