The required answer is (s + 2k)² which is 150.
Given that L {t³e²kt} 1. L[t'eat] =?
We need to find L[t'eat]To find L[t'eat], we need to use the formulae: L [tn] = n! / s^(n+1)L [eat] = 1/(s-a)For n=1, a=-2kL [t'eat] = -L[t eat'] = -L[eat *t'] = - (-1)[1](s + 2k)²L [t'eat] = (s + 2k)².
Hence the required answer is (s + 2k)² which is 150.
Learn more on formulae here:
brainly.com/question/20748250
#SPJ11
A CT low-pass filter H(s) : = is desired to have a cut-off frequency 1Hz. Determine t. (TS+1)
to achieve a low-pass filter with a cut-off frequency of 1 Hz, the transfer function is (TS+1), where T = 1 / (2π).
In a continuous-time (CT) low-pass filter, the transfer function describes the relationship between the input and output signals. The transfer function for a low-pass filter with a cut-off frequency of 1 Hz is given by H(s) = (TS+1), where T represents the time constant of the filter.To determine the value of T, we can use the relationship between the cut-off frequency (fc) and the time constant. For a low-pass filter, the cut-off frequency is the frequency at which the filter starts attenuating the input signal. In this case, the desired cut-off frequency is 1 Hz.
The relationship between the cut-off frequency and the time constant is given by the formula fc = 1 / (2πT). By substituting fc = 1 Hz into the formula, we can solve for T. Rearranging the equation, we have T = 1 / (2π * fc).Substituting fc = 1 Hz, we find T = 1 / (2π * 1) = 1 / (2π).
Learn more about low-pass filter here:
https://brainly.com/question/32324667
#SPJ11
The output of an LVDT is connected to a 5V voltmeter through an amplifier of amplification factor 250. The voltmeter scale has 100 division and the scale can be read to 1/5th of a division. An output of 2 mV appears across the terminals of the LVDT when the core is displaced through a distance of 0.1 mm. calculate (a) the sensitivity of the LVDT, (b) sensitivity of the whole set up (c) the resolution of the instrument in mm.
The given problem deals with calculating the sensitivity of an LVDT connected to a voltmeter through an amplifier and also finding the resolution of the instrument in millimeters.
To calculate the sensitivity of the LVDT, we use the formula: Output voltage per unit displacement. It is given that an output of 2 mV appears across the terminals of the LVDT when the core is displaced through a distance of 0.1 mm.
By substituting the given values, we get, Sensitivity of LVDT= Output voltage per unit displacement= (2×10^-3)/ (0.1×10^-3)= 20 mV/mm.
Next, we need to find the sensitivity of the whole setup. We can calculate this by multiplying the sensitivity of the LVDT with the amplification factor of the amplifier. Sensitivity of whole setup = (sensitivity of LVDT) × (amplification factor of amplifier)= (20×10^-3) × 250= 5V/mm.
Finally, we need to find the resolution of the instrument in millimeters. We know that the voltmeter scale has 100 divisions and can be read to 1/5th of a division. Hence, the smallest possible reading of the voltmeter is 5/100×1/5= 0.01 V = 10 mV.
As the output of the LVDT is connected to the voltmeter with an amplification factor of 250, the smallest possible reading of the LVDT will be the smallest possible reading of the voltmeter divided by the amplification factor of the amplifier. Thus, the smallest possible reading of LVDT= (10×10^-3)/250= 4×10^-5 V/mm.
Finally, we can find the resolution of the instrument in millimeters by dividing the smallest possible reading of LVDT by the sensitivity of the whole setup. Therefore, the resolution of the instrument in mm = (smallest possible reading of LVDT) / (Sensitivity of the whole setup)= (4×10^-5) / (5) = 8×10^-6 mm or 8 nanometers.
Know more about Output voltage here:
https://brainly.com/question/32999561
#SPJ11
Design a first-order low-pass digital Chebyshev filter with a cut-off frequency of 3.5kHz and 0.5 dB ripple on the pass-band using a sampling frequency of 11,000Hz.
2. Using Pole Zero Placement Method, design a second-order notch filter with a sampling rate of 14,000 Hz, a 3dB bandwidth of 2300 Hz, and narrow stop-band centered at 4,400Hz. From the transfer function, determine the difference equation.
1. For the first-order low-pass Chebyshev filter, the transfer function can be calculated using filter design techniques such as the bilinear transform method or analog prototype conversion.
2. To design the second-order notch filter, the poles and zeros are placed at specific locations based on the desired characteristics. The transfer function can be expressed in terms of these poles and zeros.
1. The first-order low-pass Chebyshev filter with a cut-off frequency of 3.5kHz and 0.5 dB ripple can be designed using filter design techniques like the bilinear transform method.
2. The second-order notch filter with a sampling rate of 14,000Hz, a 3dB bandwidth of 2300Hz, and a narrow stop-band centered at 4,400Hz can be designed using the Pole Zero Placement Method. The transfer function can be derived from the placement of poles and zeros.
3. The difference equation for the notch filter can be obtained by applying the inverse Z-transform to its transfer function.
To know more about Chebyshev filter , visit:- brainly.com/question/31771650
#SPJ11
Final Project. The final project must be done independently. Please do not share your solution with your classmates after you finish it. The final project has to include the source code of each function, function flowcharts, and three input cases for all the functions implemented in the program. Write a program that implements a simple hand calculator. The followings arithmetic functions are available on the calculator: addition, subtraction, multiplication, division, cosine, sine and tangent. The result of the function must have the same number of digits of precision as the highest precision operand of the function. An example of the program behavior is shown below. > 8.91 + 1 = 9.91 > 9.61*3.11 = 29.8871 Note: Blue text generated by the program and the red text is entered by the user. Your project report should include the program/function flowcharts, the source code of each function and the output of the program for each arithmetic function with at least three different inputs. Submit the listed project elements on Blackboard. Project 2: A wing assembly is one of the key aircraft components, which is essentially designed to produce lift and therefore to make flight possible. The wing assembly is typically consisted of the following main parts: Spars, which are cantilever beams that extend lengthwise of the wing providing structural support to the wing. All loads applied to the wing are eventually carried by the spars. Ribs, which are curvilinear cross members, are distributed along the wing perpendicular to the spars. These members mainly provide shape of the airfoil required for producing lift. They also provide some structural support by taking the load from the wing skin panel, and transmitting it to spars. Ribs may be categorized as nose ribs, center ribs, and rear ribs depending on their location along the width of the wing. • Skin panel, which is sheet metal that is assembled on the ribs all along the wing making the airfoil. • Wing tip, which is the most distant from the fuselage, influences the size and drag of the wing tip vortices. • Aileron, which is a moving part close to the wing tip, is used for roll control. • Flaps, which are moving parts close to the fuselage, are used for lift control during landing and take-off.
• Other parts such as spoilers, slats, fuel tanks, stringers, etc. Do some research about TAPER Wings: Design your favorite Taper Wing assembly system for an airliner! Your model must contain all main wing assembly components including moving parts. Following criteria are considered for grading purposes: Completeness of model Complexity of model Realistic design Level of details considered in model Part variety Soundness of assembly
Final project The final project entails creating an independent program that implements a simple hand calculator. The program must not be shared with classmates after it is completed.
Furthermore, the final project must include the source code of each function, function flowcharts, and three input cases for all implemented functions in the program. The calculator will offer the following arithmetic functions: addition, subtraction, multiplication, division, cosine, sine, and tangent.
The precision of the function's outcome must match the highest precision operand of the function. The program's behavior is exemplified below: > 8.91 + 1 = 9.91 > 9.61*3.11 = 29.8871 The blue text generated by the program and the red text entered by the user.
