Using Adams's method with d = 16 to apportion the new officers among the precincts as Precinct A: 39 officers, Precinct C: 47 officers, Precinct D: 20 officers, Precinct E: 29 officers, Precinct F: 39 officers.
To apportion the 175 new officers among the six precincts using Adams's method with d = 16, we need to follow these steps:
1. Calculate the crime ratios for each precinct by dividing the number of crimes by the square root of the number of officers already assigned to that precinct.
- Precinct A: Crime ratio = 436 / √(16) = 109
- Precinct C: Crime ratio = 522 / √(16) = 131
- Precinct D: Crime ratio = 218 / √(16) = 55
- Precinct E: Crime ratio = 324 / √(16) = 81
- Precinct F: Crime ratio = 433 / √(16) = 108
2. Calculate the total crime ratio by summing up the crime ratios of all precincts.
Total crime ratio = 109 + 131 + 55 + 81 + 108 = 484
3. Calculate the apportionment for each precinct by multiplying the total number of officers (175) by the crime ratio for each precinct, and then dividing it by the total crime ratio.
- Precinct A: Apportionment = (175 * 109) / 484 = 39 officers
- Precinct C: Apportionment = (175 * 131) / 484 = 47 officers
- Precinct D: Apportionment = (175 * 55) / 484 = 20 officers
- Precinct E: Apportionment = (175 * 81) / 484 = 29 officers
- Precinct F: Apportionment = (175 * 108) / 484 = 39 officers
So, according to Adams's method with d = 16, the new officers should be apportioned as follows:
- Precinct A: 39 officers
- Precinct C: 47 officers
- Precinct D: 20 officers
- Precinct E: 29 officers
- Precinct F: 39 officers
This apportionment aims to allocate the officers in a way that takes into account the crime rates of each precinct relative to their existing officer counts.
Learn more about the Adams's method from the given link-
https://brainly.com/question/32735598
#SPJ11
Reflecting surfaces need to be about the same size as the sound waves that they are reflecting. Therefore, if you wanted to make a reflector that was capable of reflecting a 60 Hz sound what would the minimum size of the reflector need to be? A. 20 ft. B. 15 ft. C. 10 ft. D. SAL.
The minimum size of the reflector needed to reflect a 60 Hz sound wave would be approximately A)20 ft.
The reason for this is that in order for a reflecting surface to effectively reflect sound waves, it needs to be about the same size as the wavelength of the sound wave. The wavelength of a sound wave is determined by its frequency, which is the number of cycles the wave completes in one second. The formula to calculate wavelength is wavelength = speed of sound/frequency.
In this case, the frequency is 60 Hz. The speed of sound in air is approximately 343 meters per second. Therefore, the wavelength of a 60 Hz sound wave would be approximately 5.7 meters.
To convert meters to feet, we divide by 0.3048 (1 meter = 3.28084 feet). Therefore, the minimum size of the reflector needed would be approximately 18.7 feet.
Hence the correct option is A)20 ft.
For more similar questions on sound wave
brainly.com/question/1417453
#SPJ8
does most prodrugs designed in this decade follow a
computer-aided drug design approach given that they are trying to
optimize the original drug?
In recent years, computer-aided drug design has been widely used to optimize prodrugs by predicting their behavior, properties, and interaction with the body, saving time and resources compared to traditional methods.
Most prodrugs designed in this decade do follow a computer-aided drug design approach in order to optimize the original drug. This approach involves the use of computational tools and techniques to identify, design, and optimize potential prodrugs.
1. Computer-aided drug design (CADD) is a powerful tool used by pharmaceutical researchers to accelerate the drug discovery and development process.
2. Prodrugs are inactive or less active compounds that are designed to be converted into active drugs once inside the body. They are often used to improve drug delivery, enhance stability, or reduce side effects.
3. In order to optimize the original drug, researchers use CADD to predict the prodrug's behavior and its interaction with the body.
4. CADD techniques involve molecular modeling, computational chemistry, and bioinformatics to analyze the physicochemical properties of the prodrug and its potential for conversion to the active drug form.
5. Researchers can use virtual screening to identify potential prodrugs with desirable properties, such as increased solubility or improved bioavailability.
6. Once potential prodrugs are identified, researchers can use computational methods to predict their stability, metabolic activation, and release of the active drug form.
7. This information is then used to guide the synthesis and experimental testing of the prodrugs.
8. By using a computer-aided approach, researchers can optimize the prodrug design, saving time and resources compared to traditional trial-and-error methods.
It is important to note that while many prodrugs designed in this decade may follow a computer-aided drug design approach, there may also be cases where other approaches are used. The specific approach chosen will depend on the drug target, therapeutic indication, and available resources. However, CADD has become an increasingly important tool in the optimization of prodrugs due to its ability to rapidly screen large chemical libraries and provide valuable insights into their behavior.
To learn more about prodrugs visit : https://brainly.com/question/29852202
#SPJ11
Yesterday a robot assembled 30 phones. Today it has been programmed to do 8 phones each hour for y hours. What will be the total number of phones assembled in both days? Select one: a. 30+8y b. 30y+8 c. 30×8y d. Not Here e. (30+8)y
Total number of phones assembled= 30 + 8y
Total number of phones assembled= 8y + 30
The correct option is (a) 30 + 8y.
Yesterday the robot assembled 30 phones. Today it has been programmed to do 8 phones each hour for y hours. We need to find the total number of phones assembled in both days. Let us solve the problem.
Yesterday the robot assembled 30 phones.So, the number of phones assembled yesterday = 30 Today, the robot will assemble 8 phones each hour for y hours. We need to find the total number of phones assembled today.
Total number of phones assembled today = Number of phones assembled in 1 hour × Number of hours
Number of phones assembled in 1 hour = 8
Number of hours = y
Total number of phones assembled today = 8 × y
Total number of phones assembled today= 8y
Therefore, the total number of phones assembled in both days is given by adding the number of phones assembled yesterday and today.
Total number of phones assembled = Number of phones assembled yesterday + Number of phones assembled today
To now more about yesterday visit :
https://brainly.com/question/31259744
#SPJ11
What is a nucleophilic substitution reaction and how is it
different from an electrophilic substitution reaction? Please show
example reaction of NAS and EAS.
A nucleophilic substitution reaction (NAS) is one in which a nucleophile (a species that has an excess of electrons and can donate a pair of electrons) attacks an electron-deficient species called an electrophile (a species that is electron-deficient). In a nucleophilic substitution reaction, the nucleophile replaces a good leaving group in the electrophile.
