Find the Value of x so that l || m. State the converse used. (PLEASE HELP ASAP!!)

The factor of safety with respect to shear failure for the strip footing is approximately 0.049 when φ' = 0° and cu = 105 kN/m² is 0.049 and it is approximately 2.78 when φ' = 28° and cu = 10 kN/m² is 2.78.

The factor of safety with respect to shear failure for the given strip footing can be determined as follows:

(a) When cu = 105 kN/m² and φ' = 0:

The effective stress at the base of the footing can be calculated using the formula: qnet = q - γw ×  d, where q is the applied load, γw is the unit weight of water, and d is the depth of the footing. In this case, qnet = 430 - (21 ×  1) = 409 kN/m². The ultimate bearing capacity of the clay can be determined using Terzaghi's equation: qult = cNc + qNq + 0.5γBNγ, where c is the cohesion, Nc, Nq, and Nγ are bearing capacity factors, and γB is the bulk unit weight of the soil. For φ' = 0°, Nc = 5.4. Substituting the given values,

qult = (0 ×  5.4) + (409 ×  0) + (0.5 × 21 ×  2) = 21 kN/m²

The factor of safety (FS) is then calculated by dividing the ultimate bearing capacity by the applied load:

FS = qult / q = 21 / 430 ≈ 0.049.

(b) When cu = 10 kN/m² and φ' = 28°:

Using the given values of φ' = 28°, we can determine the bearing capacity factors from the provided data:

Nc = 26, Nq = 15, and Nγ = 13.

Substituting these values along with the net pressure

qnet = 430 - (21 × 1) = 409 kN/m² and the cohesion c = 10 kN/m² into Terzaghi's equatio× , we have

qult = (10 ×  26) + (409 ×  15) + (0.5 ×  21 ×  2 ×  13) = 1,197 kN/m²

The factor of safety is then calculated as FS = qult / q = 1,197 / 430 ≈ 2.78.

To learn more about shear refer:

https://brainly.com/question/2973519

#SPJ11

(a) The factor of safety against shear failure when cu=105 kN/m² and ø'=0 is 1.

(b) The factor of safety against shear failure when cu=10 kN/m² and ø'=-28° is 0.004.

The factor of safety with respect to shear failure for a strip footing carrying a load of 430 kN/m can be determined as follows:

(a) When cu=105 kN/m² and ø'=0:

The factor of safety (FS) can be calculated as:

[tex]\[ FS = \frac{cu}{\gamma \times N_c \times B \times N_q} \][/tex]

Substituting the given values: cu=105 kN/m², γ=21 kN/m³, B=2 m, and Nc=5, we have:

[tex]\[ FS = \frac{105 \, \text{kN/m}^2}{21 {kN/m^2} \times 5 \times 2 \, \text{m}} = 1 \][/tex]

(b) When cu=10 kN/m² and ø'=-28°:

The factor of safety (FS) can be calculated as:

[tex]\[ FS = \frac{cu}{\gamma \times N_c \times B \times N_q} \][/tex]

Substituting the given values: cu=10 kN/m², γ=21 kN/m³, B=2 m, Nc=26, and Nq=15, we have:

[tex]\[ FS = \frac{10 \, {kN/m}^2}{21 \, {kN/m^3} \times 26 \times 2 \, \text{m} \times 15} = 0.004 \][/tex]

To learn more about shear refer:

https://brainly.com/question/30464657

#SPJ11

The femoral stem of a hip implant is most likely to suffer from abrasive wear.

The femoral stem of a hip implant is likely to suffer Abrasive wear. Abrasive wear refers to the loss of material from the surface of a solid body by the motion of a harder material across this surface. The material loss is caused by the hard abrasive particles such as bone cement debris or particles from the surface of the implant.

Abrasive wear occurs due to friction, scratching, or rubbing. In a hip implant, this occurs when the femoral stem is rubbing against the acetabular cup, or in other words, the ball of the femoral stem rubs against the hip socket. The high forces generated during normal hip joint movement lead to this type of wear.

The type of wear that affects the femoral stem of a hip implant can cause damage to the implant over time, leading to implant failure. Some of the common factors that can lead to abrasive wear include implant misalignment, improper material selection, or the use of the implant beyond its recommended lifespan.

For more question on  hip implant:

brainly.com/question/15262227

#SPJ11

The skeletal structure of 1-butene is: The skeletal structure of 1-butene is as follows: There are four carbon atoms in 1-butene. Therefore, it has four electrons.

The first and last carbon atoms are triple-bonded, whereas the middle two carbon atoms are single-bonded to one another. The condensed structural formula of 1-chlorobutane from the Lewis structure is:

The following is the Lewis structure for 1-chlorobutane As a result, the condensed structural formula for 1-chlorobutane from the Lewis structure is: CH3CH2CH(Cl)CH3. There are four carbon atoms in 1-butene. Therefore, it has four electrons.

To know more about skeletal structure visit :

https://brainly.com/question/33447095

#SPJ11

An ideal Diesel engine operating with an air temperature of 20°C and a compression ratio of 15, reaching a maximum temperature of 2000°C, produces a net work of approximately 789.24 kJ/mole.

We can determine the net work produced by an ideal Diesel engine by using the following steps:

1. Calculate the initial temperature in Kelvin:

T₁ = 20°C + 273.15

   = 293.15 K.

2. Calculate the final temperature in Kelvin:

T₃ = 2000°C + 273.15

    = 2273.15 K.

3. Use the compression ratio to calculate the intermediate temperature, T₂:

  T₂ = T₁ * (compression ratio)^(ɣ-1)

       = 293.15 K * (15)^(1.4-1)

       = 973.28 K.

4. Calculate the pressure at point 2 using the ideal gas law:

  P₂ = P₁ * (T₂/T₁)^(ɣ)

      = 90 kPa * (973.28 K/293.15 K)^(1.4)

      = 1,494.95 kPa.

5. Calculate the net work produced per mole using the formula:

  Net Work = Cp * (T₃ - T₂) - Cp * (T₃ - T₂)/ɣ

                   = 1.005 kJ/kg.K * (2273.15 K - 973.28 K) - 1.005 kJ/kg.K * (2273.15 K - 973.28 K)/1.4

                   ≈ 789.24 kJ/mole.

Therefore, the net work produced by the ideal Diesel engine is approximately 789.24 kJ/mole.

