list the three major factors that the study of architecture includes.

Answers

Answer 1
I think it is

Sensitivity to design
skill in drawing techniques
and the knowledge of the latest construction materials
If I am correct

Related Questions

The ratio of boys to girls in the class was 2 to 3. If there were 18 girls in the class, how many students were in the class

Answers

37 students in the class
18 Girls and 19 Boys

the need of families and suitability for the local____ have contributed to the structural styles of homes

Answers

Answer:

environment

Explanation:

the environment has different resources

Employees are working within an excavation that is more than 4 foot deep and cannot safely exit the site. What is a hazard that needs to be addressed in this situation?
Select the best option.

Access/Egress


Oxygen Deficiency and Toxic Fumes


Water Accumulation

Answers

The answer is Access/egress because the victim can get oxygen from the top and water from the other workers.

A hazard that needs to be addressed in the given situation is Access/Egress. Option A is correct.

What is the significance of Access and Egress?

When handling a security or emergency scenario, access and egress points are crucial. It is crucial to have rapid access to and exit from the building in case of an emergency.

Planning entrance and egress locations should be done while creating evacuation routes. A safe escape that people can use in an emergency is called emergency egress. In an emergency circumstance like a fire, emergency access and escape are crucial.

In the given case, Employees are working within an excavation that is more than 4 foot deep and cannot safely exit the site, this is clearly deined that the Access/Egress is a hazard that must be dealt.

Therefore, option A is correct.

Learn more about the hazard, refer to:

https://brainly.com/question/16529562

#SPJ6

Technician A says that to remove the rod caps on an engine, start by positioning the number 3 piston at top dead center. Technician B says that to remove the rod caps on an engine, start by positioning the number 1 piston at bottom dead center. Who is correct

Answers

Answer:

B.

Explanation:

Removing the rod caps on an engine, start by positioning the number 1 piston at bottom dead center is the correct way to remove them.

define architecture and Civil engineering in brief ​

Answers

Explanation:

While architects are responsible for the design and planning of structures ranging from houses and factories to skyscrapers and museums, civil engineers oversee the entire design-to-completion process for buildings, roads, dams, bridges, water systems, and other major works.

lu
22. The word biodegradable on a label doesn't necessarily mean a product is environmentally safe.
A) O True
B) O False

Answers

That would be A( O True

Student A says hazardous waste can take the form of solid, liquid, or gas. Student B says hazardous waste can only take the form of a solid. Who is correct?



Group of answer choices

Both A and B

Neither A nor B

Student A

Student B

Answers

Answer:

Student A

Explanation:

hope this helps have a great day

what are the materials and tools used to build a headgear?​

Answers

Modern headframes are built out of steel, concrete or a combination of both. Timber headframes are no longer used in industrialized countries, but are still used in developing nations.

Pls give me a brainliest if this helped thx

Apollo 13 Describe how the flight controllers developed and used models. What kind of drawings might they have used to solve the problem

Answers

Answer:

In order to power the fuel cells that provided most of the electricity used during the flight, the Apollo spacecraft carried two tanks of liquid hydrogen and two tanks of liquid oxygen. ... The testing team decided to solve this problem by heating the tank overnight to force the liquid oxygen to burn off

A series RLC circuit consists of a 100 W resistor, a 0.15 H inductor, and a 30 µF capacitor. It is attached to a 120 V/60 Hz power line (the voltage 120V is the root mean square value). What are



a. The emf εrms


b. The phase angle ϕ


c. The average power loss

Answers

B……………………………………………..

(a) The root mean square value of current in the circuit is 1.14 A.

(b) The phase angle ϕ of the circuit is 17.7⁰.

(c) The average power loss in the circuit is 136.4 W.

Capacitive and inductive reactance of the RLC circuit

The capacitive and inductive reactance of the series RLC circuit is calculated as follows;

Xc = 1/ωC

[tex]X_c = \frac{1}{2\pi f C} = \frac{1}{2\pi (60)(30 \times 10^{-6})} = 88.42 \ ohms[/tex]

Xl = ωL

Xl = 2πfL

Xl = 2π(60)(0.15)

Xl = 56.55 ohms

Impedance of the circuit

The impedance of the circuit is calculated as follows;

[tex]Z = \sqrt{R^2 + (X_c - X_l)^2} \\\\Z = \sqrt{100^2 + (88.42 -56.55)^2} \\\\Z = 104.96 \ ohms[/tex]

Rms current of the circuit

[tex]I_{rms} Z = V_{rms}\\\\I_{rms} = \frac{V_{rms}}{Z} \\\\I_{rms}= \frac{120}{104.96} \\\\I_{rms}= 1.14 \ A[/tex]

Phase angle

The phase angle of the circuit is calcuated as follows;

