This indicates that the equilibrium state of the reaction—also referred to as an unfavourable equilibrium—favors the reactants.
The reaction mechanism might be one explanation for this. Reactants may build up before the equilibrium state is reached if the reaction has a slow step. The reaction's stoichiometry, in which the ratio of products to reactants is not ideal for product formation, may also be a factor.
Reactant concentrations can be lowered or product concentrations can be raised to tip the equilibrium in favor of product formation. Altering the reaction conditions, such as temperature or pressure, can also encourage the formation of the desired product.
Overall, a number of variables, such as the reaction mechanism, stoichiometry, and reaction conditions, affect the concentrations of reactants and products at equilibrium.
Learn more about equilibrium state
brainly.com/question/12084217
#SPJ4
explain why oxygen forms 2 bonds to hydrogen to make a water molecule, while nitrogen forms 3 bonds to make a molecule of ammonia
Oxygen and nitrogen are both nonmetals, meaning they form covalent bonds when they react.
Oxygen forms two covalent bonds with hydrogen because it has six valence electrons and needs two more electrons to complete its octet. Nitrogen has five valence electrons and needs three more electrons to complete its octet, so it forms three covalent bonds with hydrogen. The chemical formula for a water molecule is H2O, meaning that two hydrogen atoms are bonded to one oxygen atom. The chemical formula for ammonia is NH3, meaning that three hydrogen atoms are bonded to one nitrogen atom. The bond between hydrogen and oxygen is a polar covalent bond, while the bond between hydrogen and nitrogen is a non-polar covalent bond. This is due to the difference in electronegativity between oxygen and nitrogen, which causes oxygen to be more electronegative than nitrogen.
To know more about electronegativity click on below link :
https://brainly.com/question/17762711#
#SPJ11
Mercury concentrations were measured in freshwater shrimp populations in two different ponds, one polluted with mercury and one unpolluted, with a similar food web in each pond. Which of the following best identifies the scientific question that would guide this investigation?
a. How does the food web in a pond affect biomagnification of toxins?
b. How much mercury is found in the tissues of shrimp predators in an unpolluted pond?
c. How do different species of shrimp excrete mercury from their bodies?
d. How much mercury accumulates in the tissues of freshwater shrimp living in a polluted pond?
The scientific question that would guide this investigation is d. how much mercury accumulates in the tissues of freshwater shrimp living in a polluted pond?
This is the best choice among the options because it directly addresses the issue that the investigation aims to address: the levels of mercury concentrations in freshwater shrimp populations in two different ponds, one polluted with mercury and one unpolluted, with a similar food web in each pond.
The question is straightforward and focuses on the main objective of the study, which is to measure the concentration of mercury in the tissues of freshwater shrimp living in the polluted pond.
The other options, while they may be relevant to the study, are not the main focus of the investigation.
Option A, for instance, deals with how the food web in a pond affects biomagnification of toxins.
Option B is concerned with the amount of mercury found in the tissues of shrimp predators in an unpolluted pond, which is not the primary objective of the study.
Option C is focused on the different species of shrimp excreting mercury from their bodies. This may be useful to know, but it is not the main question being investigated.
So, the correct answer will be option d. How much mercury accumulates in the tissues of freshwater shrimp living in a polluted pond?
Learn more about biomagnification on:
https://brainly.com/question/7631542
#SPJ11
what other products are expected to be found in the mother liquor from the recrystallization of the dinitro compound?
The mother liquor from the recrystallization of a dinitro compound is expected to contain other products, such as nitrites, nitrates, and aqueous solutions.
Explanation: In the mother liquor from the recrystallization of the dinitro compound, other products that are expected to be found are generally impurities or by-products that are not soluble in the recrystallization solvent, as well as a small amount of the product that did not crystallize.To remove the impurities that remain in the mother liquor, it is often essential to repeat the recrystallization procedure with a different solvent or a solvent mixture until the desired purity is achieved.In general, recrystallization is a technique that allows for the purification of a chemical substance by dissolving the impure substance in a solvent and then re-crystallizing it from a fresh solvent with appropriate cooling.A dinitro compound, as the name suggests, is a compound that contains two nitro groups. The recrystallization of such compounds often occurs as a result of their insolubility in some solvents at room temperature.
