The dark region between the two rainbows is due to the critical angle at which light rays are reflected away from the observer's eye, and this angle depends on the size of the rain droplets.
When two rainbows form, there is a dark region in-between them because of the critical angle. This critical angle is the minimum angle of incidence beyond which total internal reflection of a light ray occurs from the water droplets in the atmosphere. Because of this angle, the light that reflects from the rain droplets moves away from the observer's eye, so a dark region is formed between the two rainbows.
The light that enters the drop slows down and bends, and the angle of bending is dependent on the color of the light. Red light is bent the least, while violet is bent the most, causing the separation of the colors in a rainbow. The angle of incidence can vary based on the size of the rain droplets, which is why two rainbows can form with different angles of incidence producing the different colors.
Thus, the dark region between the two rainbows is due to the critical angle at which light rays are reflected away from the observer's eye, and this angle depends on the size of the rain droplets.
Learn more about critical angle here,
https://brainly.com/question/31073422
#SPJ11
a) What is the thinnest film of MgF2 (n=1.38) on glass (n=1.5) that produces a strong reflection for 600 nm orange light? b) What is the thinnest film that produces a minimum reflection, like an anti-reflection coating?
Answer:
a) Strong reflection for 600 nm orange light is approximately 217.39 nm.
b) Anti-reflection coating, is approximately 434.78 nm.
a) To determine the thinnest film of MgF2 on glass that produces a strong reflection for 600 nm orange light, we can use the concept of thin film interference.
The condition for strong reflection is when the phase change upon reflection is 180 degrees.
The phase change due to reflection from the top surface of the film is given by:
Δφ = 2πnt/λ
Where Δφ is the phase change,
n is the refractive index of the film (MgF2),
t is the thickness of the film, and
λ is the wavelength of the light.
For strong reflection, the phase change should be 180 degrees. Therefore, we can set up the equation:
2πnt/λ = π
Simplifying the equation:
nt/λ = 1/2
Rearranging the equation to solve for the thickness of the film:
t = (λ/2n)
Wavelength of orange light, λ = 600 nm = 600 x 10^(-9) m
Refractive index of MgF2, n = 1.38
Substituting the values into the equation:
t = (600 x 10^(-9) m) / (2 x 1.38)
t ≈ 217.39 nm
Therefore, the thinnest film of MgF2 on glass that produces a strong reflection for 600 nm orange light is approximately 217.39 nm.
b) To determine the thinnest film that produces a minimum reflection, like an anti-reflection coating, we need to consider the condition for destructive interference. For minimum reflection, the phase change upon reflection should be 0 degrees.
Using the same equation as above:
2πnt/λ = 0
Simplifying the equation:
nt/λ = 0
Since the thickness of the film cannot be zero, we need to consider the next possible value that gives destructive interference. In this case, we can choose a thickness that results in a phase change of 360 degrees (or any multiple of 360 degrees).
nt/λ = 1
Rearranging the equation to solve for the thickness:
t = λ/n
Substituting the values:
t = (600 x 10^(-9) m) / 1.38
t ≈ 434.78 nm
Therefore, the thinnest film of MgF2 on glass that produces a minimum reflection, like an anti-reflection coating, is approximately 434.78 nm.
Learn more about anti-reflection coating here
https://brainly.com/question/31490655
#SPJ11
. Sunlight falls on a soap film 360 nm thick. The soap film has an index of 1.25 and lies on top of water of index 1.33. Find (a) the wavelength of visible light most strongly reflected, and (b) the wavelength of visible light that is not seen to reflect at all. Estimate the colors.
(a) The wavelength of visible light most strongly reflected is 720 nm. This corresponds to the color red in the visible spectrum.(b) The soap film will strongly reflect red light (720 nm) and not reflect violet light (240 nm), giving rise to the colors observed in thin film interference.
The wavelength of visible light most strongly reflected and the wavelength of visible light that is not seen to reflect at all, we can use the principles of thin film interference.
(a) The wavelength of visible light most strongly reflected can be determined using the equation for constructive interference in a thin film:
2t = mλ
where t is the thickness of the film, λ is the wavelength of light, and m is the order of the interference. In this case, we are looking for the first-order interference (m = 1).
t = 360 nm = 360 x 10^-9 m
n1 (index of soap film) = 1.25
n2 (index of water) = 1.33
We can rearrange the equation to solve for λ:
λ = 2t / m
For m = 1:
λ = 2(360 x 10^-9 m) / 1
= 720 x 10^-9 m
= 720 nm
So, the wavelength of visible light most strongly reflected is 720 nm. This corresponds to the color red in the visible spectrum.
(b) The wavelength of visible light that is not seen to reflect at all corresponds to the wavelength of light that experiences destructive interference. In this case, we can use the equation:
2t = (m + 1/2)λ
Using the same values as before, we can solve for λ:
λ = 2t / (m + 1/2)
For m = 1:
λ = 2(360 x 10^-9 m) / (1 + 1/2)
= 2(360 x 10^-9 m) / (3/2)
= (2/3)(360 x 10^-9 m)
= 240 x 10^-9 m
= 240 nm
So, the wavelength of visible light that is not seen to reflect at all is 240 nm. This corresponds to the color violet in the visible spectrum.
Therefore, the soap film will strongly reflect red light (720 nm) and not reflect violet light (240 nm), giving rise to the colors observed in thin film interference.
Learn more about wavelength
https://brainly.com/question/31524177
#SPJ11
A long solenoid with n= 35 turns per centimeter and a radius of R= 12 cm carries a current of i= 35 mA. Find the magnetic field in the solenoid. The magnetci field, Bo 176.6 x Units UT If a straight conductor is positioned along the axis of the solenoid and carries a current of 53 A, what is the magnitude of the net magnetic field at the distance R/2 from the axis of the solenoid? The net magnetic field, Bret = 176.61 Units
Answer:
1) The magnetic field inside the solenoid is approximately 0.0389 Tesla.
2) The magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
To find the magnetic field inside the solenoid, we can use the formula for the magnetic field inside a solenoid:
B = μ₀ * n * i
Where:
B is the magnetic field
μ₀ is the permeability of free space (4π * 10^(-7) T·m/A)
n is the number of turns per unit length
i is the current
n = 35 turns/cm
= 35 * 100 turns/m
= 3500 turns/m
i = 35 mA
= 35 * 10^(-3) A
Substituting the values into the formula:
B = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B ≈ 0.0389 T
Therefore, the magnetic field inside the solenoid is approximately 0.0389 Tesla.
To find the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid due to the solenoid and the straight conductor, we can sum the magnetic fields produced by each separately.
The magnetic field at a distance R/2 from the axis of the solenoid can be found using the formula:
B_sol = μ₀ * n * i
n = 3500 turns/m
i = 35 * 10^(-3) A
Substituting the values into the formula:
B_sol = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B_sol ≈ 0.0389 T
The magnetic field at a distance R/2 from a long straight conductor carrying a current can be found using Ampere's law:
B_conductor = (μ₀ * i) / (2π * R/2)
i = 53 A
R = 12 cm = 0.12 m
Substituting the values into the formula:
B_conductor = (4π * 10^(-7) T·m/A * 53 A) / (2π * 0.12 m)
Calculating:
B_conductor ≈ 0.0035 T
To find the net magnetic field, we can add the magnitudes of the magnetic fields produced by the solenoid and the conductor:
B_net = |B_sol| + |B_conductor|
Substituting the values:
B_net = |0.0389 T| + |0.0035 T|
Calculating:
B_net ≈ 0.0424 T
Therefore, the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
Learn more about solenoid, here
https://brainly.com/question/1873362
#SPJ11
A laser emits radiations with a wavelength of λ=470 nm. How many photons are emitted per second if the laser has a power of 1.5 mW?
