The magnitude of the magnetic flux through each turn of the coil at the instant when the current is 3.60 A is 3.72×10⁻⁶ Wb.
The quantity of magnetic field traveling through a specific region or surface is measured by magnetic flux. It is described as the result of the area that the magnetic field travels through and its magnitude, where the area is perpendicular to the field's direction. The Weber is the magnetic flux SI unit (Wb)
Given that,
EMF = 18.0 mV = 0.018 V
N = 484 turns
(dΦ/dt) = 10.0 A/s
I = 3.60 A
The equation that relates the electromotive force (EMF) induced in a coil to the rate of change of magnetic flux is:
EMF = -N(dΦ/dt)
Rearranging the equation to solve for Φ:
Φ = -EMF/(N(d/dt))
= -(0.018 V)/(484(10.0 ))
= -3.72×10⁻⁶ Wb
The magnitude of the magnetic flux through each turn of the coil at the instant when the current is 3.60 A is 3.72×10⁻⁶ Wb.
To learn more about Magnetic flux, refer to:
https://brainly.com/question/29221352
#SPJ4
select each of the true statements below think about initial/final states! what's a conservative force? a. the kinetic energy can never be negative. b. spring a is stiffer than b ( ). a person must do less work on the block connected to spring a if both springs are ideal and the blocks are pulled by the same amount. c. the work a person must do to raise a box onto a platform does not depend on how fast it is raised. d. the kinetic energy of an object depends on the reference frame of the observer. e. if the moon revolves around earth in a perfectly circular orbit, then earth does do work on the moon. f. the friction force is a non-conservative force. g. work can be done in the absence of motion. h. the kinetic energy of an object does not depend on the direction of the motion involved. i. none of the above.
The true statements according to initial/final states are : the kinetic energy can never be negative, the work a person must do to raise a box onto a platform does not depend on how fast it is raised. the kinetic energy of an object depends on the reference frame of the observer. the kinetic energy of an object does not depend on the direction of the motion involved. The correct options are a,c, d, h
The kinetic energy can never be negative: The kinetic energy of an object is defined as the energy it possesses due to its motion. The kinetic energy is always positive or zero because it is proportional to the square of the speed, and the speed cannot be negative.
The work a person must do to raise a box onto a platform does not depend on how fast it is raised: When a person raises a box onto a platform, the work done depends only on the initial and final states of the box-platform system, which are determined by the gravitational potential energy difference. The speed at which the box is raised does not affect the work done.
The kinetic energy of an object depends on the reference frame of the observer: The kinetic energy of an object is defined as the energy it possesses due to its motion. The kinetic energy depends on the speed of the object, which is relative to the observer's reference frame.
The kinetic energy of an object does not depend on the direction of the motion involved: The kinetic energy of an object is defined as the energy it possesses due to its motion. The kinetic energy depends only on the speed of the object and not on the direction of motion.
Therefore, options a,c,d and h are true.
For more such questions on kinetic energy, click on:
https://brainly.com/question/8101588
#SPJ11
in a systems current configuration, a rotating rod is subjected to a steady bending moment. in redesigning the system, the rod is made stationary and and alternating bending moment of the same magnitude is applied, what is the impact on the endurance limit
When the rod is made stationary and subjected to an alternating bending moment of the same magnitude, the endurance limit is lower compared to the rotating rod with a steady bending moment. This is because the alternating stress cycles make the material more susceptible to fatigue failure.
In the student's question, there is a rotating rod in a system subjected to a steady bending moment. In the redesigned system, the rod is made stationary and an alternating bending moment of the same magnitude is applied. To determine the impact on the endurance limit, let's analyze both configurations step-by-step.
1. In the current configuration, the rotating rod is subjected to a steady bending moment. This means that the rod is experiencing constant stress over time. In this case, the endurance limit is defined as the maximum stress the rod can withstand for an infinite number of cycles without failure.
2. In the redesigned system, the rod is made stationary, and an alternating bending moment of the same magnitude is applied. This means that the rod experiences cyclic stress, where the stress varies from a maximum positive value to a maximum negative value. In this case, the endurance limit is lower compared to the constant stress situation, as the material is more prone to fatigue failure due to repeated stress cycles.
For more such questions on stress cycles
brainly.com/question/29735193
#SPJ11
What is the heat required to decrease the temperature of a 40 keg object by 30 K if the specific heat of the object is 950J/kg*K?
