The increased distance across the cell will result in an increase absorbance reading.
The concentration of [tex][Fescn]_2[/tex] would be affected if the cuvette had a 1.5 cm path length rather than the 1.0 cm value used.Since the absorbance of a sample is proportional to the concentration of a sample (as described by the Beer-Lambert law), increasing the path length of the cuvette would result in a decrease in absorbance. This means that the concentration of the sample would be lower than if the 1 cm path length was used. In other words, the concentration of [tex][Fescn]_2[/tex]would be lower if the cuvette had a 1.5 cm path length than if it had a 1.0 cm path length.
learn more about cuvette Refer:brainly.com/question/29385690
#SPJ1
a solution of cacl2 cacl 2 in water forms a mixture that is 31.5% 31.5 % calcium chloride by mass. if the total mass of the mixture is 195.4 g, 195.4 g, what masses of cacl2 cacl 2 and water were used?
The masses of calcium chloride (CaCl2) and water used to form the mixture are 61.18 g and 134.22 g, respectively.
The mass of calcium chloride (CaCl2):
The percentage of calcium chloride (CaCl2) in the mixture is 31.5%.
Multiply the total mass of the mixture (195.4 g) by 31.5% to find the mass of calcium chloride (CaCl2) in the mixture:
Mass of calcium chloride (CaCl2) = (195.4 g) x (31.5%) = 61.18 g
The mass of water:
Subtract the mass of calcium chloride (CaCl2) from the total mass of the mixture (195.4 g) to find the mass of water in the mixture:
Mass of water = (195.4 g) - (61.18 g) = 134.22 g
Therefore, masses of calcium chloride (CaCl2) and water used to form the mixture are 61.18 g and 134.22 g, respectively.
to know more about calcium chloride refer here:
https://brainly.com/question/15296925#
#SPJ11
a mixture of three gases has a total pressure of 1,380 mmhg at 298 k. the mixture is analyzed and is found to contain 1.27 mol co2, 3.04 mol co, and 1.50 mol ar. what is the partial pressure of ar? multiple choice 0.258 atm 301 mmhg 356 mmhg 5,345 mmhg 8,020 mmhg
The partial pressure of Ar is 0.219 * 1,380 mmHg = 301 mmHg.
The partial pressure of a gas in a mixture is equal to the mole fraction of that gas times the total pressure of the mixture.
The mole fraction of Ar in this mixture is 1.50/6.81 = 0.219. Thus, the partial pressure of Ar is 0.219 * 1,380 mmHg = 301 mmHg.
The ideal gas law states that the pressure of a gas is directly proportional to its number of moles and inversely proportional to its volume.
This law is expressed in the equation PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature.
In a mixture of gases, each gas behaves independently according to the ideal gas law. Thus, the total pressure of the mixture is the sum of the partial pressures of each gas.
The partial pressure of a gas is equal to its mole fraction times the total pressure. The mole fraction of a gas is the number of moles of that gas divided by the total number of moles of all gases in the mixture.
In the example provided, the total pressure of the mixture is 1,380 mmHg, the number of moles of CO2 is 1.27, the number of moles of CO is 3.04, and the number of moles of Ar is 1.50.
The total number of moles of all gases in the mixture is 1.27 + 3.04 + 1.50 = 6.81. The mole fraction of Ar is 1.50/6.81 = 0.219. Thus, the partial pressure of Ar is 0.219 * 1,380 mmHg = 301 mmHg.
To know more about partial pressure refer here:
https://brainly.com/question/13199169#
#SPJ11
what volume of 0.0500 m sodium hydroxide should be added to 250 ml of 0.100 m hcooh to obtain a solution with a ph of 4.50
The required volume of 0.0500 M sodium hydroxide that should be added to 250 ml of 0.100 M HCOOH to obtain a solution with a pH of 4.50 is: 10.5 ml.
To solve this problem, we can use the equation for the reaction between HCOOH and NaOH. The balanced chemical equation is: HCOOH + NaOH → HCOONa + H₂O
From this, we can see that one mole of HCOOH reacts with one mole of NaOH to form one mole of HCOONa and one mole of water. We can also write the equation for the ionization of HCOOH: HCOOH + H₂O ⇌ H₃O+ + HCOO-
At pH = 4.50, the concentration of hydronium ions is 3.16 x 10⁻⁵ M. Using this value, we can solve for the concentration of formate ions:
[H₃O+] = [HCOO-]Ka = [H₃O+][HCOO-]/[HCOOH]
Substituting the values gives: Ka = (3.16 x 10⁻⁵)2 / (0.100 - x)x = 0.00227 M
where x is the amount of HCOOH that reacts with NaOH.
