In the accompanying diagram, if triangle OAB is rotated counterclockwise 90 deg about point O, which figure represents the image of this rotation?
(see image below)
Answers
Answer:
Answer option 2
Step-by-step explanation:
When a shape is rotated counterclockwise by 90°, each point of the shape is moved in a circular motion in the counterclockwise direction by 90° around the fixed point of rotation.
As the triangle is rotated about point O, the position of point O does not change (i.e. it is "fixed").
Line segment OA is horizontal in the original figure. When it is rotated 90° counterclockwise, it becomes vertical, where A is above O.
Line segment BA is vertical in the original figure. When it is rotated 90° counterclockwise, it becomes horizontal, where B is to the left of A.
Therefore, the figure that represents the image after the given rotation is the second answer option.
Answer:
Answer option number two.
Related Questions
You borrow $ 30,000 with an interest rate at 15% per year and will pay off the loan in three equal annual
payments, with the first payment occurring at the end of first year after the loan is made. The three equal
annual payments will be $13,139.40. Which of the following is true for your first payment at EOY 1?
a. Interest = $ 0; principal = $ 13,139.40
b. Interest = $ 13,139.40; principal = $0
c. Interest = $4,500; principal = $8,639.40
d. Interest = $4,500; principal = $13,139.40
Answers
The true statement about the first payment is Interest = $4,500; principal = $8,639.40
The correct answer choice is option C.
Which of the following is true for your first payment at EOY 1?Amount borrowed = $30,000
Interest rate = 15%
Annual payments = $13,139.40
Number of years = 3
Total payments at the end of 3 years = Annual payments × 3
= $39,418.20
Therefore,
Interest = $4,500;
principal = $8,639.40
Total = $13, 139.40 per year
Read more on loan:
https://brainly.com/question/26011426
#SPJ4
A gaseous mixture contains 431.0 Torr H₂(g), 388.5 Torr N₂(g), and 82.7 Torr Ar(g). Calculate the mole fraction, x, of each of 2 these gases. XH₂ = XN₂ = XAr =
Answers
the mole fractions are approximately:
XH₂ = 0.387
XN₂ = 0.348
XAr = 0.074
To calculate the mole fraction of each gas in the mixture, we need to divide the partial pressure of each gas by the total pressure of the mixture.
Given:
Partial pressure of H₂ (PH₂) = 431.0 Torr
Partial pressure of N₂ (PN₂) = 388.5 Torr
Partial pressure of Ar (PAr) = 82.7 Torr
Total pressure of the mixture (Ptotal) = PH₂ + PN₂ + PAr
Now, let's calculate the mole fraction (X) for each gas:
XH₂ = PH₂ / Ptotal
XN₂ = PN₂ / Ptotal
XAr = PAr / Ptotal
Substituting the given values into the equations:
XH₂ = 431.0 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
XN₂ = 388.5 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
XAr = 82.7 Torr / (431.0 Torr + 388.5 Torr + 82.7 Torr)
Calculating the values:
XH₂ ≈ 0.387
XN₂ ≈ 0.348
XAr ≈ 0.074
Therefore, the mole fractions are approximately:
XH₂ = 0.387
XN₂ = 0.348
XAr = 0.074
To learn more about fractions visit:
https://brainly.com/question/30154928
#SPJ11
b) For each of the following pairs of complexes, suggest with explanation the one that has the larger Ligand Fleid Spitting Energy (LFSE). (i) Tetrahedral [CoCl )^2 or tetrahedral [FeCL?
Answers
The tetrahedral complex [CoCl2]^2- has a larger Ligand Field Splitting Energy (LFSE) compared to the tetrahedral complex [FeCl4]^2-.
The LFSE of a complex is determined by the nature of the metal ion and the ligands surrounding it. In this case, we are comparing the tetrahedral complexes [CoCl2]^2- and [FeCl4]^2-.
The LFSE for tetrahedral complexes depends on the number of electrons in the d orbitals of the metal ion. Both cobalt (Co) and iron (Fe) are transition metals with d orbitals.
However, in the tetrahedral complex [CoCl2]^2-, cobalt (Co) has a d7 electronic configuration, whereas in the tetrahedral complex [FeCl4]^2-, iron (Fe) has a d6 electronic configuration.
The LFSE increases with the number of electrons in the d orbitals. Therefore, since [CoCl2]^2- has one more electron in the d orbitals compared to [FeCl4]^2-, it will have a larger LFSE.
Hence, the tetrahedral complex [CoCl2]^2- has a larger Ligand Field Splitting Energy (LFSE) than the tetrahedral complex [FeCl4]^2-.
Learn more about tetrahedral complex visit:
https://brainly.com/question/32357719
#SPJ11
b) After allowing 16% discount on the marked price of a watch, 13% Value Added Tax (VAT) was levied on it. If the watch was sold for Rs 4,746, calculate the marked price of the watch.
Answers
Let's denote the marked price as "M."
Given:
Selling price after discount and VAT = Rs 4,746
Discount = 16%
VAT = 13%
Step 1: Calculating the selling price before VAT
Let's assume the selling price before VAT as "X."
X = Selling price after VAT / (1 + VAT rate)
X = Rs 4,746 / (1 + 0.13)
X = Rs 4,746 / 1.13
X ≈ Rs 4,200
Step 2: Calculating the marked price before discount
Let's assume the marked price before the discount as "Y."
Y = Selling price before VAT / (1 - Discount rate)
Y = Rs 4,200 / (1 - 0.16)
Y = Rs 4,200 / 0.84
Y ≈ Rs 5,000
Therefore, the marked price of the watch would be approximately Rs 5,000.
Please note that the actual marked price may have been rounded to the nearest value in the given calculation.
?
QUESTION 2 5 points a) Excavated soil material from a building site contains arsenic. When the soil was analysed for the arsenic, it was determined that the arsenic concentration in the soil mass was
Answers
The arsenic concentration in the excavated soil from the building site was not specified in the question.
What was the concentration of arsenic in the soil material from the building site?The question provides information about the presence of arsenic in the excavated soil material from a building site but does not give the specific concentration value.
Arsenic is a toxic element, and its presence in soil can pose significant health and environmental risks. To assess the potential hazards and plan for appropriate remediation measures, knowing the exact concentration of arsenic in the soil is crucial.
The concentration of arsenic is typically measured in parts per million (ppm) or milligrams per kilogram (mg/kg) of soil.
Without the provided concentration value, it is impossible to determine the level of risk or the appropriate actions needed. Further information or data would be required to make any assessments or recommendations related to the arsenic-contaminated soil.
Learn more about excavated soil
brainly.com/question/25157835
#SPJ11
43. Amino acids are named based on the identity of 44. A mutation in the primary sequence causes a disruption in protein folding and results in hemoglobin S or sickle-shaped red blood cells. What is t
Answers
The name of the condition that results from a mutation in the primary sequence, causing a disruption in protein folding and resulting in sickle-shaped red blood cells is called sickle cell anemia.