For more such questions on recrystallization
https://brainly.com/question/30023103
#SPJ11
100cm3 of a gas at 27degree Celsius exert a pressure of its volume is increased to 200cm3 at 127 degrees Celsius
Answer: 100cm3 of gas at 27°c exert a pressure of 750mmHg. Calculate its pressure if it's volume is increased to 250cm3 at 127°c? In Chemistry
Explanation:
which of the following properties affects a substance's saturation temperature? multiple choice question. pressure mass volume
The property that affects a substance's saturation temperature is Pressure.
What is saturation temperature?Saturation temperature is the temperature at which a liquid and a gas have the same vapor pressure. The vapor pressure of a liquid is affected by temperature, and at the saturation temperature, the vapor pressure of the liquid equals the pressure of the surrounding atmosphere.
A substance's saturation temperature is influenced by several variables. Pressure is one of the variables that influences the saturation temperature of a substance. When the pressure surrounding a substance rises, its saturation temperature rises.
Read more about mass:
https://brainly.com/question/19385703
#SPJ11
the ph of a liquid is a measure of its acidity or alkalinity. the normal range of ph of blood is:
Answer: The pH of a liquid is a measure of its acidity or alkalinity. The normal range of pH of blood is 7.35-7.45.
What is pH?
A pH of 7 is neutral, a pH of less than 7 is acidic, and a pH of greater than 7 is alkaline. The pH of a solution is calculated as the negative logarithm of the hydrogen ion concentration (pH = -log[H+]), which varies from 0 to 14.The normal range of pH of blood is 7.35-7.45, which is slightly alkaline.
Maintaining the appropriate pH level in the bloodstream is critical for the body to function properly. Blood pH can be affected by a variety of factors, including respiratory and metabolic disorders. When the pH of the blood falls below 7.35, a condition known as acidosis develops. When the pH of the blood rises above 7.45, a condition known as alkalosis develops. Both acidosis and alkalosis can have serious health consequences.
Learn more about pH level here:
https://brainly.com/question/1458045#
#SPJ11
a polar covalent bond is associated with which of the following? group of answer choices interactions between nuclei unequal sharing of electrons equal sharing of electrons the transfer of electrons
A polar covalent bond is associated with unequal sharing of electrons.
A polar covalent bond is a covalent bond in which electrons are not equally shared between the bonded atoms. It is formed when two or more atoms share electrons in such a manner that the nucleus of one atom exerts a greater attraction on the electrons than the other atom.
As a result of the unequal sharing of electrons, the atoms have partial charges. In polar covalent bonds, the electrons spend more time near the atom with a stronger nucleus. As a result, one atom in a polar covalent bond becomes partially negative, and the other becomes partially positive. Polar covalent bonds can be found in a variety of compounds, including water, ammonia, and hydrogen chloride, among others.
Learn more about polar covalent bond at:
https://brainly.com/question/10166021
#SPJ11
Given that the partial charges on C and O in carbon monoxide are 0.020 and 0.020, respectively, calculate the dipole moment of CO. (The distance between the partial charges, r, is 113 pm.)
Answer:
2020 from da 230 get it right fam
Explanation:
A hand of bananas is a small bunch made up of 5 bananas ( each banana is called a finger). If a large bunch of bananas is made up of 10 hands, how many bananas does it contain?
There are 50 bananas total in the enormous bunch of bananas.
How many bananas are there in a bunch?There are 10 bunches of bananas, and each bunch has 5 bananas; therefore, there are 50 bananas in all.The difference between a hand and a bunch of bananas. A finger is a single banana. A hand is made up of five to six fingers.A group of hands are all on one stem.Each bunch of bananas that a banana tree produces will eventually perish and need to be removed. Within a year, a fresh shoot will emerge from the rhizome to create a fresh bunch.Visit for more information on a bunch of bananas.
https://brainly.com/question/28015501
#SPJ1
What product is formed when the compound is treated with Tollens reagent (Ag2O,NH4OH) ? With some compounds, no reaction occurs. If no reaction occurs, draw the reactant.
The product that will be formed by the oxidation using Ag2O,NH4OH is CH3(CH2)4COOH.
How are primary alcohols oxidized using Ag2O?Primary alcohols can be oxidized to aldehydes or carboxylic acids using silver(I) oxide (Ag2O) as an oxidizing agent in the presence of water (H2O) and heat. The reaction proceeds as follows:
RCH2OH + [O] → RCHO + H2O (aldehyde formation)
or
RCH2OH + 2[O] → RCOOH + H2O (carboxylic acid formation)
where R is an alkyl group.