Learn more About temperatures from the given link

https://brainly.com/question/27944554

#SPJ11

The pressure profile at the wellbore can be represented as follows:

1. Drawdown phase: During the 600 hours of production, the pressure at the wellbore decreases from the initial reservoir pressure of 7000 psi to 6200 psi. This is due to the flow of oil from the reservoir to the wellbore. The pressure decreases gradually over time.

2. Buildup phase: After the production phase, a buildup test is conducted for 500 hours. During this phase, the pressure at the wellbore starts to increase. At the end of the test, the average pressure is 6950 psi. This increase in pressure is caused by the accumulation of fluid in the reservoir and the decrease in the flow rate.

The pressure profile can be represented graphically as a plot of pressure against time. The graph will show a gradual decrease in pressure during the production phase and a subsequent increase during the buildup phase. The important features to label on the graph include the initial reservoir pressure, the pressure at the end of the drawdown test, and the average pressure at the end of the test. These labels will help to visualize the changes in pressure over time.

In summary, the pressure profile at the wellbore consists of a drawdown phase where the pressure decreases during production, followed by a buildup phase where the pressure increases during the buildup test. The graph of the pressure profile should include labels for the initial reservoir pressure, the pressure at the end of the drawdown test, and the average pressure at the end of the test.

Know more about pressure profile here:

https://brainly.com/question/30361837

#SPJ11

the value of 't' in the equation is 1/6.

The  equation is:

2(6t - 2) + 3(7 - 2t) = 18

We will simplify and solve the equation as follows;

12t - 4 + 21 - 6t = 18 Simplify the brackets 6t + 17 = 18

Add like terms-17 = 18 - 6t Rearrange the equation and solve for

t. -17 = - 6t + 18-17 - 18 = - 6t -35 = -6t

Divide both sides of the equation by -6 t = 35/6Solving the equation:

2(6t - 2) + 3(7 - 2t) = 18

We can find the value of 't' by simplifying and solving the given equation. We simplified the equation by distributing the factors and combining like terms.

We get12t - 4 + 21 - 6t = 18

Simplifying the equation, we combine the like terms as;6t + 17 = 18 Rearranging the terms in the equation,

we get; 6t = 18 - 17 t = (18 - 17)/6 Simplifying further, we gett = 1/6

For more question equation

https://brainly.com/question/29419919

#SPJ8

Hello!

x + 3 = y²  ☑

y = x² - 3 ☑

x + y = 3²

y = x + 3² ☑

Answer:

x + 3 = y^2

Step-by-step explanation:

x + 3 = y^2 is not a fnction

The graph of this is a parabola which opens to the rigth so it fails the vertical line test.  ( a vertical line can be drawn to pass throgh 2 points on the graph)

The maximum likelihood estimate (MLE) of c, is 60.732 kPa.

Linear method:

Posterior distribution of c, can be determined using the Bayes' Theorem as follows:

Step 1: Determine prior distribution P(c)As given, c follows a normal distribution with mean (µ) = 60 kPa and standard deviation (σ) = 20 kPa.

Therefore, P(c) can be represented as follows:

P(c) = (1/√2πσ) exp(-(c - µ)²/2σ²)P(c) = (1/√2π*20) exp(-(c - 60)²/2*20²)

Step 2: Determine likelihood function P(q|c)

The ultimate pressure that an undrained ground can support is given by q = 5.14c₂.

Therefore, P(q|c) can be given by:

P(q|c) = (1/√2πσ) exp(-(q - 5.14c₂)²/2σ²)

P(q|c) = (1/√2π*10) exp(-(300 - 5.14c)²/2*10²)

Step 3: Determine posterior distribution P(c|q)

Using Bayes' Theorem, the posterior distribution of c, can be determined as:

P(c|q) = P(q|c) * P(c) / P(q)

Where P(q) is the probability of getting the measured value of q, irrespective of the value of c. It can be given by the following expression:

P(q) = ∫ P(q|c) * P(c) dc

By substituting the values in the above expressions, we get:

P(c|q) = (1/√2π*10) exp(-(300 - 5.14c)²/2*10²) * (1/√2π*20) exp(-(c - 60)²/2*20²) / ∫ (1/√2π*10) exp(-(300 - 5.14c)²/2*10²) * (1/√2π*20) exp(-(c - 60)²/2*20²) dc

Solving the above expression, we get the posterior distribution of c as:

P(c|q) = (1/√2πσp) exp(-(c - µp)²/2σp²)

Where µp = 65.509 kPa and σp = 17.845 kPa

Nonlinear method: Posterior distribution of c, can also be determined using the nonlinear method as follows:

Using Bayes' Theorem, we can write:

P(c|q) = P(q|c) * P(c) / P(q)

Where, P(q|c) is the likelihood function which is given by:

P(q|c) = 5.14c + ε

Where ε is the measurement error which follows a normal distribution with mean (µε) = 0 and standard deviation (σε) = 10 kPa.

Therefore, ε can be represented as:ε = (q - 5.14c) + ξ

Where ξ is a normally distributed random variable with mean (µξ) = 0 and standard deviation (σξ) = 10 kPa.

Therefore, ξ can be represented as:

ξ = ε - (q - 5.14c)

Substituting the values of ε and ξ, we get:

P(q|c) = (1/√2πσε) exp(-(q - 5.14c)²/2σε²) * exp(-ξ²/2σξ²)

By substituting the above expression in the Bayes' Theorem expression, we get:

P(c|q) = (1/√2πσεp) exp(-(q - 5.14c)²/2σεp²) * exp(-(c - µ)²/2σ²)

Where µ = 60 kPa, σ = 20 kPa, σεp = 8.057 kPa, and the maximum likelihood estimate (MLE) of c, is 60.732 kPa.

To know more about expressions visit:

https://brainly.com/question/28170201

#SPJ11

The inverse Laplace transform of 8/(s + 2)² is [tex]8te^{(-2t)}[/tex]

The solution y(t) to the given initial value problem is:

[tex]y(t) = 1 - 2e^{(-2t)} + 8te^{(-2t)[/tex]

To solve the given initial value problem using Laplace transforms, we will first take the Laplace transform of both sides of the differential equation.

Then we will solve for the Laplace transform of the unknown function Y(s).

Finally, we will take the inverse Laplace transform to obtain the solution in the time domain.