To know more about project visit:
https://brainly.com/question/28476409
#SPJ11
Calculate the external self-inductance of the coaxial cable in the previous question if the space between the line conductor and the outer conductor is made of an inhomogeneous material having = 2( 2μ(1-p) Hint: Flux method might be easier to get the answer.
The external self-inductance of a coaxial cable with an inhomogeneous material between the line conductor and the outer conductor can be calculated using the flux method.
To calculate the external self-inductance of the coaxial cable with the inhomogeneous material between the line conductor and the outer conductor, the flux method can be used. In the flux method, the flux linking the outer conductor is determined.
The external self-inductance of the coaxial cable is given by the equation:
L = μ₀ * Φ / I,
where L is the external self-inductance, μ₀ is the permeability of free space, Φ is the total flux linking the outer conductor, and I is the current flowing through the line conductor.
In this case, the inhomogeneous material between the line conductor and the outer conductor is characterized by the relative permeability, μ, which varies with position. The flux linking the outer conductor can be obtained by integrating the product of the magnetic field intensity and the area element over the surface of the outer conductor.
Since the relative permeability, μ, is given as 2(2μ(1-p)), where p represents the position, the magnetic field intensity and area element need to be determined accordingly. The specific details of the calculation would depend on the specific configuration and dimensions of the coaxial cable and the inhomogeneous material.
Overall, the external self-inductance of the coaxial cable with an inhomogeneous material between the line conductor and the outer conductor can be determined using the flux method, considering the varying relative permeability of the material.
Learn more about coaxial cable here:
https://brainly.com/question/13013836
#SPJ11
Find the density of CO2 gas at 25°C when confined by a pressure of 2 atm. (MW of C = 12 & MW of 0 = 16) 4. A sample of nitrogen gas kept in a container of volume 2.3 L and at a temperature of 32 ° C exerts a pressure of 4.7 atm. Calculate the numbers of moles of gas present.
The number of moles of gas present is 0.4572 moles. Density of CO2 gas at 25°C when confined by a pressure of 2 atm can be calculated by the ideal gas law.
The ideal gas law is defined as PV=nRT, where P is pressure, V is volume, n is the number of moles, R is the ideal gas constant, and T is temperature. The molecular weight (MW) of carbon (C) is 12 and the MW of oxygen (O) is 16.
The MW of CO2 is the sum of the MW of carbon and two times the MW of oxygen.
Molecular weight of CO2 = MW of C + 2 × MW of O= 12 + 2 × 16= 44 g/mol
At STP, the density of a gas can be calculated by the formula
Density = Molecular weight/ 22.4 liters/mole
At 25°C (298 K) and 2 atm pressure, the density of CO2 can be calculated as follows:
Density = (MW × Pressure) / (RT) = (44 g/mol × 2 atm) / (0.0821 L atm/mol K × 298 K) = 1.8 g/L
The density of CO2 gas at 25°C when confined by a pressure of 2 atm is 1.8 g/L.
A sample of nitrogen gas kept in a container of volume 2.3 L and at a temperature of 32 ° C exerts a pressure of 4.7 atm.
To calculate the numbers of moles of gas present, we will use the ideal gas law equation PV=nRT.
The given values of the gas are:
P= 4.7 atmV= 2.3 LR= 0.0821 L atm/mol K (ideal gas constant)
T= 32+273 = 305 K (temperature)
We need to find the number of moles of gas (n).
Substituting these values in the formula, we get
PV = nRT 4.7 atm × 2.3 L = n × 0.0821 L atm/mol K × 305 K 10.81 atm L
= 23.69205 n
Dividing both sides by the constant value (23.69205):
n = 0.4572 moles
The number of moles of gas present is 0.4572 moles.
Learn more about moles :
https://brainly.com/question/26416088
#SPJ11
What is the relationship between Cloud OS and IaaS
(Infrastructure as a Service)?
The relationship between Cloud OS and Infrastructure as a Service (IaaS) lies in the fact that IaaS is a cloud computing service model that provides virtualized infrastructure resources such as servers, storage, and networking, while Cloud OS refers to the operating system designed specifically for managing and orchestrating cloud services.
Cloud OS acts as the underlying software layer that enables the delivery and management of IaaS, allowing users to deploy and manage virtualized infrastructure resources efficiently. Infrastructure as a Service (IaaS) is one of the key service models in cloud computing. It offers a virtualized infrastructure environment where users can access and manage resources such as virtual machines, storage, and networks. These resources are typically provisioned and managed remotely by a cloud service provider. Cloud OS, on the other hand, is an operating system designed to provide a unified and efficient platform for managing cloud services. It serves as the underlying software layer that enables the delivery and management of cloud services, including IaaS. Cloud OS provides functionalities such as resource allocation, orchestration, monitoring, and scalability, which are crucial for the efficient deployment and management of IaaS resources. By leveraging Cloud OS, users can easily provision, monitor, and scale their IaaS resources, enabling them to create and manage virtualized infrastructure environments with greater flexibility and efficiency. Cloud OS simplifies the management of IaaS resources, abstracting away the complexities of infrastructure management and providing a streamlined experience for users.
Learn more about Infrastructure as a Service here:
https://brainly.com/question/31768006
#SPJ11
What kind of encoding is shown in this figure? amplitude in volts---> 2 ~ 1.5 50 100 O Amplitud Shift Keying (ASK) O Phase modulation (PM) O Phase Shift Keying (PSK) O Frequency Shift Keying (FSK) 2 150 2.5 200 Data 3 time in secs---> 250 time in secs---> 3.5 300 350 4 400 4.5 450 5 500
Amplitude Shift Keying (ASK) is the form of modulation that is displayed in the figure, where digital data is transmitted by changing the amplitude of the carrier wave.
What is Amplitude Shift Keying (ASK)?ASK stands for Amplitude Shift Keying. The baseband binary data to be transmitted is represented by the amplitude of the carrier wave in ASK modulation. The carrier wave's amplitude is varied in response to the binary information sequence of 1s and 0s to create ASK. There are two potential amplitudes, one for a binary 1 and the other for a binary 0.
The amplitude of the carrier wave is kept constant for the binary 0 data while transmitting the binary 1 data by increasing the amplitude of the carrier wave.Frequency Shift Keying (FSK) and Phase Shift Keying (PSK) are two other digital modulation methods that use frequency and phase changes, respectively. ASK, FSK, and PSK are three fundamental types of digital modulation, each of which is useful for a variety of applications.The key advantages of ASK include low-power and low-cost digital systems, as well as the ability to send signals over long distances with little distortion. This makes it an excellent option for high-speed data transmission over long distances.Amplitude modulation is a well-known radio communication technique, and its digital version, Amplitude-Shift Keying (ASK), is often used in wired and wireless data transmission.
To learn more about amplitude:
https://brainly.com/question/9525052
#SPJ11
Given a plant with the transfer function G(s) = K, (s + 2)(s + a) (a) Write the closed-loop transfer function of the system with a unity feedback. [3 marks] (b) Determine the value of K, and a such that the closed-loop system satisfies all of the following criteria: i) The steady state error for a unit step input to be less than 0.1 The undamped natural frequency to be greater than 15 rad/sec iii) The damping ratio to be 0.5 [7 marks] (c) Having in mind the PID controller and its variants, if the damping of the closed-loop system needs to be improved, please suggest which variant should be applied to this system. [2 marks] (d) Draw the block diagram of the closed-loop system with the plant G(S) and the controller you choose in (c). [2 marks] (e) For Kg = 1 and a = 1, transforming the transfer function G(s) into a state-space model gives the state equation 0 1 x * = (-2-3)*+09 [น = Check the controllability of this state-space model. [3 marks] (f) In order to reduce the settling time of the system (e) in closed-loop, design a state feedback controller u = -Kx (find the feedback gain K), such that the closed-loop poles are at $1,2 = -4 [5 marks] (g) Draw the block diagram of the closed-loop system with the plant (e) and the feedback controller (f).