Substituting the values gives:
(0.00227)(V1) = (0.100)(0.250 - x)V1 = (0.100)(0.250 - x) / 0.00227V1 = 10.5 - 4.63x
The pH of the solution is given as 4.50. This means that the concentration of hydronium ions is 3.16 x 10⁻⁵5 M. Using this value, we can solve for the concentration of formate ions:
[H₃O+] = [HCOO-]Ka = [H₃O+][HCOO-]/[HCOOH]
Since one mole of HCOOH reacts with one mole of NaOH, the amount of NaOH that is required to react with x moles of HCOOH is also x moles. Therefore, the concentration of NaOH that is required is also 0.00227 M. The volume of NaOH that is required can be calculated using the following equation: M1V1 = M2V2
where M1 is the concentration of NaOH, V1 is the volume of NaOH, M2 is the concentration of HCOOH, and V2 is the volume of HCOOH.
Substituting the values gives[tex](0.00227)(V1) = (0.100)(0.250 - x)V1 = (0.100)(0.250 - x) / 0.00227V1 = 10.5 - 4.63x[/tex]
Since x = 0.00227 M, V1 can be calculated as: [tex]V1 = 10.5 - (4.63)(0.00227) = 10.5 - 0.0105 = 10.5 mL[/tex]
Therefore, the volume of 0.0500 M sodium hydroxide that should be added to 250 mL of 0.100 M HCOOH to obtain a solution with a pH of 4.50 is 10.5 mL.
To know more about sodium hydroxide refer here:
https://brainly.com/question/29327783#
#SPJ11
when 0.2 moles of hydrofluoric acid are added to 100 ml of water, the resulting solution has a ph equal to 4. what is the percent dissociation of hf?
The percent dissociation of HF is 144%. This result may seem greater than 100%, but it is possible for the percent dissociation to exceed 100% in cases where the concentration of the dissociated species exceeds the initial concentration of the undissociated species.
What is Percent Dissociation?
Percent dissociation is a measure of the extent to which a substance dissociates in a solution. It is defined as the ratio of the concentration of the dissociated species to the initial concentration of the substance, expressed as a percentage.
The first step in solving this problem is to write the equation for the dissociation of hydrofluoric acid (HF) in water:
HF + H2O ⇌ H3O+ + F-
Ka = [H3O+][F-] / [HF]
Since the pH of the solution is given as 4, we know that:
[H3O+] = 10^-4 M
We can use the given initial concentration of HF and the expression for Ka to solve for the concentration of F- at equilibrium. Since HF is a weak acid, we can assume that the dissociation is small compared to the initial concentration, so we can use the approximation [HF] ≈ [HF]0.
Ka = [H3O+][F-] / [HF]0
[F-] = Ka [HF]0 / [H3O+]
[F-] = (7.2 × 10^-4)(0.2 mol / 0.1 L) / (10^-4 M)
[F-] ≈ 0.288 M
The percent dissociation of HF is defined as:
% dissociation = ([F-] / [HF]0) × 100%
% dissociation = (0.288 M / 0.2 mol / 0.1 L) × 100%
% dissociation = 144%
Learn more about Percent Dissociation from given link
https://brainly.com/question/30445997
#SPJ1
what is the conjugate base of ch3nh3 ? group of answer choices ch3nh2 ch3nh3 ch3nh3- ch3nh2- ch3nh2
The conjugate base of CH₃NH₃ is CH₃NH₂⁻.
The conjugate base is the species that is formed when an acid donates a proton (H+). In this case, CH₃NH₃ is acid, and CH₃NH₂⁻ is its conjugate base. CH₃NH₂⁻ is formed when the acid CH₃NH₃ donates a proton to another molecule.
To understand how CH₃NH₃donates a proton to become CH₃NH₂⁻ , it is important to first understand the acid-base reaction. An acid-base reaction is a reaction where an acid donates a proton to a base, forming salt and water. In this case, CH₃NH₃ donates a proton to the base, forming CH₃NH₂⁻ and a water molecule. The equation for this reaction is as follows:
CH₃NH₃ + Base --> CH₃NH₂⁻ + Salt + H₂O
It is important to note that in this reaction, the base is not specifically stated as it can be any molecule capable of accepting a proton.
To summarize, the conjugate base of CH₃NH₃ is CH₃NH₂⁻ . This species is formed when the acid CH₃NH₃ donates a proton to a base, forming salt and water.
To know more about conjugate bases, refer here:
https://brainly.com/question/30225100#
#SPJ4
the decomposition of a generic diatomic element in its standard state is represented by the equation
The decomposition of a generic diatomic element in its standard state is represented by the equation [tex]X_{2}[/tex] → 2X, where X represents the diatomic element.
The given equation for the decomposition of a generic diatomic element in its standard state is: [tex]M_{2}[/tex](g)→2M(g).
Explanation: In the given equation, the diatomic element M2 dissociates to form two monatomic atoms of M gas, which is its standard state. The reaction is therefore an example of a decomposition reaction, where a compound is broken down into simpler substances.
The standard state of a substance is the most stable form of the element at a pressure of 1 atm and a temperature of 298 K. For diatomic elements like M2, the standard state is a gas phase where the atoms are in their most stable form as monoatomic atoms, rather than as molecules.