Therefore, the heat required to decrease the temperature of a 40 kg object by 30 K is 1,140,000 J.
What distinguishes latent heat from specific heat?The energy absorbed or released as a substance changes phases is known as latent heat. The amount of heat needed to raise a substance's temperature by one degree Celsius (or one Kelvin) in one gramme while maintaining a constant pressure is known as its specific heat.
The heat required to decrease the temperature of an object can be calculated using the formula:
Q = m * c * ΔT
where Q is the heat required, m is the mass of the object, c is the specific heat of the object, and ΔT is the change in temperature.
Given that the object has a mass of 40 kg and a specific heat of 950 J/kg*K, and the temperature needs to be decreased by 30 K, we can substitute these values in the formula to find the heat required:
Q = 40 kg * 950 J/kg*K * 30 K
Q = 1,140,000 J
To know more about temperature visit:-
brainly.com/question/4160783
#SPJ9
If the wavelength of a water wave decreases, then what happens to its velocity?
Answer:
The velocity of a water wave depends on the properties of the medium through which it is propagating, such as the density and elasticity of the medium. It does not depend on the wavelength of the wave.
Therefore, if the wavelength of a water wave decreases, its velocity does not change. However, the frequency of the wave will increase, as frequency and wavelength are inversely proportional to each other for a wave with a constant velocity. This means that more waves will pass through a given point in a unit of time, which can affect other properties of the wave, such as its intensity and energy.
g during a circus act, an elderly performer thrills the crowd by catching a cannon ball shot at him. the cannon ball has a mass of 78.0 kg and its horizontal component of velocity is 8.50 m/s when the 65.0 kg performer catches it. if the performer is on nearly frictionless roller skates, what is his recoil velocity in meters per second?
The recoil velocity of the performer in meters per second is approximately 3.06 m/s. Since the performer is on nearly frictionless roller skates, he will move backward with this velocity after catching the cannonball.
In this scenario, we can apply the principle of conservation of momentum. The total momentum of the system (cannonball and performer) before the catch is equal to the total momentum after the catch. Since the performer is initially at rest, the momentum of the cannonball before the catch is equal to its mass times its velocity.
The momentum of the system after the catch is the sum of the momenta of the cannonball and the performer. Let's assume that the recoil velocity of the performer is v. Then, according to the conservation of momentum principle:
(mass of cannonball) x (velocity of cannonball) = (mass of cannonball + mass of performer) x (final velocity of the system)
Plugging in the given values, we get:
(78.0 kg) x (8.50 m/s) = (78.0 kg + 65.0 kg) x (v)
Solving for v, we get:
v = [(78.0 kg) x (8.50 m/s)] / (78.0 kg + 65.0 kg)
v ≈ 3.06 m/s
To learn more about recoil velocity
https://brainly.com/question/14232084
#SPJ4
I have a room that is sealed air tight that is sitting at 90 degrees and another room, also sealed air tight, that is sitting at 40 degrees. What happens when I open the door between the rooms? How does the air flow? What does the temperature become when the rooms reach equilibrium?
Answer: When you open the door between the two rooms, the air will flow from the warmer room to the cooler room until the temperatures in both rooms reach equilibrium. This process is called heat transfer. The final temperature will depend on the size and insulation of the rooms, as well as other factors such as humidity and air pressure.
does the friction force on the book point into the wall, out of the wall, up, down, or is there no friction force? explain
when a book slides down a slanted wall, the friction force on the book points out of the wall.
When a book slides down a slanted wall, the direction of the friction force is the friction force on the book points out of the wall, according to the answer.The direction of the frictional force acting on the book is the force acting on an object in motion to oppose its motion, which points in the opposite direction of the movement.
If the book slides down a slanted wall, the frictional force must be directed out of the wall because it opposes the movement of the book, which is directed towards the wall.
Learn more about friction force here:
https://brainly.com/question/30280752
#SPJ11
an 1,810 w toaster, a 1,440 w electric frying pan, and a 60 w lamp are plugged into the same outlet in a 15 a, 120 v circuit. (the three devices are in parallel when plugged into the same socket.) (a) what current (in a) is drawn by each device?
Explanation:
Watts = amp * volts
watts/ volts = amps
1810 w / 120 v = 15.5 A
1440 w / 120 v = 12 A
60 w/ 120 v = .5 A
In reality, they are probably drawing ZERO amps as the circuit breaker (15 Amps as given) will likely trip or the wires will burn !
