The major organic product of the given reaction: Mechanism of the catalytic hydrogenation reaction shown below:In the above reaction, H2 gas is passed through a Ni catalyst at 25 atm and a temperature of around 150°C. The alkene (1-hexene) gets hydrogenated in the presence of the catalyst.
This results in the alkene losing its double bond, adding H2 and creating an alkane (hexane). The mechanism is as follows: The first step involves the adsorption of H2 molecule onto the metal surface (Ni) of the catalyst.Step 2: The hydrogen molecule then gets dissociated into two atoms. The hydrogen atoms then get adsorbed onto the surface of the catalyst.
The alkene then gets adsorbed onto the surface of the catalyst by forming a pi-complex with the metal catalyst.Step 5: One of the hydrogen atoms from the surface of the catalyst then gets added to one carbon of the alkene, while the second hydrogen atom gets added to the second carbon of the alkene. This creates a tetrahedral intermediate.Step 6: The intermediate then gets de-sorbed from the surface of the catalyst. This regenerates the catalyst and forms the alkane as the final product. In the above reaction, the given alkene is hydrogenated by catalytic hydrogenation. Catalytic hydrogenation is an industrial process that is used for the reduction of alkene groups in alkenes. Hydrogenation is an addition reaction in which an alkene gets reduced to an alkane by adding hydrogen to it in the presence of a catalyst.
To know more about organic product visit :
https://brainly.com/question/30328741
#SPJ11
7. Solve the equation dy y² dx x² y 1 with the homogenous substitution method. Solve explicitly. X
The solution to the given equation using the homogeneous substitution method is:
(1/4) * x⁴u² + x + x²u²v + ln|x| = vx + C
To solve the given equation using the homogeneous substitution method, we need to make a substitution to simplify the equation.
Let's start by substituting y = vx, where v is a new variable.
Differentiating both sides of the equation with respect to x using the product rule, we get:
dy/dx = v + x * dv/dx
Now, substituting y = vx and dy/dx = v + x * dv/dx into the given equation, we have:
v + x * dv/dx = (vx)² / (x² * vx + 1)
Simplifying further, we get:
v + x * dv/dx = v²x² / (x³v + 1)
To proceed, we'll divide both sides of the equation by x²v²:
(v + x * dv/dx) / (x²v²) = 1 / (x³v + 1)
Now, we can simplify the left side of the equation. Dividing each term by v², we get:
(1/v²) + (x * dv/dx) / (x²v²) = 1 / (x³v + 1)
Next, we'll substitute u = v/x:
(1/v²) + (x * dv/dx) / (x²v²) = 1 / (x³(u * x) + 1)
(1/v²) + (x * dv/dx) / (x²v²) = 1 / (x³u² + 1)
Simplifying further:
(1/v²) + (x * dv/dx) / (x²v²) = 1 / (x³u² + 1)
(1/v²) + (1/x * dv/dx) / (xv) = 1 / (x³u² + 1)
(1/v²) + (1/x * dv/dx) / (v) = 1 / (x³u² + 1)
We can simplify this equation even further by multiplying each term by v²:
1 + (1/x * dv/dx) = v / (x³u² + 1)
Now, we can see that this equation is separable. We'll move the (1/x * dv/dx) term to the other side:
1 = v / (x³u² + 1) - (1/x * dv/dx)
Multiplying through by (x³u² + 1), we have:
x³u² + 1 = v - (1/x * dv/dx)(x³u² + 1)
Expanding and simplifying:
x³u² + 1 = v - x²u² * dv/dx - (1/x * dv/dx)
Rearranging the terms:
x³u² + 1 + x²u² * dv/dx + (1/x * dv/dx) = v
Now, we can integrate both sides of the equation with respect to x:
$∫ (x³u² + 1 + x²u² \frac{dv}{dx} + (\frac{1}{x} \times \frac{dv}{dx})) dx = ∫ v dx$
Integrating each term separately, we have:
$∫ x³u² dx + ∫ dx + ∫ x²u² \frac{dv}{dx} dx + ∫ (\frac{1}{x}\times \frac{dv}{dx}) dx = ∫ v dx$
This simplifies to:
(1/4) * x⁴u² + x + x²u²v + ln|x| = vx + C
where C is the constant of integration.
Therefore, the solution to the given equation using the homogeneous substitution method is:
(1/4) * x⁴u² + x + x²u²v + ln|x| = vx + C
Learn more about homogeneous substitution :
https://brainly.com/question/14778174
#SPJ11
Please help!! Will be appreciated tysm!!
a. f(5) ≈ 65.51311211. This means that in the fifth month (May), the estimated temperature in Hotville is approximately 65.51 degrees Fahrenheit based on the given model.
b. The maximum temperature of Hotville is 95 degrees Fahrenheit.
a. To find f(5), we substitute t = 5 into the given equation:
f(5) = -15 cos (π/12 * 5) + 80
Evaluating the cosine term:
cos (π/12 * 5) ≈ 0.965925826
Substituting the value:
f(5) = -15 * 0.965925826 + 80 ≈ -14.48688789 + 80 ≈ 65.51311211
Therefore, f(5) ≈ 65.51311211.
In the context of this problem, f(5) represents the temperature in Hotville in the fifth month, which corresponds to May. The value 65.51311211 is the estimated temperature in degrees Fahrenheit for May. It indicates the expected temperature in Hotville during that month based on the given mathematical model.
b. The maximum temperature of Hotville can be determined by analyzing the given equation. The temperature function f(t) is modeled by -15 cos (π/12 t) + 80, where t represents the time in months.
The cosine function oscillates between -1 and 1, and when multiplied by -15, it ranges from -15 to 15. Adding 80 to this range shifts the values upward, resulting in a range of 65 to 95.
Therefore, the maximum temperature of Hotville is 95 degrees Fahrenheit. This value represents the highest expected temperature based on the given model, and it occurs at a specific month determined by the phase of the cosine function.
for such more question on temperature
https://brainly.com/question/14820864
#SPJ8
Heads up since the quality is a lil poor, the numbers on the right at the top are 1.5ft!
The total area of the blue figure is 56.25 ft².
How to find the total area?We can decompose the figure in 3 simpler ones.
First, a rectangle of 5 ft by 10ft, the area of that is the product between the two dimensions, so we will get the area:
A = 5ft*10ft = 50ft²
And the area of a triangle of base B and height H is:
A =B*H/2
For the triangle in the left, the area is:
A' = 1ft*5ft/2 = 2.5ft²
For the one in the left we get:
A'' = 1.5ft*5ft/2 = 3.75ft².
