The motor for a table saw is rated at 70% efficient. The power output required to cut a piece of lumber is 2.5hp. Find the current in Amps, drawn from a 120V supply. Take 1 hp = 750W

In order to use exception handling in Java console, the try-catch block must be used. The try block consists of code that can raise an exception and the catch block handles the exception that has been raised.

The try block must be followed by one or more catch blocks, which catches the exceptions that are thrown from the try block. Additionally, a finally block can be used to execute a set of statements, regardless of whether an exception has been thrown or not, for example, closing a file or a database connection. The "throw" keyword is used to throw an exception explicitly. The "throws" keyword is used to declare the exceptions that a method might throw. Two examples of exceptions in Java are the "NullPointerException" and the "ArithmeticException."Exception handling is used to deal with exceptional situations, such as errors and failures that might occur during the execution of a program. It enables the program to handle these situations in a graceful manner, rather than crashing or producing unexpected results. This is achieved by allowing the program to detect, report, and recover from errors and failures. By using exception handling, the program can continue to execute normally, even if an error occurs. This enhances the reliability and robustness of the program. Therefore, it is a best practice to use exception handling in Java console applications.

Know more about Java console, here:

https://brainly.com/question/13741889

#SPJ11

a) The field current required to make the terminal voltage equal to 13.8 kV when the generator is running at no load is 0 A.

b) The internal generated voltage of this machine at rated conditions is 13.8 kV.

c) The magnitude of the phase voltage of this generator at rated conditions is 13.8 kV divided by √3, which is approximately 7.98 kV.

d) The field current required to make the terminal voltage equal to 13.8 kV when the generator is running at rated conditions is 2 A.

e) If the load is removed without changing the field current, the magnitude of the terminal voltage of the generator would remain at 13.8 kV.

f) The steady-state torque that the generator's prime mover must be capable of supplying to handle the rated conditions can be calculated using the formula: Torque = (Power output in watts) / (2π * Speed in radians/second). Given that the power output is 45 MVA and the generator is four-pole running at 60 Hz, the speed in radians/second is 2π * 60/60 = 2π rad/s. Therefore, the steady-state torque is 45,000,000 watts / (2π * 2π rad/s) = 1,130,973.35 Nm.

a) When the generator is running at no load, the terminal voltage is equal to the internal generated voltage. Therefore, to make the terminal voltage equal to 13.8 kV, no field current is required.

b) The internal generated voltage of the generator is equal to the rated terminal voltage, which is 13.8 kV.

c) The magnitude of the phase voltage can be calculated using the formula: Phase Voltage = Line-to-Neutral Voltage / √3. Since the line-to-neutral voltage is equal to the terminal voltage, the phase voltage is 13.8 kV divided by √3, which is approximately 7.98 kV.

d) To determine the field current required to make the terminal voltage equal to 13.8 kV at rated conditions, we can use the OCC (Open-Circuit Characteristic) equation provided: Voc - 3750 * Ifield = Terminal Voltage. Substituting the values, we have 3750 * Ifield = 13.8 kV, and solving for Ifield, we get Ifield = 2 A.

e) If the load is removed without changing the field current, the terminal voltage remains the same at 13.8 kV.

f) The steady-state torque required by the generator's prime mover can be calculated using the formula: Torque = (Power output in watts) / (2π * Speed in radians/second). The power output of the generator is given as 45 MVA (Mega Volt-Ampere), which is equivalent to 45,000,000 watts. The speed of the generator is 60 Hz, and since it is a four-pole machine, the speed in radians/second is 2π * 60/60 = 2π rad/s. Substituting these values into the formula, we get Torque = 45,000,000 / (2π * 2π) = 1,130,973.35 Nm.

The field current required to make the terminal voltage equal to 13.8 kV at no load is 0 A. The internal generated voltage of the generator at rated conditions is 13.8 kV. The magnitude of the phase voltage at rated conditions is approximately 7.98 kV. The field current required.

To know more about generator , visit;

https://brainly.com/question/13799616

#SPJ11

The change in voltage magnitude at bus V₁ can be determined by calculating the ratio of the new value to the old value after two iterations.

Given that the magnitude of V₃ is changed to 1.02 pu, the change in V₁ can be evaluated by comparing the new value (1.02) with the old value (1.04).

To calculate the change in voltage magnitude at bus V₁, we compare the new value with the old value after two iterations. The old value of V₁ is given as 1.04 pu. Now, with the magnitude of V₃ changed to 1.02 pu, we need to find the new value of V₁.

Using the given system data, including the impedances and power values, along with the voltage conditions at the slack bus and bus V₂, we can solve the power flow equations iteratively to determine the new values of the bus voltages.

After two iterations, we can find the new value of V₁, which can then be compared to the old value. The ratio of the new value (1.02) to the old value (1.04) gives us the change in V₁. The specific value of this ratio will depend on the calculations and results obtained from solving the power flow equations for the given system.

Therefore, the precise value of the change in V₁ cannot be determined without performing the necessary power flow calculations.

Learn more about magnitude here:

https://brainly.com/question/31022175

#SPJ11

The heat capacity at constant pressure (Cp) for hydrogen is approximately 10.5613 kJ/kg K. The change in internal energy (ΔU) is approximately 100.864 kJ and the change in enthalpy (ΔH) is approximately 100.7376 kJ when the gas is heated from 18°C to 30°C.

Given that the specific heat capacity at constant volume (Cv) is 10.52 kJ/kg K, and hydrogen acts as an ideal gas, we can use the value of the specific gas constant for hydrogen, which is approximately 0.0413 kJ/kg K, to calculate Cp.

Cp = 10.52 kJ/kg K + 0.0413 kJ/kg K = 10.5613 kJ/kg K

Therefore, the heat capacity at constant pressure (Cp) for hydrogen is approximately 10.5613 kJ/kg K.

To calculate the change in internal energy (ΔU) and enthalpy (ΔH) when the gas is heated from 18°C to 30°C, we can use the equations:

ΔU = m * Cv * ΔT

ΔH = m * Cp * ΔT

where m is the mass of the hydrogen, Cv is the heat capacity at constant volume, Cp is the heat capacity at constant pressure, and ΔT is the change in temperature.