The Laplace transform of the second derivative y" of a function y(t) is given by:

[tex]L\{y"\} = s^2Y(s) - sy(0) - y'(0)[/tex]

The Laplace transform of the first derivative y' of a function y(t) is given by:

[tex]L\{y'\} = sY(s) - y(0)[/tex]

The Laplace transform of a constant multiplied by a unit step function u_a(t) is given by:

[tex]L\{c * u_a(t)\} = (c / s) * e^_(-as)[/tex]

Applying these transforms to the given differential equation:

[tex]L\{y"+4y'+5y\} = L\{2u_3(t)-u_4(t)\} - t[/tex]

[tex]s^2Y(s) - sy(0) - y'(0) + 4(sY(s) - y(0)) + 5Y(s) = 2/s * e^{\{(-3s)\}} - 1/s * e^{(-4s)} - (1 / s^2)[/tex]

Using the initial conditions y(0) = 0 and y'(0) = 4:

[tex]s^2Y(s) - 4s + 4sY(s) + 5Y(s) =[/tex] [tex]2/s * e^{(-3s)} - 1/s * e^{(-4s)} - (1 / s^2)[/tex]

Combining like terms:

[tex]Y(s)(s^2 + 4s + 5) = 2/s * e^{(-3s)} - 1/s * e^{(-4s)} - (1 / s^2) + 4s[/tex]

Factoring the quadratic term:

[tex]Y(s)(s + 2)^2 = 2/s * e^(-3s) - 1/s * e^{(-4s)} - (1 / s^2) + 4s[/tex]

Now, solving for Y(s):

[tex]Y(s) = [2/s * e^{(-3s)} - 1/s * e^{(-4s)} - (1 / s^2) + 4s] / [(s + 2)^2][/tex]

To find the inverse Laplace transform of Y(s), we will use partial fraction decomposition.

The expression [tex](s + 2)^2[/tex] can be written as (s + 2)(s + 2) or (s + 2)².

Let's perform partial fraction decomposition on Y(s):

[tex]Y(s) = [2/s * e^{(-3s)} - 1/s * e^{(-4s)} - (1 / s^2) + 4s] / [(s + 2)^2] = A/s + B/(s + 2) + C/(s + 2)^2[/tex]

Multiplying through by the common denominator (s²(s + 2)²):

[tex]2(s + 2)^2 - s(s + 2) - (s + 2)^2 + 4s(s + 2)^2 = As(s + 2)^2 + Bs^2(s + 2) + Cs^2[/tex]

Simplifying the equation:

[tex]2(s^2 + 4s + 4) - s^2 - 2s - s^2 - 4s - 4 - s^2 - 4s - 4 = As^3 + 4As^2 + 4As + Bs^3 + 2Bs^2 + Cs^2[/tex]

[tex]2s^2 + 8s + 8 - 3s^2 - 10s - 4 = (A + B)s^3 + (4A + 2B + C)s^2 + (4A)s[/tex]

Grouping the terms:

[tex]-s^3 + (A + B)s^3 + (4A + 2B + C)s^2 + (4A + 2B - 2)s = 0[/tex]

Comparing the coefficients of like powers of s, we get the following equations:

1 - A = 0          (Coefficient of s³ term)

4A + 2B + C = 0    (Coefficient of s² term)

4A + 2B - 2 = 0    (Coefficient of s term)

Solving these equations, we find:

A = 1

B = -2

C = 8

Substituting these values back into the partial fraction decomposition:

Y(s) = 1/s - 2/(s + 2) + 8/(s + 2)²

Now we can take the inverse Laplace transform of Y(s) using the table of Laplace transforms:

[tex]L^{-1}{Y(s)} = L^{-1}{1/s} - L^{-1}{2/(s + 2)} + L^{-1}{8/(s + 2)^2}[/tex]

The inverse Laplace transform of 1/s is simply 1. The inverse Laplace transform of,

[tex]2/(s + 2)\ is\ 2e^{(-2t)[/tex]

The inverse Laplace transform of 8/(s + 2)² is [tex]8te^{(-2t)}[/tex]

Therefore, the solution y(t) to the given initial value problem is:

[tex]y(t) = 1 - 2e^{(-2t)} + 8te^{(-2t)[/tex]
To know more about Laplace transforms visit:

https://brainly.com/question/30759963

#SPJ11

The initial value problem involves a second-order linear homogeneous differential equation with discontinuous forcing functions. The differential equation is given by y"+4y'+5y=2u₃(t)-u₄(t) t, where y(0) = 0 and y'(0) = 4.

To solve this problem using Laplace transforms, we take the Laplace transform of both sides of the equation, apply the initial conditions, solve for the Laplace transform of y(t), and finally take the inverse Laplace transform to obtain the solution in the time domain.

Using the Laplace transform, the given differential equation becomes

(s²Y(s) - sy(0) - y'(0)) + 4(sY(s) - y(0)) + 5Y(s) = 2e^(-3s)/s - e^(-4s)/s².

Substituting the initial conditions, we have

(s²Y(s) - 4s) + 4(sY(s)) + 5Y(s) = 2e^(-3s)/s - e^(-4s)/s².

Simplifying the equation, we get

Y(s) = (4s + 4)/(s² + 4s + 5) + (2e^(-3s)/s - e^(-4s)/s²)/(s² + 4s + 5).

To find the inverse Laplace transform, we can use partial fraction decomposition and inverse Laplace transform tables. The inverse Laplace transform of Y(s) will yield the solution y(t) in the time domain. Due to the complexity of the equation, the explicit form of the solution cannot be determined without further calculations.

Therefore, by applying Laplace transforms and solving the resulting algebraic equation, we can obtain the solution y(t) to the initial value problem with discontinuous forcing functions.

To learn more about differential equation refer:

https://brainly.com/question/18760518

#SPJ11

The bearing capacity of the soil at a depth of 6ft below the bottom of the corner of the foundation is option B) 120

Given that the size of a square foot with th of 3 feet is placed on the ground surface.

The structural loads are expected to be approximately 9 lips.

Uutes and we are required to find A (psf) at a depth equal to 6 ft below the bottom of the corner of the foundation.Therefore, we have to determine the weight of soil above a 6 ft by 6 ft column of soil underneath the foundation. We can use the following formula for this purpose:

A = W / (L × W)

where A is the bearing capacity of the soil in psf,

W is the weight of soil above the 6 ft by 6 ft column of soil underneath the foundation in pounds,

and L is the length of the column (6 ft).