The sickle cell anemia results from a single amino acid mutation in the hemoglobin protein. Instead of glutamic acid, valine is present. This change causes the protein to fold differently than it should. The protein fiber becomes deformed and sticky, causing the red blood cells to become sticky and rigid.
The sickle-shaped red blood cells become lodged in small capillaries, leading to tissue damage, anemia, and pain. The name of the condition is sickle cell anemia, and it is a recessive genetic disorder. People who inherit one copy of the mutated hemoglobin gene are carriers of the disease, while people who inherit two copies of the mutated gene will have sickle cell anemia.
Learn more about glutamic acid here:
https://brainly.com/question/29807201
#SPJ11
Complete question is:
A mutation in the primary sequence causes a disruption in protein folding and results in hemoglobin S or sickle-shaped red blood cells. What is this condition called?
A simply supported T beam has a simple span of 3m. The thickness of the slab is 110mm. The width of its web is 350mm. If the center to center spacing between beams is 2m, determine the effective flange width of the T beam.
Answers
The effective flange width of the given T beam with a simple span of 3m, a slab thickness of 110mm, and a web width of 350mm is calculated to be 1.65 meters.
The effective flange width represents the distance from the centerline of the web to the edge of the flange where it can contribute to the load-carrying capacity of the T beam. In a T beam, the flange is responsible for resisting bending stresses.
Given that the centre-to-centre spacing between beams is 2m, we need to determine the distance from the centerline of the web to the edge of the flange. This can be calculated by subtracting the width of the web from the centre-to-centre spacing.
The width of the web is given as 350mm, which needs to be converted to meters (0.35m). Subtracting the width of the web from the centre-to-centre spacing gives us the effective flange width:
Effective flange width = 2m - 0.35m
Effective flange width = 1.65m
Therefore, the effective flange width of the T beam is 1.65 meters.
To learn more about simple span refer:
https://brainly.com/question/29939115
#SPJ11
A 47.6g sample was found to consist of 35.0% oxygen by mass with
the remaining mass being calcium, calculate the mass of calcium in
the sample.
Answers
The mass of calcium in the sample is 30.94 g.
To calculate the mass of calcium, we first need to determine the mass of oxygen in the sample. We know that the sample consists of 35.0% oxygen by mass, so we can calculate the mass of oxygen using the given sample mass of 47.6 g:
Mass of oxygen = 35.0% * 47.6 g = 0.35 * 47.6 g = 16.66 g.
Since the remaining mass in the sample is calcium, we can calculate the mass of calcium by subtracting the mass of oxygen from the sample mass:
Mass of calcium = Sample mass - Mass of oxygen = 47.6 g - 16.66 g = 30.94 g.
Therefore, the mass of calcium in the sample is 30.94 g.
Know more about oxygen here:
https://brainly.com/question/33311650
#SPJ11
A ball is kicked upward with an initial velocity of 68 feet per second. The ball's height, h (in feet), from the ground is modeled by h = negative 16 t squared 68 t, where t is measured in seconds. What is the practical domain in this situation? a. 0 less-than-or-equal-to t less-than-or-equal-to 4.25 b. All real numbers c. 0 less-than-or-equal-to t less-than-or-equal-to 2.125 d. 0 less-than-or-equal-to t less-than-or-equal-to 17
Answers
Answer: a. 0 ≤ t ≤ 4.25
Step-by-step explanation: To determine the practical domain in this situation, we need to consider the physical constraints of the problem. The practical domain refers to the range of values for the independent variable, t, that makes sense in the given context.
In this case, since we are modeling the height of a ball kicked upward, time (t) cannot be negative because it represents the duration since the ball was kicked. Therefore, the value of t must be non-negative.
Additionally, to find the time it takes for the ball to reach its maximum height and fall back to the ground, we can set the equation h = 0 and solve for t.
Using the given equation: h = -16t^2 + 68t
0 = -16t^2 + 68t
Dividing the equation by 4 gives us:
0 = -4t^2 + 17t
Factoring out t, we get:
0 = t(-4t + 17)
From this equation, we can see that one solution is t = 0, which represents the starting point when the ball is kicked.
The other solution is obtained when -4t + 17 = 0:
4t = 17
t = 17/4
t = 4.25
Therefore, the ball reaches the ground again at t = 4.25 seconds.
Considering the physical context, we can conclude that the practical domain for this situation is:
0 ≤ t ≤ 4.25
This corresponds to option (a) 0 ≤ t ≤ 4.25.
what is the relationship between the pair of angles AXC and BXC shown in the diagram
Answers
Angles ZAXC and BXC form a linear pair.the correct answer is C.
Based on the given diagram, the relationship between angles ZAXC and BXC can be determined.
Let the diagram, we can see that angles ZAXC and BXC share the same vertex, which is point X. Additionally, the two angles are formed by intersecting lines, where line ZX intersects line XC at point A and line BX intersects line XC at point B.
When two lines intersect, they form various pairs of angles with specific relationships. Let's analyze the options provided:
A. They are corresponding angles:
Corresponding angles are formed when a transversal intersects two parallel lines. In the given diagram, there is no indication that the lines ZX and BX are parallel. Therefore, angles ZAXC and BXC cannot be corresponding angles.
B. They are complementary angles:
Complementary angles are two angles that add up to 90 degrees. In the given diagram, there is no information to suggest that angles ZAXC and BXC add up to 90 degrees. Therefore, they are not complementary angles.
C. They are a linear pair:
A linear pair consists of two adjacent angles formed by intersecting lines, and their measures add up to 180 degrees. In the given diagram, angles ZAXC and BXC are adjacent angles, and their measures indeed add up to 180 degrees. Therefore, they form a linear pair.
Measure of two angle are
∠AXC = 60
∠BXC = 120
Now,
we get;
∠AXC + ∠BXC = 60 + 120
= 180
D. They are vertical angles:
Vertical angles are formed by two intersecting lines and are opposite each other. In the given diagram, angles ZAXC and BXC are not opposite each other. Therefore, they are not vertical angles.
option C is correct.
For more such questions on linear pair visit:
https://brainly.com/question/18047626
#SPJ8
Note: The complete questions is
What is the relationship between the pair of angles ZAXC and BXC shown
in the diagram?