The number of photons emitted per second is 7.4 × 10^14 photons/second when a laser emits radiations with a wavelength of λ = 470 nm and has a power of 1.5 mW.
The given values are:Power, P = 1.5 mWavelength, λ = 470 nmWe can use the formula to find the number of photons emitted per second.N = P / (E * λ)Where,N is the number of photons emitted per secondP is the power of the laserE is the energy of each photonλ is the wavelength of the lightE = hc / λ.
Where,h is the Planck's constant (6.626 × 10^-34 J s)c is the speed of light (3 × 10^8 m/s)Putting the given values in E = hc / λWe get,E = (6.626 × 10^-34) × (3 × 10^8) / (470 × 10^-9)E = 4.224 × 10^-19 JNow, putting the values of P, E, and λ in the above equation:N = P / (E * λ)N = (1.5 × 10^-3) / (4.224 × 10^-19 × 470 × 10^-9)N = 7.4 × 10^14 photons/second.
Therefore, the number of photons emitted per second is 7.4 × 10^14 photons/second when a laser emits radiations with a wavelength of λ = 470 nm and has a power of 1.5 mW.
Learn more about wavelength here,
https://brainly.com/question/10750459
#SPJ11
Part A: Calculate the work done (in SI units) when 1 mole of gas expands from 5 dmº to 10 dm2 against a constant pressure of 1 atmosphere. Part B: A steam turbine is operating under the following conditions: steam to the turbine at 900°F and 120 psia, velocity – 250 ft/s; steam exiting at 700°F and 1 atm, velocity = 100 fts. Under these conditions, the enthalpy rate in and out are given as 1478.8 Btu/lb and 1383.2 Btu/lb as read from the steam tables, respectively. Calculate the rate at which work (in horsepower, hp) can be obtained from the turbine if the steam flow is 25,000 lb/h and the turbine operation is steady stat adiabatic.
Part A: the work done by 1 mole of gas is 0.5065 J. Part B: the rate at which work can be obtained from the turbine is 9286.36 hp.
Part A:Work done by an ideal gas is given by W = pΔV. Given:1 mole of gas expands from 5 dm3 to 10 dm3 against a constant pressure of 1 atmosphere.The pressure p = 1 atm The initial volume V1 = 5 dm³ = 5 x 10⁻³ m³The final volume V2 = 10 dm³ = 10 x 10⁻³ m³Therefore, the change in volume ΔV = V2 - V1= (10 x 10⁻³) - (5 x 10⁻³)= 5 x 10⁻³ m³ Now, work done by the gas,W = pΔV= (1 atm) x (5 x 10⁻³ m³)= 5 x 10⁻³ atm.m³ But, 1 atm.m³ = 101.3 J Therefore, W = (5 x 10⁻³) x 101.3= 0.5065 J Hence, the work done by 1 mole of gas is 0.5065 J.
Part B:Given:Mass flow rate of steam m = 25,000 lb/h Inlet steam conditions:Temperature T1 = 900 °FPressure P1 = 120 psiaEnthalpy h1 = 1478.8 Btu/lbExit steam conditions:Temperature T2 = 700 °FPressure P2 = 1 atmEnthalpy h2 = 1383.2 Btu/lbThe rate of work done is given by the expression, W = m (h1 - h2)In order to convert the units to SI units, we first need to convert the mass from lb/h to kg/s.1 lb = 0.4536 kg; 1 h = 3600 sTherefore, 1 lb/h = 0.4536/3600 kg/s = 1.26 x 10⁻⁴ kg/s Mass flow rate of steam m = 25,000 lb/h = 3.15 kg/s.
Therefore, the rate of work done isW = m (h1 - h2) = (3.15) (h1 - h2) Let's convert the enthalpies from Btu/lb to J/kg,1 Btu = 1055.06 J; 1 lb = 0.4536 kg Therefore, 1 Btu/lb = 2326 J/kgEnthalpy h1 = 1478.8 Btu/lb = 1478.8 x 2326 J/kg= 3.44 x 10⁶ J/kgEnthalpy h2 = 1383.2 Btu/lb = 1383.2 x 2326 J/kg= 3.22 x 10⁶ J/kgSubstituting the values in the equation,W = m (h1 - h2) = (3.15) (3.44 x 10⁶ - 3.22 x 10⁶)= 6.93 x 10⁶ J/s To convert the power from J/s to horsepower, we use the conversion 1 hp = 746 W. Power P = W/746= (6.93 x 10⁶) / 746= 9286.36 hp .
Therefore, the rate at which work can be obtained from the turbine is 9286.36 hp.
Learn more about horsepower here,
https://brainly.com/question/28994705
#SPJ11
how can determine the frequency and wavelength of the sound when it hits a 15 feet tall tree
The frequency of sound when it hits a 15 feet tall tree is 37.5 Hz and the wavelength is 9.144 meters.
The wavelength and frequency of sound can be determined when it hits a 15 feet tall tree by using the formula:
f = v/λ
Where,
f = frequency
v = velocity of sound
λ = wavelength
We can assume that the velocity of sound in air is 343 meters per second (m/s) at standard conditions (0°C and 1 atm pressure).
To convert 15 feet to meters, we can use the conversion factor 1 foot = 0.3048 meters.
So,
15 feet = 15 × 0.3048
= 4.572 meters.
The wavelength (λ) can be calculated using the formula:
λ = 2L
Where,
L = length of the tree = 4.572 meters
λ = 2 × 4.572λ = 9.144 meters
The frequency (f) can now be calculated using the formula:
f = v/λ
f = 343/9.144
f = 37.5 Hz
Therefore, the frequency of sound when it hits a 15 feet tall tree is 37.5 Hz and the wavelength is 9.144 meters.
Learn more about the wavelength:
brainly.com/question/10750459
#SPJ11
A cooling fan is turned off when it is running at 9.2 rad/s. It turns 25 rad before it comes to a stop. What is the fan's angular acceleration in rad/s?? -1.48 -1.69 -1.73 -158 An iron object of density 7.80g/cm appears 27 N lighter in water than in air. What is the volume of the object?
a. the angular acceleration in rad/s² of the cooling fan is -16.16 rad/s². Hence, the correct option is -16.16 rad/s².
b. the volume of the iron object is 0.35 cm³. Thus, the correct option is 0.35.
a. The angular acceleration in rad/s² of the cooling fan that has been turned off when running at 9.2 rad/s and it turns 25 rad before it comes to a stop can be calculated using the formula shown below:
ωf = 0rad/s;
ωi = 9.2rad/s;
θ = 25 rad(ωf)² = (ωi)² + 2αθ
α = (ωf² - ωi²)/2θ
α = ((0)² - (9.2)²)/2(25)
α = -16.16 rad/s²
b. The volume of an iron object of density 7.80g/cm appears 27 N lighter in water than in air can be calculated using the formula shown below:
Buoyant force = mg
Apparent weight in water = Weight in air - Buoyant force
Therefore, 27 = mg - ρVg
27 = g(m - ρV)
V = (m - ρV) / ρV = (m / ρ) - 1
V = (27 / 9.8 x 7.80) - 1
V = 0.35 cm³
To learn more about angular acceleration, refer:-
https://brainly.com/question/1980605
#SPJ11
Halley's comet, which passes around the Sun every 76 years, has an elliptical orbit. When closest to the Sun (perihelion) it is at a distance of 8.823 x 100 m and moves with a speed of 54.6 km/s. When farthest from the Sun (aphelion) it is at a distance of 6.152 x 10¹2 m and moves with a speed of 783 m/s. Part A Find the angular momentum of Halley's comet at perihelion. (Take the mass of Halley's comet to be 9.8 x 10¹4 kg.)