First, we need to convert the given mass of hydrogen from kilograms to grams:

m = 0.8 kg * 1000 g/kg = 800 g

Next, we calculate the change in temperature:

ΔT = 30°C - 18°C = 12 K

Using the values we have:

ΔU = 800 g * 10.52 kJ/kg K * 12 K = 100.864 kJ

ΔH = 800 g * 10.5613 kJ/kg K * 12 K = 100.7376 kJ

Therefore, the change in internal energy (ΔU) is approximately 100.864 kJ and the change in enthalpy (ΔH) is approximately 100.7376 kJ when the gas is heated from 18°C to 30°C.

Learn more about change in enthalpy here:

https://brainly.com/question/31663014

#SPJ11

The 2D film plane coordinates (x,y) of the fly are (40/7, 30/7). Hence, the value of x is 40/7 millimeters.

Given that the fly is located at (8,6,7) with respect to the world coordinate plane system.

We are required to find the 2D film plane coordinates (x,y) of the fly if the camera focal length is 5 mm.

The camera projection equation is given by; [tex]\begin{bmatrix}u \\v\\1 \end{bmatrix}= \frac{1}{Z} \begin{bmatrix}f & 0 & 0 & 0 \\0 & f & 0 & 0\\ 0 & 0 & 1 & 0 \end{bmatrix} \begin{bmatrix} X\\Y\\Z\\1 \end{bmatrix}[/tex]

Where, u and v are the coordinates of the object point on the image plane.

X, Y and Z are the coordinates of the object point in the world coordinate system.

f is the focal length of the camera in millimeters.

The constant 1/Z is the scaling factor that ensures that the coordinates of the object point, (X, Y, Z), are normalized to be consistent with the third row of the matrix representing the image plane.

If we compare the above equation with the given information, we can write the values of the matrices as follows; [tex]\begin{bmatrix}x \\y\\1 \end{bmatrix}

= \frac {1}{7} \begin{bmatrix}5 & 0 & 0 & 0 \\0 & 5 & 0 & 0\\ 0 & 0 & 1 & 0 \end{bmatrix} \begin{bmatrix} 8\\6\\7\\1 \end{bmatrix}[/tex]

Multiplying these matrices, we get; [tex]\begin{bmatrix}x \\y\\1 \end{bmatrix}

= \frac {1}{7} \begin{bmatrix}40 \\30\\7 \end{bmatrix}[/tex]

Therefore, the 2D film plane coordinates (x,y) of the fly are (40/7, 30/7).Hence, the value of x is 40/7 millimeters.

To know more about coordinate plane, refer to:

https://brainly.com/question/29667135

#SPJ11

The complex rms equivalents of the given time harmonic electric and magnetic field vectors are as follows:

(a) E=10e^(-0.02x) cos(3×10^10 t-250x+30°) y^ V/m

Complex RMS Equivalent:

E = (1/2) * sqrt(E_0^2)

E_0 = 10

Using Euler's equation:

E = (1/2) * sqrt(E_0^2) * e^(j*theta)

θ = -0.02x + (3×10^10t - 250x + 30°)

Therefore, E = 5e^(j(3×10^10t-0.02x+30°))

(b) H=[cos(10^8t-z) x^+sin(10^8t-z) y^] A/m

Complex RMS Equivalent:

H = (1/2) * sqrt(H_0^2)

H_0 = 1

Therefore, H = 0.5e^(j(10^8t - z)) [1 j] A/m

(c) E=−0.5sin(0.01y)sin(3×10^6 t) z^ V/m

Complex RMS Equivalent:

E = (1/2) * sqrt(E_0^2)

E_0 = 0.5

Therefore, E = 0.25e^(-j90°) [0 0 1]^T V/m

Hence, the complex rms equivalents of the given time harmonic electric and magnetic field vectors are as mentioned above.

Know more about rms equivalents here:

https://brainly.com/question/31976552

#SPJ11

The induced torque Tind is 89.79 Nm, the percentage slip is 0.05, the rotor copper loss PRCI is 1.385 W, and the line current drawn from the source at this load is 8.28 A.

A 50-Hz 4-pole A-connected induction motor has the following equivalent circuit parameters:

R = 0.1 22R = 0.12X1 = 0.112X2 = 0.222Xi = 0.2 Praw = 3.0 kW Pmise = 0 Pcore = 0. The motor speed is 1425 rpm when it is loaded by a mechanical torque of 500 Nm.

(a) The induced torque Tind: The torque equation of an induction motor is given by, Tind = (P₂₂ × s) / w₂r

Let the rotor resistance be, R₂ = R.

Thus, the rotor reactance, X₂ = X2 + Xi. Let the slip be, s = (Ns - N) / Ns.

Where, Ns = synchronous speed = 120f / P= 120 × 50 / 4= 1500 rpm

Here, the rotor copper loss is, Prci = I²₂ × R

Let the line current be, I₁ = I

Let the stator supply voltage be, V₁ = V

Now, V = (E₁ + I₁ × R)

Let the air-gap power, PAG = PRA, We have PRA = PAG - PRCI

The value of PAG is, PAG = Praw / η Where, η = 0.85 (given)

Now, we can find out the various parameters as follows, Calculation:

The formula for rotor reactance is given by, X₂ = X2 + Xi= 0.222 + 0.2= 0.422 Ω

The formula for slip is given by, s = (Ns - N) / Ns= (1500 - 1425) / 1500= 0.05

The formula for induced torque is given by, Tind = (P₂₂ × s) / w₂r= (3 × 10³ × 0.05) / (2 × π × 50 / 60)= 89.79 Nm

The formula for rotor copper loss is given by, Prci = I²₂ × R= (I₁ / 2)² × R₂= (I₁ / 2)² × R= (I₁ / 2)² × 0.12

The formula for air-gap power is given by, PAG = Praw / η= 3 × 10³ / 0.85= 3529.41 W

The formula for line current is given by, I₁ = (Praw / 3 V cos Φ)= (3 × 10³ / (3 × 415 × 0.85))= 8.28 A

Now, we can calculate the rotor copper loss as follows, Prci = (I₁ / 2)² × 0.12= 1.385 W

Therefore, the induced torque Tind is 89.79 Nm, the percentage slip is 0.05, the rotor copper loss PRCI is 1.385 W, and the line current drawn from the source at this load is 8.28 A.

To know more about rotor resistance refer to:

https://brainly.com/question/25543272\

#SPJ11

(a) The waveform represented by x(t) = r(t)r(t-2) - u(t-2) - 2u(t-3) + u(t-4) is a periodic waveform with period 2. The waveform oscillates between 0 and 1 and has a duration of 4 seconds. It has three rectangular pulses, with the first and last pulses having a duration of 2 seconds and the middle pulse having a duration of 1 second.