[tex]tan \phi = \frac{X_c - X_l}{R} \\\\tan\phi = \frac{88.42 - 56.55}{100} \\\\tan\phi = 0.3187\\\\\phi = tan^{-1}(0.3187) \\\\\phi = 17.7 \ ^0[/tex]

Average power loss in the circuit

The average power loss in the circuit is calculated as follows;

[tex]P = I_{rms}^2 Z\\\\P = (1.14)^2 (104.96)\\\\P = 136.4 \ W[/tex]

Learn more about phase angle here: https://brainly.com/question/16222725

Solve the inequality. Then graph your solution.
-9v – 10 < 7y +6

Answers

16

if you add 9+10 you get 18 - 7+6

TEST ANSWER

PLS IGNORE

3. Which of these tools is typically not used by Automotive Technicians?
A. Oxyfuel Cutting Equipment
B. Diagnostic Computers
C. Defibrillator
D. Test Instruments

Answers

The answer is "Option c", and more explanation can be defined as follows:

Automotive and mechanical service technicians alter their vehicles using oil. Autonomous service technicians and mechanics often referred to as service technicians or services technology experts, inspection, repair, and maintenance of automobiles & commercial vehicles.It contains fundamental rectangles, wrenches, sockets, flips & pinions. Tool to measure torques: As a technician, you will always take things apart and reassemble them. These tools tighten the attachments so that pieces can be reassembled properly. It uses oxyfuel cutters, diagnostic computers, and test instruments.

Therefore, "Option C" is correct.

Learn more:

brainly.com/question/19958954

If a motor or transformer has a low-frequency hum, what can be done to reduce/ eliminate the noise?

Answers

no because has a power and it still with noise

2
Tech A says the Wengine consists of two VR cylinder banks in a
deeper V arrangement to each other. Tech B says rotary engines are
very powerful for their size, but they do not use conventional pistons
that slide back and forth inside a straight cylinder. Who is correct?
of

Answers

Answer:tech A

Explanation:

e) What are the major jobs of a nurse?

Answers

Answer:

the major jobs of a nurse are

1.to take care of patients

2.to give medicine to patients in time

3.to help doctors in operation time

Explain how metal is produced and turned into a product e.g. bed

Answers

Answer:

the metal is mined from mines and melted to make objects

LIST the differences between softwood and hardwood

Answers

Answer:

Hardwood is usually denser than softwood.

Softwood is cheaper than hardwood.

Hardwood has good fire resistance while softwood has poor fire resistance.

Softwood is lighter than hardwood.

TEST ANSWER

PLS IGNORE

A tensile load of 5 kN was loaded on a 25 cm circular metal rod of diameter 1 cm,
causing an extension to be 0.0227 cm. Determine the value of Young’s modulus, E,
of the metal.

Answers

Answer:

70 GPa my guyyyy

Explanation:

Ayuda porfavor......

Answers

Answer:

yayayyayaaayaaaayyayayayayaayaaayayayayayayya

Oh no this is a hard question

What is the equation for area

Answers

Answer:

l×b is the equation of area

Studies show that chlorofluorocarbons (CFCs) such as CFC-12, are contributing to the depletion of the
stratospheric ozone layer.
A) True
B) False

Answers

True .the chlorofluorocarbons also known as CFC’s also contribute on depleting the ozone layer

Answer:

true

Explanation:

True .the chlorofluorocarbons also known as CFC’s also contribute on depleting the ozone layer

Which event is an example of science helping engineering?
A. Knowledge of local geology helps in the design of a dam for a
reservoir.
B. A new type of telescope helps people learn new facts about
comets.
C. A new type of computer makes weather forecasts more accurate.
D. Satellite imaging allows people to map the extent of forest fires.

Answers

A, because the Geology is helping the engineers design a dam.

An event that is an example of science helping to engineer is  Knowledge of local geology helps in the design of a dam for a reservoir. Thus the correct option is A.

What is Science?

Science is the systematic, evidence-based scientific investigation and implementation of knowledge and perception of the natural and social world which provides information about various things to an individual.

Combining math and science to tackle issues usually defines the functions of engineering.  Engineers are the ones who translate advances in science into practical applications. 

The individual who studies Science is referred to as a Scientist whereas those studies about engineering are referred to as Engineers.

When the design of a dam for a reservoir is created Science helps engineering by providing information and knowledge about Local Geology to help them.

Therefore, option A is appropriate.

Learn more about Science, here:

https://brainly.com/question/20820104

#SPJ6

What is equation for surface area?

Answers

Answer:

Surface area is the sum of the areas of all faces (or surfaces) on a 3D shape. pls mark me branilest

Which of the following does the electrical technician typically use?​

Answers

Answer:

What are the choices?