The current drawn by each device in a parallel circuit is determined by the resistance of each device.
Since the toaster has the highest resistance, it will draw the least amount of current, while the electric frying pan with the lowest resistance will draw the highest current. The lamp, being a light bulb, will draw a medium amount of current.
Using Ohm's law, the current drawn by each device can be calculated as follows:
Toaster: 1,810 W ÷ 120 V = 15.08 A
Electric Frying Pan: 1,440 W ÷ 120 V = 12 A
Lamp: 60 W ÷ 120 V = 0.5 A
Since all three devices are connected in parallel, the total current drawn from the outlet will be the sum of the individual currents drawn by each device, which is 15.58 A. This is below the maximum current rating of the circuit (15 A), so the circuit is safe.
Know more about Ohm's law here
https://brainly.com/question/1247379#
#SPJ11
pls help
Problem 1:
The 2022 Tesla Model S Plaid can accelerate from 0-60 mph in 2.28 seconds. How many g’s does the
driver experience during this acceleration? How far does the car travel to hit 60 mph?
The driver experiences about 0.835 g, g-force during the acceleration. and the car travels about 49.8 meters (163 feet) to hit 60 mph.
What is g-force?
To calculate the g-force experienced by the driver during the acceleration, we need to use the formula:
g-force = acceleration due to gravity / acceleration of the car
The acceleration due to gravity is approximately 9.81 m/s², or 32.2 ft/s².
The acceleration of the car can be calculated by converting the acceleration from 0-60 mph to meters per second squared (m/s²). We can use the following formula to convert:
a = (v_f - v_i) / t
where:
a = acceleration
v_f = final velocity (60 mph in this case, which is 26.8 m/s)
v_i = initial velocity (0 mph in this case, which is 0 m/s)
t = time taken to reach final velocity (2.28 seconds in this case)
Plugging in the values, we get:
a = (26.8 m/s - 0 m/s) / 2.28 s
a ≈ 11.75 m/s²
Now we can calculate the g-force experienced by the driver:
g-force = 9.81 m/s² / 11.75 m/s²
g-force ≈ 0.835 g
Therefore, the driver experiences about 0.835 g during the acceleration.
To calculate the distance traveled by the car to hit 60 mph, we can use the following formula:
d = v_i * t + 0.5 * a * t²
where:
d = distance traveled
v_i = initial velocity (0 mph in this case, which is 0 m/s)
t = time taken to reach final velocity (2.28 seconds in this case)
a = acceleration (11.75 m/s²)
Plugging in the values, we get:
d = 0 m/s * 2.28 s + 0.5 * 11.75 m/s² * (2.28 s)²
d ≈ 49.8 m
Therefore, the car travels about 49.8 meters (163 feet) to hit 60 mph.
To know more about gravity, visit:
https://brainly.com/question/14874038
#SPJ1
Complete question is: The 2022 Tesla Model S Plaid can accelerate from 0-60 mph in 2.28 seconds. The driver experiences about 0.835 g, g-force during the acceleration. and the car travels about 49.8 meters (163 feet) to hit 60 mph.
1.15 The speed of light in Crown glass is greater than its speed in
so the answer is easy it's air
if the fuel pellets in spent fuel rods do not have the plutonium removed, how long must that high-level radioactive waste be stored before it is considered safe
If the fuel pellets in spent fuel rods do not have the plutonium removed, the high-level radioactive waste must be stored for approximately 10,000 years before it is considered safe.
What is radioactive? Radioactive means that the nucleus of an atom is unstable and is continuously decaying to form a different nucleus, emitting radiation in the process. This radiation can be in the form of alpha particles, beta particles, or gamma rays.What are fuel pellets?Fuel pellets are a type of fuel that is made of small cylinders or pellets that have been compressed from natural uranium, mixed oxide, or plutonium dioxide powder. These pellets are then loaded into fuel rods to produce energy in nuclear reactors.What is plutonium?Plutonium is a radioactive, silvery-grey metallic element that is a by-product of nuclear fission reactions. It is a highly toxic substance and is considered one of the most dangerous materials on Earth because it can cause cancer and other diseases if ingested or inhaled.How long must the high-level radioactive waste be stored before it is considered safe?High-level radioactive waste from nuclear reactors must be stored for thousands of years before it is considered safe. This is because the waste is highly radioactive and can remain dangerous for a very long time. If the fuel pellets in spent fuel rods do not have the plutonium removed, the high-level radioactive waste must be stored for approximately 10,000 years before it is considered safe.
learn more about plutonium here:
https://brainly.com/question/13273771
#SPJ4
A glider on an airtrack is measured to have a momentum of -0.128 kgm/s in the x-direction (i.e., its momentum is directed to the left). If the glider is known to have a mass of 127.8 grams, what is the velocity of the glider?