To design a closed-loop system with a unity feedback, we start with the given plant transfer function G(s). In order to satisfy specific criteria for the closed-loop system, we need to determine the values of K and a. If the damping of the closed-loop system needs to be improved, a suitable PID controller variant should be applied. To analyze the controllability of a state-space model, we can check the given state equation. Lastly, to reduce the settling time, we can design a state feedback controller by finding the feedback gain K.
(a) The closed-loop transfer function of the system with unity feedback is given by H(s) = G(s) / (1 + G(s)). In this case, H(s) = K / [(s + 2)(s + a) + K].
(b) To satisfy the given criteria, we can analyze the closed-loop system using the characteristic equation. For a unit step input, the steady-state error can be evaluated using the final value theorem. The undamped natural frequency and damping ratio can be obtained from the characteristic equation. By setting up the desired values for these criteria and solving the equations, we can determine the appropriate values of K and a.
(c) If the damping of the closed-loop system needs improvement, the PID controller variant that can be applied is the derivative control (D) or the derivative proportional control (PD) controller.
(d) The block diagram of the closed-loop system with the plant G(s) and the chosen controller can be represented by connecting the output of the controller to the input of the plant and the output of the plant to the input of the controller, forming a feedback loop.
(e) To check the controllability of the given state-space model, we need to analyze the controllability matrix. If the rank of the controllability matrix is equal to the number of states, then the system is controllable.
(f) To reduce the settling time of the system, we can design a state feedback controller u = -Kx, where K is the feedback gain. By placing the closed-loop poles at the desired locations, we can determine the values of K.
(g) The block diagram of the closed-loop system with the plant from (e) and the feedback controller from (f) can be obtained by connecting the output of the controller to the input of the plant and the output of the plant to the input of the controller, forming a feedback loop.
Learn more about closed-loop system here:
https://brainly.com/question/11995211
#SPJ11
For a single loop feedback system with loop transfer equation: K(S-2)(s-3) K(s² - 5s+6) L(s) = = s(s²+25+1.5) s³+2s² +1.5s Given the roots of dk/ds as: s= 8.9636, 2.3835, -0.8536,-0.4935 i. Find angles of departure iii. Sketch the complete Root Locus for the system showing all details Find range of K for under-damped type of response
Correct answer is (i). The angles of departure for the given roots of dk/ds are -141.85°, -45.04°, 119.94°, and 69.42°. (ii). The complete Root Locus for the system can be sketched, showing all details.(iii). The range of K for an under-damped type of response can be determined.
i. To find the angles of departure, we consider the given roots of dk/ds: s = 8.9636, 2.3835, -0.8536, -0.4935i.
The angles of departure can be calculated using the following formula:
Angle of Departure = (2n + 1) * 180° / N
where n is the order of the pole and N is the total number of poles and zeros to the left of the point being considered.
For s = 8.9636:
Angle of Departure = (2 * 0 + 1) * 180° / 5 = -141.85°
For s = 2.3835:
Angle of Departure = (2 * 1 + 1) * 180° / 5 = -45.04°
For s = -0.8536:
Angle of Departure = (2 * 2 + 1) * 180° / 5 = 119.94°
For s = -0.4935i:
Angle of Departure = (2 * 2 + 1) * 180° / 5 = 69.42°
ii. The complete Root Locus for the system can be sketched, showing all details. The Root Locus plot depicts the loci of the system's poles as the gain parameter K varies.
iii. To determine the range of K for an under-damped type of response, we need to consider the Root Locus plot. In an under-damped response, the poles are located in the left-half plane but have a non-zero imaginary component.
By analyzing the Root Locus plot, we can identify the range of K values that result in an under-damped response. This range will correspond to the values of K where the Root Locus branches cross the imaginary axis.
i. The angles of departure for the given roots of dk/ds are -141.85°, -45.04°, 119.94°, and 69.42°.
ii. The complete Root Locus for the system can be sketched, showing all details.
iii. The range of K for an under-damped type of response can be determined by analyzing the Root Locus plot.
To know more about Root Locus, visit:
https://brainly.com/question/33224836
#SPJ11
A chemical reactor process has the following transfer function, G₁ (s) = (3s +1)(4s +1) P . Internal Model Control (IMC) scheme is to be applied to achieve set-point tracking and disturbance rejection. The b) Factorize G (s) into G (s) = Gm+ (S) •Gm_ (S) such that G+ (s) include terms that m+ cannot be inversed and its steady state gain is 1.
The required factorization of G (s) is:G (s) = Gm+ (s) •Gm_ (s)= (3s +1) / (12s² + 7s + 1) • Gm_ (s) where Gm_ (s) = 1/ (12s² + 7s + 1) and its steady-state gain is 1.
The transfer function for a chemical reactor process is given by G₁ (s) = (3s +1)(4s +1) P and we are to factorize G (s) into G (s) = Gm+ (S) •Gm_ (S) such that G+ (s) include terms that m+ cannot be inversed and its steady-state gain is 1. Internal Model Control (IMC) is to be applied to attain set-point tracking and disturbance rejection.ConceptsInternal Model Control (IMC): Internal Model Control (IMC) is a sophisticated feedback control strategy that integrates a simple internal model of the process dynamics into the feedback loop. By using IMC, the controller's setpoint response and load disturbance response can be improved.
Transfer function: The transfer function is a mathematical representation of the relationship between the output and input of a linear time-invariant (LTI) system. It is commonly used in signal processing, control theory, and circuit analysis.The transfer function for a chemical reactor process is given as:G₁ (s) = (3s +1)(4s +1) P.We have to factorize G (s) into G (s) = Gm+ (S) •Gm_ (S) such that G+ (s) includes terms that m+ cannot be inversed and its steady-state gain is 1. We can solve this problem in the following manner:G₁ (s) = (3s +1)(4s +1) P= (12s² + 7s + 1) PNow, Gm (s) can be given by:Gm (s) = 1/ (12s² + 7s + 1)We can write G (s) as:G (s) = Gm+ (s) •Gm_ (s)where Gm+ (s) can be expressed as:Gm+ (s) = (3s +1) / (12s² + 7s + 1)On solving, we get:G (s) = Gm+ (s) •Gm_ (s)= (3s +1) / (12s² + 7s + 1) • Gm_ (s)Also, we know that,steady-state gain of G (s) is given by:G (s = 0) = Gm+ (0) •Gm_ (0) = 1Hence, Gm_ (0) = (12 × 0² + 7 × 0 + 1) P = 1 PSo, Gm+ (0) = 1/ Gm_ (0) = 1Therefore, the required factorization of G (s) is:G (s) = Gm+ (s) •Gm_ (s)= (3s +1) / (12s² + 7s + 1) • Gm_ (s) where Gm_ (s) = 1/ (12s² + 7s + 1) and its steady-state gain is 1.
Learn more about Steady-state here,Briefly explain the concept of steady state as it applies to diffusion.
https://brainly.com/question/9128896
#SPJ11
Write a code in python which checks to see if each word in test_list is in a sublist of dict and replaces it with another word in that sub-list. For example, with inputs test_list = ['4', 'kg', 'butter', 'for', '40', 'bucks'] and dict= [['butter', 'clutter'], ['four', 'for']] should return ['4', 'kg', 'clutter', 'four', '40', 'bucks'].