5. If you use pipe in a footing drain, there should be surface clean-out(s) located
O A. right next to the house.
O B. every 50 ft.
O C. every 100 ft
O D. near the discharge point,

Answers

Answer:

b because if u got the sewer and septic system

What efc number will enable a student to receive the full amount of a pall grant

Answers

[tex]\tt \ huge \orange{ oh }[/tex]

during a load test, a battery's voltage drops below a specific value. what action should the technician take?

A. Recharge and retest.
B. Allow battery to become fully discharged and retest.
C. immediately replace
D. None if above

Answers

Answer:

B

Explanation:

allow battery to become fully discharged and retest

When fully charged, a normal 12-volt automotive battery will have about 12.6 volts. The voltage just needs to fall to about 10.5 volts to be deemed fully discharged. The battery will suffer harm owing to severe sulfation if it falls below that level. Thus, option B is correct.

What battery's voltage drops below a specific value?

Changes in Voltage Occur During Discharge, The voltage of each cell is approximately 2.5 to 2.7 volts before the charging circuit is opened at the conclusion of a charge. The voltage of the cell rapidly reduces to roughly 2.1 volts within three or four minutes of the charging circuit being opened.

The voltage across the battery terminals decreases if a load is connected across the battery. The battery's internal resistance is to blame for this voltage drop. By measuring the open-circuit voltage and the voltage across the battery's terminals when a load is connected, we can determine the internal resistance.

Therefore, allow battery to become fully discharged and retest should the technician take.

Learn more about battery's here:

https://brainly.com/question/14922321

#SPJ2

Which of these does OSHA require employers to construct and install to minimize electrocution hazards?

Answers

Answer:

OSHA requires that the exposed and operating elements of an electrical installation, lighting, equipment, motors, machines, appliances, switches, controls, and enclosures must be constructed and installed so as to minimize workplace electrocution hazards.

Evaluate this design by describing the criteria it does or
does not meet

Answers

Answer:

Personal water filters solve the problem of having access to safe drinking water anywhere. They are available and affordable. The materials used to make them are durable. They protect, rather than harm, users. Overall, the benefits outweigh the risks.

Explanation:

i just know its right because its the sample response :D

The personal water filter meets the following requirements: It cleans tap water for domestic use, is reasonably priced, and is easy to transport.

What is water filter?

A water filter reduces water contamination through the use of a thin physical barrier, a chemical reaction, or a biological reaction to remove contaminants.

Conditions were satisfied in the example scenario:

Functionality: The personal water filter is capable of effectively removing germs and other pollutants from water.The filter is portable and convenient to use while traveling or camping because it is small and light.Affordability: The filter is a reasonable solution for those on a tight budget, costing around $20 or so.Durability: The filter can resist the wear and tear of continuous use thanks to its durable plastic design.

Unmet requirements:

Heavy Metal Removal: In locations where water sources are tainted with such substances, the filter's inability to remove heavy metals from water raises some questions.In locations where water supplies are contaminated with these bacteria, the filter's ineffectiveness at removing viruses may be a problem.In regions where only saltwater is accessible, the filter's inability to remove salt from the water could be a problem.Longevity: The filter is sturdy, however depending on usage, it might not last as long as other filtering systems and might need to be changed rather frequently.

Thus, these are the criteria it does or does not meet.

For more details regarding water purifiers, visit:

https://brainly.com/question/14265702

#SPJ2

What is the weight of a steel plate in the shape of a circle with a diameter of 10'? The steel weighs 14 Ib per Ft2

