To call a regressive model that you have created, you can use the following syntax: `regressive_model.predict(independent_variables)`. Here is a step-by-step explanation of how this works:
1. First, create a new column in the `dataframe_stdev` called "Prediction". This column will hold the regressive predictions.
2. Next, apply the regression equation that you created in the previous step to the independent variables in the `dataframe_stdev` dataset using the `.predict()` function. This will generate a column filled with your regressive predictions.
3. Now, you can create a Dual-Axis Plot with the following axes items:
- Axes One should contain:
- Volumetric Flow Meter 2
- Pump Efficiency
- Horse Power
- Axes Two should contain:
- Pump Failure (1 or 0)
- Prediction
Note: To create a dual-axis plot, you can use the `.twinx()` function. This function helps you plot two different y-axes on the same graph.
By following these steps, you will be able to call your regressive model, create a new column for predictions, and plot the desired data on a dual-axis plot.
Know more about regressive model:
https://brainly.com/question/31969332
#SPJ11
Using Laplace Transform to solve the following equations
y′′+3y′+2y=e^t, y(0)=0, y′(0)=1.
The solution to the differential equation [tex]y′′+3y′+2y=e^t[/tex], with initial conditions y(0)=0 and y′(0)=1, is:
[tex]y(t) = (8/5)e^t - (2/5)e^(-2t)[/tex]
To solve the differential equation [tex]y′′+3y′+2y=e^t[/tex]using Laplace Transform, we can follow these steps:
1: Take the Laplace Transform of both sides of the equation. Recall that the Laplace Transform of y(t) is denoted as Y(s), where s is the complex frequency variable.
2: Apply the initial conditions y(0)=0 and y′(0)=1 to find the constants in the transformed equation.
3: Solve the transformed equation for Y(s).
4: Take the inverse Laplace Transform of Y(s) to find the solution y(t).
Let's go through each step in detail:
1: Taking the Laplace Transform of [tex]y′′+3y′+2y=e^t,[/tex] we get:
[tex]s^2Y(s) - sy(0) - y′(0) + 3(sY(s) - y(0)) + 2Y(s) = 1/(s-1)[/tex]
Substituting y(0)=0 and y′(0)=1, we have:
[tex]s^2Y(s) + 3sY(s) + 2Y(s) - s = 1/(s-1)[/tex]
2: Simplifying the equation, we get:
[tex]Y(s)(s^2 + 3s + 2) - s = 1/(s-1)[/tex]
[tex]Y(s)(s^2 + 3s + 2) = 1/(s-1) + s[/tex]
[tex]Y(s)(s^2 + 3s + 2) = (1 + (s-1)^2) / (s-1)[/tex]
[tex]Y(s) = (1 + (s-1)^2) / ((s-1)(s+2))[/tex]
3: We can rewrite the expression for Y(s) as follows:
Y(s) = 1/(s-1) + (s+1)/(s-1)(s+2)
Using partial fraction decomposition, we can further simplify this expression:
Y(s) = 1/(s-1) + (A/(s-1)) + (B/(s+2))
Multiplying through by the common denominator (s-1)(s+2), we have:
1 = 1 + A(s+2) + B(s-1)
Comparing coefficients, we find A = 3/5 and B = -2/5.
So, Y(s) = 1/(s-1) + (3/5)/(s-1) - (2/5)/(s+2)
4: Taking the inverse Laplace Transform of Y(s), we get:
[tex]y(t) = e^t + (3/5)e^t - (2/5)e^(-2t)[/tex]
Therefore, the solution to the differential equation [tex]y′′+3y′+2y=e^t[/tex], with initial conditions y(0)=0 and y′(0)=1, is:
[tex]y(t) = (8/5)e^t - (2/5)e^(-2t)[/tex]
This is the final solution to the given differential equation.
Learn more about differential equation from this link:
https://brainly.com/question/25731911
#SPJ11
Which one of the following is the factor of mental processes? a. Personality b. Attention c. Motivation O d. Emotion
Attention is a vital aspect of mental processing since it is responsible for selecting and processing relevant information in the environment. When we concentrate on something, we are effectively filtering out distractions and concentrating on the task at hand, which enables our mental processes to function more effectively. Attention is necessary for both selective attention and divided attention, which are two critical mechanisms for cognitive functioning.
Factor of mental processes: Attention is a factor of mental processes. The cognitive processes related to memory, attention, and information processing are referred to as mental processes. Perception, reasoning, and problem-solving are all mental processes that are critical to daily life. Memory, perception, attention, and reasoning are all related, and they are used to create a holistic image of the world in which we live.
It is necessary to devote attention to the tasks at hand in order to guarantee that mental processes function effectively. Attention is defined as the process of concentrating mental efforts on a specific stimulus. It is considered a critical mechanism for the selection, processing, and integration of information. Attention is essential for several mental processes, including perception, memory, and problem-solving.
To understand the importance of attention in mental processes, we must first examine the two primary functions of attention: Selective attention. Divided attention, Selective attention is the ability to focus on one stimulus while ignoring others. It involves filtering out irrelevant information and concentrating on what is significant. Divided attention, on the other hand, is the ability to focus on several tasks at once, but only if they do not require significant cognitive processing.
Explanation: In conclusion, attention is a vital factor of mental processes. Mental processes are complex functions that include memory, perception, attention, and reasoning, among other things. They enable us to interact effectively with our environment. Attention is critical for efficient functioning of the cognitive processes involved in mental processes. In cognitive psychology, attention is recognized as a crucial mechanism for selection, processing, and integration of information, and is necessary for perception, memory, and problem-solving. Attention is a vital aspect of mental processing since it is responsible for selecting and processing relevant information in the environment. When we concentrate on something, we are effectively filtering out distractions and concentrating on the task at hand, which enables our mental processes to function more effectively. Attention is necessary for both selective attention and divided attention, which are two critical mechanisms for cognitive functioning.
To know more about functions visit
https://brainly.com/question/21426493
#SPJ11
7. When an excited electron in an atom moves from the ground state, the electron i) A. absorbs energy as it moves to a higher energy state. B. absorbs energy as it moves to a lower energy state. C. emits energy as it moves to a higher energy state. D. emits energy as it moves to a lower energy state. ii) Justify your answer
When an excited electron in an atom moves from the ground state, the electron absorbs energy as it moves to a higher energy state.
The correct option is A.