The angular momentum of Halley's comet at perihelion is 5.92 x 10^17 kg⋅m²/s.
Angular momentum (L) is defined as the product of the moment of inertia (I) and the angular velocity (ω) of an object. In this case, we can calculate the angular momentum of Halley's comet at perihelion using the formula L = I * ω.
The moment of inertia of a point mass rotating around a fixed axis is given by I = m * r², where m is the mass and r is the distance from the axis of rotation. In this case, the mass of Halley's comet is given as 9.8 x 10^14 kg, and at perihelion, the distance from the Sun is 8.823 x 10^10 m. Therefore, we can calculate the moment of inertia as I = (9.8 x 10^14 kg) * (8.823 x 10^10 m)².
The angular velocity (ω) can be calculated by dividing the linear velocity (v) by the radius (r) of the orbit. At perihelion, the linear velocity of the comet is given as 54.6 km/s, which is equivalent to 54.6 x 10^3 m/s. Dividing this by the distance from the Sun at perihelion (8.823 x 10^10 m), we obtain the angular velocity ω.
Substituting the values into the formula L = I * ω, we can calculate the angular momentum of Halley's comet at perihelion.
Learn more about angular velocity here:
https://brainly.com/question/30237820
#SPJ11
A track and field athlete applies a force of 150N the length of her arm (0.5m) directly upward to a 7.26kg shot put. How high does the shot put travel above her arm?
The shot put travels approximately 1.08 meters above the athlete's arm.
To determine how high the shot put travels above the athlete's arm, we need to consider the work done by the athlete's force and the change in gravitational potential energy of the shot put.
The work done by the athlete's force is given by the formula:
Work = Force × Distance × cos(θ)
In this case, the force applied is 150 N, the distance is 0.5 m (the length of the athlete's arm), and θ is the angle between the force and the displacement, which is 0 degrees since the force is applied directly upward.
Therefore, cos(θ) is equal to 1.
Work = 150 N × 0.5 m × cos(0°) = 75 joules
The work done by the athlete's force is equal to the change in gravitational potential energy of the shot put:
Work = ΔPE
ΔPE = m × g × h
Where m is the mass of the shot put (7.26 kg), g is the acceleration due to gravity (approximately 9.8 m/s²), and h is the height above the athlete's arm.
Substituting the known values:
75 joules = 7.26 kg × 9.8 m/s² × h
Simplifying the equation:
h = 75 joules / (7.26 kg × 9.8 m/s²)
h ≈ 1.08 meters
Therefore, the shot put travels approximately 1.08 meters above the athlete's arm.
To learn more about gravitational potential energy visit:
brainly.com/question/3884855
#SPJ11
Consider a D/A converter for audio signals consisiting of a zero-order-hold interpolator followed by a continuous- time lowpass filter with positive passband between 0 and 20KHz and stopband starting at fa = 40KHz. = Assume we want to convert a digital signal originally sampled at 16KHz. What is the minimum oversampling factor that we need to use?
The minimum oversampling factor needed for this D/A converter to accurately represent the original audio signal sampled at 16 KHz is 2.5.
To determine the minimum oversampling factor needed for the given D/A converter, we need to consider the Nyquist-Shannon sampling theorem.
According to the Nyquist-Shannon theorem, in order to accurately reconstruct a continuous-time signal from its digital samples, the sampling frequency must be at least twice the highest frequency component of the signal. This is known as the Nyquist rate.
In this case, the digital signal was originally sampled at 16 KHz. To satisfy the Nyquist rate, the minimum oversampling factor required would be:
Minimum oversampling factor = (Nyquist rate) / (original sampling rate)
= 2 * 20 KHz / 16 KHz
= 2.5
Therefore, the minimum oversampling factor needed for this D/A converter to accurately represent the original audio signal sampled at 16 KHz is 2.5.
To learn more about Nyquist-Shannon sampling theorem, visit:
https://brainly.com/question/31735568
#SPJ11
A heavy crate rests on an unpolished surface. Pulling on a rope attached to the heavy crate, a laborer applies a force which is insufficient to move it. From the choices presented, check all of the forces that should appear on the free body diagram of the heavy crate.
The force of kinetic friction acting on the heavy crate. An inelastic or spring force applied to the heavy crate. The force on the heavy crate applied through the tension in the rope. The force of kinetic friction acting on the shoes of the person. The force of static friction acting on the heavy crate. The weight of the person. The force of static friction acting on the shoes of the person. The weight of the heavy crate. The normal force of the heavy crate acting on the surface. The normal force of the surface acting on the heavy crate.
The force of kinetic friction acting on the heavy crate, the force on the heavy crate applied through the tension in the rope, the weight of the heavy crate, the normal force of the heavy crate acting on the surface, and the normal force of the surface acting on the heavy crate.
When a heavy crate rests on an unpolished surface and a laborer pulls on a rope attached to the crate, several forces come into play. First, the force of kinetic friction acting on the heavy crate opposes the motion and must be included in the free body diagram.
Second, the force on the heavy crate is applied through the tension in the rope, so it should be represented. Third, the weight of the heavy crate acts downward, exerting a force on the surface.
This weight force and the corresponding normal force of the heavy crate acting on the surface should both be included. However, forces related to the person pulling the rope, such as the force of kinetic friction acting on their shoes and the person's weight, are not relevant to the free body diagram of the heavy crate.
Learn more about kinetic friction here:
https://brainly.com/question/30886698
#SPJ11
A cord is used to vertically lower an initially staticnary block of mass M = 13 kg at a constant dowrtward acceleration of g/7. When the block has fallen a distance d = 2.4 m, find (a) the work done by the cord's force on the block, (b) the work done by the gravitational force on the block, (c) the kinetic energy of the block, and (d) the speed of the block. (Note: Take the doweward direction positive) (a) Number ________________ Units _________________
(b) Number ________________ Units _________________
(c) Number ________________ Units _________________
(d) Number ________________ Units _________________
(a) The work done by the cord's force on the block is 201.5856J
Number: 201.5856. Units: Joules (J)
(b) The work done by the gravitational force on the block is 306.072 J.
Number: 306.072 . Units: Joules (J)
(c) The kinetic energy of the block is 45.7549
Number: 45.7549 . Units: Joules (J)
(d) The speed of the block is 2.619 m/s.
Number: 2.619. Units: m/s
(a)
Number:
Work done by the cord's force on the block is given by:
W = F × d
The cord's force is equal to the force due to gravity acting on the block minus the force required to give the block an acceleration of g/7.
i.e., Fcord = Mg - Ma
Here,
acceleration of the block, a = g/7
Fcord = Mg - Ma
= 13 × 9.81 - 13 × (9.81/7)
= 13 × 9.81 × 6 / 7
= 83.994 N
Using the formula for work done by the cord's force,
W = Fcord × d
= 83.994 × 2.4
= 201.5856J
Therefore, the work done by the cord's force on the block is 201.5856J.
Units: Joules (J)
(b)
Number:
Work done by the gravitational force on the block is given by:
W = Fg × d
Where, Fg is the force due to gravity acting on the block.
Fg = Mg
= 13 × 9.81
= 127.53 N
Using the formula for work done by the gravitational force,
W = Fg × d
= 127.53 × 2.4
= 306.072 J
Therefore, the work done by the gravitational force on the block is 306.072 J.
Units: Joules (J)
(c)
Number:
The kinetic energy of the block is given by:
K.E. = ½mv²
where, m is the mass of the block, and v is its velocity.