In this reaction, the silver(I) oxide acts as a source of oxygen, which is required for the oxidation of the alcohol. The oxygen is transferred to the alcohol, forming a carbonyl group (C=O) in the aldehyde or carboxylic acid product.
Learn more about alcohols:https://brainly.com/question/30829120
#SPJ1
a scientist conducts an experiment to determine the rate of the following reaction: if the initial concentration of n2 was 0.400 m and the concentration of n2 was 0.350 m after 0.100 s, what is the average rate of reaction over the first 100 milliseconds?
After 0.100 s, the average rate of reaction over the first 100 milliseconds is 0.25 mol s^-1. if the initial concentration of n2 was 0.400 m and the concentration of n2 was 0.350 m.
The average rate of reaction over the first 100 milliseconds when the initial concentration of N2 was 0.400 M and the concentration of N2 was 0.350 M after 0.100 s can be calculated as follows:
Average rate of reaction = {N2 consumed or produced in mol} / {time in seconds}
The balanced chemical equation for the reaction is:
N2(g) + 3H2(g) → 2NH3(g)
As per the given equation, one mole of N2 reacts to produce two moles of NH3. So, the mole of N2 consumed in the reaction would be equal to half the mole of NH3 produced.
Therefore, mole of N2 consumed = (1/2) × (0.050 M) = 0.025 M
Now, the average rate of reaction can be calculated as follows:
Average rate of reaction = {N2 consumed or produced in mol} / {time in seconds}
= 0.025 mol / 0.100 s
= 0.25 mol s^-1
Therefore, the average rate of reaction over the first 100 milliseconds is 0.25 mol s^-1.
For more such questions on rate of reaction , Visit:
https://brainly.com/question/24795637
#SPJ11
what does the retention factor mean in terms of solubility of the pigments in the mobile phase and their interactions with the stationary phase
In terms of the solubility of the pigments in the mobile phase and their interactions with the stationary phase, the retention factor is an indicator. It is a measure of how well the pigments bind to the stationary phase relative to the mobile phase.
The retention factor in chromatography refers to the distance traveled by the compound from the starting line to the solvent front divided by the distance traveled by the solvent front.
It is the ratio of the distance that the compound traveled (in a particular solvent system) to the distance traveled by the solvent. The stationary phase can either be polar or non-polar.
The higher the retention factor, the better the pigments bind to the stationary phase and the less soluble they are in the mobile phase.
To learn more about retention factors refer: https://brainly.com/question/24731831
#SPJ11
Answer with the Matching-match the letter with the correct item
Synthesis and decomposition reactions are two types of chemical reactions that involve the formation and breaking of chemical bonds between atoms and molecules.
A synthesis reaction, also known as a combination reaction, occurs when two or more reactants combine to form a single, more complex product. The general equation for a synthesis reaction is A + B → AB.
A decomposition reaction, on the other hand, is the opposite of a synthesis reaction. It occurs when a single reactant breaks down into two or more simpler products. The general equation for a decomposition reaction is AB → A + B.
Learn about decomposition reaction here https://brainly.com/question/14608831
#SPJ1
what is it called when the partial positive and negative charges of water molecules are attracted to the negative and positive charges
The phenomenon when the partial positive and negative charges of water molecules are attracted to the negative and positive charges is called hydrogen bonding.
Hydrogen bonding occurs when the partially positive hydrogen atom of one water molecule is attracted to the partially negative oxygen atom of another. This creates an electrostatic bond between the molecules and results in a stronger intermolecular force than other dipole-dipole attractions.
As a result, hydrogen bonding is the strongest intermolecular force and is responsible for many of the physical and chemical properties of water, such as its high boiling point and surface tension.
To know more about hydrogen bonding click on below link :
https://brainly.com/question/30885458#
#SPJ11
quartz is a solid in which atoms are not arranged in an orderly pattern. group of answer choices true false
Quartz is a solid in which atoms are not arranged in an orderly pattern.
The given statement is false.
Quartz is a type of mineral that is naturally occurring. It has a chemical formula of SiO2 or silicon dioxide, and its crystal structure is hexagonal or trigonal in shape. Quartz is one of the most abundant minerals on the earth's surface. It is composed of tiny particles of silicon dioxide, which have a distinctive tetrahedral arrangement.
