Answers
A sketch of the graph of each function is shown below.
If h > 1, the graph is translated to the right.
If h < 1, the graph is translated to the left.
What is a translation?In Mathematics and Geometry, the translation of a graph to the right simply means a digit would be added to the numerical value on the x-coordinate of the pre-image:
g(x) = f(x - N)
Where:
N is always greater than 1.
Conversely, the translation of a graph to the left simply means a digit would be subtracted from the numerical value on the x-coordinate of the pre-image:
g(x) = f(x + N)
Where:
N is always less than 1.
In conclusion, the graph of y = (x + h)² is translated to the right when h is greater than 1 while the graph of y = (x + h)² is translated to the left when h is less than 1.
Read more on function and translation here: brainly.com/question/31559256
#SPJ1
Related Questions
describe the end behavior of the graph of the function:
f(x)=11-18x^(2)-5x^(5)-12x^(4)-2x
Answers
The end behavior of the graph of the function f(x) =[tex]11 - 18x^2 - 5x^5 - 12x^4 - 2x[/tex] is that the graph decreases without bound as x approaches positive or negative infinity.
To determine the end behavior of the graph of the function f(x) = 11 - [tex]18x^2 - 5x^5 - 12x^4 - 2x,[/tex] we need to analyze the leading term of the polynomial.
The leading term is the term with the highest degree, which in this case is [tex]-5x^5[/tex]. As x approaches positive or negative infinity, the leading term dominates the behavior of the function.
The degree of the leading term is odd (5), and the coefficient is negative (-5). This tells us that as x approaches positive or negative infinity, the graph will show a similar behavior in both directions: it will either increase without bound or decrease without bound.
Since the coefficient is negative, the graph will have a downward trend as x approaches infinity in both the positive and negative directions.
In terms of the specific shape of the graph, we know that the function is a polynomial of odd degree, so it may exhibit "wavy" behavior with multiple local extrema and varying concavity.
However, when considering the end behavior, we focus on the overall trend as x approaches infinity. In this case, the function will approach negative infinity as x approaches positive infinity, and it will also approach negative infinity as x approaches negative infinity.
For more such questions on function visit:
https://brainly.com/question/11624077
#SPJ8
Water is flowing in a pipeline 600 cm above datum level has a velocity of 10 m/s and is at a gauge pressure of 30 KN/m2. If the mass density of water is 1000 kg/m3, what is the total energy per unit weight of the water at this point? Assume acceleration due to Gravity to be 9.81 m/s2.
Answers
The total energy per unit weight of the water at the specified point is determined by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. According to the principle of conservation of energy, the total energy per unit weight of the fluid in a flow system is constant and is known as Bernoulli's equation.
The following formula can be used to determine the total energy per unit weight of the water at the specified point: T.E./w = P/w + V^2/2g + Z. Where, T.E./w = Total energy per unit weightP/w = Pressure energy per unit weightV = Velocity of the water, g = Acceleration due to gravity Z = Potential energy per unit weight of the water in the pipeline. Thus, putting all the given values into the equation, we get:T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m. Therefore, the total energy per unit weight of water at the given point is 35.692 m. Water flows through pipelines due to the pressure difference between two points, and the velocity of the fluid inside the pipeline is determined by the pressure and other factors, such as the diameter of the pipe, the roughness of the surface of the pipe, and the viscosity of the fluid. Bernoulli's equation is a fundamental principle of fluid mechanics that explains how the energy of a fluid changes as it flows along a pipeline or around a curve. It is the basic principle used to describe the behavior of fluids in motion. Bernoulli's equation can be used to calculate the total energy per unit weight of a fluid at a given point in the pipeline by adding the kinetic energy per unit weight and the potential energy per unit weight of the fluid. In this problem, water is flowing through a pipeline 600 cm above datum level, with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, and the mass density of water is 1000 kg/m3. We have to calculate the total energy per unit weight of water at this point. Using Bernoulli's equation, we can obtain the following expression: T.E./w = P/w + V^2/2g + Z, Where, T.E./w = Total energy per unit weight P/w = Pressure energy per unit weight, V = Velocity of the water, g = Acceleration due to gravity, Z = Potential energy per unit weight of the water in the pipe line. Putting the given values into the equation, we get: T.E./w = 30 × 103/1000 + (10)2/(2 × 9.81) + 600/1000= 30 + 5.092 + 0.6= 35.692 m, Thus, the total energy per unit weight of water at the given point is 35.692 m.
In conclusion, the total energy per unit weight of water at a point 600 cm above datum level in a pipeline with a velocity of 10 m/s and a gauge pressure of 30 KN/m2, with a mass density of 1000 kg/m3, is 35.692 m.
Learn more about Bernoulli's equation visit:
brainly.com/question/29865910
#SPJ11
In the Lewis structure of the iodite ion,
IO2-, that satisfies the
octet rule, the formal charge on the central iodine atom is:
Answers
The formal charge on the central iodine atom in the Lewis structure of the iodite ion (IO₂⁻) that satisfies the octet rule is 0.
Formal charge can be defined as the electric charge on an atom if the electrons were distributed equally between the atoms in a compound. It can be calculated using the following formula:
FC = Valence electrons - Lone pair electrons - 1/2 Bonding electrons
In the Lewis structure of IO₂⁻, there are two oxygen atoms that each contain six valence electrons, and the central iodine atom has seven valence electrons. There are two single bonds between each oxygen atom and the central iodine atom, which account for four bonding electrons.
In the Lewis structure, there are also two lone pairs of electrons around each oxygen atom. Thus, by using the above formula, we can calculate the formal charge of the central iodine atom.
FC = 7 valence electrons - 0 lone pair electrons - 1/2 (4 bonding electrons)
FC = 7 - 0 - 2 = 5.
Thus, the formal charge on the central iodine atom is 0 since it owns the same number of valence electrons that it has in an isolated atom.
Learn more about formal charge here:
https://brainly.com/question/30459289
#SPJ11
You are required to determine the relationship between Gibbs-Duhem equation and the activity coefficient of a selected binary chemical mixture (chemical A and chemical B ) in chemical industrial process. The following model is represented the excess Gibbs energy for the selected binary chemical mixture (chemical A and chemical B ). RT
G E
=X 1
lnγ 1
+X 2
lnγ 2
The Gibbs-Duhem equation says that, in a mixture, the activity coefficients of the individual components are not independent of one another but are related by a differential equation. In a binary mixture the Gibbs-Duhem relation is; x 1
( ∂x 1
∂lnγ i
) T,P
=x 2
( ∂x 2
∂lnγ 2
) T,P
Answers
The Gibbs-Duhem equation relates the activity coefficients of the individual components in a mixture. It states that the activity coefficients are not independent of each other but are related by a differential equation.