A. They are corresponding angles.
B. They are complementary angles.
C. They are a linear pair.
D. They are vertical angles.
Solvents have a multi-purpose role in pharmaceutical processing and need to be chosen with care for the different processing steps of the active pharmaceutical ingredient (API), such as chemical reaction, separation and purification. In these processes, very often a reaction may take place in one solvent (S1) and the next processing step (e.g. another reaction, crystallisation, extraction or washing) may require a different solvent (S2) because the process performance is better than if using the original (S1). Solvent swap, or solvent exchange, is therefore a common and important task in API production within the pharmaceutical industry. The solvent swap task is the operation performed to remove an original solvent (S1) that is used in an earlier processing step and at the same time replace it with another solvent (S2) that is more suitable for the next processing step. The solvent swap task is performed as a separation task that is usually based on volatility difference, immiscibility difference or size difference. Batch distillation is often considered as the operation to perform the solvent swap. In the following, it is initially assumed that the solvent swap step will be followed by a crystallisation step for which the original solvent is not as suitable, for example, because the API would crystallise as needles/needle structures hampering the filtration process subsequent to crystallisation. Crystallisation steps are usually employed for the purification and recovery steps of the APIs, and the solvent selection will have an impact on the solid solubility and crystal structure. For the solvent swap, the swap solvent (S2) is somehow mixed with the original solvent (S1), which contains the API, which has been fed to the bottom of a regular batch distillation column. The original solvent is distilled off and collected as the top product whilst the swap solvent together with the API are collected in the still at the end and moved to the next processing step. For the downstream crystallisation process, one needs to make sure that S2 allows for the product recovery required. For example, cooling crystallisation requires a strong temperature dependence of the API solubility in S2. Special care needs to be taken, however, that the API does not crystallise prematurely during distillation.
1. Proper process control is as important for batch processing as it is for continuous manufacturing. Consider a solvent swap process where the original solvent (S1) and the swap solvent (S2) are pure solvents and propose an operating procedure and a control scheme for the regular batch distillation column when the objective is to keep a high production rate and safe operation, and where the process specification on allowable amount of original solvent remaining in the still is very low.
Assume also that the original solvent is to be recycled back to the reaction step, hence high purity is required.
Answers
Solvent swap, or solvent exchange, is a common and important task in pharmaceutical processing. It involves removing the original solvent used in one processing step and replacing it with a different solvent that is more suitable for the next step. This is typically done through batch distillation, where the original solvent is distilled off and collected as the top product, while the new solvent is collected with the active pharmaceutical ingredient (API) at the bottom. The solvent swap is performed to improve process performance and ensure the desired product recovery in downstream steps like crystallisation.
Solvent swap is crucial in pharmaceutical processing because different solvents may be required for different processing steps of the API. For example, a reaction may take place in one solvent, but the next step may require a different solvent for better performance. The solvent swap is performed as a separation task based on volatility difference, immiscibility difference, or size difference. Batch distillation is often used for this operation. In the case of downstream crystallisation, the choice of the swap solvent is important for the desired product recovery. Cooling crystallisation, for instance, requires a strong temperature dependence of the API solubility in the new solvent. Care must be taken to prevent premature crystallisation during distillation. Furthermore, since the original solvent is often recycled back to the reaction step, high purity is required.
Know more about distillation here:
https://brainly.com/question/31829945
#SPJ11
The BOD: of a municipal wastewater is determined to be 168 mg/L at 15°C. The BOD rate constant, k is known to be 0.18 day at 15°C. Compute the BOD5 of the sample at 20°C. What would be the remainin
Answers
To calculate the BOD5 of the sample at 20°C, we need additional information about the BOD rate constant at that temperature. Without that information, we cannot provide a direct calculation or answer.
Biological Oxygen Demand (BOD) is a measure of the amount of dissolved oxygen consumed by microorganisms while decomposing organic matter in water. The BOD rate constant (k) determines the rate at which BOD decreases over time. To calculate the BOD5 (BOD after 5 days), we need the BOD rate constant at 20°C.
Assuming we have the BOD rate constant at 20°C, we can use the following formula to calculate BOD5 at 20°C:
BOD5(20°C) = BOD(15°C) * (k20 / k15)^(t5 - t15)
Where:
BOD5(20°C) is the BOD5 at 20°C,
BOD(15°C) is the initial BOD at 15°C (168 mg/L),
k20 is the BOD rate constant at 20°C,
k15 is the BOD rate constant at 15°C (0.18 day),
t5 is the duration in days (5 days), and
t15 is the duration in days at 15°C (assumed as 5 days).
Without the value for k20, we cannot calculate the BOD5 at 20°C or determine the remaining BOD.
To determine the BOD5 of the sample at 20°C and the remaining BOD, we need the BOD rate constant at 20°C. Once we have that information, we can use the provided formula to calculate the BOD5 at 20°C.
To know more about temperature visit:
https://brainly.com/question/27944554
#SPJ11
The CO concentration in a stack is 345 ppm, the stack diameter is 24 inches, and the stack gas velocity is 11 ft/sec. The gas temperature and pressure are 355°F and 1 atm. Determine the CO mass emission rate in kg/day. Please show all steps
Answers
CO concentration in stack = 345 ppmStack diameter = 24 inchesStack gas velocity = 11 ft/secGas temperature = 355°F and Pressure = 1 atmWe need to find the CO mass emission rate in kg/day.
= πD²/4Given Diameter
= 24 inches = 2 ftSo, A
= π(2/2)²/4 = 0.306 ft
²Q = A × VQ = 0.306 × 11
= 3.366 ft³/s
Convert flow rate to m³/s3.366 ft³/s × 0.02832 = 0.0953 m³/s
= Molecular weight of CO
= 28So,CO = 345 × 0.0953 × 28 / 24.45
= 0.115 kg/s0.115 × 3600 × 24
= 9936 kg/day.
So, the CO mass emission rate in kg/day is 9936 kg/day.
To know more about diameter visit:
https://brainly.com/question/30862855
#SPJ11
The CO concentration in a stack is 345 ppm, the stack diameter is 24 inches, and the stack gas velocity is 11 ft/sec. The gas temperature and pressure are 355°F and 1 atm. The CO mass emission rate in kg/day is 9936 kg/day.
CO concentration in stack = 345 ppm
Stack diameter = 24 inches
Stack gas velocity = 11 ft/sec
Gas temperature = 355°F and Pressure = 1 atm
We need to find the CO mass emission rate in kg/day.
= πD²/4
Given Diameter
= 24 inches
= 2 ft
So, A = π(2/2)²/4
= 0.306 ft
²Q = A × VQ = 0.306 × 11
= 3.366 ft³/s
Convert flow rate to m³/s3.366 ft³/s × 0.02832
= 0.0953 m³/s
= Molecular weight of CO
= 28So,CO
= 345 × 0.0953 × 28 / 24.45
= 0.115 kg/s0.115 × 3600 × 24
= 9936 kg/day.
So, the CO mass emission rate in kg/day is 9936 kg/day.
To know more about diameter visit:
brainly.com/question/30862855
#SPJ11
Directions: Complete the problem set, showing all work for problems below. 1. Calculate the molar concentration of a solution of a sample with 135 moles in 42.5 L of solution.