For more questions related to decomposition.
https://brainly.com/question/8009068
#SPJ11
The girl was measuring the hallway the first part was 132 inches long the second part was 3 yards long how long is the Hallway in feet?? I don't know the answer it is on my homework and I have to finish it up so I won't fail please help
The length of the hallway is 20 feet. To calculate the length of the hallway in feet, we need to first convert the measurements to the same unit of measurement. Let's convert the second part from yards to inches, since the first part is already in inches:
3 yards = 3 x 36 inches = 108 inches
Now we can add the two lengths together:
Total length = 132 inches + 108 inches = 240 inches
Finally, we can convert the total length from inches to feet by dividing by 12:
Total length = 240 inches ÷ 12 = 20 feet
Therefore, the length of the hallway is 20 feet.
Learn more about hallway
https://brainly.com/question/16400635
#SPJ4
Full Question ;
The girl was measuring the hallway the first part was 132 inches long the second part was 3 yards long how long is the Hallway in feet??
calculate the ka based on the following information for the following unknown acid, ha. the ph of a buffer system is 4.219. the buffer is composed of 2.43 moles of ha and 1.75 moles of naa dissolved into 1.92 l of solution.
Based on the given information about the acid, the acid dissociation constant, Ka of the unknown acid is 4.97 x 10⁻⁷.
What is the acid dissociation constant, Ka of the acid?To calculate the Ka of the unknown acid, we can use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
where:
pH = 4.219 (given)
[A-] = concentration of the conjugate base (NaA)
[HA] = concentration of the acid (HA)
We can find the concentration of NaA and HA using the given information:
moles of HA = 2.43 mol
moles of NaA = 1.75 mol
total moles = 2.43 + 1.75
total moles = 4.18 mol
volume of solution = 1.92 L
[H+] = 10^(-pH)
[H+] = 6.87 x 10^(-5) M
[HA] = (moles of HA) / (volume of solution)
HA = 1.264 M
[NaA] = (moles of NaA) / (volume of solution) = 0.911 M
Using the equation for the dissociation of the acid:
HA + H2O ⇌ H3O+ + A-
Ka = ([H3O+][A-]) / [HA]
We can assume that the concentration of H3O+ is equal to the concentration of NaA, since the pH is closer to the pKa of the acid. Therefore:
Ka = ([NaA][H+]) / [HA]
Ka = [(0.911 M)(6.87 x 10^(-5) M)] / (1.264 M)
Ka = 4.97 x 10^(-7)
Learn more about acid dissociation constant, Ka at: https://brainly.com/question/9396848
#SPJ1
what is the force magnitude (in nn) between a positive sodium ion and a negative chloride ion in an ionic nacl crystal if the are 0.5 nm apart?
The force magnitude between a positive sodium ion and a negative chloride ion in an ionic NaCl crystal is 4.47 x 10^-8 N (Newtons). This force is due to electrostatic attraction between the two ions.
The electrostatic potential energy of the system. This is done using the equation U = kqQ/r,
where k is the Coulomb's constant (8.99 x 10^9 Nm^2/C^2), q is the charge of the sodium ion (+1.6 x 10^-19 C), Q is the charge of the chloride ion (-1.6 x 10^-19 C), and r is the distance between them (0.5 nm).
U = 8.99 x 10^9 x 1.6 x 10^-19 x (-1.6 x 10^-19) / 0.5 x 10^-9, which simplifies to 4.47 x 10^-8 N.
The electrostatic potential energy is a measure of the work done in bringing two charges together, and is also equal to the magnitude of the electrostatic force.
Therefore, the force magnitude between the two ions is 4.47 x 10^-8 N.
The electrostatic force between the two ions acts along the line joining them, pushing the positive sodium ion towards the negative chloride ion.
The magnitude of this force is attractive, as the two ions have opposite charges, and is 4.47 x 10^-8 N, as calculated above.
This electrostatic force is strong enough to hold the ions together in the ionic crystal lattice of NaCl.
to know more about electrostatic refer here:
https://brainly.com/question/31042490#
#SPJ11
Which one of the following compounds is not a product of reaction between 1,3-butadiene and HBr? Select one a. (S)-3-bromo-1-butene b. (R)-3-bromo-1-butene c. (E)-1-bromo-2-butene d. (Z)-1-bromo-2-butene e. (Z)-2-bromo-2-butene
The correct option is E. The compound that is not a product of the reaction between 1,3-butadiene and HBr is (Z)-2-bromo-2-butene.
A chemical reaction is a process in which one or more substances (reactants) are transformed into new substances (products) by breaking and forming chemical bonds. Chemical reactions are essential in many natural and synthetic processes, including the formation of the molecules that make up living organisms and the production of materials such as medicines, fuels, and plastics.
Chemical reactions involve the rearrangement of atoms, ions, or molecules, resulting in the formation of new substances with different properties from those of the reactants. The reactants and products of a chemical reaction can be represented by a chemical equation, which shows the identities and quantities of the reactants and products.
To learn more about Reaction visit here:
brainly.com/question/17434463
#SPJ4
a pure titanium cube has an edge length 2.77 in. how many titanium atoms does i contain? titanium does have a density of 4.50 g/cm^3
The question asks, "How many titanium atoms does a pure titanium cube with an edge length of 2.77 inches contain?"
