find y'' (second derivetive) of the function
y= cos(2x)/3−2sin^2(x)​
and find the inflection point

1) The atomic radius of Nickel is: 0.52 µm

2) The atomic mass is 195 g/mol and radius is 139 pm and the element is Platinum(Pt))

1) The formula to calculate the atomic radius of nickel is expressed as:

Density = nM/(V*NA)

Where:

n is number of atoms per unit cell (4 for FCC)

M is atomic mass = 59 a m u

V is volume of the unit cell = a³

NA is avogadro's number = 6.02 * 10²³

6.84 = (4 * 59)/(a³ * 6.02 * 10²³)

a³ = (4 * 59)/(6.84 * 6.02 * 10²³)

a =  1.472 * 10⁻⁶ m

a = 1.472 µm

For FCC, a = 2√2r

Thus:

r = 1.472 µm/(2√2)

r = 0.52 µm

2) We are given:

a = 392 pm = 3.92 x 10⁻⁸ cm

ρ = 21.45 g/cm³

Thus:

V = (3.92 * 10⁻⁸)³

V = 6.024 * 10⁻²³ cm³

Thus:

21.45 = (4 * M)/(6.024 * 10⁻²³ * 6.02 * 10²³)

M = 195 g/mol

a = r√8

3.92 * 10⁻⁸ = r√8

r = 1.386 * 10⁻⁸cm = 139 pm

(Element with atomic mass 195 g/mol and radius = 139 pm (1.386x10⁻⁸cm) = Platinum(Pt)) = Platinum(Pt)

Read more about Atomic Radius at: https://brainly.com/question/15255548

#SPJ4

The cost of the minimum amount needed to construct the roof would be approximately $1256.

To calculate the cost of the minimum amount needed to construct the roof, we need to determine the surface area of the roof and then multiply it by the cost per square foot of the aluminum.

The roof of the hut can be approximated as a portion of a cylinder. The surface area of a cylinder can be calculated using the formula:

Surface Area = 2πrh + πr^2

Given that the diameter of the hut is 16 feet, the radius (r) is half of the diameter, which is 8 feet. The length of the hut is 48 feet.

Plugging these values into the formula, we get:

Surface Area = 2π(8)(48) + π(8)^2

Surface Area = 96π + 64π

Surface Area = 160π

Now, we need to multiply the surface area by the cost per square foot of aluminum, which is $2.50.

Cost = Surface Area * Cost per square foot

Cost = 160π * $2.50

To get an approximate numerical value, we can use the approximation π ≈ 3.14.

Cost = 160 * 3.14 * $2.50

Cost = $1256

Therefore, the cost of the minimum amount needed to construct the roof would be approximately $1256.

for such more question on cost

https://brainly.com/question/8993267

#SPJ8

The correct range for the graph is -5 ≤ x ≤ 2 and -2 ≤ y ≤ 3.

The correct range for the graph can be determined by identifying the minimum and maximum values for both the x and y coordinates of the points given.
Let's analyze the given segments:
1. The first segment goes from (-5, -2) to (0, -1).
  - The x-coordinate ranges from -5 to 0.
  - The y-coordinate ranges from -2 to -1.
2. The second segment goes from (0, -1) to (2, 3).
  - The x-coordinate ranges from 0 to 2.
  - The y-coordinate ranges from -1 to 3.
To find the overall range for the graph, we need to consider the combined range of both segments.
For the x-coordinate, the minimum value is -5 (from the first segment) and the maximum value is 2 (from the second segment). So, the correct range for the x-coordinate is -5 ≤ x ≤ 2.
For the y-coordinate, the minimum value is -2 (from the first segment) and the maximum value is 3 (from the second segment). So, the correct range for the y-coordinate is -2 ≤ y ≤ 3.
In summary:
- The x-coordinate ranges from -5 to 2.
- The y-coordinate ranges from -2 to 3.
This information provides the correct range for the graph.

For more such questions on range

https://brainly.com/question/28044915

#SPJ8

if water consumption increases in the future, the city may need to consider expanding or upgrading the treatment plant to meet the growing demand.

The current water consumption in the city is 10,000 m³/d (cubic meters per day), while the existing treatment plant has a design capacity of 18,500 m³/d. This means that the treatment plant is designed to handle a maximum of 18,500 m³ of water per day.

With the current water consumption of 10,000 m³/d, the treatment plant is operating below its maximum capacity. This is a good thing because it means that the treatment plant has enough capacity to meet the current water demand of the city.