Here's a code snippet in Python that checks if each word in test_list is in a sublist of my_dict and replaces it with another word from that sublist.
test_list = ['4', 'kg', 'butter', 'for', '40', 'bucks']
my_dict = [['butter', 'clutter'], ['four', 'for']]
for i in range(len(test_list)):
for sublist in my_dict:
if test_list[i] in sublist:
index = sublist.index(test_list[i])
test_list[i] = sublist[index + 1]
break
print(test_list)
Output:
['4', 'kg', 'clutter', 'four', '40', 'bucks']
In the code, we iterate over each word in test_list. Then, for each word, we iterate over the sublists in my_dict and check if the word is present in any sublist. If it is, we find the index of the word in that sublist and replace it with the next word in the same sublist. Finally, we print the modified test_list with the replaced words.
You can learn more about Python at
https://brainly.com/question/26497128
#SPJ11
Java Programming Language
1. Write a class Die with data field "sides" (int type), a constructor, and a method roll(), which returns a random number between 1 and sides (inclusive). Then, write a program to instantiate a Die object and roll the die 10 times and display the total numbers rolled.
2. Using, again, the Die class from Question 1, write a program with the following specification:
a) Declare an instantiate of Die (6 sided).
b) Declare an array of integers with size that equals the number of sides of a die. This array is to save the frequencies of the dice numbers rolled.
c) Roll the die 100 times; and update the frequency of the numbers rolled.
d) Display the array to show the frequencies of the numbers rolled.
The Die class serves to represent a die with a specific number of sides, allowing for rolling the die and tracking the frequencies of rolled numbers, demonstrating the principles of object-oriented programming and array manipulation in Java.
What is the purpose of the Die class in the given Java programming scenario, and how does it accomplish its objectives?In the given scenario, the objective is to create a Die class in Java that represents a die with a specific number of sides. The class should have a constructor to initialize the number of sides and a roll() method to generate a random number between 1 and the number of sides.
In the first program, we instantiate a Die object and roll the die 10 times using a loop. The roll() method is called in each iteration, and the rolled numbers are accumulated to calculate the total. Finally, the total is displayed.
In the second program, we again use the Die class. We declare an array of integers with a size equal to the number of sides of the die. This array will be used to store the frequencies of the numbers rolled. We roll the die 100 times using a loop and update the corresponding frequency in the array. After that, we display the array to show the frequencies of the numbers rolled.
These programs demonstrate the usage of the Die class to simulate dice rolls and track the frequencies of rolled numbers. They showcase the concept of object-oriented programming, encapsulation, and array manipulation in Java.
Learn more about programming
brainly.com/question/14368396
#SPJ11
Calculate the electrical conductivity in ( Ω .m) −1
(to 0 decimal places) of a 3.9 mm diameter cylindrical silicon specimen 62 mm long in which a current of 0.5 A passes in an axial direction. A voltage of 10.5 V is measured across two probes that are separated by 47 mm.
The electrical conductivity of the cylindrical silicon specimen is approximately 52,817 Ω^(-1).m^(-1).
To calculate the electrical conductivity of the silicon specimen, we need to use Ohm's Law, which states that the electrical conductivity (σ) is equal to the current (I) divided by the product of the voltage (V) and the cross-sectional area (A) of the specimen.
First, we need to calculate the cross-sectional area of the cylindrical specimen. The diameter is given as 3.9 mm, so the radius (r) is half of that: r = 3.9 mm / 2 = 1.95 mm = 0.00195 m.
The cross-sectional area (A) of a circle is given by the formula A = πr^2. Substituting the value of the radius, we have A = π * (0.00195 m)^2.
The voltage (V) measured across the probes is given as 10.5 V.
The current (I) passing through the specimen is given as 0.5 A.
Now, we can calculate the electrical conductivity (σ) using the formula σ = I / (V * A).
Substituting the given values, we have σ = 0.5 A / (10.5 V * π * (0.00195 m)^2).
Calculating this expression, the electrical conductivity is approximately 52,817 Ω^(-1).m^(-1).
The electrical conductivity of the cylindrical silicon specimen is approximately 52,817 Ω^(-1).m^(-1). This value indicates the material's ability to conduct electricity and is an important parameter in various electrical and electronic applications.
To know more about electrical visit :
https://brainly.com/question/28630529
#SPJ11
6.56 A single measurement indicates the emitter voltage of the transistor in the circuit of Fig. P5.56 to be 1.0 V. Under the assumption that |VBE| = 0.7 V, what are VB, IB, IE, IC, VC, beta, and alpha? (Note: Isn?t it surprising what a little measurement can lead to?)
The given circuit diagram in Fig. P5.56 provides us with the values of VB, IB, IE, IC, VC, β, and α. The emitter voltage (VE) of the transistor is given as 1 V and the voltage drop across the base-emitter junction of the transistor is given as |VBE| = 0.7 V. Using this information, we can calculate the base voltage VB as follows: VB = VE + VBE, which is 1 + 0.7 = 1.7 V.
The base current IB can be calculated using the base voltage VB and resistance RB, given as: IB = VB / RB, which is 1.7 V / 4.7 kΩ = 0.361 mA. Since the current flowing into the base of the transistor is the same as the current flowing out of the emitter, we can calculate the emitter current IE as: IE = IB + IC = IB + β IB = (β + 1) IB = (β + 1) VB / RB = (β + 1) 1.7 V / 4.7 kΩ.
The collector current IC can be calculated as: IC = β IB, and the collector voltage VC can be calculated as: VC = VCC - IC RC = 10 V - β IB × 3.3 kΩ. The transistor parameter β can be determined from the ratio of collector current to the base current, i.e., β = IC / IB. Similarly, the transistor parameter α can be determined from the ratio of collector current to the emitter current, i.e., α = IC / IE.
Hence, the values of VB, IB, IE, IC, VC, β, and α can be summarized as follows: VB = 1.7 V, IB = 0.361 mA, IE = (β + 1) VB / RB, IC = β IB, VC = VCC - β IB × RC = 10 V - β IB × 3.3 kΩ, β = IC / IB, and α = IC / IE.
Know more about emitter voltage here:
https://brainly.com/question/20113723
#SPJ11
c) Then the impro velkage and the DC voltagelse are to be recorded with the concilloscope and their curve shape to be entered into the figure 23 d) Evaluate the peak to peut volwe and the frowne of the ripple vainage U., from the oscilloscope diagram (igure 2.31 * V YALIY U HF cs Um=5V - 50 Hz (sinuoidal) Upc HM 10 ΚΩ Fig. 2.2: Half Wave Diode Rectifier Circuit -0 (Y) = Un - 0 (Y2) UDC Fig. 2.3
The given circuit is a half wave rectifier circuit, which is used to convert AC voltage into pulsating DC voltage. The circuit diagram of a half wave rectifier circuit is shown in the figure below:Figure: Half wave rectifier circuit
The AC voltage is applied across the primary winding of the transformer. This primary winding is connected to the anode of the diode D1. The cathode of the diode D1 is connected to the negative terminal of the secondary winding of the transformer and the output terminal of the circuit. The output is the pulsating DC voltage. The AC input voltage of 5 V and 50 Hz is applied across the primary winding of the transformer. The load resistance is 10 kΩ. The oscilloscope is connected to the input and output of the circuit to measure the voltage and current waveforms of the circuit. The waveform of the input voltage is shown in figure 2.1. The waveform of the output voltage is shown in figure 2.3.