A good leaving group is one that is stable when it is expelled from the molecule; halides such as iodides, chlorides, and bromides, as well as some other groups such as sulfonates, are examples. When an electrophile is attacked by a nucleophile, the reaction proceeds through a transition state in which the electrophile and the nucleophile are both bonded to the same atom (i.e., the electrophile is partially bonded to the nucleophile and partially bonded to the leaving group).
The two species have opposite charges and are therefore attracted to one another. The following is an example reaction:CH3-CH2-Br + NaOH ⟶ CH3-CH2-OH + NaBr of Electrophilic Substitution Reaction:In an electrophilic substitution reaction (EAS), An electrophile is attracted to the electron-rich region of the attacking species, which may be a pi bond or a lone pair of electrons. An electrophile can be introduced into a molecule using a number of methods, including the use of Lewis acids or oxidizing agents.
To know more about substitution visit:
https://brainly.com/question/29383142
#SPJ11
W24 x 55 (Ix = 1350 in ) is selected for a 21 ft simple span to support a total service live load of 3 k/ft (including beam weight). Use E = 29000 ksi. Is the center line deflection of this section satisfactory for the service live load if the maximum permissible value is 1/360 of the span?
The center line deflection of the section is 0.0513 ft. As per the maximum permissible center line deflection of 0.0583 ft, the center line deflection of this section is satisfactory for the service live load.
W24 x 55 (Ix = 1350 in ) is selected for a 21 ft simple span to support a total service live load of 3 k/ft (including beam weight).
Use E = 29000 ksi.
The maximum permissible value of center line deflection is 1/360 of the span.
The maximum permissible center line deflection can be computed as;
[tex]$$\Delta_{max} = \frac{L}{360}$$[/tex]
Where, [tex]$$L = 21\ ft$$[/tex]
The maximum permissible center line deflection can be computed as;
[tex]$$\Delta_{max} = \frac{21\ ft}{360}$$$$\Delta_{max} = 0.0583\ ft$$[/tex]
The total service live load is 3 k/ft. So, the total load on the beam is;
[tex]$$W = \text{Load} \times L
= 3\ \text{k/ft} \times 21\ \text{ft}
= 63\ \text{k}$$[/tex]
The moment of inertia for the section is;
[tex]$$I_x = 1350\ in^4$$$$= 1.491 \times 10^{-3} \ ft^4$$[/tex]
The moment of inertia can be converted to the moment of inertia in SI units as follows;
[tex]$$I_x = 1.491 \times 10^{-3} \ ft^4$$$$= 0.0015092 \ \text{m}^4$$$$\Delta_{CL} = 0.0513\ ft$$[/tex]
To know more about the section, visit:
https://brainly.com/question/957452
#SPJ11
2. Draw an example of a system of equations (of conic sections) which has a. four real solutions ( 3 pts.) b. no real solutions (3 pts.) Inis Photo by Unknown Author is licensed under CC
The given system of equations satisfies the condition for having no real solutions.
On solving the system of equations, we get four real solutions (which means both x and y are real) for the system of equations. Therefore, the given system of equations satisfies the condition for having four real solutions.
b) Example of a system of equations (of conic sections) which has no real solutions:
Consider the following system of equations, consisting of two equations:
On solving the system of equations, we find that both x and y are not real, which means that the given system of equations has no real solutions.
To know more about consisting visit:
https://brainly.com/question/30321733
#SPJ11
If have 5,7 moles of gas at a pressure of 0.061 atm and at a temperature of 50.°C, what is the volume of thecontainer that the gas is in, in liters?
The volume of the container that the gas is in is approximately 2474.84 liters.
To find the volume of the container, we can use the ideal gas law equation: PV = nRT.
Given:
- Pressure (P) = 0.061 atm
- Number of moles of gas (n) = 5.7 moles
- Temperature (T) = 50.°C (which needs to be converted to Kelvin)
First, we need to convert the temperature from Celsius to Kelvin. To do this, we add 273.15 to the Celsius temperature:
Temperature in Kelvin = 50.°C + 273.15 = 323.15 K
Now we can substitute the values into the ideal gas law equation:
0.061 atm * V = 5.7 moles * 0.0821 L·atm/(mol·K) * 323.15 K
Let's simplify the equation:
0.061 atm * V = 5.7 moles * 26.576 L
To solve for V, we can divide both sides of the equation by 0.061 atm:
V = (5.7 moles * 26.576 L) / 0.061 atm
Calculating the right side of the equation:
V = 151.1652 L / 0.061 atm
Finally, we can calculate the volume of the container:
V ≈ 2474.84 L
Learn more about the ideal gas equation:
https://brainly.com/question/27870704
#SPJ11
. Which measures can be taken to reduce the welding residual
stress and residual deformation from the aspects of reasonable
design?
There are a number of steps that can be implemented from the perspectives of reasonable design to reduce welding residual stress and residual deformation.
Let check the following
Utilize a distortion-reducing joint design. This can be accomplished by using either a joint design with a symmetrical layout or one with a gradual change in cross-section.
Use a welding technique that requires little heat. The amount of thermal distortion that happens during welding will be lessened as a result of this.
Use a welding procedure that places the least amount of constraint possible on the weldment. This can be accomplished either by welding from the joint's center outwards or by employing a welding sequence that gives the weldment time to cool in between passes.
Utilize a consumable for welding with good heat conductivity. As a result, the heat will be distributed more uniformly across the weldment, reducing distortion.
Use a heat treatment after welding to remove any remaining tensions.
The weldment can be heated to a specified temperature and then progressively cooled to achieve this.
When building a weldment, it's crucial to take these precautions into account in addition to the base metal's basic qualities. It's critical to select a material that is appropriate for the purpose because some materials are more likely than others to distort.
By following these guidelines, it is possible to reduce the amount of welding residual stress and residual deformation in a weldment. This will help to improve the quality and performance of the weldment, and it will also help to extend its service life.
Here are some further suggestions for minimizing residual stress and deformation from welding:
Employ a trained welder with knowledge of reducing distortion.Apply the right welding techniques and procedures.Look closely for any indications of distortion or fracture in the weldment.Take action to fix any distortion you find.Learn more about welding residual stress
https://brainly.com/question/13039865
#SPJ4
Find a general solution to the given equation. y′′′−7y′′+16y′−12y=e^−2x+cosx
The given differential equation is y′′′−7y′′+16y′−12y=e^−2x+cosx. Let's find the general solution to the given differential equation. As it is a third-order linear non-homogeneous differential equation, we can find the general solution by solving its characteristic equation.