If the water consumption increases in the future and exceeds the design capacity of the treatment plant, it may lead to water shortages or inadequate treatment of water. In such a scenario, the treatment plant may need to be upgraded or expanded to handle the increased water demand.

It's important for the city to monitor its water consumption and plan for future needs to ensure that there is enough capacity in the treatment plant to provide clean and safe water to its residents.

In summary, the current water consumption in the city is 10,000 m³/d, and the existing treatment plant has a design capacity of 18,500 m³/d. The treatment plant is currently operating below its maximum capacity, but if water consumption increases in the future, the city may need to consider expanding or upgrading the treatment plant to meet the growing demand.

Learn more about capacity from the link:

https://brainly.com/question/29707733

#SPJ11

The present water consumption is 10,000 m³/d, which is lower than the treatment plant's design capacity of 18,500 m³/d. This suggests that the treatment plant is currently able to meet the city's water demand.

However, future increases in water consumption may require further action to ensure sufficient supply.

The present water consumption in the city is 10,000 m³/d, while the existing treatment plant has a design capacity of 18,500 m³/d at maximum. This means that the current water consumption is less than the treatment plant's maximum capacity.

To understand the situation, we can compare the present water consumption to the design capacity. Currently, the city is consuming 10,000 m³ of water per day, which is less than the maximum capacity of the treatment plant. This indicates that the treatment plant is able to meet the current water demand of the city.

However, it is important to note that the treatment plant may reach its maximum capacity in the future if the water consumption increases. In that case, additional measures such as expanding the treatment plant's capacity or implementing water conservation initiatives may be necessary to meet the growing demand.

Learn more about water conservation:

https://brainly.com/question/30333660?referrer=searchResults

#SPJ11

Answer:

Let's assume the original shape was an equilateral triangle with vertices at (0,0), (1,2), (2,0).

After a translation 5 units right, the triangle's vertices will be at (5,0), (6,2), (7,0).

To explain, a translation is a transformation which moves a shape's location without rotating, reflecting, or resizing it. In this case, since the shape was translated 5 units right, each vertex moved 5 units right from its original position, so (0,0) became (5,0), (1,2) became (6,2), and (2,0) became (7,0).

Step-by-step explanation:

The correct answer is D. d = C / Cr. This means that the diameter, d, is equal to the circumference, C, divided by the product of C and r.

To solve the equation Crd for d, we need to isolate d on one side of the equation.

Given that C = Crd, we can divide both sides of the equation by Cr to obtain:

C / Cr = Crd / Cr

Simplifying the right side:

C / Cr = d

Therefore, the equation Crd for d simplifies to:

d = C / Cr

D is the right response because d = C / Cr. As a result, the circumference, C, divided by the sum of C and r's product equals the diameter, d.

for such more question on diameter

https://brainly.com/question/28700310

#SPJ8

Given equation:

x + 2 = −3x + 11

We can set up  x + 2 = -3x + 11 as a  system of equations by equating both sides by zero resulting in two equations.

The equations will be as followed:

x + 2 = 0 ............(1)

−3x + 11 = 0  ............(2)

Thus, x + 2 = −3x + 11 can be set up as a system of equations as x + 2 = 0 and −3x + 11 = 0.

The required general equation of plane II 3x - 4y + 12 + 0z + 4 = 0-3x - 4y + 16 = 0.The two lines L1 and L2 can be represented as follows:

L1: x = 3 - 3s, y = 5 - 4s,

z = 8L2:

x = -2 + 2t, y = -4 + 5t, z = t

To get the intersection point of these two lines, we equate x, y, and z separately.

Hence,

we have:

[tex]3 - 3s = -2 + 2t[/tex]

⇒ 3s + 2t

= 5...........(i)

[tex]5 - 4s = -4 + 5t[/tex]

⇒[tex]4s + 5t[/tex]

= 9...........(i)

8 = t...............................(iii)

We can then write the general equation of plane II as:

[tex]-3(x - 4) - 4(y + 1) + 0(z + 2) = 0[/tex]

Simplifying the above equation, we have:-

[tex]3x - 4y + 12 + 0z + 4 = 0-3x - 4y + 16 = 0,[/tex] w

hich is the required general equation of plane II.

To know more about represented visit:

https://brainly.com/question/31291728

#SPJ11

The unit contribution margin is calculated by subtracting the variable cost per unit from the selling price per unit. In this case, the unit contribution margin is $18.95, which represents the amount of revenue available to cover fixed costs and contribute to profit for each toy sold. Thus, the correct answer is option 4.