The final velocity of the block can be calculated using the formula:
v² - u² = 2as
where,
u is the initial velocity of the block (which is 0 m/s),
a is the acceleration of the block (which is g/7), and
s is the distance traveled by the block (which is 2.4 m).
v² = 2as
= 2 × (9.81/7) × 2.4
= 6.85714
v = √(6.85714)
= 2.619 m/s
Therefore, the kinetic energy of the block is given by:
K.E. = ½mv²
= ½ × 13 × (2.619)²
= 45.7549 J
Therefore, the kinetic energy of the block is 45.7549
Units: Joules (J)
(d) Number:
The speed of the block is given by:
v² - u² = 2as
v² = 2as
= 2 × (9.81/7) × 2.4
= 6.85714
v = √(6.85714)
= 2.619 m/s
Therefore, the speed of the block is 2.619 m/s.
Units: m/s.
Learn more about the work done:
brainly.com/question/21854305
#SPJ11
Water flows through a garden hose (radius =1.5 cm ) and fills a tub of volume V=670 Liters in Δt=6.0 minutes. What is the speed of the water in the hose in meters per second?
For the volume of 670 liters and the time of 6.0 minutes, the speed of the water in the hose is approximately 0.043 meters per second.
The speed of water in the hose can be calculated by dividing the volume of water that flows through the hose by the time it takes to fill the tub.
Given that the volume is 670 liters and the time is 6.0 minutes, we can determine the speed of the water in meters per second.
To find the speed of the water in the hose, we need to convert the given volume and time into consistent units.
First, let's convert the volume from liters to cubic meters.
Since 1 liter is equal to 0.001 cubic meters, we have:
V = 670 liters = 670 * 0.001 cubic meters = 0.67 cubic meters
Next, let's convert the time from minutes to seconds.
Since 1 minute is equal to 60 seconds, we have:
Δt = 6.0 minutes = 6.0 * 60 seconds = 360 seconds
Now, we can calculate the speed of the water using the formula:
Speed = Volume / Time
Speed = 0.67 cubic meters / 360 seconds ≈ 0.00186 cubic meters per second
Since the speed is given in cubic meters per second, we can convert it to meters per second by taking the square root of the speed:
Speed = √(0.00186) ≈ 0.043 meters per second
Therefore, the speed of the water in the hose is approximately 0.043 meters per second.
Learn more about speed here:
https://brainly.com/question/13943409
#SPJ11
heavy uniform beam of mass 25 kg and length 1.0 m is supported at rest by two ropes, as shown. The left rope is attached at the left end of the beam while the right rope is secured 3/4 of the beam's length away to the right. Determine the fraction of the beam's weight being supported by the rope on the right. In other words, determine: TR Wbeam 0 0 0.5 0.67 0.83 0.75
The rope on the right can support the entire weight of the beam, so the fraction of the beam's weight being supported by that rope is 1 or 100%.
The fraction of the beam's weight being supported by the rope on the right can be determined by analyzing the torque equilibrium of the beam.
Let's denote the weight of the beam as W_beam.
Since the beam is uniform, we can consider its weight to act at its center of mass, which is located at the midpoint of the beam.
To calculate the torque, we need to consider the distances of the two ropes from the center of mass of the beam.
The left rope is attached at the left end of the beam, so its distance from the center of mass is 0.5 m.
The right rope is secured 3/4 of the beam's length away to the right, so its distance from the center of mass is 0.75 m.
In torque equilibrium, the sum of the torques acting on the beam must be zero.
The torque exerted by the left rope is TR (tension in the rope) multiplied by its distance from the center of mass (0.5 m), and the torque exerted by the right rope is TR multiplied by its distance from the center of mass (0.75 m).
Since the beam is at rest, the sum of these torques must be zero.
Therefore, we can set up the equation:
TR * 0.5 - TR * 0.75 = 0
Simplifying the equation, we find:
-0.25TR = 0
Since the left side of the equation is zero, the tension in the right rope (TR) can be any value.
This means that the right rope can support the entire weight of the beam, so the fraction of the beam's weight being supported by the rope on the right is 1.
In summary, the rope on the right can support the entire weight of the beam, so the fraction of the beam's weight being supported by that rope is 1 or 100%.
Learn more about torque here:
https://brainly.com/question/31323759
#SPJ11
In the figure, a horse pulls a barge along a canal by means of a rope. The force on the barge from the rope has a magnitude of 7910N and is at the angle θ=15 ∘
from the barge's motion, which is in the positive direction of an x axis extending along the canal. The mass of the barge is 9500 kg, and the magnitude of its acceleration is 0.12 m/s 2
. What are (a) the magnitude and (b) the direction (measured from the positive direction of the x axis) of the force on the barge from the water? Give your answer for (b) in the range of (−180 ", 180%
Thus, the direction of the force on the barge from the water is -57° relative to the positive direction of the x-axis.
(a) The magnitude of the force on the barge from the water is 1.15 × 10^4 N.(b) The direction of the force on the barge from the water is -57° relative to the positive direction of the x-axis.In the given figure, a horse is pulling a barge along a canal by means of a rope.
The force on the barge from the rope has a magnitude of 7910 N and is at an angle of θ = 15° from the barge's motion, which is in the positive direction of an x-axis extending along the canal.
The mass of the barge is 9500 kg, and the magnitude of its acceleration is 0.12 m/s^2.(a) Magnitude of the force on the barge from the water:Let's find out the magnitude of the force on the barge from the water:We know that,F_net = m × aWhere,F_net = Net force acting on the barge = Force exerted by the rope - Force exerted by the water
Thus,F_net = 7910 N - F_wNet force F_net = (9500 kg)(0.12 m/s^2)F_net = 1140 NThus,7910 N - F_w = 1140 N- F_w = -6770 N|F_w| = 6770 NThus, the magnitude of the force on the barge from the water is 1.15 × 10^4 N.(b) Direction of the force on the barge from the water:
The direction of the force on the barge from the water is given by:θ = tan⁻¹(F_w/F_net)θ = tan⁻¹(-6770/7910)θ = -37.23°
Thus, the direction of the force on the barge from the water is -57° relative to the positive direction of the x-axis.
to more know about direction
https://brainly.com/question/29248951
#SPJ11
This problem involves using Newton's second law in two dimensions. We can find the magnitude and direction of the force from the water by setting up and solving equations for the forces in the horizontal and vertical directions.
Explanation:This problem relates to Newton’s second law of motion in two dimensions and can be solved by considering the forces in both the x and y direction. Given that the total force acting on the barge is the sum of the force from the rope and the force from water, we have the equations:
F_total = F_rope + F_water = m*a.
For the x direction (horizontal): m*a = F_rope_cos(θ) – F_water_x,
and for the y direction (vertical): 0 = F_rope_sin(θ) + F_water_y.
To find the magnitude (a) and the direction (b) of the water force, you can solve these equations considering that the force from the rope is 7910N at an angle of 15 degrees from the horizontal, the mass of the barge is 9500kg and its acceleration is 0.12m/s².
Learn more about Newton’s second law here:https://brainly.com/question/18769451
#SPJ12
Perpetual motion machines are theoretical devices that, once in motion do not stop, and continue on without the addition of any extra energy source (often by alternating energy between kinetic and gravitational potential).
a) Why are these not possible?
b) Some people claim that a true perpetual motion machine would be able to produce infinite energy. Why does this not make sense?
Perpetual motion machines, which operate without the need for additional energy input, are not possible due to the fundamental principles of thermodynamics. Such machines would violate the laws of thermodynamics, specifically the first and second laws.
Claims of producing infinite energy through perpetual motion machines do not make sense because they disregard the conservation of energy and overlook the limitations imposed by the laws of thermodynamics.
Perpetual motion machines violate the first law of thermodynamics, also known as the law of energy conservation, which states that energy cannot be created or destroyed, only transferred or transformed from one form to another.