Absorbs energy as it moves to a higher energy state. How does an atom's electrons change energy levels When an electron in an atom absorbs energy it becomes excited and may shift to a higher energy level.
Excited atoms are unstable and must discharge the energy they absorb to return to their previous state. Electrons in an atom can emit energy as they move to a lower energy level. The electron is emitted in the form of light.
To know more about electron visit :
https://brainly.com/question/12001116
#SPJ11
In recent times, aluminum alloys have gained more and more space in the industry, due to their low density and the increasing increase in their mechanical strength, due to the addition of alloying elements, such as Mg, Si, and P, in their composition. . One of the most practical uses in our lives is the use of aluminum in soda cans. These alloys are largely made up of alloy 1050, which has a chemical composition of 99.5% aluminum per kilogram. Aluminum has an excellent ductility, which for this reason, and with the help of heat treatments, we manufacture aluminum sheets as thin as those we use in the kitchen of our homes.
Based on the literature, answer what is the crystal structure of aluminum?
Calculate the density (g/cm3) of aluminum, knowing that its radius is 0.1431 nm and its atomic weight is 26.981 g/mol.
Aluminum has a face-centered cubic crystal structure. The density of aluminum is 2.70 g/[tex]cm^3[/tex].
Crystal structure of aluminum
Aluminum has a face-centered cubic (fcc) crystal structure. This means that each atom is surrounded by 12 other atoms, forming a cube. The fcc crystal structure is the most common crystal structure for metals, and it is what gives aluminum its high strength and ductility.
Density of aluminum
The density of aluminum can be calculated using the following formula:
Density = Mass / Volume
The mass of an aluminum atom is 26.981 g/mol, and the volume of an aluminum atom is (4/3)π * [tex](0.1431 nm)^3[/tex].
The density of aluminum is then:
Density = 26.981 g/mol / (4/3)π * [tex](0.1431 nm)^3[/tex] = 2.70 g/[tex]cm^3[/tex]
To learn more about density here:
https://brainly.com/question/29775886
#SPJ4
A gas turbine is used to generate electricity. It can be modelled as a cycle utilising air as the working fluid. The air is initially compressed in a two stage compressor from 1 bar to 16 bar. The air is initially at 32"C. Between the two stages of the compressor, there is an intercooler which reduces the temperature to 32°C. It may be assumed that the two stages of the compressor have an equal pressure ratio. The compressed gas then passes to a heat exchanger, which models the combustion chamber, where it is heated to 1500'C. The hot gases are then expanded through a turbine to extract work, and the exhaust gases vented at 1 bar. It may be assumed throughout that all rotating machinery has an isentropic efficiency of 90% What are the advantages and disadvantages of using a multi-stage compressor over a single stage? [2] ) How are the isentropic efficiencies of a compressor and a turbine defined? [2] (i) For an isentropic process on a perfect gas, it can be shown that pr constant. Starting from this expression, show that: T: T: [4] () For this cycle, calculate the back work ratio and the thermal efficiency. How does this compare with the maximum efficiency possible for this cycle? How could you improve the thermal efficiency of this process? [12] Data: For air: Cp 1.15 kJ/kg Ky 1.33 P.
The advantages of using a multi-stage compressor over a single stage include higher overall pressure ratios, improved efficiency, and better performance. The division of compression into multiple stages allows for lower pressure ratios per stage, reducing the workload and enabling better control. Intercooling between stages further enhances efficiency. However, multi-stage compressors are more complex, expensive, and have a higher risk of operational issues.The main disadvantages of using a multi-stage compressor are increased complexity, higher costs, and a greater potential for operational issues compared to single-stage compressors.
Advantages and disadvantages of using a multi-stage compressor over a single stage:
The main advantage of a multi-stage compressor is its ability to achieve higher overall pressure ratios, leading to improved efficiency and performance. By dividing the compression process into multiple stages, each stage operates at a lower pressure ratio, reducing the workload on each stage and allowing for better control and optimization. Additionally, intercooling between stages can help lower the temperature and improve efficiency further. However, multi-stage compressors are more complex and expensive than single-stage compressors, requiring additional equipment, maintenance, and space. They also introduce more potential points of failure, increasing the risk of operational issues.
Isentropic efficiencies of a compressor and a turbine are defined as follows:
The isentropic efficiency of a compressor is the ratio of the actual work input to the ideal work input, assuming an isentropic (reversible adiabatic) process. It represents the efficiency with which the compressor raises the pressure of the working fluid.
The isentropic efficiency of a turbine is the ratio of the actual work output to the ideal work output, assuming an isentropic process. It represents the efficiency with which the turbine extracts work from the working fluid.
Starting from the expression pr constant (pressure ratio constant), we can derive the relationship between temperatures at different points in an isentropic process. By applying the ideal gas law and rearranging the equation, we obtain the relationship T1/T2 = (P1/P2)^((k-1)/k), where T1 and T2 are the temperatures at points 1 and 2, and P1 and P2 are the pressures at points 1 and 2, respectively. This equation shows that the temperature ratio is related to the pressure ratio by the specific heat ratio (k) of the gas.
To calculate the back work ratio and thermal efficiency for the given cycle, we need to determine the specific heat capacity (Cp), specific gas constant (R), and specific heat ratio (k) of the air. With these values, we can calculate the back work ratio (BWR) as the ratio of the work required for compression to the work produced by the turbine. The thermal efficiency (ηth) is the ratio of the net work output to the heat input.
To improve the thermal efficiency of this process, several approaches can be considered. One option is to increase the intercooling efficiency to reduce the temperature at the compressor inlet. Another possibility is to enhance the combustion process to achieve higher temperatures and better combustion efficiency. Additionally, improving the turbine's isentropic efficiency would increase the work output. Utilizing waste heat recovery techniques, such as a bottoming cycle or combined heat and power (CHP) systems, can also boost the overall thermal efficiency by utilizing the heat from the exhaust gases for additional purposes.
Know more about isentropic process here:
https://brainly.com/question/13001880
#SPJ11
A 6Y-ft diameter circular clarifier is 10-ft deep. It handles 2.8 MGD. Compute the hydraulic loading in cu ft per hour per square ft (also known as the overflow rate) to the nearest 0.1 (ft per hr per ft?). The hydraulic loading rate (overflow rate) is (ft per hr per ft).
The hydraulic loading rate is 0.1 . Overflow rate or hydraulic loading rate is defined as the rate at which water or wastewater is passing over per unit area of a settling basin.