So, let's first find its characteristic equation. The characteristic equation of the given differential equation:
y′′′−7y′′+16y′−12y=0 is r³ - 7r² + 16r - 12 = 0.
This can be written as (r-1)(r-2)² = 0.The roots of the above equation are:r₁=1, r₂=2 and r₃=2. The repeated root "2" has a general solution (C₁ + C₂x) e^(2x). On substituting this in the differential equation, we get C₁ = -1 and C₂ = -1.Now, the general solution to the given differential equation is:
y(x) = c₁ + c₂e^2x + (c₃ + c₄x) e^(2x) + (Ax + B) e^(-2x) + (Ccos(x) + Dsin(x)).
Let's find the general solution to the given differential equation:
y′′′−7y′′+16y′−12y=e^−2x+cosx.
As it is a third-order linear non-homogeneous differential equation, we can find the general solution by solving its characteristic equation. The characteristic equation of the given differential equation:
y′′′−7y′′+16y′−12y=0 is r³ - 7r² + 16r - 12 = 0.
This can be written as (r-1)(r-2)² = 0.The roots of the above equation are:r₁=1, r₂=2 and r₃=2. The repeated root "2" has a general solution (C₁ + C₂x) e^(2x). On substituting this in the differential equation, we get C₁ = -1 and C₂ = -1.Now, the general solution to the given differential equation is:
y(x) = c₁ + c₂e^2x + (c₃ + c₄x) e^(2x) + (Ax + B) e^(-2x) + (Ccos(x) + Dsin(x)).
Here, the terms e^2x, xe^2x, e^(-2x), cos(x) and sin(x) are particular solutions that satisfy the non-homogeneous part of the given differential equation.Let's find the particular solutions to the given differential equation. The non-homogeneous part of the differential equation is e^(-2x) + cos(x).For e^(-2x), the particular solution is (Ax+B)e^(-2x).For cos(x), the particular solution is Ccos(x) + Dsin(x).On substituting the particular solutions in the given differential equation, we get:
(Ax+B)(-2)^3 e^(-2x) + (Ccos(x) + Dsin(x)) = e^(-2x) + cos(x)
Simplifying the above equation, we get:
-8Ae^(-2x) + Ccos(x) + Dsin(x) = cos(x)
Also, we have to find the values of A, B, C and D. By comparing the coefficients of e^(-2x) and cos(x) on both sides, we get A=0, B=1, C=1/2 and D=0.On substituting the values of A, B, C and D, we get the final solution to the given differential equation:
y(x) = c₁ + c₂e^2x + (c₃ + c₄x) e^(2x) + e^(-2x) + cos(x)/2.
Thus, the general solution to the given differential equation is y(x) = c₁ + c₂e^2x + (c₃ + c₄x) e^(2x) + (Ax + B) e^(-2x) + (Ccos(x) + Dsin(x))
To learn more about characteristic equation visit:
brainly.com/question/31432979
#SPJ11
Dont worry about the 1 page printout. Just the hand calculations
for #2 please
(assume saturated both below and above the GWT) and the internal angle of friction is 36º. The depth of embedment for the foundation is 3.5 ft. The GWT is located 2 ft. below the ground surface. Prov
Once you have the values for the cohesion (c'), bearing capacity factors (Nc, Nq, Nγ), and unit weight of soil (γ), you can substitute them into the formula to calculate the ultimate bearing capacity (Qb) of the foundation.
To calculate the bearing capacity of the foundation, you can use the following formula:
Qb = c'Nc + γDNq + 0.5γBNγ
Where:
Qb = Ultimate bearing capacity of the foundation
c' = Effective cohesion of the soil
Nc, Nq, and Nγ = Bearing capacity factors
γ = Unit weight of soil
D = Depth of embedment
B = Width of the foundation
In this case, since the soil is assumed to be saturated, the cohesion (c') can be considered as zero. The bearing capacity factors can be determined using empirical charts or formulas based on the angle of friction. The unit weight of soil (γ) can be obtained from soil testing.
learn more about factor from given link
https://brainly.com/question/20168177
#SPJ11
4) A meteorologist found that the rainfall in Fairfax during the first half of the month was
1 1/15 inches. At the end of the month, he found that the total rainfall for the month was 3
inches. How much did it rain in the second half of the month?
4) Write your answer as a fraction or as a whole or mixed number.
Step-by-step explanation:
To find out how much it rained in the second half of the month, we can subtract the rainfall during the first half from the total rainfall for the entire month.
Total rainfall for the month = 3 inches
Rainfall during the first half = 1 1/15 inches
To subtract these two values, we need to convert 1 1/15 to an improper fraction.
1 1/15 = (15 * 1 + 1) / 15 = 16/15
Now, let's subtract:
Total rainfall for the second half = Total rainfall - Rainfall during the first half
Total rainfall for the second half = 3 - 16/15
To subtract fractions, we need to have a common denominator. The least common multiple (LCM) of 15 and 1 is 15. Let's rewrite the equation with a common denominator:
Total rainfall for the second half = (3 * 15/15) - (16/15)
Total rainfall for the second half = 45/15 - 16/15
Now, we can subtract:
Total rainfall for the second half = (45 - 16) / 15
Total rainfall for the second half = 29/15
Therefore, it rained 29/15 inches in the second half of the month.
Pls help! WIth sequence order
Answer:
a₈₁ = -1210
Step-by-step explanation:
seq: -10, -25, -40, ...
a = -10 (first term)
d = -25 - (-10) = -15 (difference)
aₙ = a + (n-1)d
a₈₁ = -10 + (81-1)(-15)
= -10 + 80(-15)
= -10 - 1200
a₈₁ = -1210
Answer:
The answer is -1210.
Step-by-step explanation
The common difference in this sequence, -25 - -10= -15
To find the nth term, an= a1+ (n-1)d
Therefore, a81 = -10 + (81-1)(-15) = -1210
Hope this helps
Question 6 A hydrate of chromium(II) sulfate (CrSO4 XH2O) decomposes to produce 19.6% water & 80.4% AC. Calculate the water of crystallization for this hydrated compound. (The molar mass of anhydrous CrSO4 is 148.1 g/mol.) Type your work for partial credit. Answer choices: 2, 3, 4, or 5.