Given that titanium has a density of 4.50 g/cm^3, thus the number of titanium atoms present in the cube is 2.44 x 1024 atoms.
We can calculate the answer by using the following formula: Atoms = Volume x (Atomic Mass / Molecular Mass)
Step 1: Calculate the volume of the cube: Volume = (Edge Length)3 = (2.77 in)3 = 24.4 in3
Step 2: Calculate the number of atoms: Atoms = 24.4 in3 x (47.867/47.867) = 24.4 in3
Therefore, the pure titanium cube with an edge length of 2.77 inches contains 24.4 in3 of titanium atoms.
Read more about volume:
https://brainly.com/question/463363
#SPJ11
the mixing of which pair of reactants will result in a precipitation reaction?23)a)k2so4(aq) hg2(no3)2(aq)b)hcl(aq) ca(oh)2(aq)c)csi(aq) naoh(aq)d)nano3(aq) nh4cl(aq)
The mixing pair of reactants will result in a precipitation reaction are:a) K2SO4(aq) and Hg2(NO3)2(aq)The reaction can be represented as:K2SO4(aq) + Hg2(NO3)2(aq) → 2KNO3(aq) + Hg2SO4(s)
Precipitation reactions occur when cations and anions come together to form an insoluble ionic compound or salt, also known as a precipitate, that settles out of the solution because it is not water-soluble.The process involves two solutions containing soluble salts that combine and form an insoluble compound that appears as a solid, called a precipitate, which settles at the bottom of the container.
Precipitation reactions can occur when an insoluble substance, such as a salt or a solid, is produced as a result of combining two or more solutions with specific ions. It is necessary to mix two solutions that contain ions that will react and produce an insoluble compound or a precipitate.For example, K2SO4(aq) + Hg2(NO3)2(aq) → 2KNO3(aq) + Hg2SO4(s)This equation represents a precipitation reaction because Hg2SO4(s), an insoluble solid, forms when K2SO4(aq) and Hg2(NO3)2(aq) are combined.
Learn more about precipitation reactions at:
https://brainly.com/question/29762381
#SPJ11
which of following statement does not describe the saturated liquid if heat is added to it? multiple choice question. it's about to condense. it is about to vaporize. it refers to a point on a t-v diagram. it's still considered a liquid. any heat added will cause some of the liquid to vaporize.
It is about to vaporize does not describe the saturated liquid if heat is added to it. Here option B is the correct answer.
A saturated liquid is a liquid that is in equilibrium with its vapor at a given temperature and pressure. If heat is added to a saturated liquid, its temperature will increase while its pressure remains constant until it reaches the saturation temperature. At this point, the saturated liquid will start to vaporize or boil, and the temperature will remain constant until all of the liquid has been converted to vapor.
Option A - "it's about to condense" - is true for a saturated vapor if heat is removed from it. Option C - "it refers to a point on a t-v diagram" - is also true since a saturated liquid corresponds to a point on the liquid-vapor saturation line on a temperature-volume (t-v) diagram.
Option D - "it's still considered a liquid" - is true since the saturated liquid is still in the liquid state even though it is about to vaporize. Option E - "any heat added will cause some of the liquid to vaporize" - is true since any additional heat added to a saturated liquid will cause it to vaporize or boil at a constant temperature and pressure.
To learn more about saturated liquid
https://brainly.com/question/17164330
#SPJ4
Complete question:
Which of the following statement does not describe the saturated liquid if heat is added to it? multiple choice questions.
A - it's about to condense.
B - it is about to vaporize.
C - it refers to a point on a t-v diagram.
D - it's still considered a liquid.
E - any heat added will cause some of the liquid to vaporize.
calculate the number of vacancies per m^3 for gold at 900 c. the energy for vacancy formation is 0.86 ev/atom
At 900°C, the number of vacancies per m^3 for gold is 1.32 x 10^17 vacancies per m^3.
The number of vacancies per m^3 for gold at 900°C, the energy for vacancy formation (0.86 eV/atom) must be known.
Vacancies are atoms that are missing from the crystal lattice, so we must use the energy of vacancy formation to calculate how many vacancies can exist at a given temperature.
At 900°C, the energy of vacancy formation is 0.86 eV/atom. This energy is equal to 8.6 x 10^-19 Joules. The number of vacancies per m^3,
Number of vacancies = (Energy of vacancy formation / Boltzmann's Constant x Temperature) / Atom's Volume
Number of vacancies = (8.6 x 10^-19 / 1.38 x 10^-23 x 900) / 4.20 x 10^-29
Number of vacancies = 1.32 x 10^17 vacancies per m^3
Therefore, at 900°C, the number of vacancies per m^3 for gold is 1.32 x 10^17 vacancies per m^3.
It's important to note that this number is temperature dependent; if the temperature of the gold is increased or decreased, the number of vacancies per m^3 will also change.
As temperature increases, the number of vacancies per m^3 will increase and vice versa.
to know more about vacancies refer here:
https://brainly.com/question/12598037#
#SPJ11
an unknown gas effuses at a rate 0.667 times the rate of no. what is the molar mass of the unknown gas?