It is the ratio of flow rate to the surface area of the clarifier basin.
The hydraulic loading in cubic feet per hour per square foot, commonly referred to as the overflow rate, can be calculated using the following formula: Hydraulic loading rate (ft/hr)
= Q / (A * T)
Where,
Q = flow rate (in MGD)A
= area of the clarifier (in square feet)T
= detention time (in hours)In this scenario,
Q = 2.8 MGD,
A = (π/4) * d²
= (π/4) * 6²
= 28.27 ft², and T
= 10 ft / 12 ft/hr
= 0.83 hr
Therefore, Hydraulic loading rate
= 2.8 / (28.27 * 0.83)
= 0.123 (ft/hr)/ft^2, rounded off to the nearest 0.1
Therefore, the hydraulic loading rate is 0.1 .
To know more about area visit :
https://brainly.com/question/30579390
#SPJ11
. Determine the instantaneous rate of change at x=−1. b. Determine the average rate of change on the interval −1≤x≤2
a.) The instantaneous rate of change at x = -1 for the function f(x) = 2x² - 3x + 1 is -7.
b.) The average rate of change on the interval [-1, 2] for the function f(x) = 2x² - 3x + 1 is -4/3.
a)
Instantaneous rate of change of a function can be defined as the rate of change of a function at a particular point.
It is also called the derivative of a function.
The instantaneous rate of change at x = -1 is given by:
f'(-1) = (d/dx) f(x)|x=-1
Given the function f(x) = 2x² - 3x + 1,
Using the power rule of differentiation, we get
f'(x) = d/dx (2x² - 3x + 1) = 4x - 3 At x = -1,
we have f'(-1) = 4(-1) - 3 = -7
Therefore, the instantaneous rate of change at x = -1 is -7.
b)
The average rate of change of a function over a given interval [a, b] is the ratio of the change in y-values (Δy) to the change in x-values (Δx) over the interval. It is given by:
(f(b) - f(a))/(b - a)
For the function f(x) = 2x² - 3x + 1,
evaluate (f(2) - f(-1))/(2 - (-1)) = (8 - 12)/(3) = -4/3
Therefore, the average rate of change on the interval [-1, 2] is -4/3.
To know more about instantaneous rate of change visit:
https://brainly.com/question/30760748
#SPJ11
Find the instantaneous rate of change at the zeros for the function: y = x² - 2x² - 8x² + 18x-9
The instantaneous rate of change at the zeros of the function y = x² - 2x² - 8x² + 18x - 9 is 18.
To find the instantaneous rate of change at the zeros of the function, we first need to determine the zeros or roots of the function, which are the values of x that make y equal to zero.
Given the function y = x² - 2x² - 8x² + 18x - 9, we can simplify it by combining like terms:
y = -9x² + 18x - 9
Next, we set y equal to zero and solve for x:
0 = -9x² + 18x - 9
Factoring out a common factor of -9, we have:
0 = -9(x² - 2x + 1)
0 = -9(x - 1)²
Setting each factor equal to zero, we find that x - 1 = 0, which gives us x = 1.
Now that we have the zero of the function at x = 1, we can find the instantaneous rate of change at that point by evaluating the derivative of the function at x = 1. Taking the derivative of y = x² - 2x² - 8x² + 18x - 9 with respect to x, we get:
dy/dx = 2x - 4x - 16x + 18
Evaluating the derivative at x = 1, we have:
dy/dx = 2(1) - 4(1) - 16(1) + 18 = 2 - 4 - 16 + 18 = 0
Therefore, the instantaneous rate of change at the zero of the function is 0.
Learn more about : Function
brainly.com/question/26304425
#SPJ11
Determine the moment about point P if F = 100 N and the angle alpha is 60 degrees. F P -2 m- 1m
Answer: The moment about point P is equal to 100√3 N.
The moment about point P can be determined using the formula:
Moment = Force × Distance × sin(θ)
Given that the force F is 100 N and the angle α is 60 degrees, we need to find the moment about point P.
To calculate the moment, we need to know the distance between point P and the line of action of the force F. In this case, the distance is given as 2 m.
Now, let's substitute the values into the formula:
Moment = 100 N × 2 m × sin(60 degrees)
We can calculate the value of sin(60 degrees) as √3/2:
Moment = 100 N × 2 m × √3/2
Simplifying further:
Moment = 100 N × √3
The moment about point P is equal to 100√3 N.
To learn more about moment about point :
https://brainly.com/question/30825009
#SPJ11
P9.32 Determine the vertical deflection and rotation at point B. I=5500in4. rrowiem Y.s ∠
Therefore, the vertical deflection and rotation at point B are 1.08 in and 0.0067 rad (or) 0.383° respectively Given, Load on beam=50k/ft Length of beam=12ft Elastic modulus =30*10^6 psiI=5500in^4.
The formula for vertical deflection under the load is given asδy=wl^4/8EI. Where, w = load per unit length l = length of the beam E = Elastic modulus I = Moment of Inertiaδy = wl^4/8EIδy = 50k/ft × 12ft × 12^4in^4 / (8 × 30 × 10^6 psi × 5500 in^4)δy = 1.08 in.
The formula for the rotation of the beam under the load is given asθ=wl^3/3EIθ = 50k/ft × 12ft × 12^3in^3 / (3 × 30 × 10^6 psi × 5500 in^4)θ = 0.383° (or) 0.0067 rad.
To know more about deflection visit:
https://brainly.com/question/31967662
#SPJ11
According to Lewis theory, a Lewis acid is an,
(A) proton donor.
(B) electron-pair donor.
(C) proton acceptor.Which acid is likely to result in the greatest percent ionization in aqueous solution?
the acid that is likely to result in the greatest percent ionization in aqueous solution would be a strong acid such as hydrochloric acid (HCl), sulfuric acid (H2SO4), or nitric acid (HNO3). These acids readily dissociate in water, leading to a high degree of ionization.
According to Lewis theory, a Lewis acid is an electron-pair acceptor. This means that a Lewis acid is a species that can accept a pair of electrons from another species. Lewis acids are characterized by having an electron-deficient atom or ion that can form a coordinate bond with a Lewis base, which is the electron-pair donor.
In the given choices, (B) electron-pair donor is the correct answer for the definition of a Lewis acid. A Lewis acid is not a proton donor (A) or a proton acceptor (C), as those terms are associated with Bronsted-Lowry theory, which focuses on the transfer of protons (H+ ions) in acid-base reactions.