What's the Solution?
The momentum is directed to the left, the velocity is negative. Therefore, the velocity of the glider is -1.002 m/s to the left.
The momentum of an object is defined as the product of its mass and velocity:
momentum = mass x velocity
In this case, we are given the momentum of the glider, its mass, and its direction of motion. We can use these values to solve for the velocity of the glider.
First, we convert the mass of the glider from grams to kilograms:
mass = 127.8 g = 0.1278 kg
Next, we use the formula for momentum to solve for the velocity of the glider:
momentum = mass x velocity
-0.128 kgm/s = 0.1278 kg x velocity
velocity = (-0.128 kgm/s) / (0.1278 kg)
velocity = -1.002 m/s.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ1
Look at the graph. What is the slope of the line?
Answer: B. 2
Explanation:
We will use the given formula to find the slope. Then, we will solve by substituting two points and simplifying.
[tex]\displaystyle \frac{y_{2} -y_{1} }{x_{2} -x_{1} } =\frac{8-4}{4-2}=\frac{4}{2} =2[/tex]
At first glance it may seem like a slope of one, but then we notice that the x-axis and y-axis have different scales. The slope of the line is 2.
Ray has two metal bars. He knows metal bar 1 is a magnet. How could he use metal bar 1 to find out if metal bar 2 is a magnet?
Ray could use metal bar 1 in a variety of ways to detect if metal bar 2 is a magnet.
Detecting a magnet with a magnetRay can use metal bar 1 (the magnet) to find out if metal bar 2 is also a magnet by performing the following steps:
Hold metal bar 1 near one end of metal bar 2 without touching it.Slowly move metal bar 1 along the length of metal bar 2.If metal bar 2 is also a magnet, it will attract or repel metal bar 1 as he moves it along its length.If metal bar 2 is not a magnet, there will be no attraction or repulsion between the two bars.Alternatively, Ray could also suspend metal bar 2 from a string and bring metal bar 1 near it. If metal bar 2 is a magnet, it will be attracted to metal bar 1 and start to swing towards it. If metal bar 2 is not a magnet, it will remain still.
More on magnets can be found here: https://brainly.com/question/2841288
#SPJ1
a 1 kg metal cube at 200 degrees celsius is added to a beaker with 1 kg of very 10 degree celsius water. the metal cools off, while the water warms up. what is the approximate temperature when they reach equilibrium.
The equilibrium temperature will be between 10°C (initial temperature of the water) and 200°C (initial temperature of the metal). The exact value depends on the specific heat capacity of the metal.
To find the equilibrium temperature, we can use the concept of heat transfer. The heat lost by the metal will be equal to the heat gained by the water.
Step 1: Determine the specific heat capacities (c) of metal and water.
c_water = 4,186 J/(kg·°C)
c_metal: we don't have the specific heat capacity, so let's call it c_m.
Step 2: Set up the heat transfer equation.
Q_metal = Q_water
Q = mcΔT
Step 3: Substitute the known values.
(1 kg)(c_m)(200 - T) = (1 kg)(4,186 J/(kg·°C))(T - 10)
Step 4: Solve for T, the equilibrium temperature.
Without knowing the specific heat capacity (c_m) of the metal, we cannot find the exact equilibrium temperature. However, we can say that the equilibrium temperature will be between 10°C (initial temperature of the water) and 200°C (initial temperature of the metal). The exact value depends on the specific heat capacity of the metal.
For more such questions on equilibrium , Visit:
https://brainly.com/question/517289
#SPJ11
how do astronomers measure that sunspots come in north pole / south pole magnetic pairs? how do they view the sun's magnetic field?
Astronomers measure sunspots and their magnetic polarity using a technique called spectropolarimetry. This method analyzes the interaction between the sun's magnetic field and its emitted light. To view the sun's magnetic field, scientists use instruments like magnetographs, which are specialized telescopes that detect and record the sun's magnetic activity.