The water of crystallization for this hydrated compound is 1.09.
To calculate the water of crystallization for the hydrate of chromium(II) sulfate (CrSO4 XH2O), we need to use the given information that the hydrate decomposes to produce 19.6% water and 80.4% anhydrous compound (AC).
First, let's assume we have 100 grams of the hydrate compound.
From the given information, we know that 19.6 grams of the hydrate compound is water and 80.4 grams is the anhydrous compound (AC).
To find the molar mass of water, we add the molar masses of hydrogen (H) and oxygen (O), which are 1 g/mol and 16 g/mol, respectively. Therefore, the molar mass of water is 18 g/mol.
Next, we need to find the number of moles of water present in the 19.6 grams. We divide the mass of water by its molar mass:
19.6 g / 18 g/mol = 1.09 moles of water.
Since the ratio between the water and the anhydrous compound in the formula is 1:1 (CrSO4 XH2O), we can conclude that 1.09 moles of water corresponds to 1.09 moles of the anhydrous compound.
The molar mass of the anhydrous compound (CrSO4) is given as 148.1 g/mol.
Now, we can find the mass of the anhydrous compound in the 80.4 grams:
80.4 g * (148.1 g/mol / 1 mol) = 11914.24 g/mol.
To find the molar mass of the water of crystallization (XH2O), we subtract the mass of the anhydrous compound from the total mass of the hydrate:
100 g - 80.4 g = 19.6 g of water of crystallization.
Finally, we need to find the number of moles of water of crystallization. We divide the mass of water of crystallization by its molar mass:
19.6 g / 18 g/mol = 1.09 moles of water of crystallization.
Since 1.09 moles of water of crystallization corresponds to 1.09 moles of the anhydrous compound, we can conclude that the water of crystallization for this hydrated compound is 1.09.
Therefore, the answer is 1.09.
Learn more about water of crystallization:
https://brainly.com/question/30670227
#SPJ11
2. The Housing Grants, Construction and Regeneration Act 1996 (as amended) requires timely provision of payment notices. Discuss whether this legislation has had the planned effect of improving contractor's cashflow and reducing the scope for payment abuse.
The Housing Grants, Construction and Regeneration Act 1996 (as amended) has a major provision regarding payment which aimed to regulate payment behavior within the construction industry.
The act's core objective was to ensure that fair payments were made to contractors and subcontractors and to encourage better project management.
The act made it obligatory to issue payment notices by a certain date. The notice includes details such as the sum that the payer believes is due, the due date for payment, and the grounds on which payment is withheld.
The payee is required to provide a timely written notice for any payment that they feel is owed or not paid according to the terms of their contract. This notice has a similar purpose as that of the payment notice and is necessary for the payee to issue a payee notice in the event of a dispute.
Failure to provide a payment notice on time has significant consequences in the form of penalties.
Thus, the Housing Grants, Construction and Regeneration Act 1996 has helped contractors receive payment on time and has put an end to the practice of payment abuse.
It has reduced the risk of payment disputes and ensured better cash flow for contractors. The legislation's provisions are intended to provide clarity on payment issues and reduce the cost of dispute resolution.
To know more about construction visit :
https://brainly.com/question/24262346
#SPJ11
The Complete Question :
2. The Housing Grants, Construction and Regeneration Act 1996 (as amended) requires timely provision of payment notices. Discuss whether this legislation has had the planned effect of improving contractor's cashflow and reducing the scope for payment ?
The legislation has had a positive impact on improving contractor's cashflow and reducing the scope for payment abuse. However, it is important to note that while the Act provides a framework to address these issues, it may not completely eliminate them. There may still be instances where payment disputes arise or payment abuse occurs, but the Act provides mechanisms to resolve these issues more efficiently.
The Housing Grants, Construction and Regeneration Act 1996 (as amended) was implemented with the intention of improving contractor's cashflow and reducing the scope for payment abuse. Let's discuss whether this legislation has had the planned effect.
1. Timely provision of payment notices: One of the key provisions of the Act is to ensure that payment notices are provided in a timely manner. These notices inform contractors of the amount due and the date of payment. By receiving timely payment notices, contractors can better manage their cashflow and plan their finances accordingly.
2. Improving contractor's cashflow: The Act aims to address the issue of delayed payments in the construction industry. By requiring timely provision of payment notices, it helps to ensure that contractors are paid promptly for their work. This, in turn, improves their cashflow as they can rely on receiving payments on time and avoid financial strain.
3. Reducing the scope for payment abuse: The Act also aims to reduce payment abuse and protect contractors from unfair practices. For example, it introduced provisions for adjudication, which allows disputes over payments to be resolved quickly and fairly. This helps to prevent situations where contractors are unjustly denied payment or face lengthy delays in receiving what they are owed.
It is also worth mentioning that the effectiveness of the Act can vary depending on the specific circumstances and practices within the construction industry. Some contractors may still face challenges in obtaining timely payments, especially if the provisions of the Act are not strictly followed or enforced. However, the Act serves as an important tool to protect contractors and promote fair payment practices in the industry.
Learn more about legislation
https://brainly.com/question/15522014
#SPJ11
Q1 Menara JLand project is a 30-storey high rise building with its ultra-moden facade with a combination of unique forms of geometrically complex glass facade. This corporate office tower design also incorporate a seven-storey podium which is accessible from the ground level, sixth floor and seventh floor podium at the top level. The proposed building is located at the Johor Bahru city centre. (c) In your opinion, why different perspectives or views from the stakeholders are important to be coordinated systematically by the project manager during the above mentioned construction project planning stage?
Coordinating stakeholders' perspectives ensures alignment, identifies requirements, manages risks, fosters innovation, and enhances communication in construction project planning.
Different perspectives and views from stakeholders are crucial to be coordinated systematically by the project manager during the construction project planning stage for several reasons.