Answer:
The molar mass of the unknown gas is:
Munknown = (28 g/mol)2 / 0.667 = 83.6 g/mol
The molar mass of the unknown gas can be determined by the Graham's Law of Effusion. According to this law, the rate of effusion of a gas is inversely proportional to the square root of its molar mass.
Thus, if the rate of effusion of the unknown gas is 0.667 times that of Nitrogen (N2), then its molar mass can be calculated as:
Munknown = (MN2)2 / 0.667
Where, MN2 is the molar mass of Nitrogen (28 g/mol).
Therefore, the molar mass of the unknown gas is:
Munknown = (28 g/mol)2 / 0.667 = 83.6 g/mol
Learn more about Graham's Law of Effusion here:
https://brainly.com/question/22359712#
#SPJ11
if the percent of solute in an aqueous solution is 5%, what is the percentage of water in that solution?
Answer: The percentage of water in the solution would be 95%.
Explanation:
The percent composition of a solution refers to the amount of each component in the solution as a percentage of the total solution. In this case, if the percent of solute in the solution is 5%, then the remaining percentage must be the percent of water in the solution.
Since the total percent composition of the solution must add up to 100%, we can find the percent of water in the solution by subtracting the percent of solute from 100%.
% Water = 100% - % Solute
% Water = 100% - 5%
% Water = 95%
Therefore, the percentage of water in the solution is 95%.
how long will it take the same amount of gaseous xe to effuse from the same container under identical conditions?
The time taken by the same amount of gaseous Xe to effuse from the same container under identical conditions will be inversely proportional to the square root of its molar mass.
How long will it take for the same amount of gaseous Xe to effuse from the same container under identical conditions? According to Graham's law of effusion, the rate of effusion of a gas is inversely proportional to the square root of its molar mass, i.e. the heavier the gas, the slower the effusion rate. The effusion rate of two gases, A and B, can be related to their molar masses, MA and MB, as follows:
RA/RB = √MB/MA
where RA is the rate of effusion of gas A, and RB is the rate of effusion of gas B. The ratio of the rates of effusion is the same as the ratio of the molecular speeds. Therefore, the time required by gases A and B to effuse from a container under identical conditions is also inversely proportional to the square root of their molar masses.TA/TB = √MA/MBwhere TA is the time required for gas A to effuse, and TB is the time required for gas B to effuse.
Learn more about effusion at brainly.com/question/28320456
#SPJ11
a 100.0 ml sample of 0.18 m hclo4 is titrated with 0.27 m lioh. the equivalence points is reached after 66.67 ml of lioh have been added. determine the ph of the solution at the equivalence point.
The pH of the solution at the equivalence point is 7. (after titration).
Equivalence point in a titration: When titrating an acid and a base, the equivalence point is the point where the stoichiometric amounts of the acid and base have reacted. This means that all the acid present in the solution has been neutralized by the base. Likewise, all the base present in the solution has been neutralized by the acid.The pH at the equivalence point: The pH at the equivalence point depends on the nature of the acid and the base. For example, if a strong acid and a strong base are titrated, the pH at the equivalence point is 7.00. On the other hand, if a strong acid and a weak base are titrated, the pH at the equivalence point is less than 7.00. Similarly, if a weak acid and a strong base are titrated, the pH at the equivalence point is greater than 7.00. The pH at the equivalence point can be determined using a few formulas. To determine the pH of the solution at the equivalence point when a 100.0 mL sample of 0.18 M HClO4 is titrated with 0.27 M LiOH,
Steps: 1. Calculate the moles of HClO4 and LiOH at the equivalence point: Moles of HClO4 = volume (L) x concentration (M) = 0.1 L x 0.18 mol/L = 0.018 mol. Moles of LiOH = volume (L) x concentration (M) = 0.06667 L x 0.27 mol/L = 0.018 mol
Step: 2. Since the moles of HClO4 and LiOH are equal at the equivalence point, the reaction between them is complete. The product of the reaction is water and a salt (LiClO4). The salt will not affect the pH, as Li+ and ClO4- ions do not hydrolyze in water.
Step: 3. At the equivalence point, the pH is determined by the concentration of H2O. Since water's pH is 7 at 25°C, the pH of the solution at the equivalence point is 7. (after titration).
Learn more about equivalent point and titration here, https://brainly.com/question/23502649
#SPJ11
How many grams of aluminum sulfate would be formed if 3.52 grams of aluminum completely reacted with H2SO4?
2Al + 3H2SO4 ---------------------> Al2(SO4)3 + 3H2
Taking into account the reaction stoichiometry, 22.29 grams of Al₂(SO₄)₃ are formed if 3.52 grams of aluminum completely reacted with H₂SO₄.