To calculate the unit contribution margin, we need to first understand the terms "variable cost" and "fixed cost." The variable cost refers to the cost that changes depending on the number of units produced, while the fixed cost remains constant regardless of the number of units produced.

In this case, the variable cost per toy is given as $11, and the total fixed costs for the month are $45,000.

The unit contribution margin can be calculated by subtracting the variable cost per unit from the selling price per unit. In this case, the selling price per toy is $29.95, and the variable cost per toy is $11.

Unit contribution margin = Selling price per toy - Variable cost per toy
Unit contribution margin = $29.95 - $11
Unit contribution margin = $18.95

Therefore, the unit contribution margin is $18.95 (option 4).

Learn more about Selling price at:

https://brainly.com/question/21297845

#SPJ11

When each peptide is treated with chymotrypsin, several products are formed: Asp, Lys, and Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys

The process of breaking the peptide bonds into smaller fragments by chymotrypsin is called hydrolysis. The peptide bonds between amino acid residues are broken by chymotrypsin during the hydrolysis process. Two primary proteolytic products are produced when a peptide is hydrolyzed by chymotrypsin. Amino acids and short peptides are among these products, which are produced by the cleavage of the peptide bond.

Thus, the products formed when each peptide is treated with chymotrypsin are given below:

1. Ile-Glu-Ile-Trp-Cys-Pro: When it is treated with chymotrypsin, the peptide bond between the amino acids Ile and Glu is hydrolyzed, resulting in two fragments: Ile-Glu and Ile-Trp-Cys-Pro. Then, the peptide bond between Ile and Glu is hydrolyzed, resulting in three fragments: Ile, Glu, and Ile-Trp-Cys-Pro.

2. Lys-Arg-Ser-Phe-His-Ala: When it is treated with chymotrypsin, the peptide bond between Lys and Arg is hydrolyzed, resulting in two fragments: Lys-Arg and Ser-Phe-His-Ala. Then, the peptide bond between Arg and Ser is hydrolyzed, resulting in three fragments: Lys, Arg, and Ser-Phe-His-Ala.

3. Asp-Lys-Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys: When it is treated with chymotrypsin, the peptide bond between the amino acids Lys and Trp is hydrolyzed, resulting in two fragments:

Asp and Lys-Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys. Then, the peptide bond between Lys and Trp is hydrolyzed, resulting in three fragments: Asp, Lys, and Trp-Glu-His-Glu-Ile-Leu-Tyr-Thr-Pro-Cys.

Hence, the above-mentioned products are formed when each peptide is treated with chymotrypsin.

Learn more about hydrolysis from the given link:

https://brainly.com/question/30457911

#SPJ11

The equation has no valid solution because it leads to a division by zero, resulting in an undefined expression.

To solve the equation, we need to find the value of x that satisfies the equation:

(x + 2)/(3(x - 3)) + (x + 1)/(3) = 0

To simplify the equation, we need to find a common denominator for the fractions. The common denominator is 3(x - 3):

[(x + 2)(x - 3)]/(3(x - 3)) + (x + 1)(x - 3)/(3(x - 3)) = 0

Expanding the numerators, we have:

[tex][(x^2 - x - 6) + (x^2 - 2x - 3)]/(3(x - 3)) = 0[/tex]

Combining like terms in the numerator, we get:

[tex](2x^2 - 3x - 9)/(3(x - 3)) = 0[/tex]

To solve for x, we set the numerator equal to zero:

[tex]2x^2 - 3x - 9 = 0[/tex]

This quadratic equation can be factored as:

(2x + 3)(x - 3) = 0

Setting each factor equal to zero, we get:

2x + 3 = 0 or x - 3 = 0

Solving each equation for x, we find:

2x = -3 or x = 3

Dividing both sides of the first equation by 2, we have:

x = -3/2

Therefore, the solutions to the equation are x = 3 and x = -3/2.

In the given options, the correct answer would be:

A. x = 7

None of the provided options matches the solutions obtained from solving the equation.

For similar question on equation.

https://brainly.com/question/29797709  

#SPJ8

The statements provided contain various information about non-metals and ceramics. Let's break down each statement and provide a clear explanation for each:

Statement 18: Ceramics can be crystalline, semi-crystalline, or amorphous.
- Ceramics are a type of non-metal material that are known for their high melting points and excellent heat resistance.
- Crystalline ceramics have a regular, ordered arrangement of atoms, which gives them a defined structure.
- Semi-crystalline ceramics have both ordered and disordered regions within their structure.
- Amorphous ceramics lack a well-defined atomic structure and have a more random arrangement of atoms.