To determine which acid is likely to result in the greatest percent ionization in aqueous solution, we need to consider the strength of the acid. Strong acids are more likely to undergo complete ionization in water, resulting in a higher percent ionization.
Strong acids are typically those that completely dissociate in water to produce a large number of H+ ions. Examples of strong acids include hydrochloric acid (HCl), sulfuric acid (H2SO4), and nitric acid (HNO3).
Weak acids, on the other hand, only partially ionize in water, resulting in a lower percent ionization. Examples of weak acids include acetic acid (CH3COOH) and formic acid (HCOOH).
Therefore, the acid that is likely to result in the greatest percent ionization in aqueous solution would be a strong acid such as hydrochloric acid (HCl), sulfuric acid (H2SO4), or nitric acid (HNO3). These acids readily dissociate in water, leading to a high degree of ionization.
To learn more about Lewis theory:
https://brainly.com/question/28299444
#SPJ11
Consider a market in which two firms are engage in quantity competition a la Cournot, but with differentiated products. As in the standard model each firm = 1,2 has a cost function TC(q) F+cq;. However, now each firm may recieve a different price for it's output.
In particular, firm 1 recieves the price Pa-bq-d q₂ and firm 2 recieves the price
dP (a) Use the fact that MR1 P+ to find an expression for MR in terms of a, b, d, qi and 42.
(b) Use your answer from part (a) to find firm 1's reaction function.
(c) Find a simplified expression for each firm's equilibrium output, q
(d) Find each firm's equilibrium price, P. Use your expression for P to find a simplified expression for Pc, the firms markup over marginal cost.
(a) [tex]MR = Pa - 2bq - d(q1 + q2)[/tex]
(b) Firm 1's reaction function: [tex]q1 = (Pa - c - bq2 - d(q1 + q2))/(2b)[/tex]
(c) Equilibrium outputs: [tex]q1 = (Pa - c - bq2 - d(q1 + q2))/(3b + d)[/tex] and [tex]q2 = (Pa - c - bq1 - d(q1 + q2))/(3b + d)[/tex]
(d) Equilibrium prices: [tex]P = Pa - bq - d(q1 + q2)[/tex], where [tex]q = q1 + q2[/tex]
[tex]Pc = (2bPa - 3bc - 3b^2q - 3bd(q1 + q2))/(3b + d)[/tex]
(a) The marginal revenue (MR) is derived from the price (Pa) received by Firm 1, considering the cost elements and the quantity of output. It is given by [tex]MR = Pa - 2bq - d(q1 + q2)[/tex], where q1 and q2 represent the quantities produced by Firm 1 and Firm 2, respectively.
(b) Firm 1's reaction function represents the optimal output level (q1) that Firm 1 chooses based on the given price, costs, and the quantity produced by Firm 2 (q2). The reaction function is derived by setting MR equal to marginal cost (MC). By equating MR to MC, we can solve for q1, resulting in the equation [tex]q1 = (Pa - c - bq2 - d(q1 + q2))/(2b)[/tex].
(c) The equilibrium outputs for both firms are determined simultaneously. The equilibrium output for Firm 1 (q1) is calculated by substituting the reaction function from part (b) into the expression for Firm 1's reaction function. Similarly, the equilibrium output for Firm 2 (q2) is calculated by substituting the reaction function into the expression for Firm 2's reaction function.
(d) The equilibrium price (P) is determined by subtracting the total quantity produced (q1 + q2) from the price (Pa), taking into account the quantity-related terms (bq) and the cost of differentiation (d). Using the expression for P, we can calculate the firms' markup over marginal cost (Pc) by subtracting the marginal cost (MC = c) from the equilibrium price.
Learn more about 1's reaction function
brainly.com/question/14250690
#SPJ11
Simplify the following the boolean functions, using three-variable K-maps: F(x, y, z) = (0,2,6,7) m OAF=xy+xz+yz OB.F=xy+xz' OC.F=x² + y² O D.F=z² + xy 4
To simplify the given boolean functions using three-variable K-maps, let's consider each function separately.
F(x, y, z) = (0,2,6,7)
The truth table for this function is as follows:
| x | y | z | F |
|---|---|---|---|
| 0 | 0 | 0 | 1 |
| 0 | 0 | 1 | 0 |
| 0 | 1 | 0 | 1 |
| 0 | 1 | 1 | 1 |
| 1 | 0 | 0 | 1 |
| 1 | 0 | 1 | 0 |
| 1 | 1 | 0 | 1 |
| 1 | 1 | 1 | 1 |
Using a three-variable K-map, we can simplify the function F(x, y, z) as F = yz + x.
F(x, y, z) = xy + xz'
The truth table for this function is as follows:
| x | y | z | F |
|---|---|---|---|
| 0 | 0 | 0 | 0 |
| 0 | 0 | 1 | 0 |
| 0 | 1 | 0 | 0 |
| 0 | 1 | 1 | 0 |
| 1 | 0 | 0 | 1 |
| 1 | 0 | 1 | 1 |
| 1 | 1 | 0 | 1 |
| 1 | 1 | 1 | 1 |
Using a three-variable K-map, we can simplify the function F(x, y, z) as F = x.
F(x, y, z) = x² + y²
This function cannot be simplified using a three-variable K-map as it represents the sum of squares of two variables.
F(x, y, z) = z² + xy
This function cannot be simplified using a three-variable K-map as it represents the sum of squares of one variable and the product of two variables.
Please note that K-maps are primarily used for simplifying boolean functions with up to four variables. For functions with more variables, alternative methods such as algebraic manipulation or computer-based algorithms may be employed.
To learn more about truth table visit:
brainly.com/question/30588184
#SPJ11
Compute the following: 17(−5)+15−(−4) +(−6)−5 Select one: a. −85 b. −77 c. −65 d. 65
The expression 17(-5)+15-(-4)+(-6)-5= -85+15+4-6-5 = -77.The answer is -77.
To simplify the expression, we need to follow the order of operations (PEMDAS), which means we perform the operations inside the parentheses first, then the exponents, followed by multiplication and division (from left to right), and finally addition and subtraction (from left to right)-
In this expression, there are no exponents or multiplication/division, so we only need to focus on the addition and subtraction-
We start from left to right, adding -85 and 15 to get -70-
We then add 4 to get -66-
We then subtract 6 from -66 to get -72-
Finally, we subtract 5 from -72 to get -77
To know more about expression visit:
https://brainly.com/question/28170201
#SPJ11
The distance traveled by a falling object is modeled by the equation below, where s is the distance fallen, g is gravity, and t is time.