Answers
The molar concentration of a solution can be calculated by dividing the number of moles of solute by the total volume of the solution in liters.
The molar concentration of a solution of a sample with 135 moles in 42.5 L of solution can be calculated as follows:
To find the molar concentration of a solution, the formula is used;
Molarity (M) = Moles of solute (n) / Volume of solution (V)Molarity (M)
= 135 moles / 42.5 L
= 3.176 M (Answer)
Molarity is expressed in terms of moles of solute per liter of solution.
This means that the number of moles of solute is divided by the total volume of the solution in liters (L). For example, if a solution contains 1 mole of solute in 1 liter of solution, its molar concentration would be 1 M.
This is a common unit used in chemistry to express the concentration of solutions.
To know more about molar concentration visit:-
https://brainly.com/question/21841645
#SPJ11
Answer:
The molar concentration of the solution is 3.18 moles/L.
Step-by-step explanation:
To calculate the molar concentration of a solution, we use the formula:
Molar concentration (C) = moles of solute / volume of solution (in liters)
Given:
Moles of solute = 135 moles
Volume of solution = 42.5 L
Substituting the values into the formula:
C = 135 moles / 42.5 L
C = 3.18 moles/L
To know more about solution
https://brainly.in/question/56263721
#SPJ11
With an aid of a diagram, Discuss the conditions of equilibrium for the following: 1. Floating body 2. Submerged body
Answers
Floating and submerged bodies require equal weight, buoyant force, and gravity forces to maintain equilibrium. Both require the center of gravity beneath the center of buoyancy.
1. Floating body: When an object floats in a fluid, there are three conditions for equilibrium: the weight of the floating object, the buoyant force, and the force of gravity acting on the object. The weight of the floating object must equal the buoyant force to keep the object floating, and the center of gravity must be beneath the center of buoyancy.The diagram below illustrates the conditions of equilibrium for a floating body:
2. Submerged body:When a body is submerged in a fluid, the forces of gravity and buoyancy act on the object to keep it in equilibrium. In order for an object to be in equilibrium, the weight of the object must be equal to the buoyant force, and the center of gravity must be at the center of buoyancy. The diagram below illustrates the conditions of equilibrium for a submerged body:
In summary, the conditions of equilibrium for a floating body and a submerged body are the same: the weight of the object must equal the buoyant force, and the center of gravity must be at the center of buoyancy.
To know more about buoyancy Visit:
https://brainly.com/question/30641396
#SPJ11
An individual's per kg expenditure on coffee is distributed with mean $2.32 and variance 0.09 If each individual in the population drinks 3 kg of tea and 2 kg of coffee, the mean total expenditure an beverages is $ with a variance of □, If T and C have a bivariate normal distribution with covariance zero, the mean total expenditure an beverages is $□ with a variance of □. If X and Y have a bivariate distribution with covariance zero, this implies that the variables show
Answers
The mean total expenditure on beverages is $736 with a variance of $8.1912.
If X and Y have a bivariate distribution with covariance zero, this implies that the variables show no linear relationship.
Given that an individual's per kg expenditure on coffee is distributed with mean $2.32 and variance 0.09.
Each individual in the population drinks 3 kg of tea and 2 kg of coffee.
Let T and C be the amount spent on tea and coffee respectively by an individual.
Then,
Total expenditure on coffee = 2 × 2.32 × 100 = $232
and,
Total expenditure on tea = 3 × 1.68 × 100 = $504
We know that the covariance of T and C is zero.
Thus, Mean of the total expenditure on beverages = 232 + 504 = $736,
The variance of the total expenditure on beverages = 4 × variance of expenditure on coffee + 9 × variance of expenditure on tea
= 4 × 0.09 × (2.32)² + 9 × 0.04 × (1.68)²
= $8.1912
Hence, the mean total expenditure on beverages is $736 with a variance of $8.1912.
If X and Y have a bivariate distribution with covariance zero, this implies that the variables show no linear relationship.
To know more about linear relationship visit:
https://brainly.com/question/29066440
#SPJ11
nts Incorrect Question 2 0/2.5 pts At an abandoned waste site, you find a 10,000 L tank contaminated with Chemical Z at a concentration of 2.7 mg/L. You cannot pump the water into the local sewer unless the concentration is below 0.5 mg/L. One idea for treating the water is to add activated carbon until you reach the allowable concentration, then you can filter out the carbon and dispose of it at a hazardous waste landfill. Lab tests show that the linear partitioning coefficient for Chemical Z and the activated carbon is 4.1 L/g. Calculate how much activated carbon (in kg) to purchase. 4 Enter your final answer with 2 decimal places. 189.42
Answers
We are given a 10,000 L tank contaminated with Chemical Z at a concentration of 2.7 mg/L.
We know that,
Ci = 2.7 mg/LCe = 0.5 mg/LPC = 4.1 L/g
Volume of contaminated water = 10,000 L
= 10,000,000 mL Putting all the values in the formula, Mass of activated carbon = (10,000,000 mL × (2.7 − 0.5))/4.1 = 6,900,000/4.1
= 1,682,926.8 mL
We need to convert this volume to mass, Mass = volume × density Density of activated carbon = 0.5 g/mLTherefore, Mass of activated carbon
= 1,682,926.8 mL × 0.5 g/mL
= 841,463.4 g
= 841.46 kg
To know more about concentration, visit :
https://brainly.com/question/30862855
#SPJ11
To treat the contaminated water and bring the concentration of Chemical Z below 0.5 mg/L, approximately 6.59 kg of activated carbon should be purchased.
To calculate the amount of activated carbon needed to treat the contaminated water, we can use the linear partitioning coefficient. This coefficient tells us the ratio of the concentration of Chemical Z in the activated carbon to the concentration in the water. In this case, the coefficient is 4.1 L/g.
First, we need to determine the mass of Chemical Z in the tank. The concentration is given as 2.7 mg/L, and the volume of the tank is 10,000 L. Multiplying these values gives us 27,000 mg of Chemical Z in the tank.
Next, we divide the mass of Chemical Z in the tank by the linear partitioning coefficient to find the mass of activated carbon needed. In this case, we divide 27,000 mg by 4.1 L/g, which gives us 6,585.37 g.
To convert the mass to kilograms, we divide by 1000. So, the amount of activated carbon to purchase is 6.58537 kg.
Therefore, the answer is 6.59 kg (rounded to two decimal places).
Learn more about concentration
https://brainly.com/question/30862855
#SPJ11
QUESTION 7: Consider the function f(x)=x3−4x+1 a) Find the interval(s) in which the function f(x) is increasing and the interval(s) in which the function is decreasing. b) Find the interval(s) in which the function f(x) is concave up and the interval(s) in which the function is concave down. c) Sketch the graph of the function f(x)
Answers
The function f(x) is increasing on the interval (-2/√3, 2/√3) and decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞).The given function is [tex]f(x) = x^3 - 4x + 1.[/tex].
a) To find the intervals where the function is increasing or decreasing, we need to determine where the derivative of the function is positive or negative. The derivative of [tex]f(x) is f'(x) = 3x^2 - 4[/tex].