Statement 19: Ceramics generally have a higher tensile strength than compression strength.
- Tensile strength refers to a material's ability to resist being pulled apart.
- Compression strength refers to a material's ability to withstand being squeezed together.
- In general, ceramics have stronger resistance to being pulled apart (tensile strength) compared to being squeezed together (compression strength). This is due to the nature of their atomic structure, which allows them to better withstand pulling forces.

Statement 20: Tempered glass is stronger than annealed glasses.
- Tempered glass is a type of glass that undergoes a special heating and cooling process to increase its strength.
- Annealed glass, on the other hand, is the standard form of glass that is cooled slowly to relieve internal stresses.
- Tempered glass is stronger than annealed glass because the heating and cooling process creates surface compression, making it more resistant to breakage.

Statement 21: Ceramics consist of ionic bonds or covalent bonds.
- Ceramics are typically composed of elements with high electronegativity differences, leading to the formation of ionic or covalent bonds.
- Ionic bonds involve the transfer of electrons from one atom to another, creating positive and negative ions that are held together by electrostatic forces.
- Covalent bonds involve the sharing of electrons between atoms, resulting in a strong bond.

Statement 22: Crystallized polyethylene (PE) is denser and stronger than amorphous PE.
- Polyethylene (PE) is a polymer commonly used in various applications.
- Crystallized polyethylene has a more ordered structure with regions of crystallinity, making it denser and stronger compared to amorphous polyethylene, which lacks this ordered structure.

Statement 23: Polymer stress relaxation is independent of temperature.
- Polymer stress relaxation refers to the reduction of stress in a polymer over time when subjected to a constant strain.
- The rate of stress relaxation in polymers is influenced by factors such as temperature, time, and molecular structure.
- However, the statement that polymer stress relaxation is independent of temperature is not accurate. Temperature plays a significant role in polymer behavior, affecting the rate of relaxation and the extent to which stress is relieved.

Statement 24: Elastomers do not have a glass transition temperature (Tg).
- Elastomers are a type of polymer that exhibit large elastic deformation when subjected to stress and return to their original shape when the stress is removed.
- Unlike some other types of polymers, elastomers do not have a distinct glass transition temperature (Tg). The lack of a Tg is due to the flexible nature of the polymer chains, which allows them to move more freely even at low temperatures.

Statement 25: A polydispersity index equal to 1 means that all molecular chains in a polymer are equally long.
- The polydispersity index (PDI) is a measure of the molecular weight distribution in a polymer sample.
- A PDI of 1 indicates a monodisperse polymer sample, where all the molecular chains have the same length.
- In contrast, a higher PDI value indicates a broader distribution of molecular chain lengths in the polymer sample.

Overall, ceramics can have different structures, ceramics generally have higher tensile strength, tempered glass is stronger than annealed glass, ceramics consist of ionic or covalent bonds, crystallized polyethylene is denser and stronger than amorphous polyethylene, polymer stress relaxation is influenced by temperature, elastomers lack a distinct glass transition temperature, and a polydispersity index of 1 means all molecular chains in a polymer are equally long.

To know more about Ceramics :

https://brainly.com/question/30509290

#SPJ11

Answer:

To find the endpoint we have to calculate the distance between the known midpoint to the known endpoint. To calculate the midpoint we add two points and divide them by 2.

The formula for midpoint = (x1 + x2)/2, (y1 + y2)/2.

Substituting in the two x-coordinates and two y-coordinates from the endpoints.

Putting it together,

The endpoint formula is:

(x a ,ya)= ((2xm−xb),(2ym−yb))

( x a , y a ) = ( ( 2 x m − x b ) , ( 2 y m − y b ) ).

The end of a line at a point that is equally distant from both ends, a time interval between an event's beginning and end.

The point on a graph or figure where the figure stops might be referred to as the endpoint. It can be the point joining the sides of a polygon (the vertex), the common endpoint of two rays making an angle, the two extreme points of a line segment, the one end of a ray.

To learn more about endpoints and midpoints:

Step-by-step explanation:

this is just an exaple

Answer:

Step-by-step explanation:

The solution to the inequality x > 8 or x < 4 can be expressed as the set of all real numbers except for the interval [4, 8].

The solution to the inequality x > 12 or x < 6 can be expressed as the set of all real numbers.

The solution to the inequality x > 16/3 or x < 8/3 can be expressed as the set of all real numbers.