W = V × γ

where V is the volume of soil in the 6 ft by 6 ft column underneath the foundation

(6 ft × 6 ft × 6 ft) and γ is the unit weight of soil (given as 120 pcf).

W = 6 ft × 6 ft × 6 ft × 120

pcf = 259,200 pounds

A = W / (L × W) = 259,200 pounds / (6 ft × 6 ft) = 1,200 psf

Now, we have determined the bearing capacity of the soil at 0 ft depth (i.e., the surface).

The bearing capacity at 6 ft below the surface is given by:

Qu = qNc + 0.5γBNq + 0.5γDNγ

where q, Nc, B, Nq, and D are determined from soil tests.

Since these values are not provided, we can make use of the Terzaghi and Peck (1948) bearing capacity factors to estimate the value of

Qu/qa:Qu/qa = 2.44 × (Df / B) × Nc + 0.67 × Nq + 1.33 × (Df / B) × B/Df × Nγ

where Df is the depth of the foundation (i.e., 6 ft), and B is the width of the foundation (i.e., 6 ft).Nc, Nq, and Nγ are bearing capacity factors that are determined from soil tests.

If we assume that the soil is medium-dense sand (a common type of soil), we can use the following values for these factors:

Nc = 35, Nq = 20, Nγ = 16

Substituting these values in the formula, we get:

Qu/qa = 2.44 × (6 ft / 6 ft) × 35 + 0.67 × 20 + 1.33 × (6 ft / 6 ft) × 16

= 167 psf

Therefore, the correct option is (b) 120.

To know more about capacity visit :

brainly.com/question/33301627

#SPJ11

From the question;

1) The concentration is 0.037 M

2) The activation energy is 23.96 kJ/mol

The rate of reaction is the speed at which a chemical reaction takes place. Over a given period of time, it measures the rate at which reactants are converted into products.

We know that rate of reaction is defined by;

Rate = Δ[A]/ Δt

Rate = 0.555 - 0.333/500 - 200

= 0.0007 M/s

Now;

0.0007=  0.555 - x/1000 - 200

0.0007 = 0.555 - x/800

x = 0.037 M

The activation energy can be obtained from;

ln([tex]k_{2}[/tex]/[tex]k_{1}[/tex]) = -Ea/R(1/[tex]T_{2}[/tex] - 1/[tex]T_{1}[/tex])

ln(0.004/0.001) = - Ea/8.314(1/348 - 1/298)

1.39 = 0.000058 Ea

Ea = 23.96 kJ/mol

Learn more about rate of reaction: https://brainly.com/question/13693578

#SPJ4

a) The concentration of H₂ is 0, the pH of the solution is undefined. b) The concentration of H₂ is 0, so the pH of the solution is undefined.

To calculate the pH of the solution after the addition of NaH solution, we need to consider the reaction between NO and NaH, and the resulting change in concentration of the species.

The reaction between NO and NaH is as follows:

NO + NaH → NaNO + H₂

Given:

Initial concentration of NO = 0.08 M

Initial volume of NO solution = 30 ml

Concentration of NaH = 0.10 M

Volume of NaH solution added = 12 ml (for part a) and 24 ml (for part b)

K value for the reaction = 4.57 x 10⁴

a) After adding 12.0 ml of NaH solution:

To calculate the final concentration of NO, we need to consider the stoichiometry of the reaction. For every 1 mole of NO reacted, 1 mole of NaNO is formed.

Initial moles of NO = Initial concentration of NO * Initial volume of NO solution

= 0.08 M * (30 ml / 1000)

= 0.0024 moles

Moles of NO reacted = Moles of NaNO formed = 0.0024 moles

Final moles of NO = Initial moles of NO - Moles of NO reacted

= 0.0024 moles - 0.0024 moles

= 0 moles

Final volume of the solution = Initial volume of NO solution + Volume of NaH solution added

= 30 ml + 12 ml

= 42 ml

Final concentration of NO = Final moles of NO / Final volume of the solution

= 0 moles / (42 ml / 1000)

= 0 M

Now, we can calculate the pH using the equilibrium expression for NO:

K = [NaNO] / [NO] * [H₂]

Since the concentration of NO is 0, the equilibrium expression simplifies to:

K = [NaNO] / [H₂]

[H₂] = [NaNO] / K

= 0 / 4.57 x 10⁴

= 0

As the concentration of H₂ is 0, the pH of the solution is undefined.

b) After adding 24.0 ml of NaH solution:

Using the same calculations as in part a), we find that the final concentration of NO is 0 M and the final volume of the solution is 54 ml.

Following the same equilibrium expression, we have:

K = [NaNO] / [H₂]

[H₂] = [NaNO] / K

= 0 / 4.57 x 10⁴

= 0

Again, the concentration of H2 is 0, so the pH of the solution is undefined.

In both cases, the pH of the solution after the addition of NaH solution is undefined due to the absence of H2 in the reaction and solution.

To know more about concentration:

https://brainly.com/question/31906648

#SPJ4

The final forces (magnitude and tension/compression) in each member are as follows:

[tex]AG: `5/13`*AB,[/tex]Tension

AB: 8.31 kN,

mpression BC: `5/13`*AB, Tension

BG: `5/13`*AB*2/√3, Compression

FG: 2.6 kN, Compression

CG: `5/13`*AB, TensionExtra points:

Calculation of CF:Let's consider the joint at C.

Given truss structure is as follows: Calculation: Let's first calculate the value of P2.P2=2P1=2(3)=6 kN

Member AG:As we see, member AG is a vertical member. Let's find the vertical component of force in it. Let's assume tension forces are positive and compression forces are negative in our calculations.

Since the node at A is in equilibrium, therefore the vertical force in member AG will be equal to the vertical component of force in member AB.`5/13`*AB - AG*sin(30º) = 0`5/13`*AB - AG*0.5 = 0AG = `5/13`*AB ...(1)

Now, let's consider the joint at G. Again, as joint G is in equilibrium, therefore the vertical force in member AG will be equal to the vertical component of force in member BG.AG*sin(30º) - BG*sin(60º) = 0BG = AG*2/√3 ...(2)

Putting (1) in (2) we get: [tex]BG = `5/13`*AB*2/√3[/tex]Member AB:

Let's consider the joint at A and find the horizontal component of force in member[tex]AB.`5/13`*AB*cos(30º) + AB*cos(60º) = P2AB = P2/[`5/13`*cos(30º) + cos(60º)][/tex]

Putting P2 = 6 kN, we get

AB = 8.31 kN

Therefore,

C

As joint C is in equilibrium, the force in member CF will be equal in magnitude and opposite in direction to the force in member BC.FC = BC = `5/13`*AB

Hence, the load CF is `5/13`*AB.