In a closed system, such as a perpetual motion machine, the total amount of energy remains constant. Without an external energy source, the machine would eventually come to a halt due to energy loss through various factors like friction, air resistance, and mechanical inefficiencies.
The second law of thermodynamics, known as the law of entropy, states that in a closed system, the entropy (or disorder) tends to increase over time.
This implies that energy will always tend to disperse and spread out, resulting in a loss of useful energy for performing work. Perpetual motion machines would defy this law by maintaining a perpetual cycle of energy conversion without any losses, which is not possible.
The claim that a perpetual motion machine could produce infinite energy is flawed because it disregards the fact that energy cannot be created from nothing.
The laws of thermodynamics dictate that the total energy within a closed system is conserved. Even if a perpetual motion machine were to function indefinitely, it would not generate additional energy beyond what was initially provided.
Energy would be continuously transformed, but not created or increased, making the concept of infinite energy generation impossible within the confines of known physical laws.
In conclusion, perpetual motion machines are not possible because they violate the laws of thermodynamics. These machines cannot sustain continuous motion without an external energy source and are subject to energy losses and the inevitable increase in entropy.
Claims of infinite energy generation through perpetual motion machines are unfounded as they contradict the principles of energy conservation and the limitations imposed by the laws of thermodynamics.
Learn more about motion here ;
https://brainly.com/question/12640444
#SPJ11
Water from a fire hose is directed horizontally against a wall at a rate of 50.0 kg/s and a speed of 42.0 m/s. Calculate the magnitude of the force exerted on the wall, assuming the waters horizontal momentum is reduced to zero
The magnitude of the force exerted on the wall is large but not infinite.
To determine the magnitude of the force exerted on the wall, we can use the principle of conservation of momentum. The initial momentum of the water stream is given by the product of its mass and velocity:
Initial momentum = mass × velocity = 50.0 kg/s × 42.0 m/s = 2100 kg·m/s
Since the water's horizontal momentum is reduced to zero, the final momentum is zero:
Final momentum = 0 kg·m/s
According to the conservation of momentum, the change in momentum is equal to the impulse applied, which can be calculated using the equation:
Change in momentum = Final momentum - Initial momentum
0 kg·m/s - 2100 kg·m/s = -2100 kg·m/s
The negative sign indicates that the change in momentum is in the opposite direction to the initial momentum. By Newton's third law of motion, this change in momentum is equal to the impulse exerted on the wall. Therefore, the magnitude of the force exerted on the wall is equal to the change in momentum divided by the time it takes for the water to come to rest.
Assuming the water comes to rest almost instantaneously, we can approximate the time taken as very small (approaching zero). In this case, the force can be approximated as infinite. However, in reality, the force would be large but finite, as it takes some time for the water to slow down and come to rest completely.
It's important to note that this approximation assumes idealized conditions and neglects factors such as water absorption by the wall or the reaction force of the wall. In practice, the wall would experience a large force but not an infinite one.
Learn more about magnitude
https://brainly.com/question/18865474
#SPJ11
A 1.40-m-long metal bar is pulled to the right at a steady 4.8 m/s perpendicular to a uniform, 0.715-T magnetic field. The bar rides on parallel metal rails connected through R=25.8−Ω, as shown in the figure, so the apparatus makes a complete circuit. You can ignore the resistance of the bar and the rails. Calculate the magnitude of the emf induced in the circuit. 4,8 V 0.186 V 2,45 V 124 V
The magnitude of the emf induced in the circuit is 124 V.
When a metal bar is pulled at a steady rate through a magnetic field, an electromotive force (emf) is induced. This emf is caused by a change in the magnetic flux that passes through the circuit that the bar is a part of.
According to Faraday’s law, the magnitude of this induced emf is equal to the rate of change of the magnetic flux, or emf=−NΔΦΔt, where N is the number of turns in the circuit, and ΔΦΔt is the rate of change of the magnetic flux that passes through each turn of the circuit. In this case, the bar is being pulled through a uniform magnetic field of 0.715 T at a steady rate of 4.8 m/s.
The magnetic flux that passes through the circuit is then equal to BAh, where A is the area of each turn of the circuit, h is the height of each turn of the circuit, and B is the strength of the magnetic field. Since the bar is moving perpendicular to the magnetic field, the area of each turn of the circuit that the bar moves through is simply equal to the length of the bar times the height of each turn.
Therefore, A=1.40m×h. The rate of change of the magnetic flux is then equal to BAdhdt, where dhdt is the rate at which the bar is moving through the circuit.
Therefore, emf=−NABdhdt=−NABv. In this case, the bar is connected to parallel metal rails connected through R=25.8Ω, which form a complete circuit.
The induced emf then drives a current I=emfR through this circuit. Since the resistance of the bar and the rails is ignored, the induced emf is simply equal to the voltage across the resistance R, or emf=IR.
Therefore, emf=I(R)=−NABvR.
Substituting the given values, we have emf=−1×0.715×(1.40m×h)×4.8ms−1×25.8Ω=−124V.
Hence the magnitude of the emf induced in the circuit is 124 V.
Know more about Faraday’s law here,
https://brainly.com/question/33343234
#SPJ11
please help me asnwering this question..!
5) D/C Transformer The input voltage to a transformer is \( 120 \mathrm{~V} \mathrm{DC} \) to the primary coil of 1000 turns. What are the number of turns in the secondary needed to produce an output
Approximately 83.33 turns are needed in the secondary coil to produce an output voltage of 10 VDC in this D/C transformer.
In a transformer, the ratio of the number of turns in the primary coil to the number of turns in the secondary coil determines the voltage transformation. To calculate the number of turns in the secondary coil, we can use the formula:
[tex]Turns_{ratio} = (Voltage_{ratio})^{exponent}[/tex]
In this case, the voltage ratio is the ratio of the output voltage to the input voltage. The exponent is 1 since it's a D/C transformer. So, the equation becomes:
(120 VDC) / (10 VDC) = (1000 turns) / (x turns)
Solving for x, the number of turns in the secondary coil, we find:
x = (1000 turns) * (10 VDC) / (120 VDC)
x ≈ 83.33 turns
Therefore, approximately 83.33 turns are needed in the secondary coil to produce an output voltage of 10 VDC in this D/C transformer.
Learn more about voltage here:
https://brainly.com/question/13396105
#SPJ11
The complete question is:
D/C Transformer The input voltage to a transformer is 120 VDC to the primary coil of 1000 turns. What are the number of turns in the secondary needed to produce an output voltage of 10 VDC ?
A ray of light indexes on a smooth surface and makes an angle of 10° with the surface.
What is the angle of incidence?
a) 10° b) 20° c) 50° d) 40° e) 80°
The angle of incidence in this scenario is 10°.The angle of incidence is the angle between the incident ray (the incoming ray of light) and the normal to the surface it strikes.
In this case, the problem states that the ray of light indexes on a smooth surface and makes an angle of 10° with the surface. Since the angle of incidence is defined as the angle between the incident ray and the normal, and the surface is smooth (presumably meaning it is flat), the normal to the surface would be perpendicular to the surface.
Therefore, the angle of incidence is equal to the angle that the incident ray makes with the surface, which is given as 10°. Hence, the correct answer is option a) 10°.
Learn more about angles of incidence here:
https://brainly.com/question/14221826
#SPJ11
Write down the radar equation and analyze it. Discuss how to use
it to design the radar system
The radar equation is a fundamental equation used in radar systems to calculate the received power at the radar receiver. It relates the transmitted power, antenna characteristics, target properties, and range.
Analyzing the radar equation helps understand the factors that influence radar system design and performance.