Alignment of Objectives: Stakeholders in a construction project can include clients, architects, engineers, contractors, local authorities, and community representatives. Each stakeholder has their own set of objectives, priorities, and concerns. Coordinating their perspectives helps ensure that these objectives are aligned and that the project meets the needs of all stakeholders. This helps avoid conflicts, delays, and costly revisions later in the project.Identifying Requirements and Constraints: Stakeholders bring their unique expertise and perspectives, which can help identify specific requirements and constraints that need to be considered in the project planning stage. For example, architects may have design requirements, contractors may have budget and schedule constraints, and local authorities may have zoning and regulatory requirements. Coordinating these perspectives allows the project manager to understand and address these factors early on, improving the overall project planning.Risk Management: Coordinating different perspectives allows the project manager to identify and address potential risks and challenges in advance. Stakeholders may have insights into specific risks related to their areas of expertise or experience. By systematically coordinating these perspectives, the project manager can develop strategies to mitigate risks, enhance safety measures, and ensure compliance with regulations.Innovation and Creativity: Involving multiple stakeholders in the project planning stage encourages the generation of innovative and creative ideas. Different perspectives can spark new approaches, technologies, and solutions. Coordinating these perspectives allows for the exploration of alternative options and promotes collaborative problem-solving, resulting in a more comprehensive and innovative project plan.Stakeholder Engagement and Communication: Coordinating different perspectives during the planning stage establishes effective communication channels between stakeholders. It fosters transparency, builds trust, and facilitates collaborative decision-making. Engaging stakeholders from the beginning ensures that their concerns and feedback are considered, leading to a sense of ownership and commitment to the project.In summary, systematically coordinating different perspectives from stakeholders during the construction project planning stage allows for alignment of objectives, identification of requirements and constraints, effective risk management, fostering innovation and creativity, and promoting stakeholder engagement and communication. This leads to a more successful and inclusive construction project.
learn more about Stakeholder coordination.
brainly.com/question/30241824
#SPJ11
AC is a diameter of OE, the area of the
circle is 289 units2, and AB = 16 units.
Find BC and mBC.
B
A
C
E. plssss hurry !!
The measure of arc BC is 720 times the measure of angle BAC.
Given that AC is the diameter of the circle and AB is a chord with a length of 16 units, we need to find BC (the length of the other chord) and mBC (the measure of angle BAC).
To find BC, we can use the property of chords in a circle. If two chords intersect within a circle, the products of their segments are equal. In this case, since AB = BC = 16 units, the product of their segments will be:
AB * BC = AC * CE
16 * BC = 2 * r * CE (AC is the diameter, so its length is twice the radius)
Since the area of the circle is given as 289 square units, we can find the radius (r) using the formula for the area of a circle:
Area = π * r^2
289 = π * r^2
r^2 = 289 / π
r = √(289 / π)
Now, we can substitute the known values into the equation for the product of the segments:
16 * BC = 2 * √(289 / π) * CEBC = (√(289 / π) * CE) / 8
To find mBC, we can use the properties of angles in a circle. The angle subtended by an arc at the center of a circle is double the angle subtended by the same arc at any point on the circumference. Since AC is a diameter, angle BAC is a right angle. Therefore, mBC will be half the measure of the arc BC.
mBC = 0.5 * m(arc BC)
To find the measure of the arc BC, we need to find its length. The length of an arc is determined by the ratio of the arc angle to the total angle of the circle (360 degrees). Since mBC is half the arc angle, we can write:
arc BC = (mBC / 0.5) * 360
arc BC = 720 * mBC
Therefore, the length of the arc BC equals 720 times the length of the angle BAC.
for such more question on measure of arc
https://brainly.com/question/25716982
#SPJ8
For the nonhamogenous system, 2a−4b+5c=8 14b−7a+4c=−28 c+3a−bb=12 Determine to ascertain that AX=b is consistent and if So express the solution in the form y=y_p+y_h
The solution to the non homogenous system of equations in the form y = y_p + y_h would be y = y_p, where y_p is the particular solution obtained by solving the system of equations.
The given system of equations is:
2a - 4b + 5c = 8 ...(1)
14b - 7a + 4c = -28 ...(2)
c + 3a - bb = 12 ...(3)
To determine if the system AX = b is consistent, we can write the system in matrix form:
A * X = b where A is the coefficient matrix, X is the column vector of variables (a, b, c), and b is the column vector of constants.
The coefficient matrix A can be formed by the coefficients of the variables a, b, and c:
A =
|2 -4 5|
| -7 14 4|
|3 -1 1|
The column vector b is formed by the constants on the right-hand side of the equations:
b =
|8|
|-28|
|12|
To determine if the system is consistent, we need to check if the determinant of the coefficient matrix A is zero. If the determinant is zero, the system is inconsistent, and if the determinant is nonzero, the system is consistent.
Calculating the determinant of A, we have:
det(A) = 2*(14*1 - 4*(-1)) - (-4)*(-7*1 - 5*(-1)) + 5*(-7*(-1) - 14*(-1))
= 2*(14 + 4) - (-4)*(-7 + 5) + 5*(-7 + 14)
= 2*18 - (-4)*(-2) + 5*7
= 36 + 8 + 35
= 79
Since the determinant of A is nonzero (79), the system AX = b is consistent. To express the solution in the form y = y_p + y_h, we can use the method of Gaussian elimination or any other suitable method to solve the system of equations.
Once we have the particular solution (y_p) and the homogeneous solution (y_h), we can write the overall solution in the form y = y_p + y_h. Since the system is consistent, it means that there is a unique solution. Therefore, the homogeneous solution (y_h) will be the zero vector.
Hence, the solution to the system of equations in the form y = y_p + y_h would be y = y_p, where y_p is the particular solution obtained by solving the system of equations.
To know more about system:
https://brainly.com/question/13729904
#SPJ11
The fish population in a certain part of the ocean (in thousands of fish) as a function of the water's temperature (in degrees celsius) is modeled by: p(x)=-2x^2+40x-72
1) What type of function is being shown?
2) What other characteristics of this type of function?
3) Determine which time will result in no fish, a population of zero.
4) use a different strategy to determine which time will result in no fish.
5) Did both strategies give you the same answer? Should they?
6) Determine which temperature will result in the largest population of fish. Explain how you determine this.
3) To determine the time at which the fish population is zero:
We have the quadratic equation: -2x^2 + 40x - 72 = 0
Using the quadratic formula: x = (-b ± √(b^2 - 4ac)) / (2a)
Substituting the values from our equation: a = -2, b = 40, c = -72
x = (-40 ± √(40^2 - 4(-2)(-72))) / (2(-2))
Simplifying further:
x = (-40 ± √(1600 - 576)) / (-4)
x = (-40 ± √(1024)) / (-4)
x = (-40 ± 32) / (-4)
So, the solutions for x (temperature) that result in a population of zero are:
x1 = (-40 + 32) / (-4) = -8 / (-4) = 2
x2 = (-40 - 32) / (-4) = -72 / (-4) = 18
Therefore, the fish population will be zero at temperature x = 2°C and x = 18°C.