In the case of a binary mixture (chemical A and chemical B), the Gibbs-Duhem relation can be written as:
x1 * (∂x1/∂lnγ1)T,P = x2 * (∂x2/∂lnγ2)T,P
Here, x1 and x2 represent the mole fractions of chemical A and chemical B, respectively. The activity coefficients for chemical A and chemical B are denoted as γ1 and γ2, respectively.
The equation shows that the change in mole fraction of one component (x1) with respect to the change in the logarithm of its activity coefficient (lnγ1) is proportional to the change in mole fraction of the other component (x2) with respect to the change in the logarithm of its activity coefficient (lnγ2).
This relationship helps us understand how changes in the activity coefficients of the components affect each other in a binary mixture. By studying this relationship, we can gain insights into the behavior of the mixture and make predictions about its properties.
For example, let's consider a mixture of ethanol (chemical A) and water (chemical B). If the activity coefficient of ethanol (γ1) decreases, the Gibbs-Duhem equation tells us that the mole fraction of ethanol (x1) will also decrease. Similarly, if the activity coefficient of water (γ2) increases, the mole fraction of water (x2) will increase.
Know more about Gibbs-Duhem equation:
https://brainly.com/question/33619595
#SPJ11
(a) Show that y= Ae²+ Be, where A and B are constants, is the general solution of the differential equation y"+y'-6y=0. Hence, find the solution when y(1)=2e²-e and y(0) = 1.
Answers
Consider the differential equation y'' + y' - 6y = 0. Let us assume the solution as y = e^(mx), where m is a constant. Differentiating the equation with respect to x, we get: [tex]y' = me^(mx),[/tex] [tex]y'' = m²e^(mx).[/tex]
Substituting these values into equation (1),
we get: [tex]m²e^(mx) + me^(mx) - 6e^(mx) = 0[/tex]
Simplifying further, we have:
[tex](m² + m - 6)e^(mx) = 0[/tex]
This equation can be factored as:
[tex](m + 3)(m - 2)e^(mx) = 0[/tex]
Setting each factor equal to zero, we find two possible values for m:
[tex]m = -3 and m = 2.[/tex]
The general solution of the differential equation [tex]y'' + y' - 6y = 0 is:y = Ae^(2x) + Be^(-3x) ...(2)[/tex]
where A and B are constants.
To find the solution when [tex]y(1) = 2e² - e and y(0) = 1[/tex], we substitute x = 1 into equation (2) and equate it to 2e² - e. We also substitute x = 0 into equation (2) and equate it to 1.
Solving these equations, we can determine the values of A and B.
Finally, substituting the values of A and B back into equation (2), we obtain the required solution:[tex]y = (7e^(2x) + 2e^(-3x))/5[/tex].
To know more about differential equation visit:
https://brainly.com/question/29657983
#SPJ11
A proposed mechanism for the decomposition of N₂O is given below: Which species is the catalyst? NO + N₂O-> N₂ + NO₂ 10₂ NO₂ -> NO + O NO ON₂ O NO₂ ON₂0 Page 7 of 35 Activate Windows 841 PM.
Answers
A proposed mechanism for the decomposition of N₂O is given below: NO + N₂O -> N₂ + NO₂10₂ NO₂ -> NO + O NO ON₂ O NO₂ ON₂0
The species that acts as a catalyst in the proposed mechanism for the decomposition of N₂O is NO. NO is the catalyst in this reaction.
The proposed mechanism for the decomposition of N₂O can be explained as follows:
Step 1: N₂O is oxidized by NO to form N₂ and
NO₂.NO + N₂O → N₂ + NO₂
Step 2: The NO₂ produced in step 1 is broken down to NO and O.10₂
NO₂ → NO + O NO
Step 3: The O produced in step 2 reacts with N₂ to form NO and N₂O. ON₂ O + NO → NO₂ + N₂O
Step 4: In step 3, N₂O is recycled and goes back to step 1.
NO is the catalyst in this reaction because it is consumed in step 2 but produced again in step 3, allowing the reaction to continue.
For more information on catalyst visit:
brainly.com/question/24430084
#SPJ11
In the proposed mechanism for the decomposition of N₂O, NO acts as the catalyst by facilitating the reaction between N₂O and N₂, and it is regenerated in the process.
The proposed mechanism for the decomposition of N₂O is given as follows:
1. NO + N₂O -> N₂ + NO₂
2. 10₂ NO₂ -> NO + O
3. NO + N₂O -> N₂ + NO₂
In this mechanism, the species that acts as the catalyst is NO. A catalyst is a substance that speeds up a chemical reaction without being consumed in the process. It lowers the activation energy required for the reaction to occur, allowing the reaction to proceed at a faster rate.
In the given mechanism, NO appears in the first and third steps. It reacts with N₂O to form N₂ and NO₂, and then it is regenerated in the third step by reacting with N₂O again. This shows that NO is not consumed in the overall reaction and plays a role in facilitating the reaction between N₂O and N₂.
Learn more about decomposition
https://brainly.com/question/14843689
#SPJ11
The Ash and Moisture Free analysis of coal used as fuel in a power plant is as follows:
Sulfur = 3.24% Hydrogen = 6.21% Oxygen = 4.87%
Carbon = 83.51% Nitrogen = 2.17%
Calculate the Volume Flow Rate of the Wet Gas in m3/s considering a 15.4% excess air, the mass of coal is 8788 kg/hr, the Rwg = 0.2792 kJ/kg-K, the ambient pressure is 100 kPa, and the temperature of the Wet Gas is 303 0C.
Note: Use four (4) decimal places in your solution and answer.