The atoms in quartz are arranged in an orderly pattern, which makes it a crystalline solid. These orderly arrangements of atoms are what give quartz its unique physical and chemical properties.Quartz is a hard, durable mineral that is used in many different industries. It is used to make glass, ceramics, electronics, and semiconductors, among other things.
For more such questions on quartz, click on:
https://brainly.com/question/30621853
#SPJ11
specifically, what should you look at in the infrared spectrum of the ester you synthesized that will show the absence of the reactants?
In the infrared spectrum of the ester you synthesized, specifically, you should look for the presence of ester functional group peaks and the absence of reactants' peaks
When looking at the infrared spectrum of the ester that you synthesized, you should specifically look for the absence of the reactants. This can be seen in the form of absorption peaks in the infrared spectrum. Any absorption peaks that are present in the spectrum indicate that the reactants are still present in the ester, while a lack of absorption peaks suggests that the reactants have been fully converted into the ester. Therefore, the absence of peaks in the infrared spectrum is a good indication that the reactants have been consumed in the reaction and the synthesis was successful.
Know more about ester here:
https://brainly.com/question/28118164
#SPJ11
what is the ph of a solution if 10 ml of a 1 m hcl solution is added to 10 ml of a 1 m naoh solution?
The pH of a solution if 10 ml of a 1 M HCl solution is added to 10 ml of a 1 M NaOH solution can be calculated as follows:
First, let's find the number of moles of HCl and NaOH in the solution. Number of moles of HCl = Concentration of HCl x Volume of HClNumber of moles of HCl = 1 M x (10 ml/1000 ml)Number of moles of HCl = 0.01 molesNumber of moles of NaOH = Concentration of NaOH x Volume of NaOHNumber of moles of NaOH = 1 M x (10 ml/1000 ml)Number of moles of NaOH = 0.01 molesNext, let's find the net number of moles of H+ and OH- ions.Number of moles of H+ ions = Number of moles of NaOH - Number of moles of HCl.Number of moles of H+ ions = 0.01 - 0.01Number of moles of H+ ions = 0 molesNumber of moles of OH- ions = Number of moles of HCl - Number of moles of NaOHNumber of moles of OH- ions = 0.01 - 0.01Number of moles of OH- ions = 0 molesSince the net number of moles of H+ ions and OH- ions is zero, the solution is neutral. The pH of a neutral solution is 7. Therefore, the pH of the solution is 7.
To know more about pH click on below link :
https://brainly.com/question/491373#
#SPJ11
which answer best describes the transfer of heat that occurs when 1.31 mol h2 reacts with 0.624 mol o2?
The transfer of heat that occurs when 1.31 mol H2 reacts with 0.624 mol O2 is an exothermic reaction, where the reactants release energy as heat. This heat is absorbed by the product and can be used to do work.
When 1.31 mol of H2 reacts with 0.624 mol of O2, heat transfer occurs through an exothermic reaction. Heat is released by the reactants as they react and form a new product.
This release of heat is called the enthalpy of reaction (ΔH).
When the reactants form a product, energy is released from the reactants as heat. This heat is absorbed by the product. This heat transfer can be seen in an energy diagram for the reaction.
The energy released in the reaction can be used to do work. Heat transfer occurs in the form of kinetic energy, which is the energy of motion. This kinetic energy can be used to do work, such as powering machinery.
Heat transfer is important in many chemical and physical processes, such as cooking and cooling.
to know more about exothermic reaction refer here:
https://brainly.com/question/10373907?referrer=searchResultshttps://brainly.com/question/10373907#
#SPJ11
acetic acid has a ka of 1.80x10-5. what is the ph of a buffer solution made from 0.150 m hc2h3o2 and 0.530 m c2h3o2 -?
Acetic acid has a ka of 1.80x10-5. The pH of a buffer solution made from 0.150 m hc2h3o2 and 0.530 m c2h3o2 is 4.76.
The pH of a buffer solution produced from 0.150 M HC2H3O2 and 0.530 M C2H3O2 is 4.76.
The following are the steps to solve the problem:
Acetic acid is a weak acid with the formula CH3COOH, which is also known as ethanoic acid.
HC2H3O2 is the molecular formula for this substance.
Acetic acid has a Ka of 1.8 x 10-5.