If s is measured in meters and t is measured in seconds, what units is g measured in?
Answer: The units of g are meters/second^2
Step-by-step explanation: The distance fallen by a falling object is modeled by the equation s=1/2gt^2, where g is the acceleration due to gravity. The units of s are meters and the units of t are seconds. Therefore, the units of g can be found by rearranging the equation to solve for g, which gives g=2s/t^2. Substituting the units of s and t, we get g=2 meters/second^2.
Therefore, the units of g are meters/second^2.
A fully penetrating unconfined well of 12 in. diameter is pumped at a rate of 1 ft³/sec. The coefficient of permeability is 750 gal/day per square foot. The drawdown in an observation well located 200 ft away from the pumping well is 10 ft below its original depth of 150 ft. Find the water level in the well
Therefore, the water level in the well is 160 ft.
A fully penetrating unconfined well of 12 in. diameter is pumped at a rate of 1 ft³/sec.
The coefficient of permeability is 750 gal/day per square foot.
The drawdown in an observation well located 200 ft away from the pumping well is 10 ft below its original depth of 150 ft.
To find: The water level in the well.
Let the water level in the well be h ft.
The discharge of the well (Q) = 1 ft³/sec. = 7.48 gallons/sec.
The radius of the well (r) = 12/24 = 0.5 ft.
The distance between the well and observation well (r) = 200 ft.
The original water level in the observation well = 150 ft.
The drawdown (s) = 10 ft.
The coefficient of permeability (k) = 750 gal/day per square foot.
Q = 7.48 gallons/sec.
s = h - 150ft.
k = 750 gallons/day/ft².
Convert k into feet by the following conversion,1 day = 24 hours 1 hour = 60 min 1 min = 60 sec 1 day = 86400 sec
So, k = (750/86400) ft/sec =(0.00868055) ft/sec
Now, we can use Theis' formula to find the value of h.
The Theis' formula is given by,
s = (Q/4πT) W(u) ------(1)where, T is the transmissivity, W(u) is the well function, and u is the distance between the pumping well and observation well such that u = r²S/4Tt, where,
S is the storativity, and t is the time
.π = 3.14
Using the above values in equation (1), we get10 = [7.48/(4 x 3.14 x T)] W(u) -------(2)T = k x b
where, b is the thickness of the aquifer, and k is the coefficient of permeability.
T = 0.00868055 ft/sec x 150 ftT = 1.3021 ft²/sec
Substituting the value of T in equation (2),10 = [7.48/(4 x 3.14 x 1.3021)] W(u)
W(u) = 0.1416
For u > 1, W(u) can be approximated as, W(u) = ln(u) + 0.57721 + 0.0134u² + 0.76596u² + 0.25306u³ + ........(3)
Here, u = r²S/4Tt. We don't know the value of S yet, so we can use a trial and error method to find the value of S and u.
Using S = 0.0002 for trial, we get u = 2.76.
Using equation (3),W(u) = ln(2.76) + 0.57721 + 0.0134(2.76)² + 0.76596(2.76)³W(u) = 0.2419
Now, substituting the values of T and W(u) in equation (2), we get10 = [7.48/(4 x 3.14 x 1.3021)] x 0.2419T = 1.3021 ft²/sec
Hence, the water level in the well is given by,
h = s + 150h = 10 + 150 = 160 ft
Therefore, the water level in the well is 160 ft.
To know more about permeability visit:
https://brainly.com/question/32006333
#SPJ11
Find the general aolution of 2y′′′+7y′′+4y′−4y=0, if m1=1/2 is a root of ita characteriatio equation.
The general solution of the given third-order linear homogeneous differential equation, with m1 = 1/2 as a root of the characteristic equation, can be summarized as:
y(x) = c1 * e^(1/2 * x) + c2 * e^(-2 * x) + c3 * e^(-2 * x)
Here, c1, c2, and c3 are arbitrary constants.
To find the general solution of the differential equation 2y′′′ + 7y′′ + 4y′ − 4y = 0, let's assume that m1 = 1/2 is a root of its characteristic equation.
The characteristic equation associated with the given differential equation is obtained by substituting y = e^(mx) into the equation and setting it equal to zero:
2(m^3) + 7(m^2) + 4m - 4 = 0
Since m1 = 1/2 is a root of the characteristic equation, we can rewrite the equation as:
(2m - 1)(m^2 + 4m + 4) = 0
This gives us two more roots: m2 = -2 and m3 = -2.
The general solution of a third-order linear homogeneous differential equation is given by:
y(x) = c1 * e^(m1 * x) + c2 * e^(m2 * x) + c3 * e^(m3 * x)
Plugging in the values of the roots, the general solution becomes:
y(x) = c1 * e^(1/2 * x) + c2 * e^(-2 * x) + c3 * e^(-2 * x)
Therefore, the general solution of the given differential equation, with m1 = 1/2 as a root of the characteristic equation, is:
y(x) = c1 * e^(1/2 * x) + c2 * e^(-2 * x) + c3 * e^(-2 * x)
To learn more about differential equations visit : https://brainly.com/question/1164377
#SPJ11
if f is continuos on the interval [3,7] and differentiable on (3.7) and f(3) =1 and f(7)=4, then there is a number c in (3,7) such that slope of the tangent line to the graph of f at (c, f(c)) is equal to
The slope of the tangent line to the graph of f at some point c in the interval (3,7) is equal to 1.
Since f is continuous on the closed interval [3,7] and differentiable on the open interval (3,7), we can apply the Mean Value Theorem.
According to this theorem, if a function is continuous on a closed interval and differentiable on the open interval, then there exists at least one point within the open interval where the instantaneous rate of change (i.e., the derivative) equals the average rate of change over the closed interval.
In this case, the function f is continuous on [3,7] and differentiable on (3,7). The average rate of change between f(3) and f(7) is given by (f(7) - f(3))/(7-3) = (4-1)/(7-3) = 3/4.
Therefore, there exists a number c in the open interval (3,7) where the derivative of f at c equals 3/4.
Since the question asks for the slope of the tangent line at that point, we conclude that the slope of the tangent line to the graph of f at (c, f(c)) is equal to 3/4.