Answers
The data given in the question are: Mass of coal (m) = 8788 kg/hr Ambient pressure (P1) = 100 kPa Moisture present in the coal = 0% Excess air supplied = 15.4% Oxygen (O) in flue gas = 4.87% Carbon dioxide (CO2) in flue gas = 15.25% Nitrogen (N2) in flue gas = 79.58%
The volume flow rate of the wet gas is given as, Q = V x ? Where, V = Volume of the wet gas, and ? = Density of the wet gas. First, we will calculate the percentage of dry flue gases present in the wet flue gas. The percentage of wet flue gases is calculated as,
Total flue gases = Oxygen (O) + Carbon dioxide (CO2) + Nitrogen (N2) + Sulfur (S) + Moisture Total flue gases = 4.87 + 15.25 + 79.58 + 3.24 + 0 = 103.94%
Dry flue gases = Total flue gases - Moisture Dry flue gases = 103.94 - 0 = 103.94%The percentage of excess air supplied is given as 15.4%. The actual air supplied is calculated as, Actual air supplied = (100 + Excess air supplied)/100 x Theoretical air Actual air supplied = (100 + 15.4)/100 x 6.21/2.67Actual air supplied = 3.4654 kg/kg of coal Theoretical air = 6.21/2.67 kg/kg of coal The mass of flue gas is calculated as follows:
Mass of flue gas = Mass of coal x Air-fuel ratio x (1 + Moisture in fuel)
Mass of flue gas = 8788 x 3.4654 x (1 + 0)
Mass of flue gas = 106780.57 kg/hr
The volume flow rate of the wet gas is calculated as follows: Q = V x ?V = Q / ?Where the density of the wet gas is given by,
? = 0.3568 [(P1 x Mw) / (Rwg x (Tg + 273.15))]
The molecular weight of flue gas (Mw) = 28.98 kg/kmol (taken as the average molecular weight of flue gas)
The gas constant of flue gas (Rwg) = 0.2792 kJ/kg-K
The temperature of flue gas (Tg) = 303 + 273.15 = 576.15 K
The density of the wet gas,
? = 0.3568 [(100 x 28.98) / (0.2792 x 576.15)]? = 2.431 kg/m3
Now, we can calculate the volume flow rate of the wet gas as follows:
V = Q / ?106780.57 / (2.431)
= 43967.53 m3/hrQ
= 12.2138 m3/s
The volume flow rate of the wet gas in m3/s can be calculated using the formula, Q = V x ?, where V is the volume of the wet gas and ? is the density of the wet gas. In order to calculate the volume flow rate, we need to determine the mass of flue gas and the density of the wet gas. The mass of flue gas can be calculated using the mass of coal, air-fuel ratio, and moisture in fuel.
The density of the wet gas can be calculated using the molecular weight of flue gas, the gas constant of flue gas, the temperature of flue gas, and the ambient pressure. Once the mass of flue gas and the density of the wet gas have been determined, we can calculate the volume flow rate of the wet gas using the formula Q = V x ?.
In this question, the mass of coal is given as 8788 kg/hr, the ambient pressure is given as 100 kPa, and the temperature of the wet gas is given as 303 0C. The excess air supplied is given as 15.4%, and the Rwg is given as 0.2792 kJ/kg-K.
The moisture present in the coal is given as 0%. Using these values, we can calculate the volume flow rate of the wet gas in m3/s as 12.2138 m3/s. Therefore, the answer is 12.2138 m3/s.
Thus, we can conclude that the volume flow rate of the wet gas in m3/s is 12.2138 m3/s.
To learn more about Ambient pressure visit:
brainly.com/question/33544108
#SPJ11
A large block of aluminium is loaded to a stress of 405 MPa. If the fracture toughness KIc is 39 MPa√m, determine
(i) the critical length of a crack at 35° angle and
(ii) the critical radius of a buried penny-shaped crack
Answers
i). The critical length of a crack at 35° angle is approximately equal to 312m.
ii). The critical radius of a buried penny-shaped crack is approximately equal to 3.3m.
Given data:
Stress (σ) = 405 MPa
Fracture toughness (KIC) = 39 MPa √m
Crack angle (θ) = 35°
(i) The critical length of a crack at 35° angle
From the formula,
we know that the critical crack length is given by:
KIc = σ √(πa) × f (θ) …… (1)
where f (θ) is a geometry factor,
which is a function of the crack angle (θ).
Assuming f (θ) = 1.12 (for 35° angle)
KIc = 39 MPa √mσ
= 405 MPa
Putting these values in equation (1),
39 × 10⁶
= 405 × √(πa) × 1.1239 × 10⁶/(405 × 1.12) = √(πa)
31284.82 = √(πa)
πa = (31284.82)²
πa = 980,870,794.19
a = 311.99 m≈ 312m
Therefore, the critical length of a crack at 35° angle is approximately equal to 312m.
(ii) The critical radius of a buried penny-shaped crack
From the formula, we know that the critical radius is given by:
KIc = (2σ)²/(πa)
KIc = 39 MPa √mσ
= 405 MPa
Putting these values in the above equation,
39 × 10⁶ = (2 × 405)²/πa39 × 10⁶
= (2 × 405)²/πr²
(πr²) = (2 × 405)²/39 × 10⁶
πr² = 33.264
r² = 33.264/π
r² = 10.59
r = √10.59
r = 3.26 m≈ 3.3m
Therefore, the critical radius of a buried penny-shaped crack is approximately equal to 3.3m.
To know more about critical radius, visit:
https://brainly.com/question/33176751
#SPJ11
Solve the problem. 4) If the price charged for a bolt is p cents, then x thousand bolts will be sold in a certain hardware How many bolts must be sold to maximize revenue? (8 points) store, where p = 38 - A) 456 thousand bolts C) 228 bolts B) 228 thousand bolts D) 456 bolts
Answers
The number of bolts that must be sold to maximize revenue is: C) 228 bolts.
How to calculate the number of bolts that must be sold to maximize revenue?From the information provided, the amount of revenue with respect to price that's being generated in this scenario can be calculated by using the following function (equation):
R(x) = x × P(x)
Where:
x represents the number of units sold.p(x) represents the unit price.Since it is a revenue function, we would simply substitute the value of the unit price and then take the first derivative with respect to x as follows:
Revenue, R(x) = x × P(x)
Revenue, R(x) = (38 - x/12) × x
Revenue, R(x) = 38x - x²/12
Marginal revenue, R'(x) = 38 - x/6
0 = 38 - x/6
x/6 = 38
x = 6 × 38
x = 228 bolts.
Read more on revenue here: brainly.com/question/13800671
#SPJ1
Missing information:
The question is incomplete and the complete question is shown in the attached picture.
It is necessary to determine the area of a basin (in m?) On a map with a scale of 1:10,000. The average reading in the Planimeter is 6.43 revolutions for the basin. To calibrate the planimeter, a rectangle is drawn with Dimensions of 5 cm×5 cm, it is traced with the planimeter and the reading in it is 0.568 revolutions.
Answers
we can use the average reading of 6.43 revolutions for the basin to calculate its area.
Area of basin = (Planimeter reading x K) / Map scal
Area of basin = (6.43 revolutions x 44.01 cm²/rev) / 10,000 cm²/m²
Area of basin = 0.0282 m²
Yes, it is necessary to determine the area of a basin on a map with a scale of 1:10,000. The scale 1:10,000 implies that one unit of measurement on the map is equal to 10,000 units of measurement in the real world.
Therefore, the area of the basin is 0.0282 square meters.
In order to determine the area of the basin in square meters, we need to use the reading from the planimeter.
First, we need to calibrate the planimeter. To do this, a rectangle with dimensions of 5 cm x 5 cm is drawn and traced with the planimeter. The reading in it is 0.568 revolutions. We can use this reading to determine the planimeter constant (K) as follows:
K = Area of calibration rectangle / Planimeter reading
[tex]K = (5 cm x 5 cm) / 0.568[/tex] revolutions
[tex]K = 44.01 cm²/rev[/tex]
Now
To know more about determine visit:
https://brainly.com/question/29898039
#SPJ11
Do you see a scenario where the FDA merges with other authority bodies such as the USDA and in turn have better oversight and control over issues within the dietary supplement industry?