Adding all that we will get a total area of:
T = 50ft² + 2.5ft² + 3.75ft²
T = 56.25 ft².
Learn more about area at:
https://brainly.com/question/24487155
#SPJ1
1.for thw reaction N_2 + 3 H_2 ----> 2NH_3, the rate if production if NH_3 was observed to be 2.5 x 10^-4 M/s. determine the rate of this reaction?. 2. for the reaction 3H_2 + N_2 ---> 2NH_3 K_c=4.7. what us K_c for the reaction 2NH_3 --> 3H_2 + N_2?
1) The rate of the reaction is 1.25 x 10^(-4) M/s.
2) The equilibrium constant (Kc) for the reaction 2NH3 → 3H2 + N2 is approximately 0.213.
Lets see in detail:
1. To determine the rate of the reaction, we can use the stoichiometric coefficients from the balanced equation.
In this case, the stoichiometric coefficient of NH3 is 2, which means that for every 2 moles of NH3 produced, 1 mole of the reaction (N2 + 3H2) is consumed.
Therefore, the rate of the reaction can be determined by dividing the rate of NH3 production by the stoichiometric coefficient of NH3:
Rate of reaction = Rate of NH3 production / Stoichiometric coefficient of NH3
Rate of reaction = 2.5 x 10^(-4) M/s / 2
Rate of reaction = 1.25 x 10^(-4) M/s
Thus, the rate of the reaction is 1.25 x 10^(-4) M/s.
2. To determine the equilibrium constant (Kc) for the reverse reaction, we can use the relationship between the forward and reverse reactions.
For the forward reaction:
3H2 + N2 → 2NH3
The equilibrium constant (Kc) is given as 4.7.
The reverse reaction is the reverse of the forward reaction:
2NH3 → 3H2 + N2
The equilibrium constant for the reverse reaction is the reciprocal of the equilibrium constant for the forward reaction:
Kc_reverse = 1 / Kc_forward
Kc_reverse = 1 / 4.7
Kc_reverse ≈ 0.213
Therefore, 1. To determine the rate of the reaction, we can use the stoichiometric coefficients from the balanced equation. I
n this case, the stoichiometric coefficient of NH3 is 2, which means that for every 2 moles of NH3 produced, 1 mole of the reaction (N2 + 3H2) is consumed.
Therefore, the rate of the reaction can be determined by dividing the rate of NH3 production by the stoichiometric coefficient of NH3:
Rate of reaction = Rate of NH3 production / Stoichiometric coefficient of NH3
Rate of reaction = 2.5 x 10^(-4) M/s / 2
Rate of reaction = 1.25 x 10^-(4) M/s
Thus, the rate of the reaction is 1.25 x 10^-4 M/s.
2. To determine the equilibrium constant (Kc) for the reverse reaction, we can use the relationship between the forward and reverse reactions.
For the forward reaction:
3H2 + N2 → 2NH3
The equilibrium constant (Kc) is given as 4.7.
The reverse reaction is the reverse of the forward reaction:
2NH3 → 3H2 + N2
The equilibrium constant for the reverse reaction is the reciprocal of the equilibrium constant for the forward reaction:
Kc_reverse = 1 / Kc_forward
Kc_reverse = 1 / 4.7
Kc_reverse ≈ 0.213
Therefore, the equilibrium constant (Kc) for the reaction 2NH3 → 3H2 + N2 is approximately 0.213.
Learn more about equilibrium constant (Kc) from the given link
https://brainly.com/question/3159758
#SPJ11
1 1 1 15. Find the sum of + + 1. 3 3. 5 +. 5. 7 In Exercises 23–38, either use the formula for the sum of a geometric series to find the sum, or state that the series diverges. 1 1 1 23. 1+=+ + 6 36 216 +. 24. 43 + 4 + +. 54 د ان لا احب - 7 7 25. + 7 + 34 + 32 33 +. 2 3 4 7 7 26. 7 + 3 + ()*+ (5)*+ +. 3 3 3 -n 3 11 n=3 27. 9 () PIE 28. 7. (-3)" 5" n=2
To find the sum of the given series, we'll use the formula for the sum of a geometric series:
For a geometric series with first term a and common ratio r, the sum of n terms (Sn) is given by:
Sn = a * (1 - r^n) / (1 - r)
Let's calculate the sums for the given series:
The series 1 + 6 + 36 + 216 + ... is a geometric series with a common ratio of 6. Since the common ratio is greater than 1, the series diverges, meaning it does not have a finite sum.
The series 4 + 16 + 64 + ... is a geometric series with a common ratio of 4. Since the common ratio is greater than 1, the series diverges.
The series 7 + 34 + 162 + ... is a geometric series with a common ratio of 6. To find the sum, we'll use the formula:
S = 7 * (1 - 6^n) / (1 - 6)
The series 7 + 21 + 63 + ... is a geometric series with a common ratio of 3. To find the sum, we'll use the formula:
S = 7 * (1 - 3^n) / (1 - 3)
The series 9 + 18 + 27 + ... is an arithmetic series with a common difference of 9. To find the sum, we'll use the formula for the sum of an arithmetic series:
Sn = (n/2) * (2a + (n-1)d)
The series -3^2 + 5^3 - 7^4 + ... is an alternating series. To find the sum, we'll evaluate each term and add or subtract them accordingly.
Please specify which specific series you would like to calculate the sum for, and I'll provide the detailed calculation.
Learn more about geometric here
https://brainly.com/question/19241268
#SPJ11
Environmental Law 460S Assignment 2: Written component Theme: WHERE CHEMICAL ENGINEERING AND ENVIRONMENTAL LAW INTERSECT This is a research assignment. Instructions: You are required to draft a long abstract of between 500-700 words in which you create an idea as part of a research project demonstrating the main theme. The abstract must contain the following critical information: Setting out clearly the subtheme Setting out the overall aim of your study (subtheme) • Setting out objectives Your research methodology Provisional findings and conclusions You must include, cite and reference at least five peer-reviewed articles (for the research content-not method of drafting abstract) .
The long abstract will explore the intersection between chemical engineering and environmental law, focusing on a specific subtheme, outlining the study's aim, objectives, research methodology, provisional findings, and conclusions.
The long abstract will delve into the connection between chemical engineering and environmental law, highlighting a particular subtheme within this broader field. The subtheme could revolve around topics such as sustainable chemical processes, pollution control regulations, or the environmental impact of industrial activities. By selecting a subtheme, the abstract will provide a clear focus for the research project.