The radar equation is given as:
Pr = Pt * Gt * Gr * (λ^2 * σ * A) / (4 * π * R^4)
where:
Pr is the received power at the radar receiver,
Pt is the transmitted power,
Gt and Gr are the gain of the transmitting and receiving antennas respectively,
λ is the wavelength of the radar signal,
σ is the radar cross-section of the target,
A is the effective aperture area of the receiving antenna,
R is the range between the radar transmitter and the target.
By analyzing the radar equation, we can understand the factors that affect the received power and the design of a radar system. The transmitted power and the gains of the antennas influence the strength of the transmitted and received signals. The wavelength of the radar signal determines the resolution and target detection capabilities. The radar cross-section (σ) represents the reflectivity of the target and its ability to scatter the radar signal. The effective aperture area of the receiving antenna (A) determines the ability to capture and detect the weak reflected signals. The range (R) between the radar and the target affects the received power.
To design a radar system, the radar equation can be used to determine the required transmitted power, antenna characteristics, and sensitivity of the receiver to achieve a desired level of received power. The equation helps in optimizing the antenna gain, choosing the appropriate radar frequency, and considering the target characteristics. By understanding the radar equation and its parameters, engineers can design radar systems with the desired range, resolution, and target detection capabilities while considering factors such as power consumption, signal processing, and environmental conditions.
Learn more about radar frequency here:- brainly.com/question/30504997
#SPJ11
You just realized that your analog wristwatch is always 25 seconds behind the real-time. Calculate the angular speed of your Second hand, in milli-ads/s. A 26 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 56 revolutions per minute. The lifting drum is situated on the top floor which is 195 m high. How many seconds will it take to lift bricks, three quarters up the height of the building?
The angular speed of the second hand is 104.67 milli-radians/s.
The drum will take approximately 16.92 seconds to lift bricks three-quarters up the height of the building.
Analog watch is 25 seconds behind the real-time.
Rotational frequency of lifting drum is 56 revolutions per minute.
Diameter of the lifting drum is 700 mm.
The lifting drum is situated on the top floor which is 195 m high.
The mass of the skip is 26 kg.
Conversion factor: 1 minute = 60 s.
Angular speed of the second hand:We know that the time period of the watch is 60 seconds. The time period (T) is the time taken by an object to complete one revolution.
So, Angular speed (ω) = 2π / T = 2π / 60 rad/s = π / 30 rad/s
In milli-radians per second, angular speed = (π / 30) × 10³ milli-radians/s = 104.67 milli-radians/s (approx.)
The length of the steel rope = 195 m. The mass of the skip is 26 kg.
So, Total work done = mgh
where m = mass of the skip = 26 kg
g = acceleration due to gravity = 9.8 m/s²
h = height to which bricks are lifted = (3 / 4) × 195 m = 146.25 m
Total work done = 26 × 9.8 × 146.25 J
Total work done = 37,617 J
The diameter of the lifting drum = 700 mm.
So, Radius of the drum, r = 700 / 2 = 350 mm = 0.35 m
Rotational frequency (n) = 56 rev/min = 56 / 60 rev/s = 0.9333 rev/s
Circumference of drum, C = 2πr = 2 × π × 0.35 = 2.1991 m
The distance traveled by the rope in one revolution of the drum = circumference of drum = 2.1991 m
The distance traveled by the rope in one revolution of the drum = 2.1991 m
Energy required to lift the skip one time = Total work done / efficiency
where efficiency = 90% = 0.9
Work done by the rope in one revolution = energy required / efficiency
Work done by the rope in one revolution = 37,617 J / 0.9 = 41,797 J
The work done by the rope in one revolution of the drum is equal to the work done in lifting the skip one time.
Distance covered by the rope in one revolution of the drum = 2.1991 m
Work done by the rope in one revolution of the drum = 41,797 J
So, the force applied to lift the skip = Work done / Distance = 41,797 / 2.1991 = 19,000 N
The time taken to lift the skip three-quarters of the height of the building can be calculated as follows:Height to which the skip is lifted, h = 146.25 m
Let's say the skip is lifted a distance x at time t.
Since the force is constant, the distance is proportional to time.
x / t = F / m(g - a)
where g = acceleration due to gravity = 9.8 m/s²
a = acceleration of the skip = (F / m)
Distance left to lift the skip = h - x
The initial velocity of the skip = 0 m/s
The final velocity of the skip = vf
Time taken, t = (vf - vi) / a
The final velocity can be calculated using the kinematic equation:
v² - u² = 2as
where u = initial velocity = 0 m/s
v² = 2as
Therefore, v = √(2as)
The acceleration of the skip = (F / m) - g.
a = (F / m) - g
Let's substitute the known values in the equations:
x / t = F / m(g - a)
x / t = F / m(g - (F / m) + g)
x / t = F² / ma
Let's substitute the value of acceleration in the above equation:
x / t = F² / m((F / m) - g)
x / t = F² / (mg - F²)
The height to which the skip is lifted, h = 146.25 m.
The skip is lifted three-quarters of this height. Therefore,
x = 3h / 4 = 109.6875 m
Let's substitute this value in the above equation:
109.6875 / t = F² / (mg - F²)
Let's substitute the known values in the above equation:
109.6875 / t = (19,000)² / (26 × 9.8 - (19,000)²)
109.6875 / t = 361,000,000 / 3,044,000
109.6875t = 30.85
t ≈ 0.282 minutes = 16.92 s
Therefore, it will take approximately 16.92 seconds to lift bricks three-quarters up the height of the building.
Learn more about angular speed: https://brainly.com/question/6860269
#SPJ11
A 350−Ω resistor, an uncharged 2.5−μF capacitor, and a 3−V battery are connected in series. (a) What is the initial current? (b) What is the RC time constant? (c) What is the current after one time constant? (d) What is the voltage on the capacitor after one time constant? a. The initial current through the circuit is mA. b. The RC time constant is ms. c. The current through the circuit after one time constant is mA. d. The voltage on the capacitor after one time constant is V. The label on a battery-powered radio recommends the use of a rechargeable nickel-cadmium cell (nicads), Ithough it has a 1.25-V open-circuit voltage, whereas an alkaline cell has a 1.58-V open-circuit voltage. he radio has a 3.2Ω resistance. a. With a nicad cell, having an internal resistance of 0.04Ω, what is the voltage supplied to the radio, if a single nicad cell is used? The voltage supplied to the radio is V. b. With an alkaline cell, having an internal resistance of 0.2Ω, what is the voltage supplied to the radio, if a single alkaline cell is used? The voltage supplied to the radio is V. c. The radio's effective resistance is lowered when its volume is turned up. At what value of radio's resistance does a nicad cell begin to supply a greater voltage to the radio than an alkaline cell? When the radio has an effective resistance of Ω or smaller, a greater voltage can be obtained with a nicad cell.
The current through the circuit after one time constant is approximately 3.16 mA. The voltage on the capacitor after one time constant is approximately 2.21 V. The voltage supplied to the radio using an alkaline cell is approximately 1.55 V.
(a) To find the initial current, we can use Ohm's Law, which states that current (I) is equal to voltage (V) divided by resistance (R). In this case, the voltage is 3V and the resistance is 350Ω. Therefore, the initial current is:
I = V / R = 3V / 350Ω
(b) The RC time constant is given by the product of the resistance and the capacitance in the circuit. In this case, the resistance is 350Ω and the capacitance is 2.5μF. Therefore, the RC time constant is:
RC = R * C = 350Ω * 2.5μF
(c) After one time constant, the current through the circuit has decayed to approximately 36.8% of its initial value. Therefore, the current after one time constant is:
[tex]I_{after = I_{initial[/tex]l * e^(-1) ≈[tex]I_{initial[/tex]* 0.368
(d) The voltage on the capacitor after one time constant can be calculated using the formula for charging a capacitor in an RC circuit. The voltage on the capacitor ([tex]V_c[/tex]) after one time constant is:
[tex]V_c[/tex] = V * (1 - e^(-1)) ≈ V * 0.632
For the second part of the question:
(a) To find the voltage supplied to the radio using a nicad cell, we need to consider the internal resistance of the cell. The voltage supplied to the radio can be calculated using Ohm's Law:
[tex]V_{supplied = V_{cell - I * r_internal[/tex]
where [tex]V_{cell[/tex] is the open-circuit voltage of the cell, I is the current flowing through the cell, and [tex]r_{internal[/tex] is the internal resistance of the cell.