6) To determine the temperature that results in the largest population of fish (maximum point):
The x-coordinate of the vertex can be found using the formula: x = -b / (2a)
In our equation, a = -2 and b = 40:
x = -40 / (2(-2)) = -40 / (-4) = 10
So, the temperature x = 10°C will result in the largest population of fish. The y-coordinate of the vertex represents the maximum population.
1) The given function is a quadratic function.
2) Characteristics of a quadratic function include:
- It is a polynomial function of degree 2.
- The graph of a quadratic function is a parabola.
- It has a vertex, which is either a minimum or maximum point, depending on the coefficient of the leading term.
- The graph is symmetric about the vertical line passing through the vertex.
- The function can have either a positive or negative leading coefficient, which determines the concavity of the parabola.
3) To determine the time at which the fish population is zero, we need to find the value of x (temperature) that makes the function p(x) equal to zero:
-2x^2 + 40x - 72 = 0
To solve this quadratic equation, we can use the quadratic formula:
x = (-b ± √(b^2 - 4ac)) / (2a)
In this case, a = -2, b = 40, and c = -72. Plugging in these values into the quadratic formula, we can find the values of x that result in a population of zero.
4) An alternative strategy to determine when the fish population is zero is by factoring the quadratic equation if possible. However, the given quadratic equation doesn't appear to be easily factorable, so using the quadratic formula is a more suitable approach.
5) Both strategies should give the same answer. Whether using the quadratic formula or factoring, the solutions for x (temperature) that result in a population of zero should be identical. The quadratic formula is a general method that works for all quadratic equations, even when factoring is not immediately apparent.
6) To determine the temperature that results in the largest population of fish, we need to find the vertex of the quadratic function. The x-coordinate of the vertex can be found using the formula:
x = -b / (2a)
In this case, a = -2 and b = 40. Plugging in these values, we can calculate the temperature (x) at which the fish population is maximized. The y-coordinate of the vertex will represent the largest population of fish.
open bard bing AI
Find the volume and surface area of the figure.
The surface area and volume of the trianglular prism are 179.2m² and 492.8m³ respectively.
How to calculate the surface area and volume of the trianglular prismarea of one trianglular face = 1/2 × 8m × 11.2m
area of one trianglular face = 44.8m²
surface area of the trianglular prism = 4 × 44.8m²
surface area of the trianglular prism = 179.2m²
Volume of triangular prism = base area × height
base area of prism = 1/2 × 8m × 11.2m
base area of prism = 44.8m²
volume of the trianglular prism = 44.8m² × 11m
volume of the trianglular prism = 492.8m³
Therefore, the surface area and volume of the trianglular prism are 179.2m² and 492.8m³ respectively.
Read more about triangular prism here:https://brainly.com/question/12591701
#SPJ1
6. (15%) Give the complexity in (g(n)) for the following five expressions ((a) to (e)). Use the simplest g(n) possible. Prove your answer for expression (a) based on the mathemat- ical definition of Big-O. (No need to give proofs for the other expressions.)
(a) √8n2+2n - 16,
(b) log(n³) + log(n²),
(c) 20-2" + 3",
(d) 7n log n + 3n15,
(e) (n+1)! +2".
(a) To determine the complexity in terms of g(n) for the expression √(8n^2 + 2n) - 16, we need to simplify it and find the dominant term.
√(8n^2 + 2n) - 16 can be rewritten as √(8n^2) * √(1 + 1/(4n)) - 16.
Ignoring the constant terms and lower-order terms, we are left with √(8n^2) = 2n.
Therefore, the complexity of expression (a) can be represented as g(n) = O(n).
Now let's discuss the complexities of the other expressions without giving formal proofs:
(b) log(n³) + log(n²):
The logarithm of a product is the sum of the logarithms. So, this expression simplifies to log(n³ * n²) = log(n^5).
The complexity of this expression is g(n) = O(log n).
(c) 20 - 2^n + 3^n:
The exponential terms dominate in this expression. Therefore, the complexity is g(n) = O(3^n).
(d) 7n log n + 3n^15:
The dominant term here is 3n^15, as it grows much faster than 7n log n. So, the complexity is g(n) = O(n^15).
(e) (n+1)! + 2^n:
The factorial term (n+1)! grows faster than the exponential term 2^n. Therefore, the complexity is g(n) = O((n+1)!).
To summarize:
(a) g(n) = O(n)
(b) g(n) = O(log n)
(c) g(n) = O(3^n)
(d) g(n) = O(n^15)
(e) g(n) = O((n+1)!)
Please note that these are simplified complexity representations without formal proofs.
Learn more about logarithm here:
https://brainly.com/question/30226560
#SPJ11
I need help pls help asap I will like pls PLEASE first second and third part please! Let T: R2→R2 be defined by T(x,y)=(x−y,x+y). Show that T is a linear transformation.
Hence, it is proved that the given transformation T is a linear transformation.
A transformation that maps a vector space V to another vector space W is known as a linear transformation. A transformation that is both additive and homogeneous is known as a linear transformation.
Furthermore, a transformation T:
V→W is called a linear transformation if T(x+y) = T(x) + T(y) and T(kx) = kT(x) for all x,y ∈ V and all k ∈ F.
Let's look at how the linear transformation T can be established in this case.
Let T: R2→R2 be defined by T(x,y)=(x−y,x+y).
Then, T is a linear transformation because it meets the following criteria:
First, for all x,y ∈ R2, T(x+y) = T(x) + T(y)
Since T(x+y) = (x + y - (x + y), x + y + x + y) = (0,2x + 2y) and T(x) + T(y) = (x - y, x + y) + (y - y, y + y) = (x - y, x + y) + (0,2y) = (x - y, 2x + 2y).
Therefore, T(x+y) = T(x) + T(y)
Second, for all x ∈ R2 and all k ∈ F, T(kx) = kT(x)T(kx) = (kx - ky, kx + ky) = k(x - y, x + y) = kT(x).
Therefore, T(kx) = kT(x).
Hence, it is proved that the given transformation T is a linear transformation.