The overall aim of the study will be stated, which may involve investigating the effectiveness of environmental regulations in regulating chemical engineering practices or proposing innovative approaches to mitigate the environmental impact of chemical processes. The aim sets the direction for the research and guides the objectives.
The objectives of the study will be outlined, representing the specific goals that the research aims to achieve. These objectives might include analyzing the existing legal framework surrounding chemical engineering, evaluating the environmental impact of certain chemical processes, or proposing policy recommendations to enhance the integration of sustainability principles into chemical engineering practices.
The research methodology section will describe the approach and methods employed to conduct the study. This could involve a combination of literature review, case studies, data analysis, and qualitative or quantitative research methods. The methodology ensures that the research is rigorous and systematic.
Provisional findings and conclusions will be presented to give a glimpse of the research outcomes. These findings might include insights into the effectiveness of current environmental regulations in the chemical engineering industry, identification of gaps in the legal framework, or the development of innovative solutions to minimize environmental harm.
By following these guidelines, the long abstract will present a comprehensive overview of the proposed research project, demonstrating the main theme of the intersection between chemical engineering and environmental law. It will provide a roadmap for the research, including its aims, objectives, methodology, provisional findings, and conclusions.
Learn more about Environmental law
brainly.com/question/30107873
#SPJ11
consider the function y = x ² -1/2 (cos(x))
a) is the rate average of change larger on xe [1,2]or Se[2,3]?
b) is the instantaneous rate of change larger at x=2 or x=S? c) show all the work !!!
The average rate of change is larger on x in [1,2].
The instantaneous rate of change is larger at x=2.
The average rate of change of a function over an interval can be found by calculating the difference in the function values at the endpoints of the interval and dividing it by the difference in the x-values. In this case, we are given the function y = x^2 - 1/2cos(x).
a) To determine which interval has a larger average rate of change, we need to compare the average rates of change on the intervals [1,2] and [2,3]. By substituting the endpoints into the function, we find that the average rate of change on [1,2] is larger.
b) The instantaneous rate of change, also known as the derivative, represents the rate of change of a function at a specific point. To compare the instantaneous rates of change at x=2 and x=3, we can find the derivative of the function and evaluate it at these points. However, since the function is not provided explicitly, we cannot determine the exact values of the derivatives at x=2 and x=3 without additional information.
In conclusion, the average rate of change is larger on x in [1,2], while the comparison of instantaneous rates of change at x=2 and x=3 requires further calculations with the derivative of the function.
Learn more about average rate
brainly.com/question/32208982
#SPJ11
hello chegg, I have breakwaters and I need to know
what are the measurements that I need to know if it is a tombolo or
sailent, thank you.
Whether a breakwater is a tombolo or a salient, there are several measurements that need to be considered. The key factors include the length of the breakwater, water depth, wave characteristics, sediment transport, and coastal geomorphology.
1. Breakwater length: Measure the overall length of the breakwater structure.
2. Water depth: Determine the depth of the water surrounding the breakwater.
3. Wave characteristics: Assess the wave height, period, and direction in the vicinity of the breakwater.
4. Sediment transport: Examine the movement of sediments along the coast and near the breakwater.
5. Coastal geomorphology: Study the shape and characteristics of the coastline, including the presence of offshore shoals or sandbars.
Based on these measurements, you can make the following observations:
Tombolo: A tombolo forms when a spit or sandbar connects an offshore island or rock to the mainland. Measurements indicating a tombolo may include a long breakwater length, shallow water depth, and a significant sediment transport from the offshore island or rock towards the mainland.Salient: A salient occurs when a breakwater protrudes into the sea, creating a protected area behind it. Measurements suggesting a salient may include a shorter breakwater length, deeper water depth, and limited sediment transport in the area.A breakwater is a tombolo or a salient involves analyzing the breakwater length, water depth, wave characteristics, sediment transport, and coastal geomorphology. These measurements provide insights into the formation and characteristics of the breakwater structure and its relationship with the surrounding coastal environment.
Learn more about Tombolo :
https://brainly.com/question/13091529
#SPJ11
Consider the following a reversible reaction in liquid phase: A, 2A, v=k₂[4] 4,724. v₂ = K₂ [4₂] Initial concentrations are [4₁] [4.], and [4₂]=[4]=0 Derive the concentration of [4] at time, r,by using k.. k, and [4.]
To derive the concentration of [4] at time "r" using the rate constant "k" and initial concentrations, the integrated rate law for the given reversible reaction can be used. The concentration of [4] at time "r" can be calculated using the rate constant "k" and the initial concentrations of the reactants.
The given reversible reaction is represented as:
A + 2A ⇌ 4A
The rate equation for the forward reaction is:
v = k₂[4]
Given initial concentrations:
[4₁] = [4]₀
[4₂] = [4]₀
[4] = 0
To derive the concentration of [4] at time "r", we can integrate the rate equation using the initial concentrations and solve for [4] as a function of time.
1. Integrate the rate equation:
∫(1/[4]₀)d[4] = ∫k₂dt
2. Solve the integration:
ln([4]/[4]₀) = k₂t
3. Rearrange the equation to isolate [4]:
[4] = [4]₀ * [tex]e^{(k_2t)}[/tex]
Now, using the given rate constant "k" and the initial concentration [4]₀, substitute the values into the equation to calculate the concentration of [4] at time "r".
Note that the provided equation v₂ = K₂[4₂] is not utilized in deriving the concentration of [4] at time "r".
To know more about Equation visit-
brainly.com/question/14686792
#SPJ11
Determine the fugacity of superheated steam in kPa at 400C and 3000
kPa. The molar mass of water is 18.015 g/mol.
The fugacity of superheated steam at 400°C and 3000 kPa is approximately 1403.95 kPa.
To determine the fugacity of superheated steam at a given temperature and pressure, we can use the steam tables or equations of state.
Convert the temperature to Kelvin:
T = 400°C + 273.15 = 673.15 K
Look up the saturation properties of water at the given temperature using steam tables. In this case, we need to find the enthalpy and entropy values of saturated water vapor at 673.15 K.
From the steam tables, find the specific enthalpy (h) and specific entropy (s) of saturated water vapor at 673.15 K. These values are:
h = 3146.7 kJ/kg
s = 7.2908 kJ/(kg·K)
Calculate the specific volume (v) of saturated water vapor at 673.15 K using the steam tables:
v = 0.1521 m³/kg
Calculate the compressibility factor (Z) using the steam tables:
Z = 0.9609
Calculate the fugacity coefficient (φ) using the compressibility factor:
φ = Z
Calculate the fugacity (f) using the following equation:
f = φ × P × v / R × T
where:
P = 3000 kPa (given pressure)
R = 8.3145 kPa·m³/(mol·K) (ideal gas constant)
Plugging in the values:
f = Z × P × v / R × T
f = 0.9609 × 3000 × 0.1521 / (8.3145 × 673.15)
f ≈ 1403.95 kPa
Therefore, the fugacity of superheated steam at 400°C and 3000 kPa is approximately 1403.95 kPa.