The ionization of acetic acid can be expressed as follows: CH3COOH + H2O ↔ H3O+ + CH3COO-
The ionization constant, Ka, is equal to the product of the concentration of H3O+ and CH3COO- ions divided by the concentration of CH3COOH.
Hence, Ka = ([H3O+] [CH3COO-])/[CH3COOH]
The Henderson-Hasselbalch equation is used to compute the pH of a buffer solution.
pH = pKa + log (base/acid), where pKa = -logKa.
In the equation, the base is C2H3O2-, and the acid is HC2H3O2.
Substituting the values in the equation, pH = -log1.8 x 10-5 + log(0.530/0.150) = 4.76.
Therefore, the pH of a buffer solution produced from 0.150 M HC2H3O2 and 0.530 M C2H3O2 is 4.76.
To know more about pH calculation, refer here:
https://brainly.com/question/1195974#
#SPJ11
the naturally occurring form of a metal that is concentrated enough to allow economical recovery of the metal is known as
The economically recoverable form of a metal is known as ore.
Ores are generally composed of economically valuable minerals or metals that can be extracted from the surrounding rock. These minerals and metals are often referred to as "commodities" and their prices can fluctuate depending on market conditions.
In order for ore to be economically viable, it must contain a sufficient concentration of the desired metal or mineral, which makes it profitable to extract. In addition, it must also be accessible and extractable with existing technology. Some ores are more difficult to extract than others due to their physical characteristics, which can make them more costly to process.
For instance, ores that are particularly hard or dense may require additional energy to break down and process, thus driving up costs. Similarly, some metals and minerals may require more complicated extraction techniques and more resources than others.
Ore bodies can be found on the surface or beneath the earth's surface and can be mined through open-pit or underground mining.
In conclusion, the ore is the naturally occurring form of a metal that is concentrated enough to allow economical recovery of the metal. Ores vary in their concentration of minerals and metals and their extraction processes require different levels of energy, resources, and technology.
Therefore, the naturally occurring form of a metal that is concentrated enough to allow economical recovery of the metal is known as ore.
To know more about ore, refer here:
https://brainly.com/question/89259#
#SPJ11
consider the multistep reaction below. what is the balanced chemical equation of the overall reaction?
The overall reaction of the multistep reaction is: 2A + B → C + D
This reaction can be broken down into two individual steps. In the first step, A and B react to form an intermediate product, X. The balanced chemical equation for this step is: A + B → X. In the second step, the intermediate product X is reacted with A to form C and D. The balanced chemical equation for this step is:X + A → C + D
Combining these two equations yields the overall balanced chemical equation:
2A + B → C + D
In summary, the overall balanced chemical equation for the multistep reaction is 2A + B → C + D. This equation shows that two molecules of A and one molecule of B will combine to form one molecule of C and one molecule of D.
To know more about chemical equation click on below link :
https://brainly.com/question/19626681#
#SPJ11
palladium crystallizes in a face-centered cubic unit cell. its density is 12.0 g / cm3 at 27oc. calculate the atomic radius of pd.
Palladium crystallizes in a face-centered cubic unit cell. Its density is 12.0 g/cm3 at 27°C. Calculate the atomic radius of Pd.
A face-centered cubic (FCC) lattice is used by Palladium. As a result, the lattice parameter of palladium is a
=(4V/√3)^(1/3) ,
where V is the atomic volume of palladium. The formula for the density of a substance is d=m/V, where d is the density, m is the mass, and V is the volume of the substance. In this situation, m = M (mass of 1 mole of palladium), which can be expressed as M= n × m, where n is the number of moles of palladium and m is the mass of one palladium atom. Therefore, the density formula becomes
d=M/V.