Answers
In the realm of regulatory possibilities, it is conceivable that the FDA could potentially collaborate or merge with other authority bodies such as the USDA to enhance oversight and control over issues within the dietary supplement industry.
Such a scenario could lead to improved coordination and enforcement efforts. However, the feasibility and desirability of such a merger would depend on various factors, including legal considerations, administrative challenges, and policy objectives. It is important to note that any potential changes in the organizational structure and authority of regulatory bodies would require careful evaluation and consideration of their potential impact on public health and safety.
To know more about dietary supplement industry,
https://brainly.com/question/29800602
#SPJ11
Consider the following matrix:
G=[369 12:48 12 16; 369 12]
What Octave command will you use obtain the following matrix: [4,8;3,6]
Answers
We can use the Octave command G_new = G(1:2, 2:3). This command selects rows 1 to 2 and columns 2 to 3 from the matrix G and assigns the resulting matrix to G_new.
To obtain the matrix [4,8;3,6] from the given matrix G=[369 12:48 12 16; 369 12], you can use the following Octave command:
M = G(1:2, 4:5) / 12
G(1:2, 4:5) selects the submatrix of G consisting of the first two rows (1:2) and the fourth and fifth columns (4:5).
/ 12 performs element-wise division by 12 to obtain the desired matrix [4,8;3,6].
After executing the command, the variable M will store the matrix [4,8;3,6].
Learn more about matrix here:
https://brainly.com/question/29132693
#SPJ11
What is the % dissociation of an acid, HA 0.10 M, if
the solution has a pH = 3.50? a) 0.0032 b) 35 C) 0.32 d) 5.0 e) 2.9
Answers
The percentage dissociation of an acid HA 0.10 M, when the solution has a pH = 3.50 is 2.9%.Option (e) 2.9 is correct.
According to the Arrhenius concept, an acid is a compound that releases H+ ions in an aqueous solution. According to the Bronsted-Lowry theory, an acid is a substance that donates a proton. The equilibrium constant expression of an acid HA can be expressed as follows:
HA ⇌ H+ + A
Dissociation constant:
Ka = ([H+][A-])/[HA]pH = -log[H+]pH + pOH = 14[H+] = 10-pH
The dissociation of an acid can be calculated using the following formula:
α = ( [H+]/Ka + 1) × 100%Hence, the dissociation constant of an acid is calculated using the following formula:
Ka = [H+][A-]/[HA]
= (α2×[HA])/ (100-α)
α = ( [H+]/Ka + 1) × 100%10-pH/Ka
= ([H+][A-])/[HA]0.00406
= ([H+][A-])/[HA]
Let α be the percentage dissociation of the acid α, [H+]
= [A-], [HA]
= 0.10-α/100.
Hence,0.00406 = (α/100)2×0.10-α/100/ (1-α/100)On solving, α = 2.9%.
To know more about dissociation visit:-
https://brainly.com/question/32501023
#SPJ11
A steel that has 0.151% C is subjected to a carburizing treatment. Under operating conditions, the carbon content on the surface reaches 1.1% C. The temperature at which the process is carried out is 996 °C, where the material is FCC, (D0 = 0.23 cm2/s, Q = 32900 Cal/mol°K, R =1.987 cal/mol).
Estimate the carbon content at a depth of 57 microns from the surface, (1mm=1000 microns), after 7 hours of treatment.
Suppose that the function erf(Z) can be approximately evaluated by the following equation: erf (2) = -0.3965Z2 + 1.24952 -0.0063
Answers
The estimated carbon content at a depth of 57 microns from the surface after 7 hours of treatment is approximately 0.00436949 or 0.437% C.
To estimate the carbon content at a depth of 57 microns from the surface after 7 hours of carburizing treatment, we can use the diffusion equation.
The diffusion equation is given by:
C = Co + (Cs - Co) * [1 - erf((D * t)/(2 * sqrt(Q * t)))]
Where:
C = Carbon content at a certain depth after a given time
Co = Initial carbon content
Cs = Carbon content on the surface
D = Diffusion coefficient
t = Time
Given:
Initial carbon content (Co) = 0.151% = 0.00151
Carbon content on the surface (Cs) = 1.1% = 0.011
Diffusion coefficient (D) = D0 * exp(-Q/RT)
D0 = 0.23 cm^2/s
Q = 32900 Cal/mol*K
R = 1.987 cal/mol*K
T = 996 °C = 996 + 273 = 1269 K
We can calculate the diffusion coefficient (D):
D = D0 * exp(-Q/RT)
D = 0.23 * exp(-32900/(1.987 * 1269))
D ≈ 0.23 * exp(-25.897)
D ≈ 0.23 * 2.748e-12
D ≈ 6.317e-13 cm^2/s
Now, let's calculate the carbon content at a depth of 57 microns (0.057 mm) after 7 hours (t = 7 * 3600 seconds):
C = 0.00151 + (0.011 - 0.00151) * [1 - erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600))))]
Using the given approximation equation:
erf(2) = -0.3965Z^2 + 1.24952 - 0.0063
Substituting the values:
erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600)))) = -0.3965 * ((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600))))^2 + 1.24952 - 0.0063
Simplifying the equation:
erf((6.317e-13 * (7 * 3600))/(2 * sqrt(32900 * (7 * 3600)))) ≈ 0.699
Substituting this value back into the diffusion equation:
C ≈ 0.00151 + (0.011 - 0.00151) * [1 - 0.699]
C ≈ 0.00151 + (0.011 - 0.00151) * 0.301
C ≈ 0.00151 + 0.00949 * 0.301
C ≈ 0.00151 + 0.00285949
C ≈ 0.00436949
Therefore, the estimated carbon content at a depth of 57 microns from the surface after 7 hours of treatment is approximately 0.00436949 or 0.437% C.
Know more about estimated carbon here:
https://brainly.com/question/24233481
#SPJ11
TC2411 Tutorial - Partial differential equations
For each of the following PDEs, determine if the PDE, boundary conditions or initial conditions are linear or nonlinear, and, if linear, whether they are homogeneous or nonhomogeneous. Also, determine the order of the PDE. (a) u+u,, = 2u, u, (0,y)=0 (b) u+xu=2, u(x,0)=0, u(x,1)=0 (c) u-u₁ = f(x,t), u,(x,0)=2 (d) uu,, u(x,0)=1, u(1,1)=0 (e) u,u,+u=2u, u(0,1)+ u, (0,1)=0 (f) u+eu,ucosx, u(x,0)+ u(x,1)=0
Answers
Partial differential equations (PDE) are important in physics and engineering as well as in other fields that describe phenomena that change over time and/or space.