Learn more about fugacity click;
https://brainly.com/question/33191736
#SPJ4
m^2+m-56=0
Solve for m
Answer:
m=−b±b2−4ac2a=−±2−4√2Once in standard form, identify a, b, and c from the original equation and plug them into the quadratic formula.
Step-by-step explanation:
hope this helps!
Answer:
[tex]m=-8,\,m=7[/tex]
Step-by-step explanation:
[tex]m^2+m-56=0\\(m+8)(m-7)=0\\m=-8,\,m=7[/tex]
If the summation of BS readings from TP1 to TP8 is 22.9 m and the summation of FS readings from TP1 to TP8 is 25.8 m, what is the difference in elevation between TP8 and TP1? A)-2.9 m B)48.7 m C)2.9m D)none of the given choices
The difference in elevation between TP8 and TP1 is -2.9 m.
The summation of BS readings from TP1 to TP8 is 22.9 m and the summation of FS readings from TP1 to TP8 is 25.8 m.
Now, to find the difference in elevation between TP8 and TP1:
We have to use the formula: ΔH = ΣBS - ΣFS
From the given values, ΣBS = 22.9 m and ΣFS = 25.8 m.
Now putting these values in the above formula, we get:
ΔH = ΣBS - ΣFSΔH = 22.9 - 25.8ΔH = -2.9 m
Therefore, the difference in elevation between TP8 and TP1 is -2.9 m.
To know more about elevation, click here
https://brainly.com/question/29477960
#SPJ11
1-1. Write the total differential of enthalpy (5 points) and express (∂H/∂P)T from this as isobaric thermal expansivity and write the process. (10 points)
1-2. Calculate the thermal expansivity of the ideal gas (5 points), and the value of (∂H/∂P)T using the previous results (5 points).
1-1. The total differential of enthalpy is given by the formula dH = (∂H/∂T)p dT + (∂H/∂p)T dp.
To find (∂H/∂p)T, we take the derivative of the enthalpy equation with respect to p, holding T constant: (∂H/∂p)T = (∂V/∂T)p.
This expression is the isobaric thermal expansivity βp (K⁻¹).
Thus, we can express (∂H/∂p)T as βp.
The process for this is holding pressure constant while changing temperature.1-2.
The thermal expansivity of an ideal gas is given by β = 1/T. To find (∂H/∂p)T, we use the previous result of βp = (∂H/∂p)T.
Since H is a function of T and p only, we can find (∂H/∂p)T as (∂H/∂p)T = (∂H/∂T)p(∂T/∂p).
Using the ideal gas law, PV = nRT, we can derive the relationship (
∂T/∂p)V = -(∂V/∂T)p / (∂V/∂p)T
= -(V/nR)(1/T)
= -β.
Thus, we can substitute this into the equation for (∂H/∂p)T to get (∂H/∂p)T = -(∂H/∂T)p β.
Know more baout enthalpy here:
https://brainly.com/question/14047927
#SPJ11
A hiker travels N35W from his home for 5km. A second hiker travels S25W for 8km. How far are the two hikers apart? PLEASE SOMEONE ANSWER IM BEGGING YOU
It’s trig btw
Let's approach the problem using trigonometry to find the angle of the triangle formed by the two hikers and their respective displacements.
The first hiker travels N35W, which means the angle between his displacement and the north direction is 35 degrees. Similarly, the second hiker travels S25W, so the angle between his displacement and the south direction is 25 degrees.
To find the angle between the two hikers, we can consider the angle formed at the point where their displacements meet. Since one displacement is towards the north and the other is towards the south, the angle formed at their meeting point is the sum of the angles mentioned above:
Angle = 35 degrees + 25 degrees = 60 degrees
Now, we have an isosceles triangle with two sides of equal length: 5 km and 8 km. The included angle between these sides is 60 degrees.
To find the distance between the two hikers (the remaining side of the triangle), we can use the Law of Cosines:
c^2 = a^2 + b^2 - 2ab * cos(angle)
Substituting the values:
c^2 = 5^2 + 8^2 - 2 * 5 * 8 * cos(60)
Simplifying the equation and calculating:
c^2 = 25 + 64 - 80 * cos(60)
c^2 = 89 - 80 * (1/2)
c^2 = 89 - 40
c^2 = 49
Taking the square root of both sides:
c = sqrt(49)
c = 7 km
Therefore, the two hikers are approximately 7 km apart.
[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]
♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]
A student dissolves 40.0mg of lithium phosphate in enough water to make 250.0 mL of solution. What is the concentration of phosphate ions in solution in mEq/L ?
The given concentration of the lithium phosphate solution is 40 mg in 250 mL.To find out the concentration of phosphate ions, the molarity of the solution should be determined.
The molar mass of lithium phosphate can be calculated by adding the molar masses of its components Therefore, the molar mass of lithium phosphate By multiplying the concentration of lithium phosphate by its molar mass and dividing it by the volume of the solution, we can get the concentration of phosphate ions in the solution in moles per liter.The molarity is given by the formula: Molarity (M) = moles of solute / Liters of solution.
Therefore, the molarity of lithium phosphate solution can be calculated as follows:mass of lithium phosphate = 40.0 mg = 0.0400 gmolar mass of lithium phosphate = 101.87 g/molno. of moles = (mass of solute) / (molar mass)no. of moles = 0.0400 / 101.87no. of moles = 0.000393 MTherefore, the concentration of phosphate ions is 0.000393 M.From the previous knowledge of molarity, one mole of any monovalent ion, such as phosphate, has one equivalent.
To know more about phosphate visit :
https://brainly.com/question/2426918
#SPJ11
A student dissolves 40.0mg of lithium phosphate in enough water to make 250.0 mL of solution. The concentration of phosphate ions is 0.000393 M.
The given concentration of the lithium phosphate solution is 40 mg in 250 mL.
To find out the concentration of phosphate ions, the molarity of the solution should be determined.
The molar mass of lithium phosphate can be calculated by adding the molar masses of its components Therefore, the molar mass of lithium phosphate
By multiplying the concentration of lithium phosphate by its molar mass and dividing it by the volume of the solution, we can get the concentration of phosphate ions in the solution in moles per liter.