Palladium's atomic volume is V=(4πr^3/3) /N_a,
where Na is Avogadro's constant (6.022 × 10^23 mol^-1). The atomic radius of Pd is given by the following formula:r=(a/2) × √2The density of Pd is given by the following formula
d=M/V
The molar mass of Pd can be calculated from its atomic weight (106.42 g/mol), M=106.42 g/mol The atomic volume of Pd is given by the following formula:
V= 4r^3/3Na
Use this value of V to determine the lattice parameter a = (4V/√3)^(1/3).r = (a/2) × √2
Calculations:d = 12.0 g/cm3M = 106.42 g/mol
V = (4πr^3/3) /N_a
Let's solve for V:
V = (4πr^3/3) /N_a = (4π (162.5 × 10^-30 m)^3/3) / (6.022 × 10^23 mol^-1) = 8.927 × 10^-6 cm^3/mol
The lattice parameter can be determined now
:a = (4V/√3)^(1/3) = (4 (8.927 × 10^-6 cm^3/mol) / √3)^(1/3) = 3.891 × 10^-8 cmThe atomic radius can be determined:r = (a/2) × √2 = (3.891 × 10^-8 cm/2) × √2 = 1.096 × 10^-8 cm
The atomic radius of Pd is 1.096 × 10^-8 cm.
Learn more about face-centered cubic (FCC) lattice at brainly.com/question/14885097
#SPJ11
What is the binding energy b of the last neutron of silicon‑30? the atomic mass of silicon‑30 is 29. 973770 u, whereas the atomic mass of silicon‑29 is 28. 976495 u
The binding energy of the last neutron in silicon-30 is 2.346 × 10^-12 J.
The binding energy of a nucleus is the energy required to separate all of its constituent nucleons (protons and neutrons) from each other to an infinite distance. The binding energy per nucleon is a measure of the stability of a nucleus, with higher values indicating greater stability.
To calculate the binding energy of the last neutron in silicon-30, we need to use the atomic masses of silicon-30 and silicon-29 to determine the mass defect of silicon-30:
mass defect = (atomic mass of protons and neutrons) - (atomic mass of nucleus)
The atomic mass of silicon-30 is 29.973770 u, and the atomic mass of silicon-29 is 28.976495 u. Therefore, the mass defect of silicon-30 is:
mass defect = (30 protons + 30 neutrons) × 1.008665 u - 29.973770 u
mass defect = 0.259625 u
This means that the total binding energy of the silicon-30 nucleus is:
binding energy = mass defect × c^2
where c is the speed of light in a vacuum, which is approximately 2.998 × 10^8 m/s.
binding energy = 0.259625 u × (1.66054 × 10^-27 kg/u) × (2.998 × 10^8 m/s)^2
binding energy = 2.335 × 10^-11 J
Since we are interested in the binding energy of the last neutron in silicon-30, we need to subtract the binding energy of the silicon-29 nucleus (which has 29 neutrons) from the binding energy of the silicon-30 nucleus:
binding energy of last neutron = binding energy of silicon-30 nucleus - binding energy of silicon-29 nucleus
binding energy of last neutron = (30 nucleons × 2.335 × 10^-11 J) - (29 nucleons × 2.308 × 10^-11 J)
binding energy of last neutron = 2.346 × 10^-12 J.
Learn more about binding energy
https://brainly.com/question/30073915
#SPJ4
1.000 g of a weak base was titrated with hcl and gave the above curve. what is the most likely base?
Answer: The most likely base is an amine or an organic base with a pKa value of approximately 6.4.
To determine the most likely base, one must examine the shape of the titration curve obtained from the titration of 1.000 g of a weak base with HCl. The shape of the curve would give an insight into the identity of the weak base.
The following information can be deduced from the given titration curve: The equivalence point (stoichiometric point) is located at approximately pH 6.4. This corresponds to the neutralization of the weak base with HCl to form the salt of the weak base.
At pH <6.4, the weak base is partially protonated (acidic) and exists in a conjugate acid form. When the pH is greater than 6.4, the weak base is partially deprotonated (basic) and exists in the conjugate base form.
In conclusion, the most likely base is an amine or an organic base with a pKa value of approximately 6.4.
Learn more about titrate here:
https://brainly.com/question/2728613#
#SPJ11
oxygen gas is collected over water. the total pressure (the o2 pressure the water vapor pressure) is 748 torr. the temperature of the water is such that the water vapor pressure is 23 torr. what is the partial pressure of the oxygen gas in torr? answer:
The partial pressure of oxygen gas in torr is 725 torr. when oxygen gas is collected over water.
oxygen gas is collected over water. the total pressure (the o2 pressure the water vapor pressure) is 748 torr. the temperature of the water is such that the water vapour pressure is 23 torr. the partial pressure of the oxygen gas in torr.
The total pressure of the mixture
(the oxygen pressure + the water vapour pressure) is 748 torr.
At a temperature at which the water vapour pressure is 23 torr.