Sunspots are cooler, darker areas on the sun's surface that possess intense magnetic activity. The Zeeman effect, a phenomenon where the magnetic field splits the spectral lines of light, is crucial in studying the sun's magnetic field. By observing these spectral lines and their shifts, astronomers can determine the strength and direction of the magnetic field in sunspots.
Sunspots typically occur in pairs with opposite magnetic polarities, one being the north pole and the other the south pole. These pairs are aligned in an east-west direction, with the leading sunspot having a magnetic polarity opposite to that of the sun's magnetic field at that particular solar hemisphere.
In summary, astronomers use spectropolarimetry and the Zeeman effect to analyze the sun's magnetic field and identify sunspots' polarities, while magnetographs provide visual representations of the magnetic field distribution.
For more such questions on Astronomers, click on:
https://brainly.com/question/2141924
#SPJ11
the cable is moved so that it is attached to a different point on the pole. if the new vertical force exerted by the wall is 0 n, where is the cable attached?
The cable is attached to the pole at the same height as the point where it connects to the wall. This creates a completely horizontal force and results in a 0 N vertical force exerted by the wall.
To determine where the cable is attached when the new vertical force exerted by the wall is 0 N, follow these steps:
1. Understand the situation: The cable is attached to a pole and exerts a vertical force on the wall. If the vertical force becomes 0 N, it means that the force is now completely horizontal.
2. Analyze the forces: Since the vertical force is 0 N, the force exerted by the cable must be completely horizontal. This means that the cable is exerting a force parallel to the ground.
3. Determine the attachment point: To exert a completely horizontal force, the cable must be attached to the pole at the same height as the point where it connects to the wall. This ensures that the cable is parallel to the ground, and the vertical force exerted by the wall is 0 N.
In conclusion, the cable is attached to the pole at the same height as the point where it connects to the wall. This creates a completely horizontal force and results in a 0 N vertical force exerted by the wall.
For more such questions on horizontal force , Visit:
https://brainly.com/question/12979825
#SPJ11
the diameters of the main rotor and tail rotor of a single-engine helicopter are 7.70 m and 1.01 m, respectively. the respective rotational speeds are 449 rev/min and 4,120 rev/min. calculate the speeds of the tips of both rotors.
The speed of the tips of the main rotor and tail rotor can be calculated by multiplying the rotational speed by the circumference of the rotor.
The circumference of a circle is equal to the diameter multiplied by pi (π). The speed of the main rotor tip is equal to 7.70 m x 449 rev/min x π = 2410.73 m/min. The speed of the tail rotor tip is equal to 1.01 m x 4,120 rev/min x π = 12,831.55 m/min.
The main rotor and tail rotor of a helicopter are responsible for providing lift and stability. The main rotor provides lift by creating a pressure differential between its upper and lower surfaces. The tail rotor counters the torque generated by the main rotor by providing thrust in the opposite direction.
The speed of the rotor tips directly affects the performance of the helicopter and has a significant impact on the aircraft’s safety. As such, it is important to ensure that the rotor tips are spinning at the correct speeds.
know more about Speed here
https://brainly.com/question/30462853#
#SPJ11
a source emits sound with frequency of 100 hz. what is the relative velocity between the sound and observer
The relative velocity between the sound and the observer is the same as the speed of sound, which is 343 m/s. To calculate the relative velocity between the sound and the observer, we first need to know the speed of sound in the medium through which the sound is traveling.
Assuming the sound is traveling through air at room temperature, the speed of sound is approximately 343 meters per second (m/s).
Given the frequency (f) of 100 Hz, we can find the wavelength (λ) of the sound wave using the formula:
Speed of sound (v) = Frequency (f) × Wavelength (λ)
Rearranging the formula to find the wavelength:
Wavelength (λ) = Speed of sound (v) / Frequency (f)
Now, we can plug in the values:
λ = 343 m/s / 100 Hz = 3.43 meters
The relative velocity between the sound and the observer is the same as the speed of sound, which is 343 m/s. The frequency and wavelength of the sound do not affect the relative velocity between the sound and the observer.
To know more about relative velocity, refer here:
https://brainly.com/question/29655726#
#SPJ11
unit 3 progress check frq ap phyics
bro there's no question
as the person climbs the ladder, what happens to the magnitude of the normal contact force acting on the top end of the ladder due to the wall as long as the ladder doesn't slip?