Reaction stoichiometryThe balanced reaction is:
2 Al + 3 H₂SO₄ → Al₂(SO₄)₃ + 3 H₂
By reaction stoichiometry (that is, the relationship between the amount of reagents and products in a chemical reaction), the following amounts of moles of each compound participate in the reaction:
Al: 2 molesH₂SO₄: 3 molesAl₂(SO₄)₃: 1 molH₂: 3 molesThe molar mass of the compounds is:
Al: 27 g/moleH₂SO₄: 98 g/moleAl₂(SO₄)₃: 342 g/moleH₂: 2 g/moleBy reaction stoichiometry, the following mass quantities of each compound participate in the reaction:
Al: 2 moles ×27 g/mole= 54 gramsH₂SO₄: 3 moles ×98 g/mole= 294 gramsAl₂(SO₄)₃: 1 mol ×342 g/mole= 342 gramsH₂: 3 moles ×2 g/mole= 6 gramsMass of Al₂(SO₄)₃ formedThe following rule of three can be applied: if by reaction stoichiometry 54 grams of Al form 342 grams of Al₂(SO₄)₃, 3.52 grams of Al form how much mass of Al₂(SO₄)₃?
mass of Al₂(SO₄)₃= (3.52 grams of Al× 342 grams of Al₂(SO₄)₃)÷ 54 grams of Al
mass of Al₂(SO₄)₃= 22.29 grams
Finally, 22.29 grams of Al₂(SO₄)₃ are formed.
Learn more about the reaction stoichiometry:
brainly.com/question/24741074
#SPJ1
a certain reaction has an activation energy of 34.34 kj/mol. 34.34 kj / mol. at what kelvin temperature will the reaction proceed 3.00 3.00 times faster than it did at 357 k?
The reaction will proceed 3 times faster than it did at 357 k at a temperature of 828 K.
The Arrhenius equation describes the effect of temperature on reaction rate. It is given by:
k = Ae^(-Ea/RT)
where k is the rate constant, A is the pre-exponential factor, Ea is the activation energy, R is the gas constant, and T is the temperature in Kelvin.
Rearranging this equation, we have ln(k) = ln(A) - (Ea/RT).
A certain reaction has an activation energy of 34.34 kJ/mol. At 357 K, the rate constant for the reaction is k1. When the reaction is 3 times faster, the rate constant will be 3k1.
Substituting these values in the Arrhenius equation, we have:
ln(3k1) = ln(A) - (34.34 kJ/mol)/(R*T)
ln(k1) = ln(A) - (34.34 kJ/mol)/(R*357 K)
Subtracting these two equations, we obtain:
ln(3) = (34.34 kJ/mol)/(R*k1*T)
Solving for T, we have:
T = (34.34 kJ/mol)/(R*k1*ln(3))
Putting the given values, we get:
T = (34.34 kJ/mol)/(8.314 J/K*mol*3.00*ln(3))
T = 828 K
Therefore, the reaction will proceed 3.00 times faster at 828 K compared to 357 K.
Learn more about Arrhenius equation here: https://brainly.com/question/13467424.
#SPJ11
a mineral contains 675 parent atoms and 225 daughter atoms. if the half life for the radioactive element is 40 million years, how old is the rock?
A mineral contains 675 parent atoms and 225 daughter atoms and the half-life for the radioactive element is 40 million years, the age of the rock is: approximately 46.8 million years
The half-life of the radioactive substance is 40 million years. The number of parent atoms is 675 and the number of daughter atoms is 225. To calculate the age of the rock, we must first calculate the number of half-lives. The number of daughter atoms increases as time passes, while the number of parent atoms decreases.
After each half-life, the number of parent atoms decreases by 50%, and the number of daughter atoms increases by 50%. For example, after one half-life, 337.5 parent atoms remain, and 562.5 daughter atoms have been produced. The rock's age can be determined by determining how many half-lives have elapsed. In order to calculate the number of half-lives, the following equation is used:
The number of parent atoms remaining = the original number of parent atoms × (1/2)number of half-lives
Since the initial number of parent atoms is 675, we have:
[tex]225 = 675 × (1/2)number of half-lives[/tex]
Solving for the number of half-lives, we get:
[tex]number of half-lives = log(225/675) ÷ log(1/2) ≈ 1.17[/tex]
Since one half-life is 40 million years, the age of the rock is:
Age = number of half-lives × half-life
Age = 1.17 × 40 million years = 46.8 million years
Therefore, the age of the rock is approximately 46.8 million years.
To know more about radioactive refer here:
https://brainly.com/question/1770619#
#SPJ11
how many calcium ions can bind to one edta molecule. in other words, what is the mole ratio? group of answer choices 2 : 1 1 : 2 1 : 1 1 : 3
The mole ratio of calcium ions to EDTA molecules is 1:1.
EDTA (ethylene diamine tetraacetic acid) is a molecule composed of two nitrogen atoms, two oxygen atoms, four acetate (CH₃COO⁻) groups, and two ethylene (CH₂CH₂) groups.
It binds to cations, particularly divalent cations like calcium ions (Ca2+). Each EDTA molecule binds to one calcium ion, forming an octahedral complex.
The process of binding is a result of the EDTA molecule's geometry and the ionic nature of the calcium cation.
The four acetate groups of EDTA are arranged in a square planar structure, while the two nitrogen atoms and the two ethylene groups form a loop on the upper side of the molecule.