To find the critical points, we set f'(x) = 0 and solve for x:
[tex]3x^2 - 4 = 0[/tex]
[tex]3x^2 = 4[/tex]
[tex]x^2 = 4/3[/tex]
x = ± √(4/3)
x = ± 2/√3
We have two critical points: x = -2/√3 and x = 2/√3.
Now, we can test the intervals between these critical points and beyond to determine where the function is increasing or decreasing.
For x < -2/√3, f'(x) < 0, so the function is decreasing.
For -2/√3 < x < 2/√3, f'(x) > 0, so the function is increasing.
For x > 2/√3, f'(x) < 0, so the function is decreasing.
Therefore, the function f(x) is increasing on the interval (-2/√3, 2/√3) and decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞).
b) To find the intervals where the function is concave up or concave down, we need to determine where the second derivative of the function is positive or negative. The second derivative of f(x) is f''(x) = 6x.
Since the second derivative is always positive (6x > 0), the function is concave up for all x.
c) To sketch the graph of the function, we can use the information we found in parts a) and b). The graph will be increasing on the interval (-2/√3, 2/√3), decreasing on the intervals (-∞, -2/√3) and (2/√3, ∞), and concave up for all x. We can also plot the critical points at x = -2/√3 and x = 2/√3.
Please note that the sketch may vary based on the scale and accuracy of the graph.
To know more about derivative visit:
https://brainly.com/question/25324584
#SPJ11
A peach is 7 times as heavy as an olive. The peach also weighs 900 grams more than the olive. What is the total weight in kilograms for the peach and olive?
Answers
We are also told that the peach weighs 900 grams more than the olive. Mathematically, this can be represented as 7x = x + 900.
Now, we can solve this equation to find the weight of the olive:
7x - x = 900
6x = 900
x = 150
Therefore, the weight of the olive is 150 grams. The weight of the peach is 7 times the weight of the olive, which is 7 * 150 = 1050 grams.
To calculate the total weight in kilograms, we need to convert the weights from grams to kilograms:
Weight of the olive = 150 grams = 0.15 kilograms
Weight of the peach = 1050 grams = 1.05 kilograms
So, the total weight of the peach and olive is 0.15 + 1.05 = 1.2 kilograms.
Liquid octane (CH_3(CH_2)_6CH_3) will react with goseous axygen (O_2) to produce gaseous carbon dioxide (CO_2) and gaseous water (H_2O). Suppose 4.6 g of octane is mixed with 26.4 g of oxygen. Caiculate the maximum mass of water that could be produced by the chemical reaction. Round your answer to 2. significant digits.
Answers
Liquid octane[tex](CH_3(CH_2)_6CH_3)[/tex] will react with gaseous oxygen[tex](O_2)[/tex] to produce gaseous carbon dioxide [tex](CO_2)[/tex] and gaseous water [tex](H_2O).[/tex] the maximum mass of water that could be produced in the chemical reaction is approximately 10.70 grams.
To calculate the maximum mass of water produced in the chemical reaction between octane[tex](C_8H_1_8)[/tex] and oxygen [tex](O_2)[/tex], we need to determine the limiting reactant. This is done by comparing the moles of each reactant.
First, let's calculate the number of moles of octane and oxygen:
[tex]Molar mass of octane (C_8H_1_8) = 114.22 g/mol[/tex]
[tex]Molar mass of oxygen (O_2) = 32.00 g/mol[/tex]
[tex]Moles of octane = mass / molar mass = 4.6 g / 114.22 g/mol ≈ 0.0402 mol[/tex]
[tex]Moles of oxygen = mass / molar mass = 26.4 g / 32.00 g/mol ≈ 0.825 mol[/tex]
The balanced chemical equation for the reaction is:
[tex]2C_8H_1_8 + 25O_2[/tex]→ [tex]16CO_2 + 18H_2O[/tex]
From the equation, we can see that the mole ratio of oxygen to water is 25:18. Therefore, the moles of water produced will be:
[tex]Moles of water = (moles of oxygen) * (18 moles of water / 25 moles of oxygen) = 0.825 mol * (18/25) ≈ 0.594 mol[/tex]
To find the maximum mass of water produced, we multiply the moles of water by its molar mass:
[tex]Mass of water = moles of water * molar mass of water = 0.594 mol * 18.02 g/mol ≈ 10.70 g[/tex]
Therefore, the maximum mass of water that could be produced in the chemical reaction is approximately 10.70 grams.
Learn more about limiting reactant
https://brainly.com/question/33417913
#SPJ11
The maximum mass of water that could be produced by the chemical reaction is [tex]6.510[/tex] g (rounded to 2 significant digits).
To calculate the maximum mass of water produced by the chemical reaction between octane and oxygen, we first need to determine the limiting reactant. The limiting reactant is the reactant that is completely consumed and determines the maximum amount of product that can be formed.
The balanced chemical equation for the reaction is:
[tex]\[2C_8H_{18} + 25O_2 \rightarrow 16CO_2 + 18H_2O\][/tex]
From the equation, we can see that the stoichiometric ratio between octane and water is [tex]2:18[/tex], or [tex]1:9[/tex].
First, let's calculate the number of moles for each reactant:
Number of moles of octane:
[tex]\[n_{\text{octane}} = \frac{m_{\text{octane}}}{M_{\text{octane}}}\][/tex]
[tex]\[n_{\text{octane}} = \frac{4.6 \, \text{g}}{114.22 \, \text{g/mol}}\][/tex]
Number of moles of oxygen:
[tex]\[n_{\text{oxygen}} = \frac{m_{\text{oxygen}}}{M_{\text{oxygen}}}\][/tex]
[tex]\[n_{\text{oxygen}} = \frac{26.4 \, \text{g}}{32 \, \text{g/mol}}\][/tex]
Next, we compare the moles of octane to the moles of water to determine the limiting reactant:
[tex]\[\frac{n_{\text{octane}}}{1} = \frac{n_{\text{water}}}{9}\][/tex]
Solving for [tex]\(n_{\text{water}}\)[/tex], we find:
[tex]\[n_{\text{water}} = \frac{n_{\text{octane}}}{1} \times \frac{9}{1} = 9n_{\text{octane}}\][/tex]
Finally, we can calculate the maximum mass of water produced:
[tex]\[m_{\text{water}} = n_{\text{water}} \times M_{\text{water}}\][/tex]
[tex]\[m_{\text{water}} = 9n_{\text{octane}} \times M_{\text{water}}\][/tex]
To calculate the maximum mass of water produced, we need to determine the limiting reactant first.