The displacement vector of the airplane and the duration of the flight  indicates that the direction and speed of the airplane are;

B. About 5.7° west of north at approximately 502.5 mph

A displacement vector represents the change in location of an object.

The speed and direction of the airplane can be found from the resultant vector from point A to point C as follows;

A(20, 20), C(-30, 520)

The displacement vector from point A to point C is; C - A = (-30, 520) - (20, 20) = (-50, 500), which is the net displacement of the plane from 1 PM to 2 PM.

The direction of the plane, which is the angle between the y-axis and the displacement vector is; θ = arctan(50/500) ≈ 5.7°

The magnitude of the displacement, which is the distance is therefore;

Distance = √((-50)² + (500)²) ≈ 502.5 miles

The speed = Distance/time

The time of flight from 1 PM to 2 PM = 1 hour

Learn more on displacement vector here: https://brainly.com/question/13265155

#SPJ1

Answer:

145.5

Step-by-step explanation:

cuz y not

Answer:

Hi there!! Thank you for posting this question, as it helped me figure this out for myself as well!!

Step-by-step explanation:

Maybe this will help,

Let’s pretend the actual number is 100. So, what is 3% of 100?

That is correct, it is 3.

And again, let’s pretend the number in question is actually 50, what is 3% of 50? Well, sense 50 is half of 100 let’s assume 3% of 50 would become Half of the 3 from earlier, making 50’s 3%, 2.5.

Let’s add those together, 3 + 2.5 = 5.5.

Therefore, if you decreased 150 by 3% you would arrive at 144.5.

I hope this helps!! I know this is not a very convention way to figure this out but I hope this makes sense!! Have a blessed day!!

Using induction, does the following statement hold: 1.1+2 2!++n.n!= (n+1)!-1. The statement holds for all nonnegative integers n. The correct option is Yes.

The statement holds when using induction.

Induction:

Step 1: Basis Step

If n = 0, then the left-hand side of the equation is 1.1! = 1, and the right-hand side is (0+1)!-1 = 0, so the statement is true for n=0.

Step 2: Inductive Hypothesis

Suppose the statement is true for n=k, that is,1.1+2 2!+3 3!+...+k k! = (k+1)!-1 (1)

Step 3:  Inductive Step

We need to show that the statement is true for n=k+1. That is,1.1+2 2!+3 3!+...+(k+1) (k+1)! = [(k+1)+1]!-1(2)

To prove (2), we can add (k+1)(k+1)! to both sides of (1) to obtain1.1+2 2!+3 3!+...+k k!+(k+1)(k+1)! = (k+1)!-1+(k+1)(k+1)!

We can simplify the right-hand side using the distributive law, factoring out (k+1):= (k+2)!-1

The left-hand side is1.1+2 2!+3 3!+...+(k+1) (k+1)! =(k+1)!+(k+1)(k+1)! =(k+1)!(1+(k+1)) =(k+1)!(k+2)

Substituting the last two equations into (2) gives(k+1)!(k+2)-1 = (k+2)!-1

This is exactly the statement for n=k+1, so the inductive step is complete. Therefore, by the principle of mathematical induction, the statement holds for all nonnegative integers n. The correct option is Yes.

Learn more about nonnegative integers

https://brainly.com/question/10542824

#SPJ11

The capacity ratio method estimates the cost of expanding a clinic by 8,400 ft² by dividing the original facility's capacity by the new capacity. The new cost is approximately $23.314 million, reflecting larger facilities' lower per-unit costs and smaller facilities' higher costs.

To estimate the cost of expanding a planned new clinic by 8,400 ft², we can use the capacity ratio method.

Capacity Ratio Method: If the capacity of a facility changes by a factor of "C," the cost of the new facility will be "a" times the cost of the original facility, where "a" is the capacity exponent.

Capacity Ratio (C) = (New Capacity / Original Capacity)

New Cost = Original Cost x (Capacity Ratio)^Capacity Exponent

Given data:

Original Area = 185,000 ft²

New Area = 185,000 + 8,400 = 193,400 ft²

Capacity Ratio (C) = (193,400 / 185,000) = 1.0459

Capacity Exponent (a) = 0.62

Budget Estimate for 185,000 ft² = $19 million

New Cost = $19 million x (1.0459)^0.62= $19 million x 1.226= $23.314 million (approx)

Therefore, the estimated cost of expanding a planned new clinic by 8,400 ft² is $23.314 million (approx).

Note:In the capacity ratio method, the capacity exponent is used to adjust the cost estimate for a new facility to reflect the fact that larger facilities have lower per-unit costs, and smaller facilities have higher per-unit costs.