(b) Similarly, to find the voltage supplied to the radio using an alkaline cell, we use the same formula as in part (a), but with the values specific to the alkaline cell.
(c) To determine the value of the radio's resistance at which the nicad cell supplies a greater voltage than the alkaline cell, we set up the equation:
[tex]V_{nicad = V_{alkaline[/tex]
Solving this equation for the resistance will give us the threshold value.
Learn more about resistor here:
https://brainly.com/question/30672175
#SPJ11
Prove the effective thickness equation.
To prove the effective thickness equation, we need to start with the basic equation for thermal resistance in a composite wall. The thermal resistance of a composite wall can be expressed as:
1/[tex]R_{total[/tex] = Σ[tex](L_i / k_i)[/tex],
where [tex]R_{total[/tex] is the total thermal resistance, [tex]L_i[/tex] is the thickness of each layer i, and [tex]k_i[/tex] is the thermal conductivity of each layer i.
Now, let's consider a composite wall consisting of multiple layers with varying thicknesses. The effective thickness ([tex]L_{eff[/tex]) is defined as the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall. We want to derive an equation for [tex]L_{eff[/tex].
To begin, we can rewrite the thermal resistance equation for the composite wall as:
1/[tex]R_{total[/tex] = ([tex]L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex],
where n is the total number of layers in the composite wall.
Now, we introduce the concept of effective thermal conductivity ([tex]k_{eff)[/tex], which is the thermal conductivity that the composite wall would have if it were replaced by a single imaginary layer with thickness [tex]L_{eff[/tex]. We can express this as:
[tex]k_{eff[/tex] = Σ[tex](L_i / k_i[/tex]).
The effective thermal conductivity represents the ratio of the total thickness of the composite wall to the total thermal resistance.
Next, we can rearrange the equation for the effective thermal conductivity to solve for[tex]L_{eff[/tex]:
[tex]k_{eff = L_{eff / R_{total.[/tex]
Now, we can substitute the expression for the total thermal resistance ([tex]R_{total[/tex]) from the thermal resistance equation:
[tex]k_{eff = L_{eff / ((L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex]).
Finally, by rearranging the equation, we can solve for [tex]L_{eff[/tex]:
[tex]L_eff = k_eff / ((1 / L_1) + (1 / L_2) + ... + (1 / L_n)).[/tex]
This is the effective thickness equation, which gives the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall.
The effective thickness equation allows us to simplify the analysis of composite walls by replacing them with a single equivalent layer. This concept is particularly useful when dealing with heat transfer calculations in complex systems with multiple layers and varying thicknesses, as it simplifies the calculations and reduces the system to an equivalent homogeneous layer.
Learn more about resistance here:
https://brainly.com/question/14547003
#SPJ11
A proton and a deuteron (a particle with the same charge as the proton, but with twice the mass) try to penetrate a barrier of rectangular potential of height 10 MeV and width 10⁻¹⁴ m. The two particles have kinetic energies of 3 MeV. (a) Use qualitative arguments to predict which of the particles have the highest probability of getting it, (b) Quantitatively calculate the probability of success for each of the particles.
A proton and a deuteron (a particle with the same charge as the proton, but with twice the mass) try to penetrate a barrier of rectangular potential of height 10 MeV and width 10⁻¹⁴ m. The two particles have kinetic energies of 3 MeV.
a) Qualitative prediction:
The potential energy barrier is quite high and very wide, which means that it is difficult for any of the two particles to penetrate the barrier. Since the deuteron has twice the mass of the proton, it will have a greater energy density. As a result, it will have a lower kinetic energy, which will make it less likely to overcome the barrier and penetrate it. As a result, a proton will have a greater probability of success when compared to a deuteron. Hence, the proton has the highest probability of getting through the potential barrier.
b) Quantitative calculation:
For the calculation of the probability of success for each of the particles, the transmission coefficient is to be calculated. Transmission coefficient is the ratio of the probability of transmission of a particle to the probability of its incidence. We can calculate the transmission coefficient as follows:
L = e 2 4 π ε 0 Z E − R
By plugging the values in the above equation, we get approx 3.1 * 10^{-29} for proton and approx 8.5* 10^{-32} for deuteron
As we can see, the probability of success for the proton is much higher than that for the deuteron. Therefore, a proton has the highest probability of getting through the potential barrier.
Learn more about the proton: https://brainly.com/question/13683522
#SPJ11
Question 1 1 pts After successfully clearing the bar during the pole vault, the vaulter falls to the landing cushion while trying to calculate the impending impulse which will break his fall. If his momentum is -980 kg.m/s and he has a velocity of -12.5 m/s just prior to landing, what is the mass of the vaulter? 98.1 ks 980.0 kg 78.4 kg BOOK After successfully clearing the bar during the pole vault, the vaulter falls to the landing cushion while trying to calculate the impending Impulse which will break his fall. If his momentum is -980 kg.m/s and he has a velocity of -12.5 m/s just prior to landing, what is the mass of the vaulter? 98.1 ks 980.0 kg 0 78.4 kg 80.0
Answer: The mass of the vaulter is 78.4 kg.
After successfully clearing the bar during the pole vault, the vaulter falls to the landing cushion while trying to calculate the impending impulse which will break his fall.
Momentum = -980 kg.m/s
Velocity = -12.5 m/s
Impulse is the force acting for a specific time and it is given by: Impulse = Momentum = mass × velocity
Impulse = Momentum
Impulse = mass × velocity
mass = Impulse / velocity
Now, substitute the given values of impulse and velocity into the above equation: mass = Impulse / velocity= -980 kg.m/s / -12.5 m/s= 78.4 kg.
Therefore, the mass of the vaulter is 78.4 kg.
Learn more about Momentum : https://brainly.com/question/1042017
#SPJ11
There is a DFB-LD composed of InGaAsP with a central wavelength of 1550 nm and an effective refractive index of 3.6 (a) The change in oscillation wavelength according to the temperature of DFB-LD is +0.1 nm/°C. Assuming that wavelength tuning is performed due to the temperature change of TEC, what is the wavelength tuning range A if it is operated between -20 °C and 80 °C ? (b) We intend to produce a tunable laser array that can use the entire C-band (1525 nm to 1565 nm) using multiple channels of DFB-LD with different center wavelengths. If the temperature range of the TEC is operated between -20 °C and 80 °C, what is the minimum number of channels of DFB-LD required?
A) the wavelength tuning range A if it is operated between -20 °C and 80 °C is 10 nm
B) the minimum number of channels of DFB-LD required to span the entire C-band would be 4 channels.
(a) The change in oscillation wavelength according to the temperature of DFB-LD is +0.1 nm/°C.
Assuming that wavelength tuning is performed due to the temperature change of TEC, what is the wavelength tuning range A if it is operated between -20 °C and 80 °C?
The wavelength tuning range is determined by the minimum temperature of -20°C and the maximum temperature of 80°C, with a range of 100°C. For every degree of temperature increase, the oscillation wavelength increases by 0.1 nm.