To know more about Compression visit:

https://brainly.com/question/32332232

#SPJ11

We have shown that 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2 holds for all n > 0.To prove by induction that for all integers n ≥ 2, 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2 - 1/n, we will follow these steps:

1. Base case:
  - For n = 2, we have 1 + 1/22 = 1 + 1/4 = 5/4 < 2 - 1/2 = 3/2. This is true.
 
2. Inductive hypothesis:
  - Assume that for some k ≥ 2, 1 + 1/22 + 1/32 + ⋯ + 1/k2 < 2 - 1/k.
 
3. Inductive step:
  - We need to prove that 1 + 1/22 + 1/32 + ⋯ + 1/k2 + 1/(k+1)2 < 2 - 1/(k+1).
  - Adding 1/(k+1)2 to both sides of the inequality in the hypothesis, we have:
    1 + 1/22 + 1/32 + ⋯ + 1/k2 + 1/(k+1)2 < 2 - 1/k + 1/(k+1)2.
  - Simplifying the right side, we have:
    2 - 1/k + 1/(k+1)2 = 2 - (1/k - 1/(k+1)2).
  - To prove our statement, we need to show that (1/k - 1/(k+1)2) > 0.
  - Expanding (1/k - 1/(k+1)2), we get:
    1/k - 1/(k+1)2 = [(k+1)2 - k]/[k(k+1)2].
  - Simplifying, we have:
    [(k+1)2 - k]/[k(k+1)2] = [k2 + 2k + 1 - k]/[k(k+1)2] = (k2 + k + 1)/[k(k+1)2].
  - Since k ≥ 2, we have k(k+1)2 > 0. Thus, (k2 + k + 1)/[k(k+1)2] > 0.
  - Therefore, 1 + 1/22 + 1/32 + ⋯ + 1/k2 + 1/(k+1)2 < 2 - (1/k - 1/(k+1)2) = 2 - 0 = 2.

By using the principle of mathematical induction, we have proved that for all integers n ≥ 2, 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2 - 1/n.

To prove that 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2 holds for all n > 0, we can use the result we just proved by induction.

For n = 1, we have 1 < 2, which is true.

For n ≥ 2, we know that 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2 - 1/n. Since 2 - 1/n > 1, we can conclude that 1 + 1/22 + 1/32 + ⋯ + 1/n2 < 2.

To know more about statement visit:

https://brainly.com/question/32562440

#SPJ11

The equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is 0.0097 M.

The balanced equation for the ionization of citric acid is;

C6H8O7(aq) + 3H2O(l) ⇌ C6H5O7-(aq) + H3O+(aq) + 2H2O(l)K_a = 7.5 × 10^-4
Explanation: ICE Table can be defined as an Initial, Change and Equilibrium table. This table is used to calculate the concentration of products and reactants in a chemical reaction at equilibrium. This method is used to calculate the equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M. Let's begin by writing the balanced equation of the ionization of citric acid is;

C6H8O7(aq) + 3H2O(l) ⇌ C6H5O7-(aq) + H3O+(aq) + 2H2O(l)K_a

= 7.5 × 10^-4

The ICE table is; Initial Equilibrium ChangeC6H8O7 (aq) 0.35 M 0 M - x M3H2O (l) 0 0 + 3x MC6H5O7- (aq) 0  x MH3O+ (aq) 0  x M2H2O (l) 0 0 + 2x M

The equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is x. Thus the equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is 0.0097 M.

To know more about equilibrium visit:

brainly.com/question/33361891

#SPJ11

The equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is 0.0097 M.

The balanced equation for the ionization of citric acid is;

C6H8O7(aq) + 3H2O(l) ⇌ C6H5O7-(aq) + H3O+(aq) + 2H2O(l)K_a = 7.5 × [tex]10^{-4[/tex]

Explanation: ICE Table can be defined as an Initial, Change and Equilibrium table. This table is used to calculate the concentration of products and reactants in a chemical reaction at equilibrium. This method is used to calculate the equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M. Let's begin by writing the balanced equation of the ionization of citric acid is;

C6H8O7(aq) + 3H2O(l) ⇌ C6H5O7-(aq) + H3O+(aq) + 2H2O(l)K_a

= 7.5 × [tex]10^{-4[/tex]

The ICE table is; Initial Equilibrium ChangeC6H8O7 (aq) 0.35 M 0 M - x M3H2O (l) 0 0 + 3x MC6H5O7- (aq) 0  x MH3O+ (aq) 0  x M2H2O (l) 0 0 + 2x M

The equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is x. Thus the equilibrium concentration of H+ (aq) for citric acid (C6H8O7) at an initial concentration of 0.35 M is 0.0097 M.

To know more about equilibrium visit:

brainly.com/question/33361891

#SPJ11

The performance of a ten-storey building using nonlinear static analysis in TAPS (Targeted Acceptable Performance Spectrum), you would typically follow these steps:

Model Creation: Create a detailed structural model of the ten-storey building in a structural analysis software that supports nonlinear static analysis, such as SAP2000, ETABS, or OpenSees. The model should include the geometry, material properties, and structural elements (columns, beams, slabs, etc.).

Define Loading: Define the design loading for the building based on the relevant design codes and standards. This may include dead loads, live loads, wind loads, and seismic loads. For nonlinear static analysis, you typically apply a pushover load pattern.

Pushover Analysis: Perform a nonlinear static pushover analysis on the structural model. This analysis method involves incrementally increasing the applied load until the structure reaches its maximum capacity or a predetermined limit state. The analysis determines the lateral load-displacement response of the building.

It's important to note that the specific procedures and parameters for conducting a nonlinear static analysis in TAPS may vary depending on the software you are using and the requirements of the project.

Therefore, it is recommended to refer to the software documentation, relevant design codes, and seek guidance from experienced structural engineers to ensure accurate and reliable performance evaluation.

To more about nonlinear, visit:

https://brainly.com/question/2030026

#SPJ11

A racetrack is in the shape of an ellipse, 170 feet long and 80 feet wide. What is the width 10 feet from a vertex.The width 10 feet from a vertex of the racetrack is approximately 39.7228 feet.