In this task, we will determine whether the PDEs, boundary conditions, or initial conditions are linear or nonlinear, and if linear, whether they are homogeneous or nonhomogeneous. We will also determine the order of the PDE.For each of the following PDEs, determine if the PDE, boundary conditions or initial conditions are linear or nonlinear, and, if linear, whether they are homogeneous or nonhomogeneous.
Also, determine the order of the PDE.(a) u+u,, = 2u, u, (0,y)=0Given PDE: u+u,, = 2u, u, (0,y)=0The given PDE is linear and homogeneous. The order of the PDE is 2.(b) u+xu=2, u(x,0)=0, u(x,1)=0Given PDE: u+xu=2, u(x,0)=0, u(x,1)=0The given PDE is linear and nonhomogeneous.
The order of the PDE is 1.(c) u-u₁ = f(x,t), u,(x,0)=2Given PDE: u-u₁ = f(x,t), u,(x,0)=2The given PDE is linear and nonhomogeneous. The order of the PDE is 1.(d) uu,, u(x,0)=1, u(1,1)=0Given PDE: uu,, u(x,0)=1, u(1,1)=0The given PDE is nonlinear.
The order of the PDE is 2.(e) u,u,+u=2u, u(0,1)+ u, (0,1)=0Given PDE: u,u,+u=2u, u(0,1)+ u, (0,1)=0The given PDE is nonlinear. The order of the PDE is 1.(f) u+eu,ucosx, u(x,0)+ u(x,1)=0Given PDE: u+eu,ucosx, u(x,0)+ u(x,1)=0The given PDE is nonlinear. The order of the PDE is 1.
To know more about phenomena visit:
https://brainly.com/question/31825772
#SPJ11
Ethylene is produced by the dehydrogenation of ethane. If the feed includes 0.5 mole of steam (an inert diluent) per mole of ethane at 323 K, 1 bar and if the reaction reaches and equilibrium at 1100 K and 1 bar, determine the amount of heating needed or generated by assuming the complete dehydrogenation of ethane. Use the whole expansion of heat capacity values
Answers
The amount of heating needed or generated by assuming the complete dehydrogenation of ethane is 40%
Ethylene is produced by the dehydrogenation of ethane.
If the feed includes 0.5 mole of steam (an inert diluent) per mole of ethane at 323 K, 1 bar and if the reaction reaches and equilibrium at 1100 K and 1 bar,
Consider dehydrogenation r × n of ethane.
C₂H₆ ⇒ C₂H₄ + H₂
To determine the amount of heating needed or generated by assuming the complete dehydrogenation of ethane.
From the r × n 1 mol gm ethane gives 1 mol of ethane & 1 mol fuel includes 0.5 mole of steam (an inert diluent) per mole of ethane.
Therefore, total number of moles on side = 2.5 moles.
Total = 2.5 moles
% composition of ethane
= ethane/n total * 100
= 1/2.5 * 100 = 40%
Therefore, 40% the amount of heating generated complete dehydrogenation of ethane.
Learn more about dehydrogenation of ethane here;
https://brainly.com/question/33409739
#SPJ4
Which among the following statements is true? Every differential equation has at least one solution. A single differential equation can serve as a mathematical model for many different phenomena. Every differential equation has a unique solution. None of the mentioned
Answers
Every differential equation has a unique solution.
What is the nature of solutions for a given differential equation?Differential equations describe the relationships between a function and its derivatives. The nature of solutions for a given differential equation depends on the specific equation and its initial or boundary conditions.
The statement "Every differential equation has a unique solution" is true. According to the existence and uniqueness theorem for ordinary differential equations, if a differential equation is well-posed, meaning it satisfies certain conditions, then there exists a unique solution that satisfies the equation and the given initial or boundary conditions.
While it is true that a single differential equation can serve as a mathematical model for many different phenomena, this does not imply that every differential equation has multiple solutions. Each differential equation has its own set of solutions, and the uniqueness of these solutions is determined by the initial or boundary conditions imposed.
Learn more about: solution
brainly.com/question/1616939
#SPJ11
A sorting algorithm takes two operations to sort an array with one item in it. Increasing the number of items in the array from n to n + 1 requires at least n + 2 more. Prove by induction that the number of operations required to sort an array with n items requires at least 1 2 n(n + 3) operations
Answers
Given that: A sorting algorithm takes two operations to sort an array with one item in it. Increasing the number of items in the array from n to n + 1 requires at least n + 2 more.
The proof is by induction. Base case: For n = 1, the number of operations required to sort an array with one item = 2. Using 12n(n + 3), the number of operations required = 12(1)(4) = 4. The value of 4 is greater than the required 2. The base case holds.
The number of operations required to sort an array with k+1 items require at least.
[tex]12(k+1)[(k+1) + 3] = 12(k+1)(k+4)[/tex]
Using the inductive hypothesis, the number of operations required to sort an array with k+1 items is at least:
[tex]12k(k + 3) + k + 3= 12k² + 13k + 3[/tex]
Using
[tex]12(k+1)(k+4), 12k² + 49k + 48.[/tex]
The number of operations required to sort an array with k+1 items is at least.
12(k+1)(k+4) for k ≥ 1.
The proof is complete.
To know more about number visit:
https://brainly.com/question/3589540
#SPJ11
Why is it important to never exceed an establishment's licensed maximum capacity?
a.Overcrowding can make the premises unsafe and is a violation of the LLA.
b.Overcrowding leads to lower tips.
c. Fire exits can be blocked.
d.Servers cannot safely monitor how much alcohol each guest is consuming
Answers
They are not as significant and directly related to the safety concerns associated with exceeding the licensed maximum capacity. The primary focus should be on ensuring the safety and well-being of patrons and staff within the establishment.
The correct answer is a. Overcrowding can make the premises unsafe and is a violation of the LLA (Liquor License Agreement).
It is important to never exceed an establishment's licensed maximum capacity due to several safety reasons:
Safety hazards: Overcrowding can lead to safety hazards such as difficulty in evacuating the premises during emergencies, increased risks of accidents, and limited access to emergency exits. In case of a fire or other emergencies, it is crucial to have enough space and clear pathways for people to exit the building safely.
Structural integrity: Buildings have a maximum capacity determined by their design and structural integrity. Exceeding this capacity can put excessive stress on the building's structure, which may lead to collapses or structural failures.
Compliance with regulations: Licensed establishments are required to adhere to the regulations set by local authorities, including the maximum capacity specified in their liquor license agreement. Violating the licensed maximum capacity is not only a safety concern but also a violation of legal requirements and can result in fines, penalties, or even the revocation of the establishment's license.