To know more about capacity ratio Visit:

https://brainly.com/question/14643660

#SPJ11

The test used to determine the specific gravity for a soil sample is called the hydrometer test.

In the calculation of percent finer for soil classification using the hydrometer test, the readings should be corrected for meniscus and temperature corrections.

Hydrometer test measures the density of the soil sample compared to the density of water. The specific gravity of a soil sample is an important property that helps in soil classification and engineering calculations.

In the hydrometer test, a soil-water suspension is prepared by mixing the soil sample with water. The mixture is then allowed to settle, and the hydrometer is used to measure the settling velocity of the soil particles. By measuring the settling velocity, the specific gravity of the soil sample can be determined.

Now, moving on to the second question about the correction of readings in the hydrometer test for soil classification. When conducting the hydrometer test, two types of corrections need to be made to the readings: meniscus correction and temperature correction.

The meniscus correction accounts for the curvature of the water surface in the hydrometer. The reading on the hydrometer should be taken at the bottom of the meniscus curve, where the curve intersects the hydrometer scale.

The temperature correction is necessary because the density of water changes with temperature. The readings obtained from the hydrometer test should be corrected based on the temperature of the water used in the test.

Therefore, in the calculation of percent finer for soil classification using the hydrometer test, the readings should be corrected for both meniscus and temperature corrections. These corrections ensure accurate results and reliable soil classification.

Learn more about specific gravity here: https://brainly.com/question/20422535

#SPJ11

The value of k when f(x) = 2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, is K = 45.

To determine the value of k when f(x)=2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, we can use the Remainder Theorem.

According to the Remainder Theorem, when a polynomial f(x) is divided by a linear factor x-a, the remainder is equal to f(a). In this case, the linear factor is x-3 and the remainder is 2.

So, to find the value of k, we substitute x=3 into the polynomial f(x) and set it equal to 2:

f(3) = 2(3)¹ - 5(3)³ + K(3) - 4 = 2

Now, let's solve for k:

2(3) - 5(3)³ + 3K - 4 = 2
6 - 135 + 3K - 4 = 2
-133 + 3K = 2

To isolate K, we add 133 to both sides:

3K = 2+ 133
3K = 135

Finally, divide both sides by 3 to solve for K:

K = 45

Learn more about remainder :

https://brainly.com/question/27749132

#SPJ11

The order of processing requests and the total movement for each disk scheduling algorithm are as follows:

(1) SSTE: 133, 131, 85, 125, 1470, 913, 948, 1022, 1509, 1750, 1764. Total movement = 2929 tracks.

(2) SCAN: 133, 1470, 1764, 1750, 1509, 948, 913, 1022, 131, 85, 125. Total movement = 4639 tracks.

(3) C-SCAN: 133, 1764, 1750, 1509, 1022, 948, 913, 85, 131, 125, 1470. Total movement = 5423 tracks.

In the SSTE (Shortest Seek Time First) algorithm, the request with the minimum seek time from the current head position is processed next. Starting from track 133, the order of processing the requests is 85, 133, 125, 1470, 913, 948, 1022, 1509, 1750, 1764, and 131. The total movement is calculated by summing up the absolute differences between consecutive tracks.

In the SCAN algorithm, the disk arm starts at one end of the disk and moves towards the other end, servicing requests along the way. After reaching the other end, the head movement is reversed, and servicing continues. In this case, the order of processing the requests is 85, 133, 1764, 1750, 1509, 948, 913, 131, 125, 1022, and 1470. The total movement is calculated similarly to SSTE.

The C-SCAN (Circular SCAN) algorithm treats the cylinders as a circular list and moves from one end to the other, servicing requests. However, when reaching the other end, it immediately returns to the beginning of the disk without servicing any requests on the return trip. The order of processing the requests using C-SCAN is 85, 133, 913, 948, 1022, 1470, 1509, 1750, 1764, 125, and 131. The total movement is calculated accordingly.

These disk scheduling algorithms aim to minimize the movement of the disk arm and optimize the efficiency of processing requests based on their locations on the disk.

Learn more about algorithm here:

https://brainly.com/question/21172316

#SPJ11

Answer:

(a)  P(Blue) = 0.24

     P(Green) = 0.12

(b)  176

Step-by-step explanation:

Let x be the probability that the spinner lands on green.

Given the spinner is twice as likely to land on blue than green, the probability of it landing on blue is 2x.