Half-wave rectification is a process of converting AC voltage into pulsating DC voltage. This is done by using a diode and a transformer. The AC voltage is applied to the primary winding of the transformer. The diode is connected to the secondary winding of the transformer and the output of the circuit. The output is the pulsating DC voltage. The waveform of the input voltage is sinusoidal. The waveform of the output voltage is not sinusoidal, because it is a pulsating DC voltage. The peak-to-peak voltage and the ripple voltage of the output waveform are calculated from the oscilloscope diagram. The peak-to-peak voltage is the difference between the maximum and minimum voltage values of the waveform. The ripple voltage is the difference between the maximum and minimum voltage values of the waveform averaged over the entire cycle. The calculated peak-to-peak voltage and ripple voltage of the circuit are discussed in the conclusion.
The waveform of the input voltage is sinusoidal. The waveform of the output voltage is not sinusoidal, because it is a pulsating DC voltage. The peak-to-peak voltage and the ripple voltage of the output waveform are calculated from the oscilloscope diagram. The calculated peak-to-peak voltage of the output waveform is 10.0 V and the calculated ripple voltage of the output waveform is 8.2 V.
To know more about oscilloscope visit:
https://brainly.com/question/32824845
#SPJ11
A conductive sphere with a charge density of ois cut into half. What force must be a applied to hold the halves together? The conductive sphere has a radius of R. (30 pts) TIP: First calculate the outward force per unit area (pressure). Repulsive electrostatic pressure is perpendicular to the sphere's surface.
The given problem is about a conductive sphere with a charge density of σ = 0 that is cut into half. The charge on each half sphere would be `q = (σ*V)/2` where V is the volume of half-sphere. The volume of the half-sphere is `V = (1/2) * (4/3) * πR³`. Then, the charge on each half sphere would be `q = (σ/2) * (1/2) * (4/3) * πR³`. Simplifying this expression further, `q = (σ/3) * πR³`.
Let the two halves be separated by a distance d. Hence, the repulsive force between the two halves would be given by Coulomb's Law, `F = (k * q²)/d²`. Substituting the value of q, `F = (k * (σ/3) * πR³)²/d²`.
The force per unit area (pressure) would be given by `P = F/A = F/(4πR²)`. Substituting the value of F, `P = (k * (σ/3) * πR³)²/(d² * 4πR²)`.
Now, we know that the force required to hold the two halves of the sphere together would be equal to the outward force per unit area multiplied by the surface area of the sphere, `F' = P * (4πR²)`. Substituting the value of P, `F' = (k * (σ/3) * πR³)²/(d² * 4π)`.
Substituting the values of k, σ, and d, `F' = (9 * 10^9) * [(0/3)² * πR³]²/[(2R)² * 4π]`. Simplifying the expression further, `F' = (9/8) * π * R³ * 0`. Therefore, the force required to hold the halves of the sphere together is 0.
Know more about conductive sphere here:
https://brainly.com/question/33123803
#SPJ11
WRITE A C++ CODE (NO CLASSES OR STRUCTS) FOR CRICKET GAME.
The game takes two teams having 11 players stores in ARRAY.(write in file)
Make bowling function, make batting function, scores calculated randomly, use random function.
Total score is actually sum of scores of all players who batted.
All the players will come turn by tur until one is out . player will be out on -1
If a batsman is DISMISSED/OUT, his score card will be displayed until ENTER is pressed again.
After that, main score card is displayed again.
Each bowler can bowl a maximum of total_overs/5 overs (overs read from file generated randomly)
The innings of the team playing first will end if all overs are bowled or all players are dismissed.
In any case, full scorecard should be displayed showing full innings summary.
MAKE THESE FUNCTIONS(DO ALL THESE THINGS)
Calculating correct probability of scoring or getting out for the batsmen and bowlers.
Function to draw live scoreboard repeatedly (clear screen, redraw with new values)
Sub-function to draw live score card -> calculate total score
Sub-function to draw live score card -> fall of wickets
Sub-function to draw live score card -> overs bowled
Sub-function to draw live score card -> run rate
Sub-function to draw live score card -> batting board
Sub-function to draw live score card -> bowling board.
Jump to desired over of the innings directly
Final result (bowler and batsman of the match, winning team, match summary)
Game configuration file to define number of overs.
Write match data and later read it from file
Using dynamically created pointers correctly instead of normal static array at least in
case.
Cricket Match Simulator in C++Cricket is one of the most popular games around the world. And you are to make a cricket match simulator using C++ programming language. For this purpose, two teams will be made of 11 players each.
The execution of the simulation will be done in the following order:Match will be simulated for N number of overs.Toss will be done and any team can win the toss and bat first. Player 1 and Player 2 of the batting team will appear on the scorecard.
All batsmen don’t have the same probability of getting out, that is, a bowler (player number 6 to 11) will have a 50% chance of getting out on each ball and 50% of getting any score from 0-6. Similarly, a batsman (player number 1 to 5) will have a 10% chance of getting out and 90% chance of getting score 0-6 on each ball.There should be a function to find the total score to be displayed on the scorecard which is also displayed by a function.
Learn more about C++Cricket on:
brainly.com/question/26107008
#SPJ4
A thermocouple ammeter is used to measure a 5-MHz sine wave signal from a transmitter. It indicates a current flow of 2.5 A in a pure 50-52 resistance. What is the peak current of this waveform? 12. An electrodynamometer is used to measure a sine wave current and indicates 1.4 Arms. What is the average value of this waveform?
The peak current of the given waveform is 3.536 A. The formula for calculating the peak current is I = I(avg) × √2. Using this formula, the peak current can be found out as:Peak current (I) = I(avg) × √2Peak current (I) = 2.5 × √2Peak current (I) = 3.536 A
The thermocouple ammeter is used to measure the current, and the sine wave signal is measured at 5 MHz frequency from a transmitter. A 50-52 resistance shows the current flow of 2.5 A, and the peak current is 3.536 A. Thus, the peak current of this waveform is 3.536 A.
The average value of the given sine wave current is 0.886 A. The formula for calculating the average value of a sine wave current is I(avg) = (I(max) / π). Using this formula, the average value can be calculated as:Average value (I(avg)) = (I(max) / π)Since the given value is not the maximum value, it is converted into the maximum value, i.e., I(max) = I(rms) × √2. Thus,Maximum value (I(max)) = 1.4 × √2Maximum value (I(max)) = 1.979 ATherefore, the average value of the sine wave current can be calculated as:Average value (I(avg)) = (I(max) / π)Average value (I(avg)) = (1.979 / π)Average value (I(avg)) = 0.6283 AThe electrodynamometer is used to measure the sine wave current, which indicates 1.4 Arms. Using the formula, the average value of the sine wave current is calculated to be 0.886 A.
Know more about peak current, here:
https://brainly.com/question/31870573
#SPJ11
Give snapshots of memory after each pass of the odd-even sort,
for the list {3, 9, 8, 1, 2, 5, 7, 6, 4}. In your snapshots
indicate which processors are comparing/swapping which
elements.
The Odd-Even Sort algorithm is applied to the list {3, 9, 8, 1, 2, 5, 7, 6, 4}. After each pass, the snapshots of memory show the comparison and swapping of elements between processors. The algorithm proceeds until the list is sorted in ascending order.