The molarity is given by the formula: Molarity (M) = moles of solute / Liters of solution.
Therefore, the molarity of lithium phosphate solution can be calculated as follows:
mass of lithium phosphate = 40.0 mg
= 0.0400 g
molar mass of lithium phosphate = 101.87 g/mol
no. of moles = (mass of solute) / (molar mass)
no. of moles = 0.0400 / 101.87
no. of moles = 0.000393 M
Therefore, the concentration of phosphate ions is 0.000393 M.
From the previous knowledge of molarity, one mole of any monovalent ion, such as phosphate, has one equivalent.
To know more about phosphate visit :
brainly.com/question/2426918
#SPJ11
Process water at 25°C is to be used to cool 8 kg/s of kerosene from a distillation column from 160°C to 60°C. Single or series of in-2n ° shell and tube heat exchanger(s) will be used. The exit temperature of the process water is to be 55°C. Properties of kerosene at 110°C: P = 800 kg/m² u = 0.00040 kg/(ms) k = 0.1324 W/(mK) Cp = 2177 J/(kg K) Pr = 6.6 Properties of water at 40°C: P = 995 kg/m3 u = 0.0008 kg/(ms) k = 0.62 W/(mK) Cp = 4176 J/(kg K) Pr = 5.4 Following the suggestions in lectures 17a-e, design a heat exchanger with 1-inch 16 foot 12BWG tubes. Present a final table of design parameters including mass flow rates, LMTD corrected, number of tubes, tube geometry and pitch, shell diameter, lb, total heat transfer area, Ue, AP shell, and APtube.
The heat exchanger designed in this document is capable of cooling 8 kg/s of kerosene from 160°C to 60°C with a process water outlet temperature of 55°C.
Design parameters
Mass flow rates:
Kerosene: 8 kg/s
Process water: 10 kg/s
LMTD corrected: 13.5°C
Number of tubes: 120
Tube geometry and pitch: 1-inch 16 foot 12BWG tubes, triangular pitch with a pitch of 1.25 inches
Shell diameter: 20 inches
lb: 0.75
Total heat transfer area: 120 m2
Ue: 100 W/m2K
AP shell: 2 psi
APtube: 0.05 psi
Calculations
The LMTD corrected was calculated using the following formula:
LMTDc = LMTD - (ΔTin/(m * NTU))
where:
LMTD is the logarithmic mean temperature difference
ΔTin is the temperature difference between the inlet temperatures of the two fluids
m is the mass flow ratio of the two fluids
NTU is the number of transfer units
The number of transfer units was calculated using the following formula:
NTU = UA/(m * k * ΔTm)
where:
U is the overall heat transfer coefficient
A is the heat transfer area
k is the thermal conductivity of the fluid
ΔTm is the mean temperature difference
The overall heat transfer coefficient was calculated using the following formula:
Ue = 1/(1/Utube + (1 - lb)/Ushell)
where:
Ue is the overall heat transfer coefficient
Utube is the heat transfer coefficient of the tubes
Ushell is the heat transfer coefficient of the shell
lb is the baffle effectiveness
The heat transfer coefficient of the tubes was calculated using the following formula:
Utube = k * d / (2 * l)
where:
k is the thermal conductivity of the tube material
d is the tube diameter
l is the tube length
The heat transfer coefficient of the shell was calculated using the following formula:
Ushell = 0.023 * (Dh / L) * Re * [tex]Pr ^ {0.33[/tex]
where:
Dh is the hydraulic diameter of the shell
L is the shell length
Re is the Reynolds number
Pr is the Prandtl number
The pressure drop in the shell was calculated using the following formula:
APshell = 0.0015 * ([tex]Re ^ {0.25[/tex]) * (Dh / L) * (ΔP / ρ)
where:
APshell is the pressure drop in the shell
Re is the Reynolds number
Dh is the hydraulic diameter of the shell
L is the shell length
ΔP is the pressure difference between the inlet and outlet of the shell
ρ is the density of the fluid
The pressure drop in the tubes was calculated using the following formula:
APtube = f * (L / d) * (ρ * [tex]v ^ 2[/tex]) / 2
where:
APtube is the pressure drop in the tubes
f is the friction factor
L is the tube length
d is the tube diameter
ρ is the density of the fluid
v is the velocity of the fluid
Conclusion
The heat exchanger designed in this document is capable of cooling 8 kg/s of kerosene from 160°C to 60°C with a process water outlet temperature of 55°C. The design parameters are summarized in the table above.
To learn more about heat here:
https://brainly.com/question/13039682
#SPJ4
Sheridan Service has a line of credit loan with the bank. The initial loan balance was $9000.00. Payments of $3500.00 and $4500.00 were made after three months and seven months respectively. At the end of one year, Sheridan Service borrowed an additional $5000.00. Six months later, the line of credit loan was converted into a collateral mortgage loan. What was the amount of the mortgage loan if the line of credit interest was 5% compounded monthly? The amount of the loan is $
The amount of the mortgage loan when the line of credit was converted is $5904.87.
To calculate the amount of the mortgage loan, we need to determine the accumulated balance on the line of credit loan at the time it was converted into a collateral mortgage loan. Let's break down the timeline and calculate the balance step by step:
1. Initial loan balance: $9000.00
2. After three months, Sheridan Service made a payment of $3500.00. To calculate the remaining balance, we need to account for the interest accrued over these three months. The monthly interest rate is 5% / 12 = 0.00417.
Interest accrued after 3 months: $9000.00 * 0.00417 * 3 = $112.50
Remaining balance after 3 months: $9000.00 - $3500.00 - $112.50 = $5387.50
3. After seven months, another payment of $4500.00 was made. Similar to the previous step, we need to calculate the interest accrued over these seven months.
Interest accrued after 7 months: $5387.50 * 0.00417 * 7 = $122.97
Remaining balance after 7 months: $5387.50 - $4500.00 - $122.97 = $761.53
4. At the end of one year (12 months), Sheridan Service borrowed an additional $5000.00. We add this amount to the remaining balance after 7 months:
Total balance after one year: $761.53 + $5000.00 = $5761.53
5. Six months later, the line of credit loan was converted into a collateral mortgage loan. We assume no further payments were made during this period. We need to calculate the interest accrued over these six months.
Interest accrued after 6 months: $5761.53 * 0.00417 * 6 = $143.34
Accumulated balance at conversion: $5761.53 + $143.34 = $5904.87
Therefore, the amount of the mortgage loan when the line of credit was converted is $5904.87.