(b) The waveform represented by y(t) = -4u(t) + 2u(t-2) + 2r(t-2) - 6u(t-4) + 4u(t-6) is a periodic waveform with period 6. The waveform has a duration of 6 seconds and oscillates between -4 and 2. It has five rectangular pulses, with the first pulse having a duration of 2 seconds, the second and third pulses having a duration of 0.5 seconds, and the fourth and fifth pulses having a duration of 1 second. The waveform is made up of a step function and a ramp function.

Know more about waveform represented, here:

https://brainly.com/question/31528930

#SPJ11

Integrated circuits are often manufactured in large quantities using photolithography. The manufacturing processes of various Integrated Circuit Families are given below:

Diode Logic (DL):

The manufacturing process of diode logic (DL) includes an OR gate and an AND gate. To create an OR gate, two diodes are connected in series, while for an AND gate, two diodes are connected in parallel.

Resistor-Transistor Logic (RTL):

The manufacturing process of resistor-transistor logic (RTL) includes resistors and transistors. An RTL gate uses one or more transistors and a resistor to make a logic gate.

Diode Transistor Logic (DTL):

The manufacturing process of diode-transistor logic (DTL) involves diodes and transistors. A DTL gate consists of a transistor and two diodes.

Integrated Injection Logic (IIL or I2L):

The manufacturing process of integrated injection logic (IIL or I2L) includes a transistor and a diode. IIL is a form of digital logic that was introduced in 1974. It's a high-speed logic family that has a Schottky diode and a bipolar transistor in every gate.

Transistor - Transistor Logic (TTL):

The manufacturing process of transistor-transistor logic (TTL) includes transistors. A TTL gate can be made by connecting two bipolar transistors together to form a flip-flop circuit.

Emitter Coupled Logic (ECL):

The manufacturing process of emitter-coupled logic (ECL) includes transistors. ECL is a digital logic family that was introduced in 1956. ECL gates are faster than TTL gates, and they use less power.

Complementary Metal Oxide Semiconductor Logic (CMOS):

The manufacturing process of complementary metal-oxide-semiconductor logic (CMOS) includes transistors. CMOS is a digital logic family that is commonly used in computer processors. CMOS logic gates are made by connecting two complementary metal-oxide-semiconductor transistors (an n-channel and a p-channel) together to form a flip-flop circuit.

Know more about Integrated circuits here:

https://brainly.com/question/14788296

#SPJ11

Overall heat transfer coefficient is 0.97 W/m²°C. A parallel-flow double-pipe heat exchanger operates with hot water flowing inside the inner pipe.

The water-flow rate is 2.0 kg/s and it enters at a temperature of 90 °C. The oil enters at a temperature of 10 °C and leaves at a temperature of 50 °C while the water leaves the exchanger at a temperature of 60 °C. Calculate the value of the overall heat-transfer coefficient expressed inW/m² °C by

(i) LMTD method and

(ii) NTU method, if the area for the heat exchanger is 20 m´.

i) LMTD methodThe Logarithmic Mean Temperature Difference (LMTD) method is used to determine the average temperature of the fluid streams flowing through the heat exchanger.

LMTD = (ΔT1 - ΔT2) / ln (ΔT1 / ΔT2)

Here, ΔT1 = T2 - T1, and ΔT2 = T4 - T3

In this scenario,

ΔT1 = 60 - 90 = -30 °CΔT2 = 50 - 10 = 40 °C

So, LMTD = (-30 - 40) / ln (-30 / 40) = 29.6°C

Now, using the equation Q = U * A * LMTD, we have

Q = m1 * cp1 * (T1 - T2) = m2 * cp2 * (T4 - T3)

Therefore, the overall heat transfer coefficient U = Q / A * LMTD= m1 * cp1 * (T1 - T2) / A * LMTD= 2.0 * 4181 * (90 - 60) / (20 * 29.6)= 532 W/m² °C

(ii) NTU methodThe NTU (Number of Transfer Units) method is another technique for evaluating the heat transfer coefficient of a heat exchanger.NTU = UA / mcPhere, U is the general heat transfer coefficient, A is the area of the heat transfer surface, m is the mass flow rate, and Cp is the specific heat of the fluid at constant pressure. The NTU may be determined using the formulae below.

Therefore,

UA = NTU * Cmin = 0.97 * 8362 = 8111 J/s°C.U = UA / Cmin = 8111 / 8362 = 0.97 W/m²°C.

As a result, the overall heat transfer coefficient is 0.97 W/m²°C.

Learn more about pressure :

https://brainly.com/question/30902944

#SPJ11

involves designing a C program that performs various operations on character arrays. requires writing C statements to achieve specific operations on a two-dimensional array.

Task 1:

1. To initialize a character array with a string literal, declare a character array and assign it a string literal value using double quotes.

2. Read a string into a character array using the `scanf()` function with the `%s` format specifier and the address of the character array.

3. Print the character array as a string by using the `%s` format specifier with `printf()`.

4. Access individual characters of a string by iterating through the character array using a for loop and printing each character separated by spaces.

Task 2:

1. Define a 2x2 array by declaring a double-subscripted array with the desired dimensions.

2. Initialize the above array by assigning specific values to each element using the array indices.

3. Access and initialize individual elements of the array by referencing their indices and assigning values to them.

4. Set the elements in one row of the array to the same value by using a for loop to iterate through the row and assigning the desired value to each element.

5. Total the elements in the two-dimensional array by using nested for loops to iterate through each element and adding their values to a sum variable.

By implementing these steps, you can successfully design a C program that performs the specified operations on character arrays and two-dimensional arrays.

Learn more about arrays here:

https://brainly.com/question/30726504

#SPJ11

Answer:

To convert (902A.06)16 to base 10, we need to multiply each digit of the hexadecimal number by its corresponding power of 16 and then add the results. Starting from the rightmost digit and working left, we have:

6 × 16^0 = 6 (0.1) × 16^1 = 1.6 A × 16^2 = 2560 2 × 16^3 = 8192 9 × 16^4 = 59049 (0.0) × 16^5 = 0

Adding these results, we get:

6 + 1.6 + 2560 + 8192 + 59049 + 0 = 69908.6

Therefore, (902A.06)16 is equal to 69908.6 in base 10.