The sum of all probabilities must equal 1, so we can set up the equation:

[tex]0.2 + 2x + x + 0.44 = 1[/tex]

Solve the equation for x:

[tex]\begin{aligned}0.2 + 2x + x + 0.44 &= 1\\3x+0.64&=1\\3x+0.64-0.64&=1-0.64\\3x&=0.36\\3x\div3&=0.36\div3\\x&=0.12\end{aligned}[/tex]

Therefore, the probability of landing on green is 0.12, and the probability of landing on blue is 0.24.

[tex]\begin{array}{|c|c|c|c|c|}\cline{1-5}\vphantom{\dfrac12} \sf Colour& \sf Red& \sf Blue& \sf Green& \sf Yellow\\\cline{1-5}\vphantom{\dfrac12} \sf Probability & 0.2 & 0.24 & 0.12 & 0.44\\\cline{1-5}\end{array}[/tex]

[tex]\hrulefill[/tex]

The expected number of times the spinner is expected to land on yellow can be calculated by multiplying the probability of landing on yellow by the total number of spins:

[tex]\begin{aligned}\textsf{Expected number of yellow spins}&=\textsf{Probability of yellow} \times\textsf{Total number of spins}\\&= 0.44 \times 400\\&= 176\end{aligned}[/tex]

Therefore, the spinner is expected to land on yellow 176 times out of 400 spins.

The calculated probabilities of the spinner are:

(a)  P(Blue) = 0.24 and P(Green) = 0.12

(b)  176

We are given the probabilities as:

P(Red) = 0.2

P(yellow) = 0.44

Let z be the probability that the spinner lands on green.

We are told that the spinner is twice as likely to land on blue than green, and as such it means that the probability of it landing on blue is 2z

The sum of all probabilities must equal 1, so we can set up the equation:

0.2 + 2z + z + 0.44 = 1

3z + 0.64 = 1

3z = 1 - 0.64

3z = 0.36

z = 0.12

2z = 2 * 0.12 = 0.24

b) If spinner is spun 400 times, then:

N(yellow) = 0.44 * 400 = 176

Read more about Probability of spinner at: https://brainly.com/question/3765462

#SPJ1

The series ln(1) is divergent as it approaches negative infinity.

The series ln(1) can be expressed as a telescoping sum using the property ln(a) - ln(b) = ln(a/b).

By applying this property, we rewrite the series as ln(1) = ln(1) - ln(1/2) + ln(2) - ln(2/3) + ln(3) - ln(3/4) + ...

Each term cancels out with the next term, except for the first and last terms.

Simplifying, we get ln(1) - ln(1/∞). As the limit of 1/∞ approaches 0, ln(1/∞) approaches negative infinity. Therefore, the series ln(1) is divergent, meaning it does not converge to a finite value.

The provided explanation explains why the series ln(1) is divergent by expressing it as a telescoping sum and using the property of logarithms.

It clarifies that each term cancels out, except for the first and last terms, and demonstrates how the limit of 1/∞ approaches 0, resulting in negative infinity.

To learn more about logarithms click here

brainly.com/question/30226560

#SPJ11

The general solutions to the given ODEs are as follows:

a. y = C₁e^(t)sin(2t) + C₂e^(t)cos(2t)

b. y = C₁e^(t) + C₂e^(-t)

c. y = C₁e^(3t) + C₂e^(-t)

d. y = C₁e^(√5t)sin(t) + C₂e^(√5t)cos(t)

a. The given ODE is a second-order linear homogeneous differential equation with constant coefficients. To solve it, we assume a solution of the form y = e^(rt). Plugging this into the equation, we get the characteristic equation r^2 - 2r + 9 = 0. Solving this quadratic equation, we find two distinct roots: r = 1 ± 2i. Using the complex exponential form, we can rewrite the general solution as y = e^(t)(C₁sin(2t) + C₂cos(2t)).

b. This ODE is also a second-order linear homogeneous differential equation with constant coefficients. Assuming a solution of the form y = e^(rt) and plugging it into the equation, we obtain the characteristic equation r^2 - 1 = 0. The roots are r = ±1. Therefore, the general solution is y = C₁e^(t) + C₂e^(-t).

c. Similarly, this ODE is a second-order linear homogeneous differential equation with constant coefficients. By assuming y = e^(rt) and substituting it into the equation, we obtain the characteristic equation r^2 - 4r + 1 = 0. Solving this equation, we find two distinct roots: r = 3, -1. Hence, the general solution is y = C₁e^(3t) + C₂e^(-t).

d. This ODE is a second-order linear homogeneous differential equation with variable coefficients. Assuming y = e^(rt) and substituting it into the equation, we obtain the characteristic equation r^2 - 2√5r + 5 = 0. Solving this equation, we find two complex conjugate roots: r = √5i, -√5i. Using the complex exponential form, the general solution can be written as y = e^(√5t)(C₁sin(t) + C₂cos(t)).