To find the width 10 feet from a vertex of the racetrack, we need to determine the value of the minor axis at that point.

An ellipse has two axes: the major axis (the longer one) and the minor axis (the shorter one). In this case, the major axis is the length of the racetrack, which is 170 feet, and the minor axis is the width of the racetrack, which is 80 feet.

The general equation for an ellipse centered at the origin is:

x^2/a^2 + y^2/b^2 = 1

Where 'a' represents the semi-major axis and 'b' represents the semi-minor axis.

In this case, the semi-major axis is 170/2 = 85 feet (half of the length), and the semi-minor axis is 80/2 = 40 feet (half of the width).

Now, we can solve for the width 10 feet from a vertex. Let's assume we are measuring from the positive x-axis (right side of the racetrack):

When x = 10, we can rearrange the equation to solve for y:

y = b × (1 - (x^2/a^2))

Plugging in the values:

y = 40 ×\sqrt{(1 - (10^2/85^2))}

y = 40 ×\sqrt{(1 - (10^2/85^2))}

y = 40 ×\sqrt{ (1 - 0.01381)}

y = 40 × \sqrt{(0.98619)}

y ≈ 40 × 0.99307

y ≈ 39.7228 feet

Therefore, the width 10 feet from a vertex of the racetrack is approximately 39.7228 feet.

To learn more about ellipse visit: https://brainly.com/question/9702250

#SPJ11

The value of (f(x) × g(x))′ at x=c is 104.

The value of (f(x) × g(x))′ at x=c can be found by applying the product rule of differentiation.

According to the product rule, if we have two functions f(x) and g(x), then the derivative of their product is given by the formula:

(f(x) × g(x))′ = f′(x) × g(x) + f(x) × g′(x)

Given that f(c) = -5, f′(c) = 13, and g′(c) = 13, we can substitute these values into the formula to find the value of (f(x) × g(x))′ at x=c.

Substituting the given values into the formula, we have:

(f(x) × g(x))′ = f′(x) × g(x) + f(x) × g′(x)

(f(x) × g(x))′ = 13 × g(x) + (-5) × 13

(f(x) × g(x))′ = 13g(x) - 65

Since we are interested in the value at x=c, we substitute c into the expression:

(f(x) × g(x))′ = 13g(c) - 65

Finally, substituting the value of g′(c) = 13, we have:

(f(x) × g(x))′ = 13 × 13 - 65

(f(x) × g(x))′ = 169 - 65

(f(x) × g(x))′ = 104

Therefore, the value of (f(x) × g(x))′ at x=c is 104.

Learn more about derivative from the given link

https://brainly.com/question/28376218

#SPJ11  

The final pressure of the nitrogen gas sample is approximately 6.2 atm.

To find the final pressure, we can use the combined gas law, which states that the product of the initial pressure and initial volume divided by the initial temperature is equal to the product of the final pressure and final volume divided by the final temperature.

Let's denote the initial pressure as P1, the initial volume as V1, the initial temperature as T1, and the final pressure as P2. We are given that P1 = 4.6 atm, V1 decreases by 55%, T1 = -21.0 °C, and the final temperature is 25.0 °C.

First, we need to convert the temperatures to Kelvin by adding 273.15 to each temperature: T1 = 252.15 K and T2 = 298.15 K.

Next, we can substitute the given values into the combined gas law equation:

(P1 * V1) / T1 = (P2 * V2) / T2

Since V1 decreases by 55%, V2 = (1 - 0.55) * V1 = 0.45 * V1.

Now we can solve for P2:

(4.6 atm * V1) / 252.15 K = (P2 * 0.45 * V1) / 298.15 K

Cross-multiplying and simplifying:

4.6 * 298.15 = P2 * 0.45 * 252.15

1367.39 = 113.47 * P2

Dividing both sides by 113.47:

P2 ≈ 12.06 atm

However, we need to round the answer to the correct number of significant digits, which is determined by the given values. Since the initial pressure is given with two significant digits, we round the final pressure to two significant digits:

P2 ≈ 6.2 atm

Therefore, the final pressure of the nitrogen gas sample is approximately 6.2 atm.

Know more about combined gas law here:

https://brainly.com/question/30458409

#SPJ11

We can now determine the ultimate moment capacity of the rectangular beam. =[tex]0.36′(−0.42) or = 0.36′(−0.5[/tex])

Ultimate moment capacity, Mu =[tex]0.36 × 28 × (804 × 414 × 10⁻⁶) × (435 - 0.5 × 206.3) / 10⁶= 338.56 kN.m[/tex]

Number of bars, n = 24Spacing, s = 250 / 24 = 10.42 mm

Therefore, the required rebar spacing for the top column strip is 10.42mm (Answer).

a. Rectangular beam design The data provided for the rectangular beam design are as follows; Width, B = 300mmEffective depth, d = 435mm Concrete cover, c = 50mmPc = 28MPaFy = 414MPa

Main reinforcement, 4-Φ16mm bars; Ast = 804mm² and 2-Φ20mm bars; Ast = 1018mm²First, let's calculate the maximum possible reinforcement ratio of the rectangular beam.ρ_max[tex]= 0.85 × (2/3) × (Fy/Pc)ρ_max = 0.85 × (2/3) × (414/28)ρ_max = 0.0489 or 4.89%[/tex]

Let's calculate the actual reinforcement ratio; Ast / bdAst = 804 + 1018 = 1822mm²Actual reinforcement ratio, [tex]ρ_t = Ast / bdρ_t = (1822 / 300 × 435)ρ_t = 0.014 or 1.4%[/tex]

We can now calculate the actual compression block depth, [tex]"a".a = c + (d/2) × (1 - √(1 - ((4.6 × ρ_t) / ρ_max)))a = 50 + (435/2) × (1 - √(1 - ((4.6 × 0.014) / 0.0489)))a = 206.3[/tex] mm

The actual compression block depth is 206.3mm.. This is the ultimate moment capacity of the beam.

To know more about spacing visit:

https://brainly.com/question/19596114

#SPJ11

Answer:

Step-by-step explanation:

If y varies directly as x, it means that the ratio of y to x remains constant. We can express this relationship using the equation:

y = kx

where k is the constant of variation.

Given that y is 180 when x is n, we can write:

180 = kn

Similarly, when y is n, x is 5:

n = k(5)

To find the value of n, we can equate the two expressions for k:

kn = k(5)

Dividing both sides by k (assuming k ≠ 0):

n = 5

Therefore, the value of n is 5.