1. Calculate the number of moles for each reactant:
Number of moles of octane:
[tex]\(n_{\text{octane}} = \frac{m_{\text{octane}}}{M_{\text{octane}}}\)[/tex]
[tex]\(n_{\text{octane}} = \frac{4.6 \, \text{g}}{114.22 \, \text{g/mol}} = 0.04024 \, \text{mol}\)[/tex]
Number of moles of oxygen:
[tex]\(n_{\text{oxygen}} = \frac{m_{\text{oxygen}}}{M_{\text{oxygen}}}\)[/tex]
[tex]\(n_{\text{oxygen}} = \frac{26.4 \, \text{g}}{32 \, \text{g/mol}} = 0.825 \, \text{mol}\)[/tex]
2. Determine the limiting reactant:
From the balanced equation, the stoichiometric ratio between octane and water is [tex]2:18[/tex], or [tex]1:9[/tex]. Since the molar ratio between octane and water is [tex]1:9[/tex], and the number of moles of octane is [tex]0.04024[/tex]mol, we can calculate the moles of water produced:
[tex]\(n_{\text{water}} = 9 \times n_{\text{octane}} = 9 \times 0.04024 \, \text{mol} = 0.361 \, \text{mol}\)[/tex]
3. Calculate the maximum mass of water produced:
[tex]\(m_{\text{water}} = n_{\text{water}} \times M_{\text{water}}\)[/tex]
[tex]\(m_{\text{water}} = 0.361 \, \text{mol} \times 18.01528 \, \text{g/mol} = 6.510 \, \text{g}\)[/tex]
Therefore, the maximum mass of water that could be produced by the chemical reaction is [tex]6.510[/tex] g (rounded to 2 significant digits).
Learn more about stoichiometric ratio
https://brainly.com/question/6907332
#SPJ11
For the nonhomogenous system, 2a−4b+5c=8
14b−7a+4c=−28
c+3a−6b=12
Answers
The solution to the nonhomogeneous system is a = 4, b = 0, and c = 0.
To solve the nonhomogeneous system of equations:
2a - 4b + 5c = 8
14b - 7a + 4c = -28
c + 3a - 6b = 12
Step 1: Rearrange the equations to put them in standard form:
2a - 4b + 5c = 8 ---> Equation 1
-7a + 14b + 4c = -28 ---> Equation 2
3a - 6b + c = 12 ---> Equation 3
Step 2: Use the method of substitution or elimination to solve the system. Let's use the elimination method:
Multiply Equation 1 by -7 and Equation 2 by 2:
-14a + 28b - 35c = -56 ---> Equation 4
-14a + 28b + 8c = -56 ---> Equation 5
Subtract Equation 4 from Equation 5 to eliminate the "a" terms:
0 + 0 - 43c = 0
-43c = 0
Since -43c = 0, c must be equal to 0.
Substitute c = 0 into Equation 1:
2a - 4b + 5(0) = 8
2a - 4b = 8
Multiply Equation 3 by 2:
6a - 12b + 2c = 24 ---> Equation 6
Substitute c = 0 into Equation 6:
6a - 12b + 2(0) = 24
6a - 12b = 24
Now we have two equations:
2a - 4b = 8 ---> Equation 7
6a - 12b = 24 ---> Equation 8
Divide Equation 8 by 6:
a - 2b = 4
Multiply Equation 7 by 3:
6a - 12b = 24
Subtract the new Equation 7 from Equation 8 to eliminate the "a" terms:
0 + 0 - 36b = 0
-36b = 0
Since -36b = 0, b must also be equal to 0.
Now, substitute b = 0 into Equation 7:
2a - 4(0) = 8
2a = 8
Divide both sides by 2:
a = 4
Learn more about nonhomogeneous system:
https://brainly.com/question/32263699
#SPJ11
Determine a safe drinking water concentration (in ppb) for cadmium in the drinking water of a women's health club. The RfD for cadmium is 5 x 10^-4 mg/kg-day.
Answers
If the RfD for cadmium is 5 x 10⁻⁴ mg/kg-day, then a safe drinking water concentration (in ppb) for cadmium in the drinking water of a women's health club is 15 ppb.
To find a safe drinking water concentration, follow these steps:
Daily intake (in mg/day) = RfD x Body weight (in kg) = 5 x 10⁻⁴ x 60 = 0.03 mg/dayLet's assume an average consumption of 2 liters per day.The concentration of cadmium in the drinking water in ppb can be calculated as follows:
Concentration (in ppb) = Daily intake / Water consumption (in mL) x 10⁶ = 0.03 / 2000 x 10⁶ = 15 ppb
Learn more about safe drinking water concentration:
https://brainly.com/question/32014868
#SPJ11
If 1800 m°/d of wastewater from an industry has a BODs of 190
mg/L and k = 0.17/day (base 10)
a. How much oxygen is required to satisfy the demand for BODs of
this residue assuming that 1 kg of oxygen must be supplied by
kilogram of final BOD in the residue
b. What is the population equivalent of these wastes (besed in
BOD5)?
Answers
(a) The amount of oxygen required to satisfy the demand for BODs in this residue is 578,100 kg/d.
(b) The population equivalent of these wastes, based on BOD₅, is 5,700,000 population.
a. To calculate the amount of oxygen required to satisfy the demand for BODs, we can use the formula:
Oxygen required = Flow rate * BODs * k
Given that the flow rate is 1800 m³/d, the BODs is 190 mg/L, and k is 0.17/day, we can substitute these values into the formula:
Oxygen required = 1800 m³/d * 190 mg/L * 0.17/day
To ensure consistent units, we need to convert the flow rate from m³/d to L/d:
1800 m³/d * 1000 L/m³ = 1,800,000 L/d
Now we can substitute this value into the formula:
Oxygen required = 1,800,000 L/d * 190 mg/L * 0.17/day
Simplifying the calculation:
Oxygen required = 578,100,000 mg/d
To convert mg to kg, we divide by 1000:
Oxygen required = 578,100 kg/d
Therefore, the amount of oxygen required to satisfy the demand for BODs in this residue is 578,100 kg/d.
b. To calculate the population equivalent of these wastes based on BOD₅, we need to know the BOD₅ value for the wastewater. The BOD₅ value represents the amount of dissolved oxygen consumed over a 5-day period.
If we assume the BOD₅ value is the same as the BODs value, which is 190 mg/L, we can use the following formula:
Population equivalent = (Flow rate * BOD₅) / 60 g/day
Given that the flow rate is 1800 m³/d and the BOD₅ is 190 mg/L, we can substitute these values into the formula:
Population equivalent = (1800 m³/d * 190 mg/L) / 60 g/day
To ensure consistent units, we need to convert the flow rate from m³/d to L/d:
1800 m³/d * 1000 L/m³ = 1,800,000 L/d
Now we can substitute this value into the formula:
Population equivalent = (1,800,000 L/d * 190 mg/L) / 60 g/day
Simplifying the calculation:
Population equivalent = 5,700,000 population
Therefore, the population equivalent of these wastes, based on BOD₅, is 5,700,000 population.