While options b, c, and d may have their own implications, such as lower tips, blocked fire exits, or difficulty in monitoring alcohol consumption, they are not as significant and directly related to the safety concerns associated with exceeding the licensed maximum capacity. The primary focus should be on ensuring the safety and well-being of patrons and staff within the establishment.
To know more about maximum visit
https://brainly.com/question/16696252
#SPJ11
Suppose that you made three purchases using your credit card during the month of January. - The first purchase was on January 8th for $492. - The second purchase was on January 19th for $292. - The third purchase was on January 24ti . If your average daily balance for January was $695, what was the dollar amount of your last purchase? Remember: - There are 31 days in January. - You made no purchases between January 1 st and January 7 th. - This question is not asking for the card's final January balance. Round your answer to the nearest dollar. Question 4 A $14,513 par value bond whose coupon rate is 4.9% is purchased. If the investment represents a current yield of 3.1%, compute the bond's market price at the time of the purchase. Round your answer to the nearest dollar.
Answers
Average Daily Balance:It is defined as the average balance for a day or a month in a credit account. The balance is calculated by adding the unpaid balance at the end of each day and dividing the total by the number of days in a month.
According to the question, the average daily balance for January was $695. Therefore, the total balance for January was:$695 x 31 = $21,545.Let x be the last purchase amount. So, the balance after two transactions:$21,545 – $492 – $292 = $20,761.The third transaction would have made the balance equal to x + $20,761 as there are 31 days in January. Therefore, we can represent the equation as: x + $20,761 = $695 x 31.Since x is the last purchase amount, we must isolate it to find it: x + $20,761 = $21,545.Dividing both sides by 1, we get: x = $784. The question asks us to determine the amount of the last purchase, given three transactions and the average daily balance for January 2021. We begin by calculating the average daily balance for January 2021, which is $695. This is calculated by taking the balance at the end of each day and dividing it by the number of days in January 2021, which is 31. Therefore, the total balance for January 2021 is $695 x 31 = $21,545. We are given that the first purchase was $492 and the second purchase was $292, which means that the remaining balance after the second purchase is $20,761. We are asked to find the amount of the third purchase, which means that we need to add this amount to the remaining balance to get the total balance at the end of January 2021. We can set up an equation to solve for the third purchase amount. Let x be the amount of the third purchase. Therefore, x + $20,761 = $695 x 31. Solving for x, we get x = $784. Therefore, the amount of the last purchase was $784.
Therefore, the amount of the last purchase was $784, which was obtained by adding the remaining balance of $20,761 to the third purchase.
To learn more about Average Daily Balance visit:
brainly.com/question/31013957
#SPJ11
What is the volume of this cylinder?
Use ≈ 3.14 and round your answer to the nearest hundredth.
The top of the cylinder is 14 meters
The side of the cylinder is 9 meters.
Give the answer in cubic meters and round to the nearest hundredth.
Answers
Answer:
1384.74
Step-by-step explanation:
The formula for finding volume is πr²h
π = 3.14
Diameter is 14 m. But r stands for radius.
Radius is 1/2 of diameter
Therefore; radius is 1/2 of 14 = 7
r = 7
Side of cylinder is equal to height(h)
Therefore h is 9m.
V = πr²h
V= 3.14 x7²x9
V=1384.74 meters.
A school purchased sand to fill a sandbox on its playground. The dimensions of the sandbox in meters and the total cost of the sand in dollars are known. Which units would be most appropriate to describe the cost of the sand?
Answers
The most appropriate units to describe the cost of the sandbox would indeed be dollars.
When describing the cost of an item or service, it is essential to use the unit that represents the currency being used for the transaction. In this case, the total cost of the sand for the school's sandbox is given in dollars. To maintain consistency and clarity, it is best to express the cost in the same unit it was provided.
Using dollars as the unit for the cost allows for clear communication and understanding among individuals involved in the transaction or discussion. Dollars are widely recognized as the standard unit of currency in many countries, including the United States, where the dollar sign ($) is commonly used to denote monetary values.
Using meters, the unit for measuring the dimensions of the sandbox, to describe the cost would be inappropriate and could lead to confusion or misunderstandings. Mixing units can cause ambiguity and hinder effective communication.
Therefore, it is most appropriate to describe the cost of the sand in dollars, aligning with the unit of currency provided and commonly used in financial transactions. This ensures clarity and facilitates accurate comprehension of the cost associated with the sand purchase for the school's sandbox.
for similar questions on sandbox.
https://brainly.com/question/31290675
#SPJ8
For problems 1 and 2, use the set A = {factors of 45} = {1,3,5,9,15,45} 1. [ 15 points ] Show that the relation R defined by : x Ry iff x mod 5 = y mod 5 is an equivalence relation, and list the equivalence classes. 2. [15 points ] Show that the "divides" relation is a partial ordering, and draw the Hasse diagram.
Answers
The relation R defined by "x Ry iff x mod 5 = y mod 5" is an
equivalence relation. The equivalence classes are [1], [2], [3], [4], and [0], where each equivalence class contains elements that have the same remainder when divided by 5.
The "divides" relation is a partial ordering. It satisfies the properties of reflexivity, antisymmetry, and transitivity. The Hasse diagram represents the elements and their relationships in a partially ordered set, where each element is represented as a node, and an arrow between nodes indicates that one element divides the other.
To show that the relation R is an equivalence relation, we need to prove that it satisfies the properties of reflexivity, symmetry, and transitivity.
Reflexivity: For any element x in the set A, x mod 5 = x mod 5, so x Rx. This shows that R is reflexive.
Symmetry: If x mod 5 = y mod 5, then y mod 5 = x mod 5, so x Ry implies y Rx. This shows that R is symmetric.
Transitivity: If x mod 5 = y mod 5 and y mod 5 = z mod 5, then x mod 5 = z mod 5, so x Ry and y Rz imply x Rz. This shows that R is transitive.
The equivalence classes for the relation R are formed by grouping elements that have the same remainder when divided by 5. In this case, the equivalence classes are [1], [2], [3], [4], and [0].
The "divides" relation is a partial ordering relation. It satisfies the following properties:
Reflexivity: For any element x in the set A, x divides x. This shows that the relation is reflexive.
Antisymmetry: If x divides y and y divides x, then x = y. This shows that the relation is antisymmetric.
Transitivity: If x divides y and y divides z, then x divides z. This shows that the relation is transitive.
The Hasse diagram is a graphical representation of the partial ordering relation. In the case of the "divides" relation, each element in the set A is represented as a node, and an arrow is drawn from element x to element y if x divides y.
The diagram arranges the elements in a way that shows the partial ordering relationship between them, with the minimal elements at the bottom and the maximal elements at the top.
To learn more about equivalence relation visit:
brainly.com/question/30881829
#SPJ11
The specific gravity of the liquid passing through the 1 cm diameter pipe shown in the figure is (y) = 10 K/N3 and the dynamic viscosity (mu) is 3*10^-3Pa.s.