When the EDTA molecule is exposed to calcium ions in an aqueous solution, the calcium cation binds to the nitrogen atoms and the ethylene groups, forming a six-membered ring.
This complex is referred to as an EDTA–Ca2+ octahedral complex.
The 1:1 mole ratio of EDTA and calcium ions is important for understanding the chemistry of EDTA, as well as for applications such as buffering and sequestering.
Buffering solutions help maintain a stable pH level, and sequestering solutions are used to bind and remove metal ions from a solution. The 1:1 ratio of EDTA to calcium ions is essential for both of these applications.
The mole ratio of calcium ions to EDTA molecules is 1:1. This ratio is necessary for understanding the chemistry of EDTA, as well as for applications such as buffering and sequestering.
to know more about mole ratio refer here:
https://brainly.com/question/15288923#
#SPJ11
1.
2.
Grams of solute
3.
4.
0600
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
NH37
Solubility Curve
KCIÓ3
FONX
NHẠC
O
0 10 20 30 40 50
KCI
Naci
Ce2(SO4)3
60 70 80 90 100
Temperature (°C)
How many grams of ammonium chloride (NH4Cl) is dissolved at 50°C?
Which compound is least soluble in water at 10°C?
How many grams of KNO3 can be dissolved at 50°C?
Are the following solutions unsaturated, saturated, or supersaturated?
a.
45g of NaNO3 in 100 g of water at 30°C.
b. 60g of KClO3 in 100 g of water at 60°C.
5. How many grams of NaNO3 are required to saturate 100 grams of water at
75°C?
6. At what temperature would 25g of potassium chlorate (KClO3) dissolve?
7. 89 g NaNO3 is prepared at 30°C.
From the solubility curve:
37 grams of NH₄Cl can be dissolved at 50°C.Sodium chloride (NaCl) is the least soluble compound40 grams of KNO₃ a. unsaturated, b. supersaturated.100 grams 45°CHow to determine saturation and temperature?According to the solubility curve for KNO₃, approximately 40 grams of KNO₃ can be dissolved at 50°C.
a. Since 45g of NaNO₃ in 100 g of water at 30°C is below the saturation point, the solution is unsaturated.
b. Since 60g of KClO3 in 100 g of water at 60°C is above the saturation point, the solution is supersaturated.
To determine how many grams of NaNO₃ are required to saturate 100 grams of water at 75°C, we need to look at the solubility curve for NaNO₃. At 75°C, approximately 75 grams of NaNO₃ can be dissolved in 100 grams of water. Therefore, to saturate 100 grams of water, we would need to add 75 grams of NaNO₃.
To find the temperature at which 25g of KClO₃ dissolves, we need to look at the solubility curve for KClO₃. At 25g, the curve intersects the solubility line at approximately 45°C, so 25g of KClO₃ would dissolve at 45°C.
Learn more on saturation point here: https://brainly.com/question/23866986
#SPJ1
which statement is true a-in a reaction, oxidation can occur independently of reduction b-a redox reaction involves either the transfer of an electron or a change in oxidation state of an element c-if any of the reactants or products in a reaction contain oxygen the reaction is a redox reaction d- the reducing agent reduces another substance and is itself oxidized
The correct statement is option B - A redox reaction involves either the transfer of an electron or a change in oxidation state of an element.Redox reactions involve the transfer of electrons from one substance to another.
The term "redox" refers to the simultaneous oxidation and reduction of molecules in the reaction, with one molecule losing electrons and the other gaining electrons.
Redox reactions is:Oxidation: Loss of electronsReduction: Gain of electrons. A molecule or atom that loses electrons is said to be oxidized, while one that gains electrons is said to be reduced.
The oxidized substance is an oxidizing agent, while the reduced substance is a reducing agent.
The statement "A redox reaction involves either the transfer of an electron or a change in oxidation state of an element" is true as the redox reaction involves both reduction and oxidation reactions.
Any substance that is oxidized should be reduced by another substance, and vice versa. Thus, a redox reaction involves the transfer of electrons from one substance to another.
Although oxygen is often present in redox reactions, it is not a necessary component of them. So, the statement C is false, and oxidation can not occur independently of reduction, so the statement A is false too.
The reducing agent reduces another substance and is itself oxidized; thus, statement D is also true.
to know more about redox reaction refer here:
https://brainly.com/question/13293425#
#SPJ11
presented with two tubes: one tube with a buffered solution + acid and one tube with water + acid, how will you know which tube has the buffer and which tube does not have the buffer?
One tube has a buffered solution + acid and the other tube has water + acid. To decide whether or not the solution is buffered, a simple pH test can be done. An acid-base indicator can be used to determine the pH of each solution.
A buffered solution is defined as a solution that can withstand minor changes in pH upon the addition of small amounts of an acid or base.