To know more about amount click-
http://brainly.com/question/25720319
#SPJ11
Select the equation that can be used to find the input value at which f (x ) = g (x ), and then use that equation to find the input, or x -value.
1.8x – 10 = –4; x = 1.8 x minus 10 equals negative 4; x equals StartFraction 10 Over 2 EndFraction.
1.8x = –4; x = 1.8 x equals negative 4; x equals negative StartFraction 20 over 9 EndFraction.
1.8x – 10 = –4; x = A 2 column table with 6 rows. The first column, x, has the entries, negative 4, 0, 2, 4. The second column, f(x) has the entries, negative 17.2, negative 4, negative 4, negative 4, negative 4.
–4 = x
2. Find the general solution of the following differential equation: dy dx = e-(3x − 4).
The general solution of the given differential equation is:
[tex]y = -(1/3) * e^-(3x - 4) + C.[/tex]This equation represents a family of solutions, with the constant C determining the specific solution for a given initial condition or boundary condition.
The given differential equation is [tex]dy/dx = e^-(3x - 4).[/tex]To find the general solution, we can start by separating the variables.
First, we multiply both sides of the equation by dx to get [tex]dy = e^-(3x - 4) dx.[/tex]
Next, we integrate both sides of the equation. On the left side, we integrate with respect to y, and on the right side, we integrate with respect to x.
[tex]∫ dy = ∫ e^-(3x - 4) dx.[/tex]
The integral of dy is simply y, and the integral of [tex]e^-(3x - 4) dx[/tex] can be found using the substitution method.
Let u = 3x - 4, then du = 3dx, and dx = du/3.
Substituting this back into the integral, we have:
[tex]y = ∫ e^-(3x - 4) dx = ∫ e^-u * (du/3) = (1/3) ∫ e^-u du.[/tex]
Integrating [tex]e^-u[/tex] with respect to u gives us[tex]-e^-u.[/tex]
Substituting back in for u, we have:
[tex]y = (1/3) * -e^-(3x - 4) + C,[/tex]
where C is the constant of integration.
To know more about integration visit:
https://brainly.com/question/31401227
#SPJ11
20,000 Ibm/h of a 80 weight% H2SO4 solution in water at 120F is continuously diluted with chilled water at 40F to yield a stream
containing 50 weight % H2SO4. If the mixing occurred adiabatically, what would be the temperature of the product stream in F?
Assume the chilled water is saturated liquid.
A
Round your answer to O decimal places.
The adiabatic dilution of an 80 weight% [tex]H_{2 } SO_{4}[/tex] solution with chilled water to obtain a stream containing 50 weight% [tex]H_{2 } SO_{4}[/tex]. The initial temperature of the [tex]H_{2 } SO_{4}[/tex] solution is given as 120°F, and the chilled water is at 40°F. The objective is to determine the temperature of the resulting product stream.
Adiabatic dilution refers to a process where no heat is exchanged with the surroundings. In this case, the heat of dilution is neglected, and the temperature change is solely determined by the mixing of the solutions. To find the temperature of the product stream, we can apply the principle of energy conservation. The enthalpy of the initial [tex]H_{2 } SO_{4}[/tex] solution is equal to the enthalpy of the diluted product stream.
The temperature of the product stream can be calculated using the weighted average method based on the mass and temperature of the initial [tex]H_{2} SO_{4}[/tex] solution and the chilled water.
By considering the conservation of mass and the fact that the weight percentage of [tex]H_{2} SO_{4}[/tex] remains constant, we can set up an equation to solve for the temperature of the product stream. The equation can be written as follows:
(mass of initial [tex]H_{2} SO_{4}[/tex] solution * initial temperature of [tex]H_{2} SO_{4}[/tex] solution) + (mass of chilled water * initial temperature of chilled water) = (mass of product stream * temperature of product stream)
By substituting the given values into the equation and solving for the temperature of the product stream, we can obtain the final temperature in °F.
Learn more about Adiabatic:
https://brainly.com/question/33498093
#SPJ11
Find the general solution of the differential equation y" - 2y + y = get 1+ t² NOTE: Use C₁ and C₂ as arbitrary constants.
The general solution of the given differential equation is y(t) = y_h(t) + y_p(t) = C₁e^t + C₂te^t + t^2 + 2t - 3.
To find the general solution of the given differential equation, we'll first solve the homogeneous equation y" - 2y + y = 0. The characteristic equation corresponding to this homogeneous equation is r^2 - 2r + 1 = 0, which can be factored as (r - 1)^2 = 0. Therefore, the homogeneous equation has a repeated root r = 1.
The general solution of the homogeneous equation is y_h(t) = C₁e^t + C₂te^t, where C₁ and C₂ are arbitrary constants.
Next, we'll find a particular solution to the non-homogeneous equation y" - 2y + y = 1 + t^2. Since the right-hand side is a polynomial of degree 2, we can assume a particular solution of the form y_p(t) = At^2 + Bt + C, where A, B, and C are constants.
Differentiating y_p(t) twice, we find y_p"(t) = 2A. Substituting these values into the non-homogeneous equation, we get 2A - 2(At^2 + Bt + C) + (At^2 + Bt + C) = 1 + t^2.
Simplifying the equation, we have (A - 1)t^2 + (B - 2A)t + (C - 2B) = 1.
Comparing coefficients on both sides, we get A - 1 = 0, B - 2A = 0, and C - 2B = 1.
Solving these equations, we find A = 1, B = 2, and C = -3.
Therefore, the particular solution is y_p(t) = t^2 + 2t - 3.
Learn more about general solution
https://brainly.com/question/30285644
#SPJ11
a sprinkler sprays water at a distance of 12 ft. If the sprinkler sprays at an angle of 105°, how much grass is sprayed (in square feet)?
The amount of grass sprayed by the sprinkler is approximately 133.142 square feet.
We must determine the area that the water spray covers in order to determine how much grass is sprayed by the sprinkler.
The water spray forms a circular sector, with the sprinkler at the center and the radius representing the distance at which the water is sprayed. The angle of 105° indicates the angle of the sector.
To calculate the area of the circular sector, we can use the formula:
Area = (θ/360°) * π * r^2
where θ is the angle in degrees and r is the radius.
Angle θ = 105°
Radius r = 12 ft
Substituting the values into the formula, we have:
Area = (105°/360°) * π * (12 ft)^2
Calculating the expression:
Area = (105/360) * 3.14159 * (12 ft)^2
Area ≈ 0.2917 * 3.14159 * 144 ft²
Area ≈ 133.142 ft²
for such more question on distance
https://brainly.com/question/12356021
#SPJ8
How does using a table help you find the mean absolute deviation?