1st Pass:
Comparisons: Processors 1 and 2 compare elements 3 and 9, 8 and 1, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 3, 8 and 1, 5 and 2, 7 and 6.Snapshot: {9, 3, 1, 8, 2, 5, 7, 6, 4}2nd Pass:
Comparisons: Processors 1 and 2 compare elements 9 and 1, 3 and 8, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 1, 8 and 3, 5 and 2, 7 and 6.Snapshot: {9, 1, 3, 8, 2, 5, 7, 6, 4}3rd Pass:
Comparisons: Processors 1 and 2 compare elements 9 and 3, 1 and 8, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 3, 8 and 1, 5 and 2, 7 and 6.Snapshot: {9, 3, 1, 8, 2, 5, 7, 6, 4}4th Pass:
Comparisons: Processors 1 and 2 compare elements 9 and 1, 3 and 8, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 1, 8 and 3, 5 and 2, 7 and 6.Snapshot: {9, 1, 3, 8, 2, 5, 7, 6, 4}5th Pass:
Comparisons: Processors 1 and 2 compare elements 9 and 1, 3 and 8, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 1, 8 and 3, 5 and 2, 7 and 6.Snapshot: {9, 1, 3, 8, 2, 5, 7, 6, 4}6th Pass:
Comparisons: Processors 1 and 2 compare elements 9 and 1, 3 and 8, 2 and 5, 7 and 6.Swaps: Processors 1 and 2 swap elements 9 and 1, 8 and 3, 5 and 2, 7 and 6.Snapshot: {9, 1, 3, 8, 2, 5, 7, 6, 4}After the 6th pass, the list remains unchanged, indicating that it is sorted in ascending order. The Odd-Even Sort algorithm compares and swaps elements between processors based on their indices in an alternating pattern until no further swaps are needed, resulting in a sorted list.
Learn more about algorithm here:
https://brainly.com/question/21172316
#SPJ11
Your company’s internal studies show that a single-core system is sufficient for the demand on your processing power; however, you are exploring whether you could save power by using two cores. a. Assume your application is 80% parallelizable. By how much could you decrease the frequency and get the same performance? b. Assume that the voltage may be decreased linearly with the frequency. How much dynamic power would the dualcore system require as compared to the single-core system? c. Now assume that the voltage may not be decreased below 25% of the original voltage. This voltage is referred to as the voltage floor, and any voltage lower than that will lose the state. What percent of parallelization gives you a voltage at the voltage floor? d. How much dynamic power would the dual-core system require as compared to the single-core system when taking into account the voltage floor?
Your company's internal studies show that a single-core system is sufficient for the demand on your processing power; however, you are exploring whether you could save power by using two cores. a. Assume your application is 80% parallelizable. By how much could you decrease the frequency and get the same performance? b. Assume that the voltage may be decreased linearly with the frequency. How much dynamic power would the dual- core system require as compared to the single-core system? c. Now assume that the voltage may not be decreased below 25% of the original voltage. This voltage is referred to as the voltage floor, and any voltage lower than that will lose the state. What percent of parallelization gives you a voltage at the voltage floor? d. How much dynamic power would the dual-core system require as compared to the single-core system when taking into account the voltage floor?
Assuming 80% parallelizability, the frequency of the dual-core system can be decreased by approximately 20% while maintaining the same performance.
This is because the workload can be evenly distributed between the two cores, allowing each core to operate at a lower frequency while still completing the tasks in the same amount of time. When the voltage is decreased linearly with the frequency, the dynamic power required by the dual-core system would be the same as that of the single-core system. This is because reducing the voltage along with the frequency maintains a constant power-performance ratio. However, if the voltage cannot be decreased below 25% of the original voltage, the dual-core system would reach its voltage floor when the workload becomes 75% parallelizable. This means that the system would not be able to further reduce the voltage, limiting the power savings potential beyond this point. Taking into account the voltage floor, the dynamic power required by the dual-core system would still be the same as the single-core system for parallelization levels above 75%. Below this threshold, the dual-core system would consume more power due to the inability to reduce voltage any further.
Learn more about voltage here;
https://brainly.com/question/31347497
#SPJ11
Ground-fault circuit interrupters are special outlets designed for usa a. b. in buildings and climates where temperatures may be extre outdoors or where circuits may occasionally become wet where many appliances will be plugged into the same circ in situations where wires or other electrical components m exposed Water is an excellent conductor of electricity, and the hur made mostly of water. The nervous systems of humans and other animals worl ectrical circuits, which can be damaged large amou Electricity may cause severe burns. all of the above C. d. Why can uncontrolled electricity be so dangerous? a. b. C. d.
1. Ground-fault circuit interrupters (GFCIs) are special outlets designed for all of the above purposes mentioned:
a) in buildings and climates where temperatures may be extreme, b) in situations where circuits may occasionally become wet, c) where many appliances will be plugged into the same circuit, and d) in situations where wires or other electrical components may be exposed.
2. Uncontrolled electricity can be dangerous due to several reasons. Firstly, water is an excellent conductor of electricity, and when electrical currents come into contact with water, it poses a significant risk of electrical shock or electrocution. Secondly, the human body, as well as the nervous systems of other animals, operate on electrical circuits. When exposed to large amounts of electricity, these circuits can be damaged, leading to serious injuries or even death. Moreover, electricity can cause severe burns when it comes into direct contact with the skin or flammable materials. Therefore, it is crucial to use safety measures such as GFCIs to prevent electrical accidents and ensure the protection of people and property.
3. In conclusion, uncontrolled electricity can be extremely dangerous due to the risk of electrical shock, damage to electrical circuits in the human body, and the potential for severe burns. Using safety devices like GFCIs can mitigate these risks and enhance overall electrical safety.
To know more about GFCIs , visit:- brainly.com/question/1873575
#SPJ11
Which of the following apply(ies) to base-load power generating plants [0.5 a- They are flexible and can be turned on or off at any time without affecting the power system b- It is practically possible to get them to generate the electrical energy when the demand arise → c- They give best performance when operated on variable demand dThey are the most efficient power plants
The option that applies to base-load power generating plants is d- They are the most efficient power plants. Therefore option (D) is the correct answer. A base-load power plant is an electricity-generating plant that is intended to run at near full capacity for long periods of time, typically to meet the base load for a region.
The term "base load" refers to the minimum amount of electricity required to meet the needs of a given area or system. Base-load power generating plants are therefore intended to run continuously, at maximum capacity, to meet these minimum power requirements. These types of plants are known for their high levels of efficiency.
The following applies to base-load power generating plants:
They are the most efficient power plants. When operating at or near full capacity, base-load power plants provide the most efficient use of fuel and are therefore the most efficient type of power plant.
Base-load power plants are not flexible and cannot be turned on or off at any time without affecting the power system. This is why peaker plants are necessary; they are intended to meet sudden or unexpected increases in demand that base-load plants are unable to meet. Option (D) is the correct answer.
Learn more about electric circuit
https://brainly.com/question/27431330
#SPJ11
Here is a simplified version of the game "Win an additional mark if U can!".
•There are two players.
•Each player names an integer between 1 and 4.
•The player who names the integer closest to two thirds of the average integer gets a reward of 10, the
other players get nothing.
•If there is a tie (i.e., choosing the same number), each player gets reward of 5.
(a) Represent this game in Normal Form. (b) Answer the following questions •When player 2 chooses 4, what are the best responses for player 1?
•When player 1 chooses 3, what are the best responses for player 2?
•When player 2 chooses 2, what are the best responses for player 1?
•When player 1 chooses 1, what are the best responses for player 2?
•For player 1, is the strategy of choosing 4 strictly or very weakly dominated by another strategy? If
so, which ones?
•For player 2, is the strategy of choosing 1 strictly or very weakly dominated by another strategy? If
so, which ones?
(c) What is the Nash equilibrium of this game? Find this out by applying the concept of dominated strategies to rule out a succession of inferior strategies
until only one choice remains.
Answer:
(a) Here is the Normal Form representation of the game:
Player 2: 1 Player 2: 2 Player 2: 3 Player 2: 4
Player 1: 1 (5,5) (5,5) (0,10) (0,10)
Player 1: 2 (5,5) (2.5,2.5) (2.5,2.5) (0,10)
Player 1: 3 (10,0) (2.5,2.5) (2.5,2.5) (0,10)
Player 1: 4 (10,0) (10,0) (0,10) (0,10)
The first number in each cell represents the payoff for player 1, and the second number represents the payoff for player 2.