As the person climbs the ladder, the magnitude of the normal contact force acting on the top end of the ladder due to the wall increases, as long as the ladder doesn't slip.
This is because the normal force acting on the ladder is a reaction force to the weight of the ladder and the person. As the person climbs higher up the ladder, the weight of the person+ladder system also increases. This results in an increase in the force required to maintain static equilibrium, which is provided by the normal force from the wall acting on the ladder. However, if the coefficient of static friction between the ladder and the wall is not high enough, the ladder may slip and the normal force acting on the ladder will decrease. But as long as the ladder doesn't slip, the magnitude of the normal contact force acting on the top end of the ladder due to the wall will increase as the person climbs higher up the ladder.
Learn more about ladder here:
https://brainly.com/question/28636911
#SPJ4
scientists believe that long-runout debris flows are able to travel long distances because the jostling back and forth of fragments in the flow creates sound waves that propagate through the material, making it behave like a fluid. this process is known as
This process involves sound waves that propagate through the material, making it behave like a fluid. The process described in the question is known as liquefaction.
which is the process by which solid soil or rock is transformed into a liquid-like state due to changes in pressure, stress, or other factors.
The term liquefaction is commonly used in the fields of geology, engineering, and materials science, and it refers to a wide range of phenomena in which solid materials become fluid-like due to the application of external forces.
In the case of long-runout debris flows, the jostling back and forth of fragments in the flow creates sound waves that cause the material to behave like a fluid, allowing it to travel long distances.
For more such questions on liquefaction
brainly.com/question/4067457
#SPJ11
at what angle in degrees is the first-order maximum for 455-nm wavelength blue light falling on double slits separated by 0.0550 mm?
At 0.474 degrees angle the first-order maximum for 455-nm wavelength blue light falling on double slits separated by 0.0550 mm.
Using the formula for the first-order maximum in a double-slit experiment, we have:
sin(θ) = (mλ) / d
where θ is the angle of the first-order maximum, m is the order number (1 for first-order maximum), λ is the wavelength of the light (455 nm), and d is the separation between the slits (0.0550 mm).
First, let's convert the units: λ = 455 nm = 455 x 10^(-9) m, and d = 0.0550 mm = 0.0550 x 10^(-3) m.
Now, we can calculate sin(θ):
sin(θ) = (1)(455 x 10^(-9) m) / (0.0550 x 10^(-3) m)
sin(θ) ≈ 0.00827273
To find the angle θ in degrees, we take the inverse sine (arcsin) of the calculated value:
θ ≈ arcsin(0.00827273) ≈ 0.474 degrees
For more such questions on angle, click on:
https://brainly.com/question/29506154
#SPJ11
a mass of 2.30 kg is attached to a 1,460 n/m spring as shown. when the mass is pushed down and released, the system begins to oscillate. what is the period of oscillation of this system, in seconds?
The mass attached to a 1,460 N/m spring will have a period of oscillation of 0.80 seconds. The period of oscillation of this system will be 0.80 seconds.
The mass attached to a 1,460 N/m spring will have a period of oscillation of 0.80 seconds.What is an oscillation?Oscillation is the repetitive variation of a variable around an equilibrium value. The motion of a body or system that varies between two points is called oscillation. A spring attached to a mass will make it oscillate when compressed and released.What is the formula to find the period of oscillation of a spring mass system?The formula for finding the period of oscillation of a spring-mass system is as follows:T = 2π√m/kwhere:T is the period of oscillationk is the spring constantm is the mass attached to the springSubstituting the values in the formula:T = 2π√m/kT = 2π√2.3/1460T = 2π√0.00158T = 0.80 seconds.
Learn more about The mass here:
https://brainly.com/question/15712153
#SPJ4
what is the angular momentum of a 0.310 kg ball rotating on the end of a thin string in a circle of radius 1.05 m at an angular speed of 11.9 rad/s ?
The angular momentum of a 0.310 kg ball rotating on the end of a thin string in a circle of radius 1.05 m at an angular speed of 11.9 rad/s is 3.32 kg.m²/s.
Angular momentum is the rotational equivalent of linear momentum. It is defined as the moment of momentum of an object, given by the product of its moment of inertia and its angular velocity. Mathematically, Angular momentum = moment of inertia × angular velocity Where, a moment of inertia = mass × radius²In this problem, a 0.310 kg ball is rotating on the end of a thin string in a circle of radius 1.05 m at an angular speed of 11.9 rad/s.