The oscillation wavelength range can be found using the following equation:
A = Δλ/ΔT x ΔT
Where,
Δλ/ΔT = Temperature Coefficient of the device
ΔT = Change in temperature
A = Wavelength tuning range, we have,
Δλ/ΔT = +0.1 nm/°C
ΔT = (80 - (-20))°C = 100°C
So,
A = Δλ/ΔT x ΔT = +0.1 nm/°C x 100°C= 10 nm
(b) We intend to produce a tunable laser array that can use the entire C-band (1525 nm to 1565 nm) using multiple channels of DFB-LD with different center wavelengths. If the temperature range of the TEC is operated between -20 °C and 80 °C, what is the minimum number of channels of DFB-LD required?
To span the entire C-band (1525 nm to 1565 nm), we need to find the range of center wavelengths that is required. We can find this by finding the difference between the maximum wavelength of the C-band and the minimum wavelength of the C-band, which is,
1565 nm - 1525 nm = 40 nm
We know that for every degree of temperature increase, the oscillation wavelength increases by 0.1 nm. So, to span a wavelength range of 40 nm, we need to change the temperature by:
40 nm / 0.1 nm/°C = 400°C
To cover this range, we have a temperature range of 80 - (-20) = 100°C available to us.
Therefore, the minimum number of channels required to cover the full C-band would be:
400°C / 100°C = 4 channels
Hence, the minimum number of channels of DFB-LD required to span the entire C-band would be 4 channels.
learn more about tunable laser array here:
https://brainly.com/question/17011884
#SPJ11
direct current, as shown in the figure, the average value of the magnetic field measured in the sides is 6.3G. What is the current in the wire? พ
We cannot directly calculate the current passing through the wire. We would need additional information such as the distance from the wire to calculate the current.
In order to find out the current in the wire, let's first understand the concept of magnetic field in direct current.Direct current is an electric current that flows in a constant direction.
The magnetic field produced by a straight wire carrying a direct current is in the form of concentric circles around the wire. The magnitude of this magnetic field is directly proportional to the current passing through the wire. This magnetic field can be measured using a magnetic field sensor.The average value of the magnetic field measured in the sides is 6.3G.
Therefore, using the formula for magnetic field due to a straight wire, we get:B = μ₀I/2πrwhere B is the magnetic field, μ₀ is the permeability of free space (4π x 10⁻⁷ T m/A), I is the current passing through the wire, and r is the distance from the wire.In this case, the distance from the wire is not given.
Therefore, we cannot directly calculate the current passing through the wire. We would need additional information such as the distance from the wire to calculate the current.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
. A ray of light travels in a glass and exits into the air. The critical angle of the glass-air interface is 39 ∘
. Select possible correct pairs of angles of incident and refraction. 2 The speed of red light in glass A is faster than in glass B. Which of the following is/are TRUE? A. The index of refraction of B is higher than A. B. The speed of light in A is lower than in the air. C. The frequency of the red light is the same in both glasses. 3. Which of the following statement is/are TRUE about the polarization of waves? A. Sound waves can exhibit a polarization effect. B. Polarization is an orientation of an oscillation. C. Radiowave cannot be polarized because it is invisible. 4. Which of the following optical phenomena causes the change in the wavelength of a wave? A. Reflection B. Refraction C. Diffraction 5. Unpolarised light of intensity, I o
passes through three polarisers as shown in FIGURE 2. The second and third polarizers are rotated at angles θ 1
and θ 2
relative to the vertical line. θ 2
is set to 80 ∘
. What is/are the possible values of θ 1
and I 2
? 6. Which of the following optical elements always produce a virtual image? A. Positive lens B. Diverging lens C. Convex mirror 7. FIGURE 3 shows a television receiver which consists of a dish and the signal collector on a house roof. It receives radio waves from a long-distance transmitter containing information about television programs. Which statement is/are TRUE about the receiver? A. The receiver applies the effect of wave reflection. B. The receiver acts as a lens to focus received radiowaves. C. The receiver changes the wavelength of the received radio waves. 8. Which of the following lens has a positive focal length? 9. An image has twice the magnification of its object and is located on the opposite side of the object. The possible optical element(s) which can produce the condition is/are A. positive lens. B. concave lens. C. concave mirror. 10. An object and a converging mirror are positioned with the labelled focal point, F, as shown in FIGURE 4. Which ray(s) come(s) from the object's tip? FIGURE 4 11. Farhan has a far point of 90 cm. Which of the following is TRUE about her? A. He can use a concave mirror to correct her vision. B. He could not sharply see an object beyond 90 cm from his eyes. C. He can use contact lenses with negative optical power to correct her vision.
2 A. The index of refraction of B is higher than A.B. The speed of light in A is lower than in the air.C.
The frequency of the red light is the same in both glasses. 3. B. Polarization is an orientation of an oscillation.4. B. Refraction 5. θ1 = 50°, I2 = Io/4.6. C. Convex mirror. 7. A. The receiver applies the effect of wave reflection. 8. Positive lens. 9. A. Positive lens.10. Ray 1 and Ray 3 come from the object's tip.
B. He could not sharply see an object beyond 90 cm from his eyes.Explanation:2. If the speed of light in A is faster than in B, then the index of refraction of A will be lower than in B. So, statement A is not true, statement B is true and the frequency of the red light will be the same in both glasses because the medium change does not affect the frequency of the light.3. Polarization is an orientation of an oscillation. It is a property of transverse waves, including electromagnetic waves such as light and radio waves.4. Refraction is the bending of light when it passes from one transparent medium to another transparent medium. When light travels through different mediums, the speed changes, and this changes the direction of light. This change in direction and speed is called refraction.5. The intensity of unpolarized light after passing through the first polarizer is Io/2 and after passing through the second polarizer, it becomes Io/4.
The final intensity of light depends on the angle between the two polarizers. The value of θ1 can be calculated using the formula, I2 = Io/4 cos²(θ1 - θ2).6. A convex mirror always produces a virtual image that is smaller than the object and appears closer to the mirror than the actual object.7. The signal collector on the house roof of a TV receiver works based on the reflection of radio waves. The curved dish acts as a reflector to focus the incoming radiowaves on the signal collector.8. A positive lens is a lens that converges incoming light rays and has a positive focal length. Convex lens is a positive lens.9. The magnification produced by a lens or mirror depends on the focal length of the element. Only positive lenses have positive focal lengths. So, a positive lens will produce twice the magnification of the object and will be located on the opposite side of the object.10. Ray 1 and Ray 3 come from the object's tip. Ray 1 is parallel to the principal axis of the mirror and after reflection from the mirror passes through the focal point F. Ray 3 passes through the focal point F before reflection from the mirror and becomes parallel to the principal axis of the mirror after reflection.11. Farhan has a far point of 90 cm. It means he cannot see a distant object beyond 90 cm from his eyes.
This means his eye's accommodation power is weak. To correct this condition, he can use concave lenses with negative optical power, not concave mirrors.
Learn more on index here:
brainly.in/question/54095030
#SPJ11
A brick with a mass of 10 kg and a volume of 0.01 m³ is submerged in a fluid that has a density of 800 kg/m³. The brick will sink in the fluid. O True O False
The brick will sink in the fluid is true.
A brick with a mass of 10 kg and a volume of 0.01 m³ is submerged in a fluid that has a density of 800 kg/m³.
The density of an object is the ratio of mass to volume.
The mass of the brick is 10 kg and the volume is 0.01 m³.
So, the density of the brick is; Density = mass/volume = 10 kg/0.01 m³ = 1000 kg/m³
The density of the brick is 1000 kg/m³.
The density of the fluid is 800 kg/m³.
So, the brick will sink because the density of the brick is greater than the density of the fluid.
Learn more about sink: https://brainly.com/question/857846
#SPJ11