Learn more about slope of the tangent
brainly.com/question/32597734
#SPJ11
(d)
In Malaysia, the monsoon rain causes tremendous challenges to
engineers and
contractors especially when constructing roads at hillsides. The
reasons are
hills are usually subjected to intermittent
The monsoon rain in Malaysia poses significant challenges for engineers and contractors when constructing roads on hillsides.
Here are the reasons for these difficulties:
1. Intermittent Rainfall: During the monsoon season, Malaysia experiences heavy rainfall, which is often unpredictable and occurs in intervals. This intermittent rainfall can disrupt construction activities and cause delays in the road-building process.
2. Erosion and Landslides: The combination of heavy rain and steep hillsides can lead to soil erosion and landslides. The excess water can wash away the soil, destabilizing the slope and making it unsafe for construction. Engineers need to implement proper soil stabilization techniques to prevent erosion and ensure the stability of the road.
3. Drainage Issues: Constructing roads on hillsides requires effective drainage systems to handle the excess water during heavy rainfall. Improper drainage can result in water pooling on the road surface, leading to hazards such as hydroplaning. Engineers need to design and install proper drainage systems to mitigate these risks.
4. Slope Stability: Hillsides are naturally prone to slope instability, and heavy rainfall can exacerbate this issue. Engineers must conduct thorough geotechnical investigations to assess the slope stability before construction begins. Measures like slope reinforcement, retaining walls, and erosion control methods may be necessary to ensure the safety and longevity of the road.
To overcome these challenges, engineers and contractors need to apply proper planning, design, and construction techniques specific to hillside roads. They should consider factors like slope angle, soil type, drainage, and stability measures to ensure the road can withstand the monsoon rain and provide safe transportation for years to come.
Learn more about monsoon rain:
https://brainly.com/question/1085686
#SPJ11
Suppose that the price p, in dollars, and the number of sales, x, of a certain item follow the equation 4p+ 4x+3px =77. Suppose also that p and x are both functions of time, measured in days. Find
dp the rate at which is changing when x=3, p=5, and dp/dt=1.8.
The rate at which x is changing is
(Round to the nearest hundredth as needed.)
Answer : the rate at which x is changing when x=3, p=5, and dp/dt=1.8 is approximately -0.82.
To find the rate at which p is changing when x=3, p=5, and dp/dt=1.8, we can use the given equation 4p+ 4x+3px =77.
First, let's differentiate the equation with respect to time (t) using the chain rule.
d/dt (4p+ 4x+3px) = d/dt(77)
Differentiating each term separately, we get:
4(dp/dt) + 4(dx/dt) + 3(px' + xp') = 0
Now we substitute the given values: x = 3, p = 5, and dp/dt = 1.8 into the equation and solve for dx/dt.
4(1.8) + 4(dx/dt) + 3(5(dx/dt) + 3(5x' + xp') = 0
Simplifying the equation:
7.2 + 4(dx/dt) + 15(dx/dt) + 15x' + 3xp' = 0
Combining like terms:
19.2 + 19(dx/dt) + 15x' + 3xp' = 0
Now we can solve for dx/dt, the rate at which x is changing:
19(dx/dt) + 15x' + 3xp' = -19.2
Dividing through by 19:
(dx/dt) + (15/19)x' + (3/19)xp' = -1.01
Rounding to the nearest hundredth:
dx/dt = -0.82
Therefore, the rate at which x is changing when x=3, p=5, and dp/dt=1.8 is approximately -0.82.
To learn more about differentiation calculations :
https://brainly.com/question/33481586'
#SPJ11
a)Rectangular Approximation 1a. Sketch the graph of f(x)=0.2(x−3) ^2 (x+1). Shade the area bounded by f(x) and the x-axis on the interval [−1,2] b)Approximate the area of the shaded region using six rectangles of equal width and right endpoints. Draw the rectangles on the figure and show your calculations. Round your final answer to three decimal places
The area of the shaded region using six rectangles of equal width and right endpoints. Rounded to three decimal places we get 1.165.
(a) Sketching the Graph and shading the area bounded by f(x) and x-axis on the interval [−1, 2]:
The graph of the function f(x) = 0.2(x−3)^2(x+1) is shown below:
Area Bounded by f(x) and the x-axis on the interval [−1, 2] is shown in the figure below:
(b) Rectangular Approximation of the shaded region using six rectangles of equal width and right endpoints:
For rectangular approximation of the shaded region using six rectangles of equal width and right endpoints, we have to divide the interval [−1, 2] into six subintervals of equal width. Therefore, we getΔx= (2 - (-1))/6= 1/2
Then, the endpoints of the subintervals are shown in the following table:xi-1xi1/2-1/2+ xi1-1/2+ xi1 1/2+ xi+1
The height of each rectangle is determined by the function f(x) = 0.2(x−3)^2(x+1). The table below shows the function value for each endpoint:
Then, the area of each rectangle is given by the function value multiplied by the width:
Therefore, the area of shaded region using six rectangles of equal width and right endpoints is given by:
Simplify the expression to get:
Thus, the area of shaded region using six rectangles of equal width and right endpoints is 1.165. Rounded to three decimal places, we get 1.165.
Learn more about decimal places
https://brainly.com/question/30650781
#SPJ11
The area of the shaded region using six rectangles of equal width and right endpoints. Rounded to three decimal places we get 1.165.
(a) Sketching the Graph and shading the area bounded by f(x) and x-axis on the interval [−1, 2]:
The graph of the function [tex]f(x) = 0.2(x−3)^2(x+1)[/tex] is shown below:
Area Bounded by f(x) and the x-axis on the interval [−1, 2] is shown in the figure below:
(b) Rectangular Approximation of the shaded region using six rectangles of equal width and right endpoints:
For rectangular approximation of the shaded region using six rectangles of equal width and right endpoints, we have to divide the interval [−1, 2] into six subintervals of equal width. Therefore, we getΔx= (2 - (-1))/6= 1/2
Then, the endpoints of the subintervals are shown in the following table:xi-1xi1/2-1/2+ xi1-1/2+ xi1 1/2+ xi+1
The height of each rectangle is determined by the function
[tex]f(x) = 0.2(x−3)^2(x+1).[/tex]The table below shows the function value for each endpoint:
Then, the area of each rectangle is given by the function value multiplied by the width:
Therefore, the area of shaded region using six rectangles of equal width and right endpoints is given by:
Simplify the expression to get:
Thus, the area of shaded region using six rectangles of equal width and right endpoints is 1.165. Rounded to three decimal places, we get 1.165.