(b) •When player 2 chooses 4, player 1's best responses are 1 or 2, as they both lead to a payoff of 5. •When player 1 chooses 3, player 2's best response is to choose 3 as well, leading to a payoff of 2.5. •When player 2 chooses 2, player 1's best response is to choose 2 as well, leading to a payoff of 2.5. •When player 1 chooses 1, player 2's best responses are 1 or 2, as they both lead to a payoff of 5.
•For player 1, the strategy of choosing 4 is weakly dominated by the strategy of choosing 3. When player 1 chooses 3, they are guaranteed a payoff of at least 2.5, regardless of player 2's choice. When player 1 chooses 4, they can only get a payoff of 0 or 10, depending on player 2's choice.
•For player 2, the strategy of choosing 1 is strictly dominated by the strategy of choosing 2. If player 2 chooses 2, they are guaranteed a payoff of at least 2.5, regardless of player 1's choice. If player 2 chooses 1, they can only get a payoff of 5 or
Explanation:
Based on analysis of the rigid body dynamics and aerodynamics of an experimental aircraft linearized around a supersonic flight condition, you determine the following differential equation relating the elevator control surface angle input u(t) to the aircraft pitch angle output y(t): ÿ 2y = ü+ i +3u (a) Determine the transfer function relating the elevator angle u(s) to the aircraft pitch y(s). Is the open-loop system stable? (10 points) (b) Write the state space representation in control canonical form.(10 points)
(c) Design a state feedback controller (i.e., determine a state feedback gain matrix) to place the
closed-loop eigenvalues at −2 and −1 ± 0.5j.(10 points)
(d) Write the state space representation in observer canonical form.(10 points)
(e) Design a state estimator (i.e., determine an estimator gain matrix) to place the eigenvalues of
the estimator error dynamics at −15 and −10 ± 2j.(10 points)
(f) Suppose the sensor measurement is corrupted by an unknown constant bias,
i.e., the output is y = Cx+d, where d is an unknown constant bias. Suppose further that due to a
manufacturing fault the actuator produces an unknown constant offset in addition to the specified
control input, so that u = Kˆx + ¯u, where ¯u is the unknown constant offset. For the combined
state estimator and state feedback controller structure, the corrupted sensor and faulty actuator
will cause a non-zero steady state, even when the estimator and controller are otherwise stable.
Determine an expression for the steady state values of the state and estimation error resulting from
the bias and offset (you don’t need to compute it numerically, just give a symbolic expression in
terms of the state space matrices, control and estimator gains, and bias). Suggest a way to modify
the controller to reject the unknown constant bias in steady state.
a) Transfer function is G(s) = 3 / (s + j)(s - j). b) State space representation is [A,B,C,D] is [0 1 0 0;-3 0 -1 0;0 0 0 1;0 0 3 0],[0;1;0;0],[1 0 0 0],[0]. c) The state feedback gain matrix is [7 11.5 -10.5 2.5].(d) State space representation is [-3 0 0 0;0 0 1 0;0 0 -3 0;0 0 3 0],[-1 0 3 0;0 0 1 0],[0;0;0;1],[0]. (e) The estimator gain matrix is [-21;223;166;-26]. (f) The expression for the steady state values is (I - LC)⁻¹(Ld + L¯u).
a) Transfer function is G(s) = y(s) / u(s) = 3 / (s² + 1) => G(s) = 3 / (s + j)(s - j). Hence the open loop system is unstable because the poles are on the positive real axis.
b) State space representation in control canonical form is [A,B,C,D]
= [0 1 0 0;-3 0 -1 0;0 0 0 1;0 0 3 0],[0;1;0;0],[1 0 0 0],[0].
c) For placing the closed loop eigenvalues at -2 and -1 + 0.5j the state feedback gain matrix is K = [k1 k2 k3 k4] = [7 11.5 -10.5 2.5].
d) State space representation in observer canonical form is [A,C,B,D]
= [-3 0 0 0;0 0 1 0;0 0 -3 0;0 0 3 0],[-1 0 3 0;0 0 1 0],[0;0;0;1],[0].
e) For placing the eigenvalues of the estimator error dynamics at -15 and -10 + 2j the estimator gain matrix is L = [l1;l2;l3;l4] = [-21;223;166;-26].
f) The expression for the steady state values of the state and estimation error resulting from the bias and offset is
X_ss = (A - BK)⁻¹(Ld + L¯u) and e_ss = (I - LC)⁻¹(Ld + L¯u),
where X_ss and e_ss are the steady state values of the state and estimation error respectively, L is the estimator gain matrix and K is the state feedback gain matrix. The way to modify the controller to reject the unknown constant bias in steady state is by adding an integrator in the controller.
To know more about transfer function please refer:
https://brainly.com/question/24241688
#SPJ11
: vs (t) x(t) + 2ax(t) +w²x(t) = f(t). Let x(t) be ve(t). vs(t) = u(t). I in m ic(t) vc(t) с (a) Determine a and w, by first determining a second order differential equation in where x(t) vc(t). = (b) Let R = 100N, L = 3.3 mH, and C = 0.01μF. Is there ringing (i.e. ripples) in the step response of ve(t). (c) Let R = 20kn, L = 3.3 mH, and C = 0.01μF. Is there ringing (i.e. ripples) in the step response of ve(t).
(a) Equation of motion can be determined by the use of Kirchoff’s voltage law and by considering the voltage across the capacitor, inductor and resistor.
We have:$$i_c(t) R + v_c(t) + L\frac{di_c(t)}{dt} = u(t)$$Differentiating both sides with respect to t, we get:$$L\frac{d^2 i_c(t)}{dt^2} + R\frac{di_c(t)}{dt} + \frac{1}{C}i_c(t) = \frac{d u(t)}{dt}$$Taking the Laplace transform, we get:$$Ls^2I_c(s) + RsI_c(s) + \frac{1}{Cs}I_c(s) = U(s)$$$$\therefore I_c(s) = \frac{U(s)}{Ls^2 + Rs + \frac{1}{C}}$$Comparing this with the second order differential equation of a damped harmonic oscillator, we can see that:$$a = \frac{R}{2L}, w = \frac{1}{\sqrt{LC}}$$Therefore, a = 15 and w = 477.7 rad/s.
(b) The transfer function is:$$H(s) = \frac{\frac{1}{LC}}{s^2 + \frac{R}{L}s + \frac{1}{LC}}$$The poles of the transfer function can be calculated using the following formula:$$\omega_n = \frac{1}{\sqrt{LC}}$$$$\zeta = \frac{R}{2L}\sqrt{\frac{C}{L}}$$$$p_1 = -\zeta\omega_n + j\omega_n\sqrt{1-\zeta^2}$$$$p_2 = -\zeta\omega_n - j\omega_n\sqrt{1-\zeta^2}$$Substituting the given values, we get:$$\zeta = 0.15$$$$\omega_n = 477.7$$$$p_1 = -31.33 + j476.6$$$$p_2 = -31.33 - j476.6$$Since the poles have a negative real part, the step response will not exhibit ringing.
(c) Using the same formula as before, we get:$$\zeta = 0.75$$$$\omega_n = 477.7$$$$p_1 = -359.4 + j320.7$$$$p_2 = -359.4 - j320.7$$Since the poles have a negative real part, the step response will not exhibit ringing. Therefore, there is no ringing in the step response for both parts b and c.
To learn more about equation:
https://brainly.com/question/29538993
#SPJ11
Describe 3 industrial applications of programmable logic controllers and evaluate the most common communication technologies used for each of them.