The urbanization affects the receiving water in the following ways: Rainwater cannot infiltrate the soil in urban areas because of the high degree of impervious surface coverage and the absence of a cohesive soil structure.

As a result, the majority of the precipitation flows directly into surface waters, leading to an increase in the volume and rate of flow in the drainage basin.A lack of vegetation and trees results in increased stormwater runoff, which can cause more flooding and erosion, as well as increased water temperature due to the absence of shade. As a result, higher water temperatures can cause a decrease in the amount of oxygen in the water, causing harm to fish and other aquatic organisms.Heavy metals, hydrocarbons, pesticides, and other pollutants are found in urban runoff due to the presence of impervious surfaces and human activities. These pollutants can cause harm to aquatic life and reduce the water quality.

Conventional drainage systems that are separate work as follows:The sanitary sewers collect wastewater from homes and other structures, while the storm sewers collect rainwater and snowmelt. Each set of pipes transports water to separate treatment facilities. The wastewater treatment plant receives sewage and other types of wastewater from sanitary sewers. These treatment facilities purify the water to make it safe to discharge into rivers, lakes, or oceans. The stormwater drainage systems in cities frequently do not get treated before they enter the receiving waters.The major drawback of using separate conventional drainage systems is that they transport huge volumes of polluted stormwater runoff, which pollutes rivers, streams, and other aquatic habitats. They also transport pollutants that accumulate on streets and other impervious surfaces during dry periods when little or no rainfall is present.

To know more about cohesive visit:

https://brainly.com/question/31934169

#SPJ11

The  W is a subspace of R ²n spanned by n nonzero orthogonal vectors statement is true.

Proof:

Let W be a subspace ofR²n spanned by n nonzero orthogonal vectors. To prove that W = R²n,  to show that any vector x ∈ R²n can be expressed as a linear combination of the orthogonal vectors that span W.

Since W is spanned by n nonzero orthogonal vectors, let's denote them as v-1, v-2, ..., v-n.

Now, consider an arbitrary vector x ∈ R²n. We can express x as a linear combination of the orthogonal vectors:

x = c-1v-1 + c-2v-2 + ... + c-nv-n,

where c-1, c-2, ..., c-n are scalars.

Since the vectors v-1, v-2, ..., v-n are orthogonal, their dot products with each other are zero:

v-i · v-j = 0, for all i ≠ j.

Take the dot product of both sides of the equation with the vectors v_i:

v-i · x = v-i · (c-1v-1 + c-2v-2 + ... + c-nv-n).

Using the distributive property of the dot product, we have:

v-i · x = c-1(v-i · v-1) + c-2(v-i · v-2) + ... + c-i(v-i · v-i) + ... + c-n(v-i · v-n).

Since the vectors v-i are orthogonal, the dot products v-i · v-j are zero for i ≠ j. Thus, the equation simplifies to:

v-i · x = c-i(v-i · v-i).

Since v-i · v-i is the squared norm (magnitude) of v-i, denoted as ||v-i||²,

v-i · x = c-i × ||v-i||².

Solving for c-i, we get:

c-i = (v-i · x) / ||v-i||².

Substituting this back into the equation for x, we have:

x = (v-1 · x / ||v-1||²) × v-1 + (v-2 · x / ||v-2||²) × v-2 + ... + (v-n · x / ||v-n||²) × v-n.

This shows that any vector x ∈ R²n can be expressed as a linear combination of the orthogonal vectors v-1, v-2, ..., v-n. Therefore, W = R²n.

Hence, the statement is true, and we have provided a proof.

To know more about vectors here

https://brainly.com/question/24256726

#SPJ4

Therefore, the area of the triangle with side lengths a = 17 m, b = 9 m, and c = 18 m is 75.621 m². The answer is more than 100 words.

The given side lengths are a = 17 m, b = 9 m, and c = 18 m.

To find the area of the triangle, we can use the Heron's formula which states that the area of a triangle whose sides are a, b, and c is given by:`

s = (a + b + c)/2`

where s is the semi-perimeter of the triangle.`

Area = sqrt(s(s-a)(s-b)(s-c))`

Substituting the values of a, b, and c, we get:

s = (17 + 9 + 18)/2

= 22

We can now use the formula to find the area of the triangle.

Area = `sqrt(22(22-17)(22-9)(22-18))`

= `sqrt(22 × 5 × 13 × 4)`

= `sqrt(22 × 260)`

= `sqrt(5720)`= 75.621 m²

Therefore, the area of the triangle with side lengths a = 17 m, b = 9 m, and c = 18 m is 75.621 m². The answer is more than 100 words.

To know more about triangle visit;

brainly.com/question/2773823

#SPJ11

The angle of the surface tension film that leaves the glass for the vertical tube immersed in water is approximately 36.86 degrees.

To compute the angle of the surface tension film that leaves the glass for a vertical tube immersed in water, we can use the formula:
θ = 2 * arcsin(h / d)
Where:
θ is the angle of the surface tension film
h is the capillary rise
d is the diameter of the tube

The diameter (d) is 0.25 in and the capillary rise (h) is 0.08 inches, we can substitute these values into the formula:
θ = 2 * arcsin(0.08 / 0.25)
Now, we need to evaluate the expression inside the arcsin function:
0.08 / 0.25 = 0.32

So, the expression becomes:
θ = 2 * arcsin(0.32)

To calculate the value of arcsin(0.32), we can use a scientific calculator or lookup table. In this case, the value of arcsin(0.32) is approximately 18.43 degrees.
Now, we can substitute this value back into the formula:
θ = 2 * 18.43
θ = 36.86 degrees

You can learn more about surface tension at: brainly.com/question/571207

#SPJ11

The value of the obligation on October 1, 2018, would be approximately $4590.77.

To calculate the value of the obligation on October 1, 2018, we need to discount the debt amount of $4875.03 back to that date using an annual interest rate of 2% compounded annually.

The formula to calculate the present value of a future amount is:

Present Value = Future Value / (1 + r)^n

- Future Value is the debt amount due on October 1, 2021, which is $4875.03.

- r is the annual interest rate, given as 2% or 0.02 as a decimal.

- n is the number of years between October 1, 2021, and October 1, 2018, which is 3 years.