The moment of inertia of the ball can be calculated as, a moment of inertia = mass × radius²= 0.310 × (1.05)²= 0.342255 kg.m²Substituting the given values in the formula of angular momentum, we get, angular momentum = moment of inertia × angular velocity= 0.342255 × 11.9= 3.32 kg.m²/s Therefore, the angular momentum of the ball is 3.32 kg.m²/s.
Know more about momentum here:
https://brainly.com/question/18798405
#SPJ11
starting from very far away, an object is moved closer and closer to a diverging lens, eventually reaching the lens. what happens to its image? (there could be more than one correct choice.) a) the image gets closer and closer to the lens. b) the image gets farther and farther from the lens. c) the image always remains virtual. d) the image eventually changes from real to virtual. e) the image keeps getting larger and larger.
The correct answers are A, C and E.
As the object moves closer and closer to the lens, the image gets closer and closer to the lens (A) and gets larger and larger (E).
The image will always remain virtual (C), as diverging lenses cannot produce real images. When the object is very close to the lens, the image might appear real, but it will always be a virtual image since it is not located on the other side of the lens, like a real image would be. Therefore, the image does not change from real to virtual (D).
know more about Virtual image here
https://brainly.com/question/12538517#
#SPJ11
Lightning strikes the ground. The cloud and bolt had a negative charge. What charge did the ground have?
Explain.
The ground typically has a positive charge when a lightning strike occurs. This is because lightning results from the discharge of excess electrical energy between two charged regions, with one being negatively charged (the cloud) and the other positively charged.
What causes lightning strikes to occur?Lightning strikes occur due to the discharge of excess electrical energy between two charged regions, typically between a negatively charged cloud and a positively charged ground.
How does lightning affect the environment?Lightning can cause wildfires, power outages, and damage to infrastructure. It can also release nitrogen oxides into the atmosphere, which contribute to air pollution and can have negative effects on human health and the environment.
However, lightning can also provide beneficial effects by helping to replenish the ozone layer and providing nitrogen to plants.
To know more about lightning,visit:
https://brainly.com/question/16854009
#SPJ1
when a camera remains in place but gradually moves to a closer or wider view of a scene, this is called
When a camera remains in place but gradually moves to a closer or wider view of a scene, this is called a zoom.
A camera zoom is a cinematic effect that can be used to create a feeling of drama, movement, or excitement. It involves changing the focal length of a lens to make the subject appear closer or farther away without physically moving the camera itself.
When a camera remains in place but gradually moves to a closer or wider view of a scene, this is called a zoom.
Learn more about wider here:
https://brainly.com/question/17134093
#SPJ4
A 5.00kg box slides down a frictionless plane at an angle of 60.0°. What is the magnitude of the box's acceleration and the normal force on the box?
Explanation:
Normal force is mg cos Φ = 5 (9.81) cos (60) = 9.9 N
acceleration
F = ma the downplane force = mg sin Φ
5 * 9.81 sin (60) = 5 (a)
a = 8.5 m/s^2
a straight wire produces a magnetic field of 4 t at a distance of 4 cm from the wire. what is the magnetic field at a distance of 8 cm from the wire? group of answer choices 4 t
The magnetic field at a distance of 8 cm from the wire is 2 T.
The magnetic field at a distance of 8 cm from a straight wire can be determined using the formula for the magnetic field produced by a straight wire:
B = μ₀I / (2πr), where B is the magnetic field, μ₀ is the permeability of free space, I is the current in the wire, and r is the distance from the wire.
Given that the magnetic field is 4 T at a distance of 4 cm, we can first find the current in the wire:
4 T = μ₀I / (2π(0.04 m))
Now, we can use the same formula to find the magnetic field at a distance of 8 cm (0.08 m):
B = μ₀I / (2π(0.08 m))
Since the current in the wire is the same, we can notice that the only difference between the two equations is the distance (r). The relationship between the magnetic field and distance is inverse, so when the distance is doubled (from 0.04 m to 0.08 m), the magnetic field will be halved.
Therefore, the magnetic field at a distance of 8 cm from the wire is 4 T / 2 = 2 T.
To know more about magnetic field, refer here:
https://brainly.com/question/11514007#
#SPJ11