Step 3:

In each of the given ODEs, we used the method of assuming a solution of the form y = e^(rt) and then solving for the roots of the characteristic equation. By plugging in these roots into the general solution, we obtain the complete solution that satisfies the ODE. These general solutions can be verified by substituting them back into the original ODEs and confirming that they satisfy the equations. The substitution process involves differentiating y and plugging it into the ODE to see if the equation holds true. Upon verification, it can be concluded that the obtained solutions are indeed the general solutions to the given ODEs.

Learn more about: Constant coefficients

brainly.com/question/28973882

#SPJ11

1. Four common corrections to a measurement made by a steel tape are:

a) Temperature correction

b) Pull correction

c) Sag correction

d) Alignment correction

Temperature correction: The answer to temperature correction is that steel tapes expand or contract as the temperature changes and this change affects the accuracy of measurements. Therefore, temperature correction is done to compensate for the effect of the change of temperature.

Pulling correction: In order to get accurate measurements, the tape is always tensioned to an even pull or load while taking measurements. The main answer to pulling correction is that pulling a tape with too much force or with not enough force affects the measurement.

Sag correction: The main answer to sag correction is that the weight of the tape makes it bend and this affects the measurement. Therefore, sag correction is used to determine the amount of deviation caused by the weight of the tape.

Alignment correction: The main answer to alignment correction is that when measuring long distances, it is difficult to keep the tape straight which causes an error. Therefore, alignment correction is done to correct for these errors.2. The distance from an IP (initial point) to the NE can be found by using the bearing and distance. The main answer to this is that the bearing tells us the direction of the point we are measuring to and the distance gives us the length of the line from the IP to the NE.

To find the distance from the IP to the NE, we use the formula; Distance = Length × Cos Bearing Angle

Thus, Distance = 10,000 × Cos 25°. Therefore, the distance from the IP to the NE is 9,160 feet (approx).

Learn more about sag correction: https://brainly.com/question/33590303

#SPJ11

Poorly-graded gravel or gravel mixed with sand provides poor to fair strength and characteristics while its potential to frost action is excellent and drainage is high.

Poorly-graded gravel or gravel mixed with sand typically has a wide range of particle sizes, resulting in a less compacted and stable material. This leads to its poor to fair strength and characteristics. However, when it comes to frost action, poorly-graded gravel or gravel mixed with sand performs excellently. The varying particle sizes allow for better drainage and reduced water accumulation, minimizing the potential for frost heave and damage caused by freezing and thawing cycles. Additionally, the drainage capability of poorly-graded gravel or gravel mixed with sand is very low. The presence of different-sized particles creates void spaces that enhance water movement through the material, promoting effective drainage and preventing waterlogging.

Poorly-graded gravel or gravel mixed with sand exhibits poor to fair strength and characteristics, excellent resistance to frost action, and very low drainage capability.

To know more about gravel visit:

https://brainly.com/question/28855557

#SPJ11

The balanced reduction half-reaction for the given oxidation-reduction reaction under basic conditions is: Cu(OH)₂ + 2e⁻ → Cu + 2OH⁻, where copper is reduced by gaining two electrons.

To write the balanced reduction half-reaction for the given oxidation-reduction reaction under basic conditions, we need to balance both the atoms and charges. The half-reaction represents the reduction process, where electrons are gained.

The reaction given is:

Cu(OH)₂ + F₂ → Cu + F⁻

First, let's identify the elements that are undergoing oxidation and reduction. In this case, copper (Cu) is being reduced, as it goes from a higher oxidation state of +2 in Cu(OH)₂ to 0 in Cu. Fluorine (F) is being oxidized, as it goes from 0 in F₂ to -1 in F⁻.

To balance the reduction half-reaction, we need to balance the charge by adding electrons (e⁻). The number of electrons should be equal to the change in oxidation state of the element being reduced. In this case, copper is gaining two electrons.

Thus, the balanced reduction half-reaction is:

Cu(OH)₂ + 2e⁻ → Cu + 2OH⁻

This indicates that copper hydroxide (Cu(OH)₂) is reduced to copper (Cu), with the gain of two electrons, and hydroxide ions (OH⁻) are also produced.

To learn more about electrons visit:

https://brainly.com/question/860094

#SPJ11