Know more about population equivalent:
https://brainly.com/question/33840792
#SPJ11
A reverse osmosis plant is needed to be installed near a village where the drinking water demand is 3000 cubic meter per day. Feed water is extracted from underground at a pressure of 14 bars and sent to single stage reverse osmosis plant. RO element available in market can process up to 40 cubic meter per hr. and a single vessel can accommodate maximum 25 elements. Analysis of underground water of that area shows 3000 ppm salts, where the majority is NaCl. If health organization demands less than 700 ppm of TDS in drinking water, provide the following things.
1. Suggest the feed required for required flow rate of clean water
Answers
162.76 cubic meters per hour of feed water is required to produce 125 cubic meters per hour of clean water.
Feed Required for Required Flow Rate of Clean Water:
The daily water demand is 3000 cubic meters per day, and we can easily calculate the hourly water demand using the following formula:
H= 24Q
Where, H = Hourly Water Demand
Q = Daily Water Demand / 24H = 3000 / 24H = 125 cubic meters per hour
To produce 125 cubic meters per hour of clean water, we will need to supply a higher quantity of water because of the presence of salts. We'll use the following formula to determine the feed water quantity:
F = (Q / (1 - R))
Where,
F = Feed Water Required
Q = Clean Water Required
R = % Recovery
We must first determine the % Recovery.
We can use the following formula to do so:
% Recovery = 100 - % Rejection
We are told that the TDS of the feed water is 3000 ppm and that the drinking water should have less than 700 ppm of TDS. As a result, the % Rejection can be calculated using the following formula:
% Rejection = (3000 - 700) / 3000 * 100
% Rejection = 76.67%
% Recovery = 100 - 76.67% = 23.33%
We can now calculate the Feed Water Required using the formula:
F = (125 / (1 - 0.2333))F = 162.76 cubic meters per hour
Therefore, 162.76 cubic meters per hour of feed water is required to produce 125 cubic meters per hour of clean water.
To know more about flow rate, click here
https://brainly.com/question/19863408
#SPJ11
Question 2 The Indigenous people perceive land as an economic asset to be exploited for economic gains. True False
Answers
Recognize and respect Indigenous perspectives on land, as they offer valuable insights into sustainable resource management and holistic approaches to development that prioritize the well-being of both people and the environment.
False. The statement that Indigenous people perceive land as an economic asset to be exploited for economic gains is not accurate and misrepresents the complex and diverse relationships that Indigenous communities have with their land. Indigenous perspectives on land are deeply rooted in cultural, spiritual, and ecological connections rather than solely economic considerations.
Indigenous peoples often view land as a sacred entity, an integral part of their identity, and a source of sustenance. Their relationship with the land is based on principles of stewardship, reciprocity, and harmony with nature. Traditional knowledge and practices passed down through generations emphasize sustainable resource management, biodiversity preservation, and the interconnectedness of all living beings.
While economic activities may be present within Indigenous communities, they are typically guided by principles of community well-being, self-sufficiency, and cultural preservation. Economic development is often pursued in ways that align with Indigenous values and prioritize the long-term health of the land and its inhabitants.
It is important to recognize and respect Indigenous perspectives on land, as they offer valuable insights into sustainable resource management and holistic approaches to development that prioritize the well-being of both people and the environment.
Learn more about valuable insights
https://brainly.com/question/27894163
#SPJ11
Let S be the upper half of the unit sphere x^2+y^2+z^2=1 and take n as the upper unit normal. Use Stoke's theorem to find ∬ S_[(∇×v)⋅n]dσ given v(x,y,z)=3z^2i+3xj−4y^3k. a) 3π b) −3π c)9π d)3/2π e) 6π
f) None of the above.
Answers
By using Stoke's theorem ∬ S [ (∇ × v) ⋅ n ] dσ is 6π. So, option e is the correct answer.
To apply Stoke's theorem and evaluate the surface integral, we need to calculate the curl of vector field v(x, y, z) and then find its dot product with the unit normal vector n.
Let's start by finding the curl of v(x, y, z):
∇ × v =
| i j k |
| ∂/∂x ∂/∂y ∂/∂z |
| 3z² 3x -4y³|
Applying the determinant expansion along the top row, we have:
∇ × v = (∂/∂y)(-4y³) - (∂/∂z)(3x) i
+ (∂/∂z)(3z²) - (∂/∂x)(-4y³) j
+ (∂/∂x)(3x) - (∂/∂y)(3z²) k
Simplifying, we get:
∇ × v = -12y² i + 3z² j + 3 k
Now, we need to find the dot product of ∇ × v with the unit normal vector n. Since the upper half of the unit sphere has positive z-component, the unit normal vector for this surface is n = (0, 0, 1).
Therefore, the dot product (∇ × v) ⋅ n simplifies to:
(-12y² i + 3z² j + 3 k) ⋅ (0, 0, 1)= 3
Now, we can evaluate the surface integral using Stoke's theorem:
∬ S [ (∇ × v) ⋅ n ] dσ = ∬ S (3) dσ
Since the surface S is the upper half of the unit sphere, the area element dσ can be written as dσ = r² sinθ dθ dφ, where r = 1 is the radius of the unit sphere, θ ranges from 0 to π/2, and φ ranges from 0 to 2π.
Therefore, the surface integral becomes:
∬ S (3) dσ = ∫∫ (3) r² sinθ dθ dφ
= 3 ∫[0 to 2π] ∫[0 to π/2] (1)² sinθ dθ dφ
= 3 ∫[0 to 2π] [-cosθ] [0 to π/2] dφ
= 3 ∫[0 to 2π] 1 dφ
= 3 (2π)
= 6π
Hence, the correct answer is e) 6π.
To know more about Stoke's theorem:
https://brainly.com/question/28381095
#SPJ11
A converging-diverging nozzle is designed to produce an exit flow of air at M = 4.0 and 1.0 atm. The stagnation temperature is 50°C. Calculate the upstream stagnation pressure. Calculate the throat area and mass flow for an exit area of 6.5 cm2.
Answers
A converging-diverging nozzle is an important component of a jet engine that is responsible for accelerating hot gases out of the back of the engine to produce thrust. The pressure, temperature, and velocity of the gases passing through the nozzle are controlled by the design of the nozzle.