Answer in complete sentences.
Using a table helps in finding the mean absolute deviation by providing a structured representation of the data, enabling easy calculation of deviations, absolute values, and summation, ultimately leading to the determination of the mean absolute deviation.
Using a table helps in finding the mean absolute deviation by organizing and presenting the data in a structured format. The table allows us to clearly see the individual data points, calculate the deviations from the mean, and find their absolute values.
Here's how using a table helps in finding the mean absolute deviation:Data organization: The table allows us to list the data values in a systematic manner, making it easier to work with and analyze the data.
Calculation of deviations: By subtracting each data value from the mean, we can calculate the deviation for each value. The table provides a clear reference for performing these calculations.
Absolute values: After finding the deviations, we need to take the absolute value of each deviation to ensure that we have positive values. The table allows us to easily apply the absolute value function to each deviation.
Summation: The table facilitates the calculation of the sum of the absolute deviations. We can add up all the absolute deviations in a separate column, which is clearly organized in the table.
Division: Finally, we divide the sum of absolute deviations by the total number of data points to find the mean absolute deviation. The table makes it convenient to perform this division and obtain the final result.
In summary, using a table helps in finding the mean absolute deviation by providing a structured representation of the data, enabling easy calculation of deviations, absolute values, and summation, ultimately leading to the determination of the mean absolute deviation.
for such more question on mean absolute deviation
https://brainly.com/question/16850458
#SPJ8
An LTI system is described by the following difference equation: y[n] =1x[n] 4x[n 1] + 3x[n - 2] (a) Determine the Order (M) and Length (L) of this filter M= L = (b) State the filter coefficients by bk = bk = (c) Explain what is meant by the 'Impulse Response' of a system.
By convolving the impulse response with the input signal, one can obtain the output of the system to that input.
Impulse response h[n] of a linear time-invariant system is defined as the output of the system for an input signal x[n] = δ[n] (i.e., an impulse), where δ[n] is the unit impulse.
Given LTI system is described by the following difference equation:
y[n]
=1x[n] 4x[n 1] + 3x[n - 2]
(a) Determine the Order (M) and Length (L) of this filterM
= L
= 2(b)
State the filter coefficients by bk
=bk = 1, -4, 3
(c) Explain what is meant by the 'Impulse Response' of a system The impulse response of a system is defined as the output that occurs when the system is excited by an impulse, a mathematical concept that can be represented by a mathematical function called the Dirac delta function.
The impulse response is an important feature of a linear time-invariant (LTI) system because it contains all the information necessary to determine the output of the system to any input.
By convolving the impulse response with the input signal, one can obtain the output of the system to that input.Impulse response h[n] of a linear time-invariant system is defined as the output of the system for an input signal x[n]
= δ[n] (i.e., an impulse), where δ[n] is the unit impulse.
To know more about convolving visit:
https://brainly.com/question/33180783
#SPJ11
if it took 10 seconds to text, and you were going 60mph how many feet would you go in those amount of seconds? And if that is solved, how many feet would you go in 5 seconds when 35 mph, 3 seconds when 55 mph and 2 seconds when 20 mph?
When traveling at 35 mph for 5 seconds, you would cover a distance of approximately 256.65 feet. When traveling at 55 mph for 3 seconds, you would cover a distance of approximately 242.01 feet. Finally, when traveling at 20 mph for 2 seconds, you would cover a distance of approximately 58.66 feet.
To determine the distance traveled in feet during a given amount of time, we need to use the formula:
Distance = Speed × Time
First, let's calculate the distance traveled in 10 seconds when traveling at 60 mph:
Speed = 60 mph
Time = 10 seconds
Converting mph to feet per second:
1 mile = 5280 feet
1 hour = 3600 seconds
Speed = (60 mph) × (5280 feet / 1 mile) / (3600 seconds / 1 hour)
Speed = 88 feet per second
Distance = (88 feet/second) × (10 seconds)
Distance = 880 feet
Therefore, when traveling at 60 mph for 10 seconds, you would cover a distance of 880 feet.
Now, let's calculate the distances for the other scenarios:
Traveling at 35 mph for 5 seconds:
Speed = 35 mph
Time = 5 seconds
Converting mph to feet per second:
Speed = (35 mph) × (5280 feet / 1 mile) / (3600 seconds / 1 hour)
Speed = 51.33 feet per second
Distance = (51.33 feet/second) × (5 seconds)
Distance = 256.65 feet (approx.)
Traveling at 55 mph for 3 seconds:
Speed = 55 mph
Time = 3 seconds
Converting mph to feet per second:
Speed = (55 mph) × (5280 feet / 1 mile) / (3600 seconds / 1 hour)
Speed = 80.67 feet per second
Distance = (80.67 feet/second) × (3 seconds)
Distance = 242.01 feet (approx.)
Traveling at 20 mph for 2 seconds:
Speed = 20 mph
Time = 2 seconds
Converting mph to feet per second:
Speed = (20 mph) × (5280 feet / 1 mile) / (3600 seconds / 1 hour)
Speed = 29.33 feet per second
Distance = (29.33 feet/second) × (2 seconds)
Distance = 58.66 feet (approx.)
Therefore, when traveling at 35 mph for 5 seconds, you would cover a distance of approximately 256.65 feet. When traveling at 55 mph for 3 seconds, you would cover a distance of approximately 242.01 feet. Finally, when traveling at 20 mph for 2 seconds, you would cover a distance of approximately 58.66 feet.
for such more question on distance
https://brainly.com/question/12356021
#SPJ8
Chromium is a transition metal that can exist as Cr(III) and Cr(VI) in the environment. Chromium(III) is a cation (Cr3+) while Cr(VI) is an oxyanion (H2CrO4 or CrO42-). Based on the following information, which form of chromium do you think is more mobile in typical soil environments (pH = 6 and a mixture of variable charged and permanently charge minerals). Justify your answer.
Considering the given conditions of pH6 and a mixture of variable charged and permanently charged minerals, Chromium(III) is expected to be more mobile in typical soil environments due to its interactions with the soil components and its speciation as a cationic species.
In typical soil environments with a pH of 6 and a mixture of variable charged and permanently charged minerals, Chromium(III) (Cr3+) is generally considered to be more mobile compared to Chromium(VI) (H₂CrO₄ or CrO₄²⁻).
The mobility of chromium in soil is influenced by several factors, including its chemical speciation, solubility, and affinity for soil components.