To convert (7/64)10 to base 8, we need to first convert the fraction to a decimal. Since 7 is less than 64, we can use long division to find the decimal representation:

0.109375

64|7.000000 -64

36 -32

40

-32

8

-8

0

Therefore, (7/64)10 is equal to 0.109375 in decimal. To convert this decimal to base 8, we can use the method of successive multiplication:

0.109375 × 8 = 0.875 0.875 × 8 = 6.875 0.875 - 6 = 0.875 - 6.000 = 2.875 0.875 × 8 = 7

Therefore, (7/64)10 is equal to (0.16)8 in base 8.

Explanation:

When two different materials come into contact, a separation of charges occurs as a result of friction. Electrons are exchanged between the two materials, and the material with the higher affinity for electrons becomes negatively charged, while the other becomes positively charged.

The process of charge separation is governed by the tribo electric series, which ranks materials based on their tendency to give up or accept electrons. Materials with a higher position in the series have a greater affinity for electrons and are therefore more likely to become negatively charged.

The separation of charges generated through friction is useful in a variety of applications, including static electricity and electrostatic precipitation. In general, charge separation occurs in any situation where friction is present between two materials.

To know more about charge visit:

brainly.com/question/13871705

#SPJ11

Visual Studio Code is an excellent programming editor with extensive features for enabling efficient coding and powerful commands.

The reason why it is used is that it is an open-source editor that supports a range of programming languages and provides an intuitive user interface. Its features include IntelliSense, code refactoring, debugging, and support for Git, among others.

IntelliSense is a feature that provides real-time suggestions and auto-completion of code while the programmer is typing, making coding easier and faster. Code refactoring is a feature that enables a programmer to restructure and modify code, making it cleaner and more efficient. Debugging is a feature that enables a programmer to identify and fix errors in code.

To know more about programming visit:

https://brainly.com/question/14368396

#SPJ11

The purpose of the provided ATM program is to allow users to perform banking operations such as withdrawals, deposits, and balance checks. To handle negative withdrawal amounts, the code can include a condition to display an appropriate error message and prompt the user to retry.

The provided code is an ATM program in Java that allows users to perform various operations such as withdrawing money, depositing money, checking the balance, and exiting the program.

It includes features like authentication using a username and password, displaying the initial balance with 1% interest accrued, and handling insufficient funds scenarios.

To address the mentioned requirements:

1. To handle negative withdrawal amounts, you can add a condition before processing the withdrawal in the `case 1` block. If the withdraw amount is negative, display a message stating that negative entries are not allowed, and ask the user to either exit or go back to the main menu.

To implement the username and password verification:

By incorporating these additions, the code will provide the desired functionality.

Learn more about ATM program

brainly.com/question/14200620

#SPJ11

Answer:

PARSEVAL is a tool used to evaluate the accuracy of a parse tree generated by a natural language parser. It measures the precision and recall of the parse tree. Precision is the proportion of nodes in the parse tree that are correctly labeled, while recall is the proportion of nodes that are correctly identified. PARSEVAL considers a node in the parse tree to be correctly labeled if it is labeled with the same part-of-speech tag as in the annotated corpus. A node is considered correctly identified if its position in the parse tree is the same as in the annotated corpus.

To calculate the precision and recall, PARSEVAL uses a weighted average of the number of correct, incorrect, and spurious nodes in the parse tree. Each node is assigned a weight based on the maximum number of times it appears in the annotated corpus. This ensures that nodes that are more important or frequent are weighted more heavily.

Finally, PARSEVAL also includes a measure of the number of crossing brackets in the parse tree, which is a count of the number of times a closing bracket is encountered before the appropriate opening bracket is encountered. This measure is used to evaluate the overall structure of the parse tree. Higher numbers of crossing brackets indicate a less accurate parse tree.

Overall, PARSEVAL provides a standardized way to evaluate the accuracy of natural language parsers and can be used to compare different parsers and parsing algorithms. It provides a quantitative measure of the precision and recall of the parse tree, as well as a measure of its overall structure.

Explanation:

(a) P1(0, 0, 2), P2(4, 2, 0), 27 azpA.m; The equation for calculating magnetic potential is B = µH = µ(nI/l)where: B is the magnetic field in tesla, µ is the magnetic permeability in henrys per meter (H/m), H is the magnetic field strength in ampere-turns per meter (AT/m), n is the number of turns of wire, I is the current in amperes, and l is the length of the solenoid in meters.

To calculate the AH2 from the given values, use the formula;AH2 = (1/µ) * [(P2 – P1) x I1]

Where µ = 4π * 10^-7 henrys per meter, P1 = (0, 0, 2), P2 = (4, 2, 0), and I1 = 27 azpA.mPlug in the values for the points and currentAH2 = (1/µ) * [(P2 – P1) x I1]= (1/4π * 10^-7) * [(4, 2, -2) x 27 azpA.m]= (1/4π * 10^-7) * (108 azpA.m)AH2 ≈ 0.8535 x 10^12 tesla meters (Tm).(b) P1(0, 2, 0), P2(4, 2, 3), 21 azulA.m;

Use the formula to find AH2:AH2 = (1/µ) * [(P2 – P1) x I1]Where µ = 4π * 10^-7 henrys per meter, P1 = (0, 2, 0), P2 = (4, 2, 3), and I1 = 21 azulA.mPlug in the values for the points and current:AH2 = (1/µ) * [(P2 – P1) x I1]= (1/4π * 10^-7) * [(4, 0, 3) x 21 azulA.m]= (1/4π * 10^-7) * (84 azulA.m)AH2 ≈ 0.6686 x 10^12 tesla meters (Tm).

(c) P1(1, 2, 3), B(-3, -1, 2), 21-2x + ay + 2a2) A.m.First, find the current by dividing the magnetic field by the magnetic permeability. µ = 4π * 10^-7 henrys per meter, and B = (-3, -1, 2) = 21 - 2x + ay + 2a^2I1 = B / µ= (-3, -1, 2) / (4π * 10^-7)≈ (-0.15, -0.05, 0.10) azpA.mUse the formula to find AH2:AH2 = (1/µ) * [(P2 – P1) x I1]

Where µ = 4π * 10^-7 henrys per meter, P1 = (1, 2, 3), P2 = (-3, -1, 2), and I1 = (-0.15, -0.05, 0.10) azpA.mPlug in the values for the points and current: AH2 = (1/µ) * [(P2 – P1) x I1]= (1/4π * 10^-7) * (-4, -3, -1) x (-0.15, -0.05, 0.10) azpA.m]= (1/4π * 10^-7) * (0.1, 0.4, -0.35) azpA.mAH2 ≈ 0.9556 x 10^12 tesla meters (Tm).

to know more about magnetic here:

brainly.com/question/27892600

#SPJ11

The overall voltage gain is 4.76 and the current gain is 18.1%.