To know more about linear transformation visit:
https://brainly.com/question/13595405
#SPJ11
A manufacturer obtain clock radios from three different subcontractors 10% from B_1, 20% from B_2, and 70% tron B_3, The defective rates for clock radios from these subcontractors are 5%,
the probability that a defective clock radio came from subcontractor B_5
The probability that cams from subcontractor, (why your now Round to the decimal places as needed)
We find that the probability that a defective clock radio came from subcontractor B_5 is 0.95, or 95%.
To calculate the probability that a defective clock radio came from subcontractor B_5, we need to consider the defective rates of the three subcontractors and their respective proportions.
Let's start by calculating the probability of a clock radio coming from subcontractor B_1.
Since B_1 provides 10% of the clock radios and has a defective rate of 5%, the probability of a defective clock radio coming from B_1 is
0.10 * 0.05 = 0.005.
Next, we calculate the probability for subcontractor B_2. B_2 provides 20% of the clock radios and has a defective rate of 5%. The probability of a defective clock radio coming from B_2 is
0.20 * 0.05 = 0.01.
Lastly, we calculate the probability for subcontractor B_3. B_3 provides 70% of the clock radios and has a defective rate of 5%. The probability of a defective clock radio coming from B_3 is
0.70 * 0.05 = 0.035.
To find the overall probability of a defective clock radio coming from subcontractor B_5, we need to subtract the probabilities we calculated so far from 1. Since there are only three subcontractors, the probability that a defective clock radio came from subcontractor B_5 is
1 - (0.005 + 0.01 + 0.035) = 0.95.
Therefore, the probability that a defective clock radio came from subcontractor B_5 is 0.95, or 95%.
Learn more about the probability from the given link-
https://brainly.com/question/13604758
#SPJ11
Consider the vectors ⇀ v ⇀ = ⟨1, 6⟩ and ⇀w⇀ = ⟨0, −4⟩. What is the magnitude of ⇀v⇀ + ⇀w⇀ expressed to the nearest tenth of a unit?
A. 10.1
B. 6.1
C. 4.0
D. 2.2
Evaluate the limit algebraically, if it exists. If the limit does not exist, explain why. If the limit is infinity (-[infinity] or +[infinity]), state it. [3x²+2 ifx-2 f(x)=x+2 if -2
The limit of f(x) as x approaches -2 is 0. This can be determined by evaluating the function at -2, which gives f(-2) = (-2) + 2 = 0. Therefore, the limit exists and equals 0.
To evaluate the limit algebraically, we need to examine the behavior of the function as x approaches -2 from both sides. As x approaches -2 from the left side, the function is defined as f(x) = 3x² + 2. Plugging in -2 for x, we get f(-2) = 3(-2)² + 2 = 12. However, when x approaches -2 from the right side, the function is defined as f(x) = x + 2. Plugging in -2 for x, we get f(-2) = (-2) + 2 = 0.
Since the function has different values as x approaches -2 from the left and right sides, the two one-sided limits do not match. Therefore, the limit as x approaches -2 does not exist. The function does not exhibit a consistent value or behavior as x approaches -2.
In this case, it is important to note that the function has a "hole" or a removable discontinuity at x = -2. This occurs because the function is defined differently on either side of x = -2. However, if we were to define the function as f(x) = 3x² + 2 for all x, except at x = -2 where f(x) = x + 2, then the limit as x approaches -2 would exist and equal 0.
Learn more about limit here: brainly.com/question/12207539
#SPJ11
Evaluate or simplify the expression without using a calculator. e^ln5x4 e^ln5x4=
The simplified expression for e^ln(5x^4) is 5x^4.
To evaluate or simplify the expression e^ln(5x^4) without using a calculator, we need to understand the properties of exponential and logarithmic functions.
Let's break down the expression step by step:
Step 1: Start with the expression e^ln(5x^4).
Step 2: Recall that ln(5x^4) represents the natural logarithm of 5x^4.
Step 3: The natural logarithm function, ln(x), is the inverse of the exponential function e^x. In other words, ln(x) "undoes" the effect of the exponential function.
Step 4: Applying the property that e^ln(x) equals x, we can simplify the expression e^ln(5x^4) as follows:
e^ln(5x^4) = 5x^4.
So, the simplified expression for e^ln(5x^4) is 5x^4.
This simplification is based on the fact that the exponential function e^x and the natural logarithm ln(x) are inverse functions of each other. When we apply e^ln(x) to any value of x, the result will always be x.
By recognizing this property and applying it to the given expression, we can simplify e^ln(5x^4) to 5x^4.
It's important to note that this simplification does not require the use of a calculator. Instead, it relies on understanding the properties of exponential and logarithmic functions and how they relate to each other.
Learn more about expression from the given link
https://brainly.com/question/1859113
#SPJ11
Calculate the percent error of a measurement procedure if it
indicates a density of
8.132 g/cm3 for a metal standard with a known density of 8.362
g/cm3
.
The percent error of a measurement procedure, with a measured density of 8.132 g/cm³ and an actual density of 8.362 g/cm³, is approximately 2.75%.
To calculate the percent error of a measurement procedure, you can use the following formula:
Percent Error = (|Measured Value - Actual Value| / Actual Value) * 100
In this case, the measured value is 8.132 g/cm³, and the actual value (known density) is 8.362 g/cm³.
Substituting these values into the formula:
Percent Error = (|8.132 g/cm³ - 8.362 g/cm³| / 8.362 g/cm³) * 100
Calculating the expression:
Percent Error = (|-0.23 g/cm³| / 8.362 g/cm³) * 100
Percent Error = (0.23 g/cm³ / 8.362 g/cm³) * 100
Percent Error ≈ 2.75%
The percent error is approximately 2.75%. It indicates the difference between the measured value and the actual value as a percentage of the actual value. In this case, the measured value is slightly lower than the actual value, resulting in a positive percent error.
To learn more about percent error visit:
https://brainly.com/question/28771966
#SPJ11
A moderator is a substance that slows down fast neutrons, increasing the likelihood that they will cause fission in 235 U. Lithium-7 has been proposed as a moderator. (a) Calculate the average number of elastic collisions with 7Li nuclei that will reduce the kinetic energy of a neutron from 2 MeV to 0.0253 eV. (b) What is the speed of a 2-MeV neutron?
On average, the neutrons incur 69 collisions with the Li⁷ moderator, to slow it down to the required Kinetic Energy.
The speed of a 2-MeV neutron is 1.54 * 10⁷ m/s.
To solve this problem, we use the basic principles of energy transfer in collisions., which work in the same way for atomic particles, as they do for larger objects.