The partial pressure of the oxygen gas in torr can be calculated as follows;
partial pressure of O2 = total pressure - vapour pressure of water
= 748 torr - 23 torr= 725 torr
Therefore, the partial pressure of the oxygen gas in torr is 725 torr.
For more such questions on partial pressure , Visit:
https://brainly.com/question/19813237
#SPJ11
in a first order decomposition, the constant is 0.00729 sec-1. what percentage of the compound is left after 2.96 minutes
27.7% of the compound remains after 2.96 minutes.
Decomposition is the breakdown of a molecule into smaller molecules or elements. It is the reverse of a chemical reaction. The rate of decomposition of a compound can be determined by a first-order reaction.
The first-order rate constant is a measure of how quickly a compound decomposes over time. It is represented by the letter k.
In a first-order reaction, the rate of decomposition is proportional to the concentration of the compound.
The equation is given as follows:Rate = -k[A]Where k is the rate constant, and [A] is the concentration of the compound. The negative sign represents the decrease in concentration of the compound over time.
Equation gives the following:ln[A]t = -kt + ln[A]0Where ln is the natural logarithm, [A]t is the concentration of the compound at time t, and [A]0 is the initial concentration of the compound.
Rearranging this equation gives the following:A = A0e-kttWhere A is the concentration of the compound at time t, and A0 is the initial concentration of the compound.
The percentage of the compound that remains after a given amount of time can be determined by dividing the concentration of the compound at that time by the initial concentration and multiplying by 100.
The equation is given as follows:% remaining = (A/A0) x 100
Where % remaining is the percentage of the compound that remains, A is the concentration of the compound at time t, and A0 is the initial concentration of the compound.
We can use the given data to determine the percentage of the compound that remains after 2.96 minutes. The rate constant is given as k = 0.00729 sec-1.
Therefore, the equation for the concentration of the compound at time t is:A = A0e-ktt, we get:A = A0e-0.00729(2.96 x 60)A = A0e-1.303
Therefore, the percentage of the compound that remains is:% remaining = (A/A0) x 100% remaining = (e-1.303) x 100% remaining = 27.7%Therefore, 27.7% of the compound remains after 2.96 minutes.
to know more about compound refer here:
https://brainly.com/question/13516179#
#SPJ11
a sample is sent to the laboratory for an anti-xa assay. the result of the ptt is 65.7 seconds. the result of the anti-xa assay is 0.9 u/ml of heparin. the patient is on lovenox. their anti-xa level is:
b. Therapeutic. For treatment dosage therapy, the therapeutic anti-Xa level is between 0.5 and 1 units/mL. For prophylactic dosage treatment, the ideal anti-Xa level is between 0.2 and 0.4 units/ml.
The activity of heparin, including low molecular weight heparin, is measured using the anti-Xa assay. Anti Xa is an ambiguous name. Heparin activity is what the lab truly reports when it says "against Xa." Therefore, low anti-Xa correlates with lower heparin activity, whereas high Xa correlates with higher heparin activity. The medicine and the indication both affect the therapeutic anti-Xa activity. Unfractionated heparin has a different range than low molecular weight heparin. For the treatment of venous thromboembolism, a therapeutic range for unfractionated heparin is 0.35–0.7 and for low molecular weight heparin, it is 0.5–1. 10% less is the suggested goal for acute coronary syndrome.
Learn more about Therapeutic here:
https://brainly.com/question/23798561
#SPJ4
Complete Question:
A sample is sent to the laboratory for an anti-Xa assay. The result of the PTT is 65.7 seconds. The result of the anti-Xa assay is 0.9 U/mL of heparin. The patient is on Lovebox. Their anti-Xa level is:
a. subtherapeutic
b. therapeutic
c. supratherapeutic
d. prophylactic
metallic bonds... metallic bonds... a. ...allow for high electrical conductivity in a material. b. ...are non-directional. c. ...allow a material to plastically deform.
Metallic bonds a. allow for high electrical conductivity in a material. Metallic bonds are non-directional. They also allow a material to plastically deform.
Metallic bonding is the bonding between the positively charged nuclei of metal atoms and the electrons in the metal's outermost electron shell. Metallic bonding in metals is believed to be like a sea of electrons that are free to move throughout the entire metallic crystal. This is why metals conduct heat and electricity so effectively, making them excellent conductors.