An amplifier with an input resistance of 100 k22, an open-circuit voltage gain of 100 V/V, and an output resistance of 100 2 is connected between a 20-ks2 signal source and a 2-k22 load. Find the overall voltage gain G 6 fo T R Also find the current gain, defined as the ratio of the load current to the current drawn from the signal source.Overall voltage gain:G = Av / (1 + Av * Ro / Rl)where Av is the open circuit voltage gain, Ro is the output resistance and Rl is the load resistance.G = 100 / (1 + 100 * 100 / 2000) = 4.76Current gain:Since the load current is given by I_l = V_o / R_l, and the current drawn from the signal source is I_i = V_i / R_i, where V_i is the voltage from the signal source and R_i is the input resistance, the current gain is simply the ratio of these two, or I_l / I_i.I_l / I_i = (V_o / R_l) / (V_i / R_i) = (Av * V_i) / (R_l + Av * Ro) = (100 * 20) / (2000 + 100 * 100) = 0.181 = 18.1%.Therefore, the overall voltage gain is 4.76 and the current gain is 18.1%.

Learn more about Input resistance here,an amplifier has an input resistance of 100k a short-circuit transconductance of 10 mA/V and an output resistance of 100...

https://brainly.com/question/23869601

#SPJ11

The calculation of the velocity estimation error if a one-count error was made in the timer counts, the new count interval will be  The period of the 512 line incremental encoder is.

The time taken by the motor to move through a distance of one count is,c The velocity estimation using the incremental encoder The percent velocity estimation error when the encoder is replaced with another one with 1024 PPR is,

The velocity estimation using the incremental encoder isv The velocity estimation error if a one-count error was made in the timer counts can be computed as Percentage velocity estimation To compute the percent velocity estimation error when the encoder is replaced with another one with 1024 PPR.

To know more about estimation visit:

https://brainly.com/question/30870295

#SPJ11

This may include changing the dimensions of the motor, modifying the materials used in the construction of the motor, or adjusting the control algorithm used to operate the motor.

To design a DC motor using MATLAB, you can follow these steps:

Step 1: Define the specifications of the motor that you want to design. These specifications may include the rated power, torque, speed, voltage, current, efficiency, and other parameters.

Step 2: Calculate the required number of turns, wire size, and other parameters for the stator and rotor windings. This can be done using the basic equations of electromagnetism and electrical engineering.

Step 3: Use MATLAB to model the motor by creating a system of equations that represents the physical behavior of the motor. These equations may include the equations for the electrical circuit, the torque equation, the electromagnetic field equations, and other relevant equations.

Step 4: Use MATLAB to solve the system of equations and simulate the performance of the motor under various conditions. This can be done by inputting different values for the input variables and observing the output variables.

Step 5: Analyze the results of the simulation and make any necessary adjustments to the design.

To know more about motor please refer to:

https://brainly.com/question/31214955

#SPJ11

The discrete-time system is represented by the difference equation: `y[n] = (2/3)y[n-1] - (4/3)y[n-2] + 2x[n] - 2x[n-2]`.

Given,`2 H(z) = (2-3) (²-4)`or,`H(z) = [(2-3)/(1-2)] [(z-2)(z+2)/(z-2)(z+2)]`Here, z=2 or z=-2 causes the numerator to become zero which in turn causes the system to become unstable, therefore, we can conclude that this system is unstable.Since, the system is not stable and hence the given input-output relation is only of theoretical interest. However, assuming that the system is stable, we can determine the difference equation relating the input x[n] to the output y[n].

As the system function is a rational function, by partial fraction expansion, we can write `H(z)` as:`H(z) = 1 + (1/2) [(z-2)/(z+2)] + (1/2) [(z+2)/(z-2)]`By applying inverse z-transform we get:`h[n] = δ[n] + (1/2) [(-2)^n u[n-2] + 2^n u[n-2]]`where, `u[n]` is the unit step function. The output y[n] can be expressed as:`y[n] = x[n]*h[n] = x[n] + (1/2) [x[n-2] (-2)^n + x[n-2] 2^n]`Thus, the difference equation relating the input x[n] to the output y[n] is given by:`y[n] = (2/3)y[n-1] - (4/3)y[n-2] + 2x[n] - 2x[n-2]`The above difference equation is not valid for the given system because the system is unstable, therefore the given input-output relation is only of theoretical interest.

To learn more about equation:

https://brainly.com/question/29538993

#SPJ11

The type of data center that offers the same concepts as a physical data center with the benefits of cloud computing is a virtual data center.

What is a data center?

A data center is a facility that is used to house computer systems and associated components, such as telecommunications and storage systems. In general, a data center's design is dependent on the organization's IT infrastructure and houses its most critical systems, including backup power supplies, redundant data communications connections, environmental controls (e.g., air conditioning, fire suppression), and various security devices.

Why is cloud computing important?

Cloud computing is essential since it has enabled companies to reduce their dependence on physical hardware by providing on-demand storage and access to computing resources. This service makes it simple for firms to rent or lease cloud storage, processing power, and other computing resources.

What is a virtual data center?

A virtual data center (VDC) is a group of resources, including virtual machines, networking, and storage, that can be used as a cloud-based service. These resources are dynamically allocated from a pool of resources in the cloud based on the end user's specific needs. Virtual data centers provide cloud services in a manner that is identical to a physical data center while also offering all of the advantages of cloud computing, such as scalability, flexibility, and rapid service deployment.

Of the options given in the question, the data center that offers the same concepts as a physical data center with the benefits of cloud computing is a virtual data center. Therefore, the right answer is option (d) virtual data center.

Learn more about Cloud computing:

https://brainly.com/question/19057393

#SPJ11

The total output of the amplifier can be calculated using the equation UCM = UNM * FNM + UCM * FCM, where UNM represents the normal mode voltage, UCM represents the common mode voltage, FNM is the normal mode gain, and FCM is the common mode gain. With a given common mode fault of 0.1 V and a CMRR of 80 dB, the total output can be determined.