Calculate whether the liquid will be stationary, upstream or downstream, within the framework of the conservation of energy principles.
Also find the average velocity (V) of the liquid in the pipe.
I couldn't upload the shape unfortunately, but its features are as follows
elevation=0m , p=200 KpA elevation=10m p=110 kpA
Answers
The liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s.
As we know that the flow of the liquid is driven by the difference in pressure and it always flows from higher pressure to lower pressure.
The specific gravity of the liquid passing through the 1 cm diameter pipe is given as y = 10 kN/m³ and the dynamic viscosity is given as μ = 3 × 10⁻³ Pa·s.
Calculation:The pressure difference between the two points is given byΔp = 200 - 110 = 90 kPaNow, the Reynolds number can be calculated by using the formula below:Re = (ρVD)/μWhere;V is the velocity of the fluid,D is the diameter of the pipeρ is the density of the fluid.
The formula for Bernoulli's principle for incompressible fluids is given by:P1 + 1/2 ρV1^2 + ρgy1 = P2 + 1/2 ρV2^2 + ρgy2Let us consider the two points, one at the top and another at the bottom of the tube.
Let point 1 be at the top, and point 2 be at the bottomPoint 1: P1 = 200 kPa, V1 = 0, y1 = 0Point 2: P2 = 110 kPa, y2 = 10 m, V2 = ?.
Substitute the given values into Bernoulli's equation, we get:
P1 + 1/2ρV₁² + ρgy1 = P2 + 1/2ρV₂² + ρgy2.
By substituting the values given in the problem, we get:
200 × 103 + 1/2 × 10 × V₁² + 0 = 110 × 103 + 1/2 × 10 × V₂² + 10 × 10 × 10 × 10.
As V1 is equal to zero, we can solve the above equation for V2 and we get:
V2 = 11.54 m/sBy using the formula of Re, we get;Re = (ρVD)/μ,
Where;
V = 11.54 m/s,
D = 0.01 mμ,
0.01 mμ = 3 × 10⁻³ Pa.s,
ρ = 10 kN/m3
10 kN/m3 = 10000 kg/m3,
Re = (10000 × 11.54 × 0.01)/ (3 × 10^-3),
Re = 3.85 × 10⁵.
As the Reynolds number is greater than 4000, the flow is turbulent.As the Reynolds number is greater than 4000, the flow is turbulent.
Hence, the liquid will be flowing downstream in the pipe.As per the conclusion we can say that the liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s.
From the above analysis, we can conclude that the liquid will be flowing downstream in the pipe and the average velocity of the liquid in the pipe is 11.54 m/s. This can be explained using Bernoulli's principle and Reynolds number.
To know more about Bernoulli's principle visit:
brainly.com/question/13098748
#SPJ11
[5 marks] Determine the splitting field E of the polynomail x^3+2 over Q. (a) Write down the Galois group Gal(E/Q). (b) Write down all the subgroups of Gal(E/Q). (c) Down all the subfields L of E and their corresponding subgroups Gal(E/L) in Gal(E/Q).
Answers
(a) The Galois group Gal(E/Q) is isomorphic to the group of permutations of the three roots of the polynomial x^3+2.
(b) The subgroups of Gal(E/Q) are the identity subgroup, the subgroups generated by single transpositions, the subgroup generated by cyclic permutations, and the entire Galois group Gal(E/Q).
(c) The subfields L of E correspond to the fixed fields of the subgroups of Gal(E/Q), with Gal(E/E) = {identity}, Gal(E/L) corresponding to the subfield fixed by the corresponding subgroup.
To determine the splitting field E of the polynomial x^3+2 over Q, we need to find the field extension that contains all the roots of the polynomial.
To find the roots, we set the polynomial equal to zero and solve for x:
x^3 + 2 = 0
By factoring out a 2, we can rewrite the equation as:
x^3 = -2
Taking the cube root of both sides, we get:
x = -2^(1/3)
So, the roots of the polynomial are -2^(1/3), ω(-2)^(1/3), and ω^2(-2)^(1/3), where ω is a complex cube root of unity.
The splitting field E of the polynomial x^3+2 over Q is the smallest field extension of Q that contains all the roots of the polynomial. In this case, we can see that the roots of the polynomial are complex numbers, so the splitting field E is the field extension of Q that contains the complex numbers -2^(1/3), ω(-2)^(1/3), and ω^2(-2)^(1/3).
The Galois group Gal(E/Q) is the group of automorphisms of the splitting field E that fix the field Q. In this case, since E is a field extension of Q that contains complex numbers, the Galois group Gal(E/Q) is isomorphic to the group of permutations of the three roots of the polynomial x^3+2.
The subgroups of Gal(E/Q) can be obtained by considering the possible permutations of the three roots of the polynomial x^3+2. The subgroups of Gal(E/Q) are:
- The identity subgroup, which contains only the identity permutation.
- The subgroup generated by a single transposition, which switches two of the roots.
- The subgroup generated by a cyclic permutation, which cyclically permutes the three roots.
- The entire Galois group Gal(E/Q).
The subfields L of E can be obtained by considering the fixed fields of the subgroups of Gal(E/Q). The corresponding subgroups Gal(E/L) in Gal(E/Q) are:
- The fixed field of the identity subgroup is E itself, so Gal(E/E) = {identity}.
- The fixed field of the subgroup generated by a single transposition is the subfield of E that is fixed by that transposition.
- The fixed field of the subgroup generated by a cyclic permutation is the subfield of E that is fixed by that cyclic permutation.
- The fixed field of the entire Galois group Gal(E/Q) is Q itself.
To learn more about polynomial visit : https://brainly.com/question/1496352
#SPJ11
Construct a proof for the following argument.
~(∃x)(Ax • Bx)
~((x)(Bx ⊃ Cx)
(x) ((~Ax • Dx) ⊃ ~Bx)
/Δ ~(x) (Bx ⊃ Dx)
Answers
The argument to be proven is Δ: ~(x)(Bx ⊃ Dx). This can be demonstrated using a proof by contradiction, assuming the negation of Δ and deriving a contradiction.
To prove Δ: ~(x)(Bx ⊃ Dx), we will use a proof by contradiction. We assume the negation of Δ, which is ((x)(Bx ⊃ Dx)). By double negation, this can be simplified to (x)(Bx ⊃ Dx).
Next, we will introduce a new assumption, let's call it γ, which states (∃x)(Bx • ~Dx). We will aim to derive a contradiction from this assumption.
By using the existential elimination (∃E) rule, we can introduce a specific variable, say c, such that (Bc • ~Dc) holds.
Now, we can apply the universal elimination (∀E) rule to the assumption (x)(Bx ⊃ Dx) using the variable c, which gives us Bc ⊃ Dc.