The nozzle's design ensures that the gas flows at a high velocity and generates a lot of thrust. The following steps are used to calculate the upstream stagnation pressure: Given, Exit Mach Number (M) = 4.0, Exit Pressure (Pe) = 1.0 atm, Stagnation Temperature (T0) = 50°C1. Calculate the exit velocity using the isentropic relation for Mach number: Since M = 4.0, the exit velocity is:
[tex]V_e = M_e × c_e.[/tex]
Where c_e is the speed of sound at the exit.For air at 50°C, c_e = 1090 m/s. Therefore,V_e
[tex]4.0 × 1090 = 4360 m/s2.[/tex]
Calculate the pressure at the throat using the isentropic relation for Mach number:At the throat, M_t = 1.0 (by definition).Using the isentropic relation, we can calculate the pressure at the throat:P_t = P_e / [(1 + γ-1)/2]^(γ/γ-1)where γ = 1.4 (for air). Therefore, P_t = 1.0 / [(1 + 0.4)/2]^(1.4/0.4). P_t = 1.19 atm3.
Calculate the upstream stagnation pressure using the isentropic relation for stagnation pressure: Using the isentropic relation, we can calculate the upstream stagnation pressure:
[tex]P0 = Pe / [(1 + γ-1)/2]^(γ/γ-1) × [1 + (γ-1)/2 × Me^2]^(γ/γ-1)[/tex]
where Me is the Mach number at the exit (which is given as 4.0)Therefore[tex],P0 = 1.0 / [(1 + 0.4)/2]^(1.4/0.4) × [1 + (0.4/2) × 4^2]^(1.4/0.4)P0 = 10.68 atm.[/tex]
Therefore, the upstream stagnation pressure is 10.68 atm. The formula for mass flow is: [tex]dm/dt = ρ * A * V.[/tex]
Where, dm/dt is mass flow, ρ is density, A is the cross-sectional area of the flow, and V is the velocity of the flow. Therefore, the mass flow for an exit area of 6.5 cm² can be calculated using the following steps: Given, Exit Area (Ae) = 6.5 cm²Density (ρ) can be calculated using the ideal gas law :P = ρRTwhere P is the pressure, R is the gas constant, and T is the temperature.
Therefore, [tex]ρ = P / RT[/tex]
[tex](1.0 atm) / (287 J/kg-K × (50 + 273) K) = 0.382 kg/m³[/tex]
The velocity at the exit was calculated in step 1 as[tex]V_e = 4360 m/s.[/tex]
The cross-sectional area at the throat can be calculated using the isentropic relation for Mach number, which is :[tex]A_t = A_e / [(1/M_e) * ((2 / (γ+1)) * (1 + (γ-1)/2 * M_e^2))^((γ+1)/(2(γ-1)))].[/tex]
Therefore,[tex]A_t = 6.5 cm² / [(1/4) * ((2 / 1.4+1) * (1 + (0.4-1)/2 * 4^2))^((1.4+1)/(2(1.4-1)))][/tex]
[tex]A_t = 0.595 cm²[/tex]
The mass flow rate can now be calculated using the formula for mass flow:[tex]dm/dt = ρ * A_t * V_t = 0.382 kg/m³ × (0.595 cm² × 10^-4 m²/cm²) × 480 m/s dm/dt = 0.0115 kg/s.[/tex] Therefore, the mass flow rate is 0.0115 kg/s.
Therefore, the upstream stagnation pressure is 10.68 atm, and the mass flow rate is 0.0115 kg/s.
learn more about velocity visit:
brainly.com/question/30559316
#SPJ11
Cathy placed $6000 into a savings account. For how long can $900 be withdrawn from the account at the end of every month starting one month from now if it is 4.87% compounded monthly? The $900 can be withdrawn for ________months
Answers
$900 can be withdrawn from the account for approximately 35 months.
To determine how long $900 can be withdrawn from the savings account, we need to find the number of months it takes for the account balance to reach $900 after monthly compounding.
First, let's calculate the monthly interest rate. The annual interest rate is given as 4.87%. To convert it into a monthly interest rate, we divide it by 12 (months in a year).
Monthly interest rate = (4.87% / 100) / 12 = 0.04058
Next, we'll use the future value formula for compound interest:
[tex]FV = P * (1 + r)^n\\[/tex]
Where:
FV = Future Value (desired amount of $900)
P = Principal (initial deposit of $6000)
r = Monthly interest rate (0.04058)
n = Number of months
Now we can plug in the values and solve for n:
[tex]900 = 6000 * (1 + 0.04058)^nDivide both sides by 6000:0.15 = 1.04058^nTaking the natural logarithm (ln) of both sides:ln(0.15) = ln(1.04058^n)Using the logarithm properties (ln(a^b) = b * ln(a)):ln(0.15) = n * ln(1.04058)Now we can solve for n by dividing both sides by ln(1.04058):n = ln(0.15) / ln(1.04058)[/tex]
Using a calculator, we find:
n ≈ 34.85
Since we can't have a fraction of a month, we round up to the nearest whole number.
Therefore, $900 can be withdrawn from the account for approximately 35 months.
To know more about value click-
http://brainly.com/question/843074
#SPJ11
PLS HELP! I WILL MAKE U BRAINLIST! DUE TONIGHT!
USE DESMOS CALCULATOR
Answers
A sketch of the graph of each function is shown below.
If h > 1, the graph is translated to the right.
If h < 1, the graph is translated to the left.
What is a translation?In Mathematics and Geometry, the translation of a graph to the right simply means a digit would be added to the numerical value on the x-coordinate of the pre-image:
g(x) = f(x - N)
Where:
N is always greater than 1.
Conversely, the translation of a graph to the left simply means a digit would be subtracted from the numerical value on the x-coordinate of the pre-image:
g(x) = f(x + N)
Where:
N is always less than 1.
In conclusion, the graph of y = (x + h)² is translated to the right when h is greater than 1 while the graph of y = (x + h)² is translated to the left when h is less than 1.
Read more on function and translation here: brainly.com/question/31559256
#SPJ1
H. Elourine vs. chlorine Which one will have the higher electron affinity and why?
Answers
Overall, due to the combination of a higher effective nuclear charge and greater electron shielding, chlorine exhibits a higher electron affinity than fluorine.
Chlorine (Cl) will generally have a higher electron affinity compared to fluorine (F). Electron affinity is the energy change that occurs when an atom gains an electron in the gaseous state. Chlorine has a higher electron affinity than fluorine due to two main factors:
Effective Nuclear Charge: Chlorine has a larger atomic number and more protons in its nucleus compared to fluorine. The increased positive charge in the nucleus of chlorine attracts electrons more strongly, resulting in a higher electron affinity.
Electron Shielding: Chlorine has more electron shells compared to fluorine. The presence of inner electron shells in chlorine provides greater shielding or repulsion from the outer electrons, reducing the electron-electron repulsion and allowing the nucleus to exert a stronger attraction on an incoming electron.
To know more about electron affinity,
https://brainly.com/question/1542518
#SPJ11