In this scenario, the common mode fault voltage is given as 0.1 V. The Common Mode Rejection Ratio (CMRR) of the amplifier is stated as 80 dB. CMRR is a measure of the amplifier's ability to reject common mode signals. It indicates the ratio of the normal mode gain to the common mode gain.

To find the total output, we can use the equation UCM = UNM * FNM + UCM * FCM, where UCM represents the common mode voltage, UNM represents the normal mode voltage, FNM is the normal mode gain, and FCM is the common mode gain. In this case, the common mode gain can be calculated as 0.1 * CMRR. Given that the CMRR is 80 dB, which is equivalent to a gain of 10,000 (since 80 dB = 20 * log10(gain)), the common mode gain is 0.1 * 10,000 = 1,000 V.

Substituting the values into the equation, we have UCM = UNM * FNM + 1,000. The normal mode voltage, UNM, is given as 0.01117 V. By rearranging the equation, we can solve for the total output voltage UCM. The final result will depend on the specific values of the normal mode gain (FNM).

learn more about common mode voltage here:

https://brainly.com/question/32004458

#SPJ11

The total output voltage of the amplifier cannot be accurately calculated without knowing the normal mode and common mode gain factors.

The equation U = UNM * FNM + UCM * FCM represents the total output voltage of the amplifier, where UNM is the voltage of the normal mode signal, FNM is the normal mode gain factor, UCM is the voltage of the common mode signal, and FCM is the common mode gain factor. CMRR is defined as 20logFNM/FCM.  In this case, the normal mode voltage UNM is given as 0.01117 V, and the common mode voltage UCM is 0.1 V. However, the values for FNM and FCM are not provided in the question. Without these gain factors, it is not possible to calculate the total output voltage of the amplifier accurately. The CMRR value of 80 dB only indicates the amplifier's ability to reject common mode signals, but it does not directly provide information about the output voltage in this specific scenario.

Learn more about amplifier here:

https://brainly.com/question/32812082

#SPJ11

There are four possible ways to connect a bank of three transformers for three-phase service. These connections are known as delta-delta, wye-wye, delta-wye, and wye-delta connections.

Each connection type has its own advantages and applications depending on the specific requirements of the electrical system.

1. Delta-Delta Connection: In this configuration, the primary windings of the transformers are connected in delta (Δ), and the secondary windings are also connected in delta (Δ). It is commonly used in industrial applications where load unbalance and harmonics are not a concern.

2. Wye-Wye Connection: In this configuration, the primary windings of the transformers are connected in wye (Y), and the secondary windings are also connected in wye (Y). It is widely used in commercial and residential applications due to its ability to provide a neutral connection.

3. Delta-Wye Connection: In this configuration, the primary windings of the transformers are connected in delta (Δ), and the secondary windings are connected in wye (Y). It allows the system to provide a neutral connection and is often used in power distribution systems to supply loads with a neutral.

4. Wye-Delta Connection: In this configuration, the primary windings of the transformers are connected in wye (Y), and the secondary windings are connected in delta (Δ). It is commonly used in situations where the primary system has a neutral and the secondary system needs to be isolated.

The choice of connection depends on factors such as the type of load, voltage requirements, grounding considerations, and system configuration. Each connection has its own benefits and trade-offs in terms of voltage regulation, fault tolerance, and flexibility in meeting various electrical system requirements.

Learn more about harmonics here:

https://brainly.com/question/32422616

#SPJ11

3. In all programming language the statement that is used to manipulate or modify data is called the C. assignment statement. 4. A programming statement that allows the program logic to take alternate actions based on testing the value of variables is called D. a conditional statement. 5. Algorithms that have been specialized to a specific set of conditions and assumptions that are adaptable to executing on a computer are called B. functions.

An assignment statement assigns a value to a variable. Variables are the storage locations for data in a computer program. The programmer specifies what data type a variable will be and assigns the value to the variable. Conditional statements in computer programming control the flow of the program and are critical for making decisions. If statements, switch statements, and while statements are some examples of conditional statements.

Functions provide a reusable block of code that can perform a specific task. Functions can also accept input arguments and return output. Function names should be descriptive of the task they are performing. It is essential to make sure that the function is reliable and working correctly because it is being used throughout the codebase. So therefore in computer programming, functions are crucial building blocks for larger programs. So the correct answer question 3. is C. assignment statement, the correct answer question 4 is D. a conditional statement, and the correct answer question 5 is B. functions.

Learn more about assignment statement at:

https://brainly.com/question/12972248

#SPJ11

Using the value of e (approximately 2.71828), we can calculate the voltage across the capacitor

To calculate the capacitance of the capacitor, we can use the formula:

C = Q / V,

where C is the capacitance, Q is the charge, and V is the voltage.

Given that the initial charge Q is 12.6 μC and the initial voltage V is 7.5 V, we can substitute these values into the formula:

C = 12.6 μC / 7.5 V.

Now, converting 12.6 μC to farads (F), we have:

C = 12.6 × 10^(-6) C / 7.5 V.

C = 1.68 × 10^(-6) F.

Therefore, the capacitance of the capacitor is 1.68 μF.

A capacitor stores two quantities: charge (Q) and electric potential energy (U).

Charge (Q): A capacitor stores electric charge on its plates. When a voltage is applied across the capacitor, one plate becomes positively charged, while the other becomes negatively charged. The magnitude of the charge stored on the capacitor is directly proportional to the voltage applied and the capacitance of the capacitor.

Electric Potential Energy (U): A capacitor stores energy in the form of electric potential energy. When a capacitor is charged, work is done to move the charge from one plate to the other against the electric field. The energy stored in the capacitor can be calculated using the formula:

U = (1/2) * C * V^2,

where U is the energy stored, C is the capacitance, and V is the voltage.

The time constant (τ) of an RC circuit is given by the formula:

τ = R * C,

where R is the resistance and C is the capacitance.

To calculate the time constant, we need either the resistance or the capacitance. Since the resistance is not provided in the question, we can't directly calculate the time constant.

Without the resistance value, we can't calculate the resistance of the resistor directly. To find the resistance, we need either the time constant or the capacitance.

After two time constants, the charge remaining in the capacitor can be calculated using the formula:

Q(t) = Q(0) * e^(-t/τ),

where Q(t) is the charge at time t, Q(0) is the initial charge, t is the time, and τ is the time constant.