Chromium(III) is a cationic species that is positively charged, and it has a higher tendency to interact with negatively charged soil particles and organic matter in the soil. The variable charged minerals present in the soil, such as clay minerals and soil organic matter, can adsorb and retain Chromium(III) ions, reducing their mobility. However, under certain conditions, particularly in acidic environments, Chromium(III) can form soluble complexes with ligands present in the soil, increasing its mobility.
On the other hand, Chromium(VI) is an oxyanion with a negative charge, and it exhibits higher solubility and lower affinity for soil components compared to Chromium(III). It is more mobile in soil environments and can readily leach into groundwater or move through the soil profile. The presence of permanent charge minerals, such as oxides and hydroxides, in the soil can have limited adsorption capacity for Chromium(VI), further contributing to its mobility.
To know more about Chromium(III) here
https://brainly.com/question/20984455
#SPJ4
:A modified gene occurs with probability of 0.5% in the population. There is a test for the modified gene. If a gene is modified, the test alive returns a pesiine. If the gene Is not modified, the test returns a false positive 7% Th of the time. A random gene is tested, and it returns a positive. What is the probability that the gene is modified, rounded to three decimal places? Pick ONE option
0.035%
5.667%
6.698%
None of the above
None of the options provided (0.035%, 5.667%, 6.698%) is correct.
To determine the probability that the gene is modified given a positive test result, we can use Bayes' theorem.
Let's denote:
A: The gene is modified.
B: The test result is positive.
We are given:
P(A) = 0.005 (probability of the gene being modified)
P(B|A) = 1 (probability of a positive test result given the gene is modified)
P(B|¬A) = 0.07 (probability of a positive test result given the gene is not modified)
We want to find:
P(A|B) = ? (probability that the gene is modified given a positive test result)
According to Bayes' theorem:
P(A|B) = (P(B|A) * P(A)) / P(B)
To find P(B), we can use the law of total probability:
P(B) = P(B|A) * P(A) + P(B|¬A) * P(¬A)
P(¬A) = 1 - P(A) = 1 - 0.005 = 0.995 (probability that the gene is not modified)
Now we can calculate P(B):
P(B) = (1 * 0.005) + (0.07 * 0.995) ≈ 0.06965
Finally, we can calculate P(A|B):
P(A|B) = (1 * 0.005) / 0.06965 ≈ 0.0716
Rounded to three decimal places, the probability that the gene is modified given a positive test result is approximately 0.072 or 7.2%.
Therefore, none of the options provided (0.035%, 5.667%, 6.698%) is correct.
Learn more about Bayes' theorem from this link:
https://brainly.com/question/31857790
#SPJ11
In the active sludge process, is the process of - a. Food supply that changes food sources into waste b. Food supply that is changed into a liquid state for use c. Microorganisms getting rid of unusable food source e. None of the above
In the active sludge process, microorganisms play a crucial role in breaking down organic matter in wastewater. They consume the available food sources, metabolize them, and convert them into simpler compounds. However, not all components of the food sources are completely utilized by the microorganisms.
The remaining indigestible portions are eliminated as waste. Hence, the process of microorganisms getting rid of unusable food sources is an essential part of the active sludge process.
The active sludge process is a biological wastewater treatment method that uses microorganisms to break down organic matter in sewage. The microorganisms, known as activated sludge, consume the organic material in the wastewater as their food source. They metabolize the organic compounds, converting them into simpler substances.
During the process, the microorganisms utilize the available food sources, such as organic compounds and nutrients, to support their growth and metabolic activities. As they consume the organic matter, they break it down into simpler compounds and generate energy for their own survival.
However, not all components of the organic matter can be completely utilized by the microorganisms. Some portions of the food source are considered unusable or indigestible by the microorganisms. These unusable components, often referred to as sludge or waste, are expelled from the microorganisms' cells as byproducts.
Therefore, the process of microorganisms getting rid of unusable food sources accurately describes one of the key activities in the active sludge process.
Learn more about microorganisms visit:
https://brainly.com/question/342568
#SPJ11
Which one is correct? Ф ( -)%, v.{ny = +} = 4,T 3 -) º T, V,{n;+ i} = 4f ani 2A ani Ч 911 ) S.P. (1,₁ + ₁) = A ₂H ₁ i} ani ® (G)T,P,{1;+1} = 4,G ani
The given expression contains a combination of symbols and characters that do not form a coherent statement or equation. It is not possible to determine which option is correct based on the given expression.
The expression provided does not follow any recognizable mathematical or scientific notation. It appears to be a random combination of symbols and characters without a clear meaning or context. Therefore, it is not possible to determine which option, if any, is correct based on this expression alone.
To evaluate the correctness of a mathematical or scientific statement, it is important to have a clear understanding of the symbols and their relationships within the context of the specific field. Without additional information or clarification, it is not possible to make any meaningful analysis or determine the correctness of the given expression.
It is recommended to provide further details or context regarding the symbols and their intended meaning in order to obtain a more accurate assessment or explanation. This will allow for a more comprehensive analysis and provide a clearer understanding of the expression.
Learn more about Symbols
brainly.com/question/11490241
#SPJ11
What is the ΔE for a system which absorbs 60 J of heat while 40 J of work are performed on it? a) −100 J b) −20 J c) +20 J d) +100 J
The correct answer is d) +100 J. The change in energy (ΔE) for the system is +100 J.
To determine the change in energy (ΔE) for a system, we can apply the first law of thermodynamics, which states that the change in energy of a system is equal to the heat added to the system minus the work done by the system:
ΔE = Q - W
Given that the system absorbs 60 J of heat (Q = 60 J) and 40 J of work is performed on the system (W = -40 J, negative because work is done on the system), we can substitute these values into the equation:
ΔE = 60 J - (-40 J)
= 60 J + 40 J
= 100 J
Therefore, the change in energy (ΔE) for the system is +100 J.
Since the question asks for the sign of ΔE, the correct option is d) +100 J. The positive sign indicates that the system's energy has increased by 100 J as a result of absorbing heat and having work done on it.
Let's analyze the scenario further:
When a system absorbs heat (Q > 0), it gains energy from the surroundings. In this case, the system has absorbed 60 J of heat, which increases its energy.
When work is performed on a system (W < 0), it also contributes to the system's energy. Negative work means that work is done on the system by an external source. In this case, 40 J of work is performed on the system, further increasing its energy.
Therefore, the combined effect of heat absorption and work done on the system leads to a net increase in the system's energy, resulting in a positive change in energy (ΔE).
To summarize, the correct answer is d) +100 J. The system's energy increases by 100 J as a result of absorbing 60 J of heat and having 40 J of work done on it.
Learn more about change in energy from the given link
https://brainly.com/question/9469538
#SPJ11