Using modus ponens, we can combine Bc ⊃ Dc with Bc • ~Dc to derive a contradiction, which negates the assumption γ.
Having derived a contradiction, we can conclude that the negation of Δ: ~(x)(Bx ⊃ Dx) is true, leading to the validity of Δ itself: ~(x)(Bx ⊃ Dx).
Learn more about Contradiction proof: brainly.com/question/30459584
#SPJ11
The argument to be proven is Δ: ~(x)(Bx ⊃ Dx). This can be demonstrated using a proof by contradiction, assuming the negation of Δ and deriving a contradiction.
To prove Δ: ~(x)(Bx ⊃ Dx), we will use a proof by contradiction. We assume the negation of Δ, which is ((x)(Bx ⊃ Dx)). By double negation, this can be simplified to (x)(Bx ⊃ Dx).
Next, we will introduce a new assumption, let's call it γ, which states (∃x)(Bx • ~Dx). We will aim to derive a contradiction from this assumption.
By using the existential elimination (∃E) rule, we can introduce a specific variable, say c, such that (Bc • ~Dc) holds.
Now, we can apply the universal elimination (∀E) rule to the assumption (x)(Bx ⊃ Dx) using the variable c, which gives us Bc ⊃ Dc.
Using modus ponens, we can combine Bc ⊃ Dc with Bc • ~Dc to derive a contradiction, which negates the assumption γ.
Having derived a contradiction, we can conclude that the negation of Δ: ~(x)(Bx ⊃ Dx) is true, leading to the validity of Δ itself: ~(x)(Bx ⊃ Dx).
Learn more about Contradiction proof: brainly.com/question/30459584
#SPJ11
Your family is considering investing $10,000 in a stock and made this graph to track Its growth over time. It is estimated it will grow 7% per year. Write the function that represents the exponential growth of the investment.
Answers
The function representing the exponential growth of the investment is:
A(t) = $10,000 * (1 + 0.07)^t
To represent the exponential growth of the investment, we can use the formula for compound interest:
A = P(1 + r/n)^(nt)
Where:
A = the final amount after time t
P = the principal amount (initial investment)
r = annual interest rate (as a decimal)
n = number of times interest is compounded per year
t = time in years
In this case, the initial investment is $10,000, and the growth rate is 7% per year (0.07 as a decimal). We'll assume the interest is compounded annually, so n = 1.
The investment's exponential growth function is represented by the:
A(t) = 10000(1 + 0.07)^t
Simplifying further:
A(t) = 10000(1.07)^t
This function shows how the investment will grow over time, with the value of t representing the number of years.
for such more question on exponential growth
https://brainly.com/question/19961531
#SPJ8
3. What is the diameter change of a 50-ft spherical tank made of ½" steel plate due to internal pressure of 100 psi? Assume that the tank may be considered as "thin-walled" and that the steel remains elastic and has the properties Elastic modulus Poisson's ratio Internal pressure Thickness steel Diameter = = 11 30,000,000 psi 0.3 100 psi ½" 50 ft
Answers
The diameter change of the 50-ft spherical tank due to internal pressure of 100 psi is approximately 0.0214 inches.
To calculate the diameter change of the spherical tank, we can use the formula for the change in diameter due to internal pressure in a thin-walled sphere:
ΔD = (4 * E * ΔP * D) / (3 * (1 - ν^2) * t)
where:
ΔD is the change in diameter
E is the elastic modulus of the steel (30,000,000 psi)
ΔP is the internal pressure (100 psi)
D is the original diameter of the tank (50 ft)
ν is the Poisson's ratio of the steel (0.3)
t is the thickness of the steel plate (0.5 inches)
Plugging in the given values into the formula, we have:
ΔD = (4 * 30,000,000 * 100 * 50) / (3 * (1 - 0.3^2) * 0.5)
Simplifying the equation, we get:
ΔD = 0.0214 inches
Therefore, the diameter change of the 50-ft spherical tank due to the internal pressure of 100 psi is approximately 0.0214 inches.
Learn more about diameter
brainly.com/question/32968193
#SPJ11
Which of the following matches the answers you put for product on each of the word problems (check all that is correct) (equilibrium)
(Economics)
Automobiles
Televisions
Crude oil
Oranges
Pepsi
Answers
We can fill up the result of each of the events as follows:
If the local union in an automobile market negotiates a 20% pay raise in the market, the supply of cars might reduce because of an increase in production costs but the productivity of employees might increase and cause improved production If the president signs a bill to have the IRS send a refund in taxes to all Americans, the television market will experience a boom. If OPEC passes an agreement to restrict crude oil production, there will be a sharp spike in the gasoline market.If an unexpected winter storm damages the Florida orange crop, the market for orange juice will experience a decline and a lack of patronage.If Coca-Cola decides to drop the price of its can from 50 to 30 cents then the market will experience an increase in sales volume.How to fill up the chartTo fill up the chart, you have to carefully consider the events happening and determine whether they would impact the organization positively or negatively.
In the first instance, we are told that the automobile market increases the wages of its workers. First, this might cause an increase in their cost of production, thus reducing the revenue made. Also, the employees might experience more satisfaction and improve their productivity.
Also, if Coca-Cola drops the price of its can from 50 to 30 cents, then it might experience an increase in sales volume.
Learn more about economics here:
https://brainly.com/question/17996535
#SPJ1
A 1.44-g sample of an unknown gas has a volume of 573 mL and a pressure of 809mmHg at 44.8∘C. Calculate the molar mass of this compound. g/m0l
Answers
The molar mass of the unknown compound is 73.8 g/mol.
Given: Mass (m) = 1.44 g
Volume (V) = 573 mL
Pressure (P) = 809 mmHg
Temperature (T) = 44.8 ∘C
The Ideal Gas Law is defined as
PV = nRT where P = pressure V = volume R = gas constant T = temperature n = moles of gas.
The first step is to convert the given volume into liters because the value of R used in the ideal gas law has units of
L•atm/mol•K.1 m
L = 0.001 L573 m
L = 0.573 L
Let's convert the temperature from degrees Celsius to Kelvin by adding 273.150.15 K = 318.95 K
Now the Ideal Gas Law can be written as:
PV = nRTn = (PV)/(RT)
Substitute the given values: n = (0.809 atm x 0.573 L)/((0.0821 L•atm/mol•K) x 318.15 K)
n = 0.0195 mol
Let's use the formula of molar mass.
Molar mass = mass/moles
Substitute the given values. molar mass = 1.44 g/0.0195 mol
molar mass = 73.8 g/mol
Therefore, the molar mass of the unknown compound is 73.8 g/mol. This is the required answer.
Learn more about Ideal Gas Law
brainly.com/question/30458409
#SPJ11