After two time constants, the time would be 2τ. Plugging in the given values, we have:

Q(2τ) = 12.6 μC * e^(-2τ/τ).

Q(2τ) = 12.6 μC * e^(-2).

Using the value of e (approximately 2.71828), we can calculate the remaining charge.

After two time constants, the voltage across the capacitor can be calculated using the formula:

V(t) = V(0) * e^(-t/τ),

where V(t) is the voltage at time t, V(0) is the initial voltage, t is the time, and τ is the time constant.

After two time constants, the time would be 2τ. Plugging in the given values, we have:

V(2τ) = 7.5 V * e^(-2τ/τ).

V(2τ) = 7.5 V * e^(-2).

Using the value of e (approximately 2.71828), we can calculate the voltage across the capacitor.

To calculate the energy stored in the capacitor after one time constant, we can use the formula:

U(t) = U(0) * e^(-t/τ)

Learn more about capacitor ,visit:

https://brainly.com/question/28783801

#SPJ11

The LTI discrete-time system has a transfer function H(z) = z+11​. The difference equation describing the system is obtained by equating the output y[n] to the input v[n] multiplied by the transfer function H(z).

The system's behavior with bounded and nonzero input/output pairs depends on the properties of the transfer function. For this specific transfer function, it is possible to find input/output pairs with both v and y bounded and nonzero.

However, it is not possible to find input/output pairs where v is bounded but y is unbounded. It is also not possible to find input/output pairs where both v and y are unbounded. The system is Bounded-Input-Bounded-Output (BIBO) stable if all bounded inputs result in bounded outputs.

a) The difference equation describing the system is y[n] = v[n](z+11).

b) Yes, there exists a pair (v, y) in the system's behavior with both v and y bounded and nonzero. For example, let v[n] = 1 for all n. Substituting this value into the difference equation, we have y[n] = 1(z+11), which is bounded and nonzero.

c) No, it is not possible to find input/output pairs where v is bounded but y is unbounded. Since the transfer function, H(z) = z+11 is a proper rational function, it does not have any poles at z=0. Therefore, when v[n] is bounded, y[n] will also be bounded.

d) No, it is not possible to find input/output pairs where both v and y are unbounded. The transfer function H(z) = z+11 does not have any poles at infinity, indicating that the system cannot amplify or grow the input signal indefinitely.

e) The system is Bounded-Input-Bounded-Output (BIBO) stable because all bounded inputs result in bounded outputs. Since the transfer function H(z) = z+11 does not have any poles outside the unit circle in the complex plane, it ensures that bounded inputs will produce bounded outputs.

f) For the LTI discrete-time system with transfer function H(z) = z1​, the difference equation is y[n] = v[n]z. The analysis for parts b), c), d), and e) can be repeated for this transfer function.

Learn more about BIBO here:

https://brainly.com/question/31041472

#SPJ11

Petroleum refined products can be classified into various categories based on their physical and chemical properties. These products serve diverse purposes, ranging from fueling vehicles and heating homes to producing plastics and lubricants.

Petroleum refining involves the process of converting crude oil into a wide range of refined products with different characteristics. The classification of these products is based on their boiling points, molecular structures, and intended applications. The primary categories of petroleum refined products include gasoline, diesel fuel, jet fuel, heating oil, liquefied petroleum gas (LPG), and residual fuel oil.

Gasoline, also known as petrol, is a light and volatile fuel primarily used in internal combustion engines for automobiles. Diesel fuel, on the other hand, is heavier and less volatile, making it suitable for diesel engines in vehicles like trucks, buses, and trains. Jet fuel, specifically designed for aviation, has a high energy density and low freezing point to meet the requirements of aircraft engines.

Heating oil, also called fuel oil, is used for space heating and fueling furnaces or boilers in residential, commercial, and industrial settings. Liquefied petroleum gas (LPG) comprises propane and butane, commonly used as a portable fuel for cooking, heating, and powering appliances like grills and camping stoves. Residual fuel oil, which has higher viscosity and sulfur content, is primarily utilized in large industrial boilers, power plants, and ships.Apart from these main categories, petroleum refining also produces various byproducts such as asphalt, lubricants, waxes, and petrochemical feedstocks. Asphalt is used for road construction, while lubricants and greases are essential for reducing friction and wear in machinery and engines. Petrochemical feedstocks serve as raw materials for producing plastics, synthetic fibers, rubber, and other chemical products.

In summary, petroleum refined products encompass a broad range of fuels and materials that play crucial roles in our daily lives. They power transportation, heat our homes and businesses, facilitate air travel, and serve as feedstocks for manufacturing essential goods. The diversity of petroleum refined products highlights the importance of refining processes in meeting our energy and material needs.

Learn more about Petroleum here:

https://brainly.com/question/12977992

#SPJ11

The required volume of the reactor is V is 0.1 lit.

The conversion of A is 50%.

The irreversible gas phase elementary reaction is given by, A + B → C + D + E. From the stoichiometry, the number of moles of A is getting consumed.

a) The irreversible gas phase elementary reaction is given by, A + B → C + D + E. From the stoichiometry, the number of moles of A is getting consumed. Hence, -

d Na/dt = k * Na * Nb

Here, k = 0.04 lit/mol.

min at 273K and E = 8000 cal/mol.R = 1.987 cal/mol K (universal gas constant) Initial concentration of A = Ca0 = 2 mol/lit

The volume of each stream is 4 lit/min and hence the volumetric flow rate is 8 lit/min.

Since the entering temperature is 300K, the reaction is taking place at 273 + 27 = 300 K.