Substituting the values into the formula:

Present Value = $4875.03 / (1 + 0.02)^3

Calculating the present value:

Present Value = $4875.03 / (1.02)^3

Present Value = $4875.03 / 1.061208

Present Value ≈ $4590.77

Thus, the appropriate answer is approximately $4590.77.

Learn more about debt:

https://brainly.com/question/28929846

#SPJ11

The solution when the triangle is solved for c is 96 degrees

From the question, we have the following parameters that can be used in our computation:

The triangle

The third angle in the triangle is calculated as

Third = 180 - 60 - 24

So, we have

Third = 96

By the theorem of corresponding angles, we have

c = Third

This means that

c = 96

Hence, the triangle solved for c is 96 degrees

Read more about angles at

https://brainly.com/question/31898235

#SPJ1

The crystal field theory explains how ligands affect the energy levels of the metal's d orbitals. In this case, the dx2.yz orbital experiences an increase in energy due to repulsion from the ligands, while the dxy orbital remains unaffected

According to the crystal field theory, the ligands interact with the metal ion in a coordination complex. These interactions affect the energy levels of the metal's d orbitals. In the case of the dx2.yz orbital, the ligands' approach causes repulsion along the z-axis, which increases its energy. However, the dxy orbital does not experience this type of repulsion and therefore its energy remains unchanged.

To understand this, imagine the metal ion at the center, with ligands surrounding it. The dx2.yz orbital is oriented along the z-axis, so when the ligands approach, the electron density is concentrated in this direction. This causes repulsion between the ligands and the electron cloud in the dx2.yz orbital, leading to an increase in energy.

On the other hand, the dxy orbital lies in the xy-plane, perpendicular to the z-axis. Since the ligands approach from the z-direction, there is no direct interaction between the ligands and the electron cloud in the dxy orbital. As a result, the energy of the dxy orbital remains unchanged.

learn more about crystal field

https://brainly.com/question/29805362

#SPJ11

The claim is false. There is no value of 'a' that would make the line y = 2 + 3x the best least-square fit for the given data.

To determine if the line y = 2 + 3x is the best least-square fit for the data, we need to minimize the sum of squared residuals between the observed y-values and the predicted y-values based on the line. The sum of squared residuals (SSR) can be calculated using the formula:

SSR = Σ(y - (2 + 3x)) ²

Let's calculate the SSR for the given data points:

For (1.0, 4.0):

SSR = (4.0 - (2 + 3(1.0)))^2 = 1.0

For (2.0, 9.0):

SSR = (9.0 - (2 + 3(2.0))) ² = 4.0

For (3.0, a):

SSR = (a - (2 + 3(3.0))) ²= (a - 11)^2

The total SSR is the sum of the individual SSRs:

Total SSR = 1.0 + 4.0 + (a - 11) ²

To find the best fit, we need to minimize this total SSR. However, the value of 'a' does not affect the first two terms of the total SSR, and changing 'a' will only change the third term. Therefore, it is not possible to find a value of 'a' that minimizes the total SSR and makes the line y = 2 + 3x the best fit for the given data.

Learn more about Least-squares fit

brainly.com/question/28974320

#SPJ11

the molecular formulas corresponding to the given empirical formulas and molecular masses are:

1) C12H12O2

2) C8H16O4

3) C6H12O2

4) C32H24O6

To find the molecular formulas corresponding to the given empirical formulas and molecular masses, we need to determine the multiple of the empirical formula that gives the correct molecular mass.

1) Empirical formula: C6H6O

  Molecular mass: 204.93 g/mol

  The empirical formula mass can be calculated as follows:

  Empirical formula mass = (6 * Atomic mass of C) + (6 * Atomic mass of H) + (1 * Atomic mass of O)

                        = (6 * 12.01 g/mol) + (6 * 1.01 g/mol) + (1 * 16.00 g/mol)

                        = 72.06 g/mol + 6.06 g/mol + 16.00 g/mol

                        = 94.12 g/mol

  To find the multiple, we divide the molecular mass by the empirical formula mass:

  Multiple = Molecular mass / Empirical formula mass

           = 204.93 g/mol / 94.12 g/mol

           ≈ 2.18

  Rounding to the nearest whole number, the molecular formula is:

  Molecular formula = (C6H6O)2 ≈ C12H12O2

2) Empirical formula: C4H8O2

  Molecular mass: 159.69 g/mol

  Empirical formula mass = (4 * Atomic mass of C) + (8 * Atomic mass of H) + (2 * Atomic mass of O)

                        = (4 * 12.01 g/mol) + (8 * 1.01 g/mol) + (2 * 16.00 g/mol)

                        = 48.04 g/mol + 8.08 g/mol + 32.00 g/mol

                        = 88.12 g/mol

  Multiple = Molecular mass / Empirical formula mass

           = 159.69 g/mol / 88.12 g/mol

           ≈ 1.81

  Rounding to the nearest whole number, the molecular formula is:

  Molecular formula = (C4H8O2)2 ≈ C8H16O4

3) Empirical formula: C3H6O

  Molecular mass: 90.03 g/mol

  Empirical formula mass = (3 * Atomic mass of C) + (6 * Atomic mass of H) + (1 * Atomic mass of O)

                        = (3 * 12.01 g/mol) + (6 * 1.01 g/mol) + (1 * 16.00 g/mol)

                        = 36.03 g/mol + 6.06 g/mol + 16.00 g/mol

                        = 58.09 g/mol

  Multiple = Molecular mass / Empirical formula mass

           = 90.03 g/mol / 58.09 g/mol

           ≈ 1.55

  Rounding to the nearest whole number, the molecular formula is:

  Molecular formula = (C3H6O)2 ≈ C6H12O2

4) Empirical formula: C16H12O3

  Molecular mass: 389.42 g/mol

  Empirical formula mass = (16 * Atomic mass of C) + (12 * Atomic mass of H) + (3 * Atomic mass of O)

                        = (16 * 12.01 g/mol) + (12 * 1.01 g/mol) + (3 * 16.00 g/mol)

                        = 192.16 g/mol + 12.12 g/mol + 48.00 g/mol

                        = 252.28 g/mol

  Multiple = Molecular mass / Empirical formula mass

           = 389.42 g/mol / 252.28 g/mol

           ≈ 1.54

  Rounding to the nearest whole number, the molecular formula is:

  Molecular formula = (C16H12O3)2 ≈ C32H24O6

To know more about molecular visit:

brainly.com/question/30640129

#SPJ11