We have the initial energy of the neutron to be 2MeV and the final energy after collisions to be 0.0253eV
E₀ = 2MeV
Eₙ = 0.0253 eV
For calculating the average number of collisions, we use the below formula:
n = (1/ξ) * ln(E₀/Eₙ)
where ξ is called the average logarithmic decrement, unique for every element.
We calculate that using another equation, which goes as follows:
ξ = 1 + (A - 1)²/2A * ln[ (A - 1)/(A + 1) ]
where A is the mass number of the moderator element.
Since we have a Lithium-7 moderator,
ξ = 1 + (7 - 1)²/14 * ln[ (7 - 1)/(7 + 1) ]
= 1 + (6)²/14 * ln[ 6/8 ]
= 1 + (36/14)*ln(3/4)
= 1 + (18/7)*(-0.287)
= 1 - 0.738
= 0.262
So, the logarithmic decrement for Lithium-7 is 0.262.
Finally, by substituting this in the number of collisions equation, we get:
n = (1/0.262)*ln(2*10⁶/0.0253)
= 3.81 * ln(79.05*10⁶)
= 3.81 * 18.185
= 69.28
≅ 69 collisions.
Now for the second part, we need the speed of a 2-MeV neutron in general.
We know that E = (1/2)mv² is the equation for Kinetic Energy.
By rearranging it, we get:
v² = 2E/m
v = √(2E/m)
So, for a neutron of energy 2MeV, whose mass is 1.67 * 10⁻²⁷, the velocity or speed is:
v = √ ( 2 * 2 * 10⁶ 1.6 * 10⁻¹⁹/1.67 * 10⁻²⁷)
= √(4 * 10¹⁴/1.67)
= √(2.39 * 10¹⁴)
= 1.54 * 10⁷ m/s
So, the velocity of the neutron is 1.54 * 10⁷ m/s.
For more on Fission Reactions and Properties,
brainly.com/question/15031433
#SPJ4
flask to the mark with water. Calculate the cencentration in tamoli. of the chemist's ironiII) bromide solution. Round your answer to 2 significant digits.
According to the given information, the chemist has an iron (III) bromide solution that he wants to know the concentration of.
In this case, we can assume that the volume of the solution added is equal to the volume of water used to dilute it. Therefore,
V1 = the total volume of the solution
= 100.0 mL (as it was diluted to the mark) Now, we need to find the final concentration of the iron (III) bromide solution in tamoli. To do this, we need to know how many moles of iron (III) bromide are present in the final solution. We can calculate this using the following formula:
n = C × V Where,
n = number of moles of iron (III) bromide
C = concentration of iron (III) bromide
V = volume of the final solution in L Now, let's calculate the number of moles of iron (III) bromide that are present in the final solution:
n = C2 × V2 Where,
C2 = concentration of iron (III)
bromide in tamoli = 0.0266 mol/L
To know more about concentration visit:
https://brainly.com/question/30862855
#SPJ11
The concentration in tamoli. of the chemist's ironiII) bromide solution is 0.03
According to the given information, the chemist has an iron (III) bromide solution that he wants to know the concentration of.
In this case, we can assume that the volume of the solution added is equal to the volume of water used to dilute it.
Therefore,
V1 = the total volume of the solution
= 100.0 mL (as it was diluted to the mark)
Now, we need to find the final concentration of the iron (III) bromide solution in tamoli.
To do this, we need to know how many moles of iron (III) bromide are present in the final solution. We can calculate this using the following formula:
n = C × V Where,
n = number of moles of iron (III) bromide
C = concentration of iron (III) bromide
V = volume of the final solution in L
Now, let's calculate the number of moles of iron (III) bromide that are present in the final solution:
n = C2 × V2 Where,
C2 = concentration of iron (III)
bromide in tamoli = 0.0266 mol/L
To know more about concentration visit:
brainly.com/question/30862855
#SPJ11
Pick the statement that best fits the Contract Family: Conventional (A201) Family of AIA documents. Is the most popular document family because it is used for the conventional delivery approach design-bid-build. Is appropriate when the owner's project incorporates a fourth prime player on the construction team. In this family the functions of contractor and construction manager are merged and assigned to one entity that may or may not give a guaranteed maximum price Is used when the owner enters into a contract with a design-builder who is obligated to design and construct the project. This document family is designed for a collaborative project delivery approach. The variety of forms in this group includes qualification statements, bonds, requests for information, change orders, construction change directives, and payment applications and certificates.
The statement that best fits the Contract Family: Conventional (A201) Family of AIA documents is: "Is the most popular document family because it is used for the conventional delivery approach design-bid-build."
The Conventional (A201) Family of AIA documents is widely used for projects that follow the conventional delivery approach known as design-bid-build. This delivery method involves separate contracts between the owner, architect/designer, and contractor. The A201 General Conditions document, which is part of this contract family, provides standard terms and conditions that govern the relationships and responsibilities of the parties involved in the project.
The Conventional (A201) Family of AIA documents is particularly popular because it is tailored for the conventional design-bid-build delivery approach. This contract family establishes the contractual framework and guidelines for the relationships between the owner, architect/designer, and contractor. The A201 General Conditions document is a key component of this contract family and outlines the rights, responsibilities, and obligations of the parties involved in the project.
Learn more about Conventional (A201) Family of AIA documents visit:
https://brainly.com/question/33797095
#SPJ11
The population of the prosperous city of Mathopia was 200,000 people in the year 2000 . In the year 2022 , the population is 1,087,308. What is the annual growth rate, r of the city during this time? [3]
The annual growth rate of Mathopia during this time period is approximately 3.62%.
To calculate the annual growth rate (r) of the city Mathopia during the years 2000-2022, we need to use the formula:
r = (final population / initial population) ^ (1 / number of years) - 1
In this case, the initial population is 200,000 in the year 2000, and the final population is 1,087,308 in the year 2022. The number of years is 2022 - 2000 = 22.
Plugging these values into the formula, we have:
r = (1,087,308 / 200,000) ^ (1 / 22) - 1
Calculating this gives us:
r ≈ 0.0362 or 3.62%
Therefore, the annual growth rate of Mathopia during this time period is approximately 3.62%.
This means that on average, the population of Mathopia has been increasing by about 3.62% each year from 2000 to 2022.
Learn more about annual growth from ;
https://brainly.com/question/30617129
#SPJ11