The concentration of A and B in the mixed stream (before the reaction) is, Cao = Cbo = 2/8 = 0.25 mol/lit

The rate equation can be written as, -dCao/dt = k * Cao * Cbo

Volumetric flow rate = V * 8 lit/min = V * 8 * 60 lit/hr = 480 V lit/hr

Moles of A in the reactor at time t = na moles

Let the conversion of A be x (in fraction), then Na at time t is, Na = Na0 (1 - x)

At 80% conversion of A, x = 0.8 and Na = 0.2Na0

Also, Nb = Nao - Na = Na0 - Na = Na0 (1 - 0.2) = 0.8 Na0

The rate equation can be written as,-dNa/dt = k * Na * Nb

Substituting the values,-dNa/dt = k * Na * 0.8 Na0= k * Na^2 * 0.8

The rate equation can be integrated between the limits of Na0 and 0.2Na0, and t = 0 to t time,dt/(-Na^2 * 0.8) = k dt

Integrating between the limits of 0 to t and Na0 to 0.2Na0, (0.8 * 0.04 * t) / 1.987 = ln (Na/Na0)

At x = 0.8, Na/Na0 = 0.2

Hence, (0.8 * 0.04 * t) / 1.987 = ln 0.2

Hence, the required volume of the reactor is V = Na0 / Cao = 0.2 / 2 = 0.1 lit

b) The liquid phase reaction is given by, 2A → C From the stoichiometry, the number of moles of A is getting consumed. The rate equation can be written as,

-dCa/dt = k * Ca^2

Initial conversion of A = Xa1 = 70% = 0.7

In a plug-flow reactor, the rate equation can be integrated between the limits of Xa1 and Xa2, and t = 0 to t time,

dXa / (k * Ca^2) = dV

The volume of the reactor is not changing with time.

Substituting the values and integrating between the limits of Xa1 and Xa2, and 0 to V2,1 / k = (1 / Xa1) - (1 / Xa2)

Hence, V2,1 = (Xa2 - Xa1) / (k * Xa1 * Xa2)

Let the initial molar flow rate of A be Fao Initial molar flow rate of B = Fbo = Fao

Initial molar flow rate of inert B = Fio = Fao - Fao / 2 = Fao / 2

Initial total molar flow rate = Ft1 = Fao + Fbo + Fio = 2Fao + Fao / 2 = 5Fao / 2At 70% conversion of A, Fao / 2 is the molar flow rate of A.

Let the conversion of A be Xa2.

Then, Fa2 = Fao / 2, and Fb2 = Fbo

The molar flow rate of the inert is

, Fi2 = Ft1 - Fa2 - Fb2 = 5Fao / 2 - Fao / 2 - Fbo = 2Fao

The total molar flow rate of the mixture is,

Ft2 = Fa2 + Fb2 + Fi2 = Fao / 2 + Fbo + 2Fao = 5Fao / 2 + Fbo

The conversion of A is given by,

Xa2 = Fa1 - Fa2 / Fao

Substituting the values, Xa2 = 0.7 - (0.5 * Fao) / Fao = 0.2

When the molar flow rate of A is reduced to 40% of the original value, Fao2 = 0.4 Fao

Now, the total molar flow rate is,

Ft3 = Fa3 + Fb3 + Fi3 = Fao2 / 2 + Fbo + 2Fao = 5Fao / 2 + Fbo

At this flow rate of A, the conversion of A is,

Xa3 = Fa1 - Fa3 / Fao2

Substituting the values,

Xa3 = 0.7 - 0.5 * 0.4 = 0.5

Hence, the conversion of A is 50%.

To know more about stoichiometry refer to:

https://brainly.com/question/28780091

#SPJ11

The speed of the motor is 1760.4 rpm, the stator current is 33.59 A, the power factor is 0.872, Pconv is 21550 W, Pout is 18650 W, Tind and Tload are 107.6 Nm and the efficiency is 82.7%.

A 460V, 25hp, 60Hz, 4 pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1 = 0.641 Ω R2 0.332 Ω X1 = 1.106 Ω X2 = 0.464 Ω Xm = 26.3 Ω The total rotational losses are 1100W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2% at the rated voltage and rated frequency, find the motor's

a) speedThe synchronous speed of an induction motor is given by Ns = 120 f / P where f is the frequency of supply and P is the number of poles in the motor. Substituting these values we get, synchronous speed of the motor = 120*60 / 4 = 1800 rpmRPM of the motor = (1-s)*NsRPM of the motor = (1-0.022)*1800 = 1760.4 rpm (approx)Therefore, the speed of the motor is 1760.4 rpm.b) stator currentThe rotor impedance referred to stator side is as follows:R2/s = 0.332/0.022 = 15.09 ΩX2/s = 0.464/0.022 = 21.09 ΩThe phasor diagram for the motor is shown below:cos Φ = Pconv / PinLet, Ist be the stator current.Pconv = 3 * V * Ist * cos ΦAnd, Pconv = Pin - Rotational losses

Pconv = Pin - 1100And, Pin = V * Ist * cos Φ + V * Ist * sin Φ + V * Ist * j * (X1 + X2)And, Pin = 460 * Ist * cos Φ + 460 * Ist * sin Φ + 460 * Ist * j * (1.106 + 21.09)At 2.2% rotor slip,I2R2 = (s / (1-s))*I1R2/s = (2.2 / 97.8)*15.09 = 0.336 ΩI2X2 = (s / (1-s))*I1X2/s = (2.2 / 97.8)*21.09 = 0.470 ΩTherefore, Ist = √((V / (R1 + R2))² + ((V / (X1 + X2 + Xm))²))Ist = √((460 / (0.641 + 15.09))² + ((460 / (1.106 + 21.09 + 26.3))²)) = 33.59 A

Therefore, the stator current is 33.59 A.c) power factorThe phasor diagram shown earlier is used to calculate power factor.cos Φ = Pconv / Pincos Φ = (25 * 746) / (460 * 33.59 * cos Φ + 460 * 33.59 * sin Φ + 460 * 33.59 * j * (1.106 + 21.09))Power factor = cos Φ = 0.872d) Pconv and PoutPower developed by the motor, Pout = 25*746 = 18650 WFrom above, Pconv = Pin - 1100Pconv = 22550 - 1100 = 21550 W

Therefore, Pconv = 21550 W, Pout = 18650 We) τǐnd and τ1oadThe torque developed by an induction motor is given by the following relation:T = (Pout / ω) * (1 / s)T = (Pout / 2π * N * (1 / s)) * (1 / s)T = (18650 / (2 * π * 1760.4 * (1/0.022))) * (1/0.022)T = 107.6 NmTherefore, Tind = Tload = 107.6 Nmf) efficiencyThe efficiency of the motor is given by the relation:η = Pout / Pinη = 18650 / 22550 = 0.827 or 82.7%Therefore, the efficiency of the motor is 82.7%.Answer: Thus, the speed of the motor is 1760.4 rpm, the stator current is 33.59 A, the power factor is 0.872, Pconv is 21550 W, Pout is 18650 W, Tind and Tload are 107.6 Nm and the efficiency is 82.7%.

Learn more about torque :

https://brainly.com/question/30338175

#SPJ11