Consider the following steps:
To both tubes, add a small amount of acid-base indicator. Determine the pH of each solution by observing the color change of the acid-base indicator when it is added to it. The pH of the solution is determined by the color of the acid-base indicator after it has been added to it. Compare the pH of the two solutions. The solution with the lower pH is likely to have a buffer, whereas the solution with the higher pH is unlikely to have a buffer. This is due to the fact that the addition of an acid to a buffered solution would result in a lower pH, whereas the addition of an acid to an unbuffered solution would result in a higher pH. To find out which tube has the buffer and which does not, one has to compare the pH of each solution.Learn more about buffer: https://brainly.com/question/9458699
#SPJ11
All atoms of the same element have exactly the same what?
why does the procedure use a graduated cylinder and not simply have you put 2 ml of solution directly into the test tube?
A graduated cylinder is necessary to ensure accurate and precise measurements.
The use of a graduated cylinder to measure 2 ml of the solution instead of pouring the solution directly into the test tube is necessary to ensure accurate and precise measurements. Graduated cylinders are calibrated instruments that have markings indicating the volume of liquid inside them.
This allows for a more precise measurement of the solution than simply eyeballing it and pouring it into the test tube.
Additionally, a graduated cylinder reduces the risk of spills, which can lead to inaccurate measurements and waste of resources. Furthermore, it allows for consistent measurements every time the experiment is repeated.
In conclusion, the use of a graduated cylinder is essential when measuring 2 ml of solution for a lab experiment. It allows for accurate, precise, and consistent measurements, and also reduces the risk of spills and waste of resources.
Therefore, the use of a graduated cylinder to measure 2 ml of the solution instead of pouring the solution directly into the test tube is necessary to ensure accurate and precise measurements and reduce the risk of spills and waste of resources.
To know more about the graduated cylinders, refer here:
https://brainly.com/question/18948497#
#SPJ11
how many moles of o2 will be released if a liter of blood containing 45 g of hemoglobin is transferred from 60 torr, ph 7.6 to 20 torr, ph 7.2? hemoglobin has a molecular weight of 68,000.
Answer: Approximately 0.00033 moles of oxygen will be released from one liter of blood containing 45 grams of hemoglobin when it is transferred from 60 torr, pH 7.6, to 20 torr, pH 7.2.
First of all, the amount of hemoglobin in the given amount of blood has to be determined using the given data: Amount of hemoglobin in 1 L of blood = 45 g, Hemoglobin's molecular weight is 68,000 g/mol. : Number of moles of hemoglobin = 45/68000 = 0.000662 moles. After that, use the fact that the partial pressure of oxygen is related to the amount of dissolved oxygen, given the oxygen-hemoglobin equilibrium equation.
The formula for dissolved oxygen can be expressed as: Dissolved O2 = PO2 x solubility of O2PO2 = Partial pressure of oxygen in blood = 60 torr (initial) and 20 torr (final). Solubility of oxygen in blood can be determined from the table, which gives solubility as 0.0031 mol/L torr at 37°C.
The calculation of dissolved oxygen under initial and final conditions is as follows:Initial dissolved oxygen = 60 torr × 0.0031 mol/L torr = 0.186 mol/L Final dissolved oxygen = 20 torr × 0.0031 mol/L torr = 0.062 mol/L Thus, the amount of dissolved oxygen that has been released is the difference between the initial and final dissolved oxygen:Amount of dissolved oxygen released = initial dissolved oxygen - final dissolved oxygen= 0.186 - 0.062 = 0.124 mol/L
Amount of oxygen released = number of moles of hemoglobin × 4 × 0.124= 0.000662 × 4 × 0.124= 0.00033 moles
Know more about hemoglobin here:
https://brainly.com/question/15011428
#SPJ11
which is true about the rate-limiting step in a reaction? select all that apply: it is the slowest step. it limits (or determines) the rate of the reaction. it does not influence the rate law. it is always the first step. g
The true statements about the rate-limiting step in a reaction are it is the slowest step and it limits (or determines) the rate of the reaction. Therefore, option A is correct.
The rate-limiting step is the step in a reaction that has the highest activation energy and therefore proceeds at the slowest rate. It sets the overall rate of the reaction because the other steps in the reaction cannot occur faster than the rate of the rate-limiting step.
However, the rate law of the reaction is determined by the slowest elementary step, which may or may not be the rate-limiting step.
The rate-limiting step is not always the first step in a reaction. It can be any step in the reaction mechanism.
To learn more about the rate-limiting step, follow the ;ink:
https://brainly.com/question/30676099
#SPJ12
which was an assumption bohr made in his model? select the correct answer below: wavelengths have negative values. energy values were quantized. neutrons are negatively charged. electrons are found in the nucleus.
Electrons are found in orbits around the nucleus. This was an assumption Bohr made in his model.
Compared to the valence shell model, the Bohr's model of the hydrogen atom is quite simple. It may be seen as an outmoded scientific theory since it may be derived from the more comprehensive and precise quantum mechanics as a first-order approximation of the hydrogen atom.To expose students to quantum mechanics or energy level diagrams before moving on to the more accurate but more challenging valence shell atom, the Bohr model is still often used in classroom instruction.This is due of its simplicity and its right conclusions for a few systems.
learn more about Bohr's model Refer:brainly.com/question/11801538
#SPJ1