Learn more about decimal places:
brainly.com/question/30650781
#SPJ11
Question: Determine the equation of motion, Please show work step by step
A 8 pound weight stretches a spring by 0.5 feet. The mass is then released from an initial position 1 foot below the equilibrium position with an initial upward velocity of 24 feet per second. The surrounding medium offers a damping force of= 2.5 times the instantaneous velocity.
The equation of motion for this scenario is: dv/dt = (515.2 * x - 2.5 * v - 257.6) / 0.248.
To determine the equation of motion for this scenario, we need to consider the forces acting on the system. The weight exerts a gravitational force of 8 pounds, which can be converted to 8 * 32.2 = 257.6 lb*ft/s^2. The spring force opposes the weight and is given by Hooke's Law, which states that the force exerted by a spring is proportional to the displacement from its equilibrium position. The equation for the spring force is F_spring = k * x, where k is the spring constant and x is the displacement.
Since the weight stretches the spring by 0.5 feet, we can substitute the given values into the equation: 257.6 = k * 0.5. Solving for k, we find k = 515.2 lb/ft.
Next, we can consider the damping force. The damping force is given by F_damping = -2.5 * v, where v is the velocity. The negative sign indicates that the damping force opposes the velocity.
Now we can write the equation of motion: m * a = F_spring + F_damping + F_gravity, where m is the mass and a is the acceleration.
The mass is not given, but we can solve for it using the weight: 8 lb = m * 32.2 ft/s^2. Solving for m, we find m = 8 / 32.2 = 0.248 lb*s^2/ft.
With all the values known, we can write the equation of motion as: 0.248 * dv/dt = 515.2 * x - 2.5 * v - 257.6.
Simplifying the equation further, we have: dv/dt = (515.2 * x - 2.5 * v - 257.6) / 0.248.
This equation describes the motion of the system. To solve it, we can use numerical methods or techniques such as Laplace transforms, depending on the desired level of accuracy and complexity.
Learn more about Laplace transforms from:
https://brainly.com/question/29583725
#SPJ11
Establish the dynamic equations of free vibration for the SDOF and Favstems.
The dynamic equations of free vibration for a single degree of freedom (SDOF) system and a forced and damped vibration system (FAVSTEMS) can be established as follows:
1. SDOF System:
The equation of motion for an undamped SDOF system subjected to free vibration can be written as:
m * x''(t) + k * x(t) = 0
Where:
m is the mass of the system,
x(t) is the displacement of the mass at time t,
k is the stiffness of the system, and
x''(t) denotes the second derivative of x(t) with respect to time.
2. FAVSTEMS:
The equation of motion for a damped FAVSTEMS subjected to free vibration can be expressed as:
m * x''(t) + c * x'(t) + k * x(t) = 0
Where:
m is the mass of the system,
x(t) is the displacement of the mass at time t,
c is the damping coefficient, and
x'(t) denotes the first derivative of x(t) with respect to time.
In both cases, the equations describe the balance of forces acting on the system. The SDOF equation represents an undamped system, while the FAVSTEMS equation incorporates the effect of damping.
These equations can be solved analytically to obtain the natural frequency and mode shapes of the system. The solutions will depend on the specific parameters of the system (mass, stiffness, and damping) and the initial conditions (initial displacement and velocity). By solving these equations, one can analyze the behavior of the system, including its natural frequencies, transient response, and steady-state response.
To know more about SDOF, visit;
https://brainly.com/question/20937902
#SPJ11
An Al-Cu alloy containing 4 wt% of Cu, of the condition referred to in (a)(iii) above, can be a strong material for aerospace applications. (i) Explain the mechanism by which strengthening is achieved in this alloy, and show that the strength achieved is given by To = aGb/L where a is a constant of around 1, G = shear modulus, b = Burgers vector, and (6 marks) L is a microstructural spacing. What exactly is L in this case? (ii) In addition to the strengthening mechanism described in (b)(i) above, what other strengthening mechanism(s) is(are) present in the Al-Cu alloy? Explain briefly (4 marks) the mechanism(s).
Al-Cu alloy is a kind of alloy that contains 4% Cu. A strong aerospace material can be made from this alloy. There are two ways to strengthen this alloy - work hardening and phase hardening.
(i) Mechanism by which the alloy is strengthened: Strengthening mechanisms can be divided into two categories: work hardening and phase hardening. Work hardening involves cold-rolling the metal to raise the number of defects in the lattice and hence the dislocation density. The strength of the material increases as the density of dislocations increases. In contrast, phase hardening depends on the existence of a strong second phase in the alloy. In Al-Cu alloy, we can combine these two mechanisms. The strength of a solid is proportional to the number of defects in the lattice. One method to increase the number of defects is to decrease the distance between the defects. The amount of stress required to dislocate a portion of the lattice depends on the dislocation density and their mean free path, as well as the strength of the dislocation obstacle. The strength of a solid is proportional to the number of defects in the lattice. One method to increase the number of defects is to decrease the distance between the defects. The amount of stress required to dislocate a portion of the lattice depends on the dislocation density and their mean free path, as well as the strength of the dislocation obstacle. In this case, L is the average distance between the Cu-rich precipitates in the Al matrix.
(ii) Other strengthening mechanisms in Al-Cu alloy include:
Solution hardening: In alloys, a solid solution is a homogenous single-phase alloy made up of more than one element. Copper in the Al-Cu alloy is a substitutional impurity, implying that it occupies Al lattice sites. The smaller copper atoms cause the lattice to distort as they replace Al atoms. This lattice distortion raises the energy necessary to move dislocations, which strengthens the material. This method of strengthening is known as solution strengthening.
Precipitation hardening: Copper precipitates from the supersaturated Al-Cu solid solution and forms Cu-rich precipitates. As these precipitates grow, they cause the lattice distortion to increase, which raises the energy necessary to move dislocations. This type of strengthening is known as precipitation hardening.
Learn more about alloy visit:
brainly.com/question/1759694
#SPJ11
Soils of a recessional moraine would be expected to be
medium dense, clean, well-graded sand, and do not make good
foundation bearing soil deposits for spread footing
foundations.
true or false
The statement "Soils of a recessional moraine would be expected to be medium dense, clean, well-graded sand, and do not make good foundation bearing soil deposits for spread footing foundations" is False.
A moraine is any glacially formed accumulation of unconsolidated debris (soil and rock) that occurs in both currently and formerly glaciated regions, such as those areas that are covered by ice sheets or glaciers at any point in the last several million years.