Answers

Width * Length * Thickness * Density = Weight.
48″ * 96″ * . 1875″ * 0.284 lb/in3 = 245 lb.
Other Questions
How did Justinian actions contribute to the fall of the Byzantine empire This is science not chemistry A Microscope has an ocular objective of 10x and a high power objective of 50x, what is the microsctotal magnification? Pil. Answer the following question:What do.you.meant by techical profession? what is the value of gravitation constant on the surface of the moon Match the line described on the left with the slope of the line on the right. y = 3--------------------------------------undefined 9x 3y = 18.--------------------------,------- - 2 the line through (5, 7) and (5, 8) -------0 the line through ( 4, 1) and (-1,7)--- 3. what is the color of cheese When it comes to inflation,what do central banks NOTwant?A rapid increases in the inflation rateB. inflation that goes up or down guided bythe central bankC. stable inflation ratesD. stability in imports and exports Exercise 1: NO MORE THAN THREE WORDS A. In addition to the reptiles, birds, mammals and insects which we see all around us, other groups that have succeeded out of water include scorpions, snails, crustaceans such as woodlice and land crabs, millipedes and centipedes, spiders and various worms. And we mustnt forget the plants , without whose prior invasion of the land none of the other migrations could have happened. What had to transfer from sea to land before any animals could migrate? The Plants B. Moving from water to land involved a major redesign of every aspect of life, including breathing and reproduction. Which TWO processes are mentioned as those in which animals had to make big changes as they moved onto land? Breathing and reproduction C. Ichthyosaurs were reptilian contemporaries of the dinosaurs, with fins and streamlined bodies. The fossils look like dolphins and they surely lived like dolphins, in the water. Which animals might ichthyosaurs have resembled? Dolphin D. The New Zealand Ministry of Health has found from research carried out over two decades that 6-10% of children in that country are affected by hearing loss. For what period of time has hearing loss in schoolchildren been studied in New Zealand? Over two decades E. It is probable that many undiagnosed children exist in the education system with ' invisible ' disabilities. What term is used to describe the hearing problems of schoolchildren which have not been diagnosed? Invisible disabilities Ex2: STEPWELLS Some wells are vast, open craters with hundreds of steps paving each sloping side, often in tiers. Others are more elaborate, with long stepped passages leading to the water via several storeys built from stone and supported by pillars, they also included pavilions that sheltered visitors from the relentless heat. But perhaps the most impressive features are the intricate decorative sculptures that embellish many stepwells, showing activities from fighting and dancing to everyday acts such as women combing their hair and churning butter. Down the centuries, thousands of wells were constructed throughout northwestern India, but the majority have now fallen into disuse; many are derelict and dry, as groundwater has been diverted for industrial use and the wells no longer reach the water table. Their condition hasnt been helped by recent dry spells: southern Rajasthan suffered an eight-year drought between 1996 and 2004. Today, following years of neglect, many of these monuments to medieval engineering have been saved by the Archaeological Survey of India, which has recognised the importance of preserving them as part of the countrys rich history. Tourists flock to wells in far-flung corners of northwestern India to gaze in wonder at these architectural marvels from 1,000 years ago, which serve as a reminder of both the ingenuity and artistry of ancient civilisations and of the value of water to human existence. Questions 68 Answer the questions below. Choose ONE WORD ONLY from the passage for each answer. Write your answers in boxes 68 on your answer sheet. Which part of some stepwells provided shade for people? Pavilions What type of serious climatic event, which took place in southern Rajasthan, is mentioned in the article? Who are frequent visitors to stepwells nowadays? Tourists HELPPGPPGPFPPDPSPPSS MEEEEK true or false? scientists who study processes that take millions of years cannot conduct experiments Instrucciones: Haz clic en el verbo y escribe la conjugacion correcta del verbo en el preterito. ( Look at the picture and read to answer the questions) Will Mark Brainliest. Help please due today is rhyme poetic, narrative or both In the years why was mother teresa more active in western countries? When analyzing an argument, the first task is to identify its premise or premises and its conclusion. Conclusion indicators are words or phrases that can help you identify which statement in an argument is the conclusion.Each argument shown next uses a conclusion indicator. Identify the conclusion indicator and the argument's conclusion. Type the indicator word or phrase into the space provided, and then select which statement best represents the argument's overall conclusion.Argument ASilver cars are more likely to be pulled over than any other kind of car. This is because there are more silver-colored cars on the road than any other kind of car. Kari drives an average-looking silver car to and from work everyday. We may infer that Kari is more likely to be pulled over.From this argument, type the conclusion indicator word or phrase here:Which statement best represents the conclusion of the argument?Kari is more likely to be pulled over.Kari drives an average-looking silver car to and from work everyday.Silver cars are more likely to be pulled over than any other kind of car.There are more silver-colored cars on the road than any other kind of car.Argument BScissors are not a toy. If you run with scissors, then you could get hurt. You could poke your eye out or cut yourself with the scissors if you fall. For these reasons, you should never run with scissors.From this argument, type the conclusion indicator word or phrase here:Which statement best represents the conclusion of the argument?You could poke your eye out or cut yourself with the scissors if you fall.If you run with scissors, then you could get hurt.Scissors are not a toy.You should never run with scissors.Argument CWe know that the natural world is governed by scientific laws of regularity. Those laws express predictable relationships that do not allow any wiggle room for variant outcomes. So, humans do not have free will. This is because the human body is as much a part of the natural world as any other physical object.From this argument, type the conclusion indicator word or phrase here:Which statement best represents the conclusion of the argument?Humans do not have free will.The natural world is governed by scientific laws of regularity.The human body is as much a part of the natural world as any other physical object.Scientific laws express predictable relationships that do not allow any wiggle room for variant outcomes. A male body is found in the woods near Peachtree Industrial Highway on the side of the dirt road. There is no evidence that the body was killed there, except that the man's tennis shoes appear to have a different color and texture of soil on the soles of his tennis shoes. What specialist would be called in to determine the location of where the body was moved from? Why? Indicate the answer choice that best completes the statemWrite each equa ton in standard form. Identify A, B, and cy=3/8x+5 Coucou Jai vraiment besoin daide merci tous What's Saprophytism?