The atoms in a metal are not held together by covalent bonds, but rather by metallic bonds. They are typically held together in a crystal lattice. The electrons in metals are not held to any specific atom or molecule, but rather they move around freely among the metal atoms' positively charged ion cores. The metallic bond is a non-directional bond. The electrons in the metal are delocalized, which means they are free to move around the metal lattice.
As a result, metals are malleable and ductile, meaning they can be formed into sheets or drawn into wires. Metals can also be deformed without being broken or shattered because the metallic bond is non-directional. In general, metals are good conductors of electricity and heat because their free electrons can easily move in response to an electric or thermal current. So, the correct option are: metallic bonds allow for high electrical conductivity in a material, metallic bonds are non-directional, and metallic bonds allow a material to plastically deform.
Learn more about covalent bonds at:
https://brainly.com/question/11674395
#SPJ11
how could you perform an experiment by adjusting the ionic concentrations to determine the cause of the resting potential?
To perform an experiment to determine the cause of the resting potential by adjusting the ionic concentrations, you will need to complete the following steps.
First, you should set up the appropriate apparatus for the experiment. This will include a solution chamber, an electrode, a reference electrode, and a recording device.
Second, you should prepare the solutions in the chamber, adjusting the concentrations of the various ions. You may want to begin with a balanced solution, then adjust one of the ions while keeping the others constant.
Third, you should measure the resting potential of the cell. Record the values of the resting potential as you adjust the ion concentrations.
Fourth, you should analyze the data. You can look for correlations between the resting potential and the concentration of the ions.
Finally, you should form a conclusion. From your data, you should be able to determine which ion(s) are responsible for the resting potential.
By following these steps, you can conduct an experiment to determine the cause of the resting potential by adjusting the ionic concentrations.
To know more about resting potential click on below link :
https://brainly.com/question/20277449#
#SPJ11
The equilibrium constant, Kc, for the following reaction is 11.8 at 752 K. 2NH3(g) N2(g) + 3H2(g) Calculate Kc at this temperature for the following reaction: 1/2N2(g) + 3/2H2(g) NH3(g) The equilibrium constant, Kc, for the following reaction is 5.70 at 719 K. 2NH3(g) N2(g) + 3H2(g) Calculate Kc at this temperature for the following reaction: NH3(g) 1/2N2(g) + 3/2H2(g)
The equilibrium constant for the new reaction at 752 K is approximately 0.29 and at 719 K is approximately 0.42.
Step wise explanation:
1) For the first reaction, the equilibrium constant (Kc) is given as 11.8 at 752 K for the reaction:
[tex]2NH_{3}[/tex](g) ⇌ [tex]N_{2}[/tex](g) + [tex]3H_{2}[/tex](g)
You are asked to calculate Kc for the following reaction:
[tex]1/2N_{2} + 3/2H_{2}[/tex] ⇌ [tex]NH_{3}[/tex](g)
To find Kc for the new reaction, note that it is the reverse of the original reaction with all coefficients divided by 2. To calculate the equilibrium constant for the reverse reaction, take the reciprocal of the original Kc, and then raise it to the power of the coefficients ratio (1/2):
Kc (new) =[tex]\sqrt{ (1 / Kc (original))}[/tex] = [tex]\sqrt{(1 / 11.8)}[/tex] ≈ 0.29
So, the equilibrium constant for the new reaction at 752 K is approximately 0.29.
2) For the second reaction, the equilibrium constant (Kc) is given as 5.70 at 719 K for the reaction:
[tex]2NH_{3}[/tex](g) ⇌ [tex]N_{2}[/tex](g) + [tex]3H_{2}[/tex](g)
You are asked to calculate Kc for the following reaction:
[tex]NH_{3}[/tex](g) ⇌ [tex]1/2N_{2}[/tex](g) + [tex]3/2H_{2}[/tex](g)
This new reaction is the reverse of the original reaction with all coefficients divided by 2. Similar to the first case, take the reciprocal of the original Kc and then raise it to the power of the coefficients ratio (1/2):
Kc (new) = [tex]\sqrt{(1 / Kc (original))}[/tex] = [tex]\sqrt{(1 / 5.70)}[/tex] ≈ 0.42
So, the equilibrium constant for the new reaction at 719 K is approximately 0.42.
To learn more about equilibrium constant; https://brainly.com/question/19340344
#SPJ11