Moraines are made up of glacial sediments ranging in size from clay to boulders.
When a glacier melts, it leaves behind a variety of soil types, including boulder clay, silt, sand, and other deposits.
The moraines' soil quality, on the other hand, is largely dependent on their formation process, topography, and glacier type.
For instance, the moraines produced by continental glaciers are characterized by a mix of poorly to moderately sorted clay, sand, and gravel with various types of rocks.
The soils of a recessional moraine would be expected to be typically poorly graded till with high plasticity and, therefore, would make a good foundation bearing soil deposits for spread footing foundations.
Therefore, the statement "Soils of a recessional moraine would be expected to be medium dense, clean, well-graded sand, and do not make good foundation bearing soil deposits for spread footing foundations" is False.
Know more about Soils here:
https://brainly.com/question/1286340
#SPJ11
structure that gives rise to a partial The peptide C-N bonds are considered rigid (do not rotate) because of their characteristic
The main structure that gives rise to a partial peptide C-N bonds is considered rigid because of their characteristic is known as the peptide bond. The peptide bond is a special type of covalent bond that is formed between two amino acids during protein synthesis.
The structure that gives rise to a partial rigidity of the peptide C-N bonds is the main chain of the protein molecule. The main chain of the protein molecule consists of a series of peptide units, each consisting of an amino acid linked to its neighboring amino acids by peptide bonds. The peptide bond is the covalent bond that joins the amino acids in the protein molecule. It is formed by a reaction between the carboxyl group of one amino acid and the amino group of the next amino acid. The peptide bond is a planar bond that gives rise to a partial rigidity of the protein backbone. The rotation about the peptide bond is restricted because of the partial double bond character of the bond. The peptide bond has a bond length of 1.33 Å and an angle of 120° between the C-N and C-C bonds. The planarity of the peptide bond is due to the resonance between the two canonical forms of the peptide bond.
In conclusion, the partial rigidity of the peptide C-N bonds is due to the planarity of the peptide bond, which is a covalent bond that joins the amino acids in the protein molecule. The peptide bond has a bond length of 1.33 Å and an angle of 120° between the C-N and C-C bonds. The planarity of the peptide bond is due to the resonance between the two canonical forms of the peptide bond.
learn more about covalent bond visit:
brainly.com/question/19382448
#SPJ11
Listen Using the Thomas Graphical Method, the range of BOD rate constant (k) in base e from the following data is estimated be nearly. Submit your "detail work" including the graph for partial credit. (CLO 3) Time (day) 2 BOD (mg/L) 120 5 210 1) k 0.175-0.210/day 2) K 0.475-0.580 /day 3) k=0.275-0.380/day 10 262 20 279 35 280
The estimated range of the BOD rate constant (k) in base e, using the Thomas Graphical Method, is approximately 0.175-0.210/day based on the given data.
The Thomas Graphical Method is used to estimate the range of the BOD rate constant (k) based on the given data. BOD stands for Biological Oxygen Demand, which measures the amount of dissolved oxygen needed by microorganisms to break down organic matter in water.
To estimate the range of k, we plot the BOD values against time on a graph. From the given data, we have:
Time (day) BOD (mg/L)
2 120
5 210
10 262
20 279
35 280
By plotting these points on a graph, we can see the general trend of BOD decreasing over time. The range of k can be estimated by drawing a line that best fits the data points.
Based on the graph, the range of k in base e is approximately 0.175-0.210/day. This means that the BOD rate constant falls within this range for the given data.
Remember, the Thomas Graphical Method provides an estimation, and the actual value of k may vary. The graph is essential for visualizing the trend and estimating the range.
learn more about constant from given link
https://brainly.com/question/27983400
#SPJ11
In curve fitting, the parameter values are estimated such that error is minimized. a.sum of squares of error is minimized. b.square of error is minimized. c.sum of error is minimized.
In curve fitting, the parameter values are estimated such that the sum of squares of error is minimized.
In curve fitting, the parameters of a function are found to best fit the provided data.
The goal of curve fitting is to discover a mathematical model that meets as closely as possible to the empirical dataset.
The majority of fitting algorithms try to find the ideal model parameters that minimize the error between the data and the model.
In curve fitting, the parameter values are estimated in such a way that the sum of squares of error is minimized.
For instance, if a model produces a prediction of 3, and the actual value is 5, then the error is 2.
The square of this error is 4.
The curve-fitting algorithm adds up all of these squared errors and attempts to find the values of the model parameters that reduce this sum to the least possible value.
To know more about curve fitting visit:
https://brainly.com/question/33368286
#SPJ11
A truck can carry a maximum of 42000 pounds of cargo. How many cases of cargo can it carry if half of the cases have an average (arithmetic mean) weight of 10 pounds and the other half have an average weight of 30 pounds
The truck can carry a total of 840 cases of cargo.
We need to find the total weight of the cargo the truck can carry. Since the truck's maximum capacity is 42,000 pounds, we can divide this weight equally between the two types of cases. Let's calculate the total weight of the cargo by considering the two types of cases. Half of the cases have an average weight of 10 pounds, and the other half have an average weight of 30 pounds. First, let's find the total weight of the cases with an average weight of 10 pounds:Number of cases with 10-pound average weight = 42000 / 10 = 4200 cases
Total weight of these cases = 4200 cases * 10 pounds/case = 42,000 pounds
Next, let's find the total weight of the cases with an average weight of 30 pounds:
Number of cases with 30-pound average weight = 42000 / 30 = 1400 cases
Total weight of these cases = 1400 cases * 30 pounds/case = 42,000 pounds
Now, we add the total weight of both types of cases to get the overall cargo weight the truck can carry:
Total cargo weight = 42,000 pounds + 42,000 pounds = 84,000 pounds
Finally, we divide the total cargo weight by the average weight of each case to find the total number of cases the truck can carry:
Number of cases = 84,000 pounds / 20 pounds/case = 4,200 cases
Learn more about Total weight of the cargo
brainly.com/question/31712177
#SPJ11
Triangle A B C is shown. Side A B has a length of 12. Side B C has a length of x. Side A C has a length of 15. The value of x must be greater than ________.
Answer:
Step-by-step explanation:
Given that,
AB = 12
BC= X
AC = 15
Therefore, To form a triangle the difference between two sides should be lesser than the third side
So,
X should be greater than 15 - 12 = 3
X > 3