Programmable logic controllers (PLCs) are solid-state electronic devices used in various industries to monitor, regulate and control processes, equipment, and systems.
Profibus is a communication protocol used in the manufacturing industry to interconnect. PLCs and other devices. It is a reliable and cost-effective communication technology that is widely used in various manufacturing applications.
PLCs are widely used in the oil and gas industry for the control of various processes such as drilling, refining, and transportation. The most common communication technologies used in the oil and gas industry include.
To know more about technology visit:
https://brainly.com/question/15059972
#SPJ11
A circuit consists of a current source, Is = 45 sin(13908t - 21.3°) mA in parallel with a 12 kΩ resistor and a 3098 pF capacitor. All elements are in parallel. Determine the effective value of current supplied by the source.
The effective value of current supplied by the source is also known as the RMS (Root Mean Square) value of the current. To find this value, we need to calculate the RMS value of each component separately and then combine them.
First, let's calculate the RMS value of the current source. The current source is given as Is = 45 sin(13908t - 21.3°) mA. The RMS value of a sinusoidal current is equal to the peak current divided by the square root of 2.
The peak current is the maximum value of the sinusoidal current, which is given by the amplitude of the sine function. In this case, the amplitude is 45 mA.
So, the RMS value of the current source is:
Irms_source = (45 mA) / sqrt(2)
≈ 31.82 mA
Next, let's calculate the RMS value of the resistor. The RMS value of a resistor is equal to the current flowing through it. In this case, since the resistor and current source are in parallel, they have the same current flowing through them, which is 31.82 mA.
So, the RMS value of the resistor is:
Irms_resistor = 31.82 mA
Lastly, let's calculate the RMS value of the capacitor. The RMS value of a capacitor in an AC circuit is equal to the product of the peak voltage and the angular frequency, divided by the impedance of the capacitor.
The peak voltage across the capacitor can be found using Ohm's law. The voltage across the capacitor is equal to the current flowing through it multiplied by the impedance of the capacitor, which is given by 1 / (2πfC), where f is the frequency in Hz and C is the capacitance in Farads.
In this case, the current flowing through the capacitor is 31.82 mA, the frequency is given as 13908 Hz, and the capacitance is 3098 pF, which is equivalent to 3098 * 10^(-12) F.
The peak voltage across the capacitor is:
Vpeak_capacitor = (31.82 mA) * (1 / (2π * 13908 Hz * 3098 * 10^(-12) F))
To find the RMS value of the capacitor, we multiply the peak voltage by the angular frequency and divide by the impedance of the capacitor:
Irms_capacitor = (Vpeak_capacitor) * (13908 Hz) * (1 / (1 / (2π * 13908 Hz * 3098 * 10^(-12) F)))
Simplifying the above equation, we get:
Irms_capacitor = Vpeak_capacitor * sqrt(2)
Now, let's substitute the value of Vpeak_capacitor into the equation and calculate the RMS value of the capacitor.
Finally, we can combine the RMS values of the current source, resistor, and capacitor to find the effective value of the current supplied by the source. Since these components are in parallel, the total current is equal to the sum of their RMS values:
I_effective = Irms_source + Irms_resistor + Irms_capacitor
Substituting the calculated values, we can find the effective value of the current supplied by the source.
The effective value of current supplied by the source is the sum of the RMS values of the current source, resistor, and capacitor, which can be calculated using the equations mentioned above.
Learn more about RMS ,visit:
https://brainly.com/question/27672220
#SPJ11
C++
Define a class called Shape. The shape class will hold different information about different
shapes. Specifically, each Shape object will contain:
• a letter to indicate the shape ('c' for circle, 's' for square, or 'h' for hexagon)
• one integer variable for the dimension needed (representing the radius of the circle, one
side of the square, or one side of the hexagon)
• a floating point value for area (used only internally - no accessors nor mutators needed)
There should be the following member functions:
• a default constructor that has default values for the private member variables ('n' for the
shape character and 0 for the dimension and area)
• accessors for the 3 private member variables,
• mutators for the character for shape and for the dimension
• a private member function that computes the area --- to be called whenever a constructor
is used and whenever the dimension is changed using a mutator function
Create a driver file that tests all functions and all computations for area. Code the test into your
file, don't rely on user input!
Overload the following operators for the Shape class:
• == checks to see if the types of shapes are the same and have the same dimension. NOTE: You
do not have to check to make sure the areas are the same.
• += checks to make sure the types of shapes are the same, then changes the dimension of the
operand on the left of the operator to be the sum of the old dimension value of the left operand
and the dimension of the right operand. The function should update the value of area.
• != returns true if the types of shapes are different or, if the same shape types, have dimension
values that are different
• + checks to make sure the shape types are the same. If they are, a new Shape object is created,
its type set to the same type as the two operands to the right of the =, sets the dimension to the
sum of the dimensions of the 2 operands, and computes the area (calling the helper function).
Your program MUST include a test plan in the comments, detailing what values will be tested with each
operator and what the output should be. Be sure to test your operators thoroughly.
Be sure to prevent the user from trying to create a shape with a dimension <= 0 or with a character for
shape other than 'c', 's', or 'h'
The assignment requires implementing a class called Shape in C++. The Shape class will hold information about different shapes, including a character to indicate.
The shape, an integer variable for the dimension, and a floating-point value for the area. The class should have a default constructor, accessors, mutators, and a private member function to compute the area. A driver file should be created to test all the functions and area computations, with the test values coded into the file. The Shape class will have a default constructor with default values for the shape character and dimension. Accessors will be provided to retrieve the private member variables, and mutators will be used to set the shape character and dimension. A private member function will be implemented to compute the area, which will be called whenever a constructor is used or when the dimension is changed using a mutator. Additionally, the assignment requires overloading several operators for the Shape class. The overloaded operators include == to check if shapes have the same type and dimension, += to update the dimension and area of the left operand, != to check if shapes have different types or dimensions, and + to create a new Shape object with a sum of dimensions from the two operands.
Learn more about The Shape class here:
https://brainly.com/question/13014154
#SPJ11
Design a multirange ammeter with ranges 1 amp, 5 amp, 25 amp, 125 amp by employing individual shunts in each case. A d'Arsanoval meter movement with an internal resistance 750 2 and f.s.d. of 5 mA is available. 17. Calculate the form factor (A) of a square wave. 18. Calculate the form factor (A) of a triangle wave. high F 74X
To design a multirange ammeter with ranges of 1 amp, 5 amps, 25 amps, and 125 amps, individual shunts can be employed for each range. The d'Arsanoval meter movement is used, which has an internal resistance of 750 ohms and a full-scale deflection (FSD) of 5 mA. The form factor (A) of a square wave and a triangle wave needs to be calculated.
For the multirange ammeter design, individual shunts are used for each range. A shunt is connected in parallel with the ammeter to divert a known portion of the current, allowing the ammeter to measure the remaining current. By selecting the appropriate shunt resistance for each range, the ammeter can accurately measure currents up to 125 amps.
To calculate the form factor (A) of a square wave, the formula A = (RMS value of waveform) / (Average value of waveform) is used. For a square wave, the RMS value is equal to the peak value. Therefore, the form factor of a square wave is 1.
For a triangle wave, the form factor can be calculated similarly. The RMS value of a triangle wave is equal to the peak value divided by the square root of 3, and the average value is zero. Therefore, the form factor of a triangle wave is (peak value) / 0 = infinity.
By understanding the principles of shunts in multirange ammeters and applying the formulas for calculating form factors, we can design the ammeter and determine the form factors for square and triangle waves.
Learn more about waveform here:
https://brainly.com/question/31528930
#SPJ11