The resistivity of the wire material can be calculated using Ohm's Law, which states that V=IR, or voltage = current multiplied by resistance. Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8} \Omega m[/tex].
Resistivity of wire is given as ρ=RA/L where R is the resistance of wire, A is the cross-sectional area of the wire, L is the length of the wire.
The formula to calculate the resistance of wire from Ohm's Law is given by R=V/I where V is the voltage, I is the current.
Substituting the given values: V = 12.0 V, I = 7.5 A.
Therefore, R=V/I=12.0 / 7.5 = 1.6 Ω
From the formula of resistivity:
[tex]\rho=\dfrac{RA}{L}\\R=\dfrac{ρL}{A}[/tex]
Substituting the given values: R = 1.6 Ω, L = 11.0 m and calculating the area:
[tex]A = (1.8 \times 10^{-3} m) (0.11 \times 10^{-3} m)\\ = 0.198 \times 10^{-6} m²[/tex]
Therefore,
[tex]\rho = RA/L\\= \dfrac{R \times A}{ L}\\= \frac{1.6 \times 0.198 \times 10^{-6}}{ 11.0}\\ = 2.87 \times 10^{-8 } \Omega m[/tex]
Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8 } \Omega m[/tex].
For more details on resistivity, click on the below link:
https://brainly.com/question/30799966
#SPJ11
The average wavelength in a series of ocean waves is 15. 0 meters. A wave crest arrives at the shore an average of every 10. 0 seconds, so the frequency is 0. 100 Hz. What is the average speed of the waves?
A wave crest arrives on the shore a median of every 10. zero seconds, so the frequency is 0. one hundred Hz. The average speed of the waves is 1.five m/s.
We are to decide the common pace of the waves.
Using the formula
v = fλ
Where
v is the speed
f is the frequency
and λ is the wavelength
From the given information
f = 0.1 Hz
λ = 15.0 m
∴ Speed of the wave = 0.1 × 15.0
Speed of the wave = 1.5 m/s
Average speed is defined as the total distance traveled by an object divided by the time taken to cover that distance. It is the measure of the average rate at which an object covers a certain distance in a given amount of time. Mathematically, the average speed is expressed as: Average speed = Total distance traveled / Time taken
It is important to note that average speed is not the same as instantaneous speed, which refers to the speed of an object at a particular instant in time. Average speed takes into consideration the entire adventure, while instant velocity only reflects the velocity at a unmarried moment. The unit of measurement for average speed is meters per second (m/s) or kilometers per hour (km/h), depending on the system of measurement used.
To know more about Average speed visit here:
brainly.com/question/12322912
#SPJ4
assume 100 units of energy enters the earth atmosphere system at the top of the atmosphere (toa). how much energy leaves the system?
The amount of energy that leaves the Earth's atmosphere system is 100 units of energy.
According to the conservation of energy principle, energy can neither be created nor destroyed, it can only be transformed from one form to another. Therefore, the energy that enters the Earth's atmosphere system is absorbed, reflected, and emitted as heat.
In simpler terms, some of the energy is reflected back into space, some of it is absorbed by the Earth's surface and is emitted back as heat, and some of it is trapped by greenhouse gases in the atmosphere. Ultimately, the amount of energy that leaves the system is approximately equal to the amount of energy that enters the system.
Thus, the amount of energy that leaves the Earth's atmosphere system is 100 units of energy.
To know more about greenhouse gases click here:
https://brainly.com/question/14131369
#SPJ11
a 240 g air-track glider is attached to a spring. the glider is pushed in 8.2 cm against the spring, then released. a student with a stopwatch finds that 14 oscillations take 11.0 s . What is the spring constant?
The spring constant is 0.28 N/m if 14 oscillations take 11.0s.
In physics, oscillations are defined as a repetitive variation, typically in time, of some measure about a central value (often a point of equilibrium) or between two or more different states. The spring constant (k) is a measure of a spring's stiffness. It is the amount of force required to displace a spring a specific distance (typically one meter).
The spring constant formula is expressed as:-
F=kx
where k is the spring constant and x is the displacement produced by the force F.
We know that the air-track glider has a mass of 240 g, and it is attached to a spring. The glider is pushed 8.2 cm against the spring and then released. The oscillations are then observed, and it is found that 14 oscillations occur in 11.0 s.
We can calculate the spring constant by using this information.
Let us now calculate the spring constant k.
For a mass (m) attached to a spring, the formula for the time period T is:-
T=2π√m/k
We know that the time period T = 11/14 s. We also know that the glider has a mass of 240 g or 0.24 kg.
Now, we can solve the formula for the spring constant k as follows:-
k= 4π²m/T²k = 4π² × 0.24 kg / (11/14 s)²k = 0.28 N/m
Therefore, the spring constant is 0.28 N/m.
Learn more about oscillations: https://brainly.com/question/27237546
#SPJ11
at time an object is traveling to the right along the axis at a speed of with acceleration which statement is true? (a) the object will slow down, eventually coming to a complete stop. (b) the object cannot have a negative acceleration and be moving to the right. (c) the object will continue to move to the right, slowing down but never coming to a complete stop. (d) the object will slow down, moment
The statement that is true for an object traveling to the right along the axis at a speed of with acceleration is "the object will slow down, eventually coming to a complete stop. So, Option A is correct.
Kinetic Friction is the resistive force that opposes the movement or motion of two interacting surfaces in relative motion. It is due to the interactions between surfaces when there is some movement between the two. The frictional force opposes the motion of the object and tends to bring it to a halt or slow it down.
Let us now consider the given options:
(a) The object will slow down, eventually coming to a complete stop. This statement is true. The object will slow down and come to a complete stop.
(b) The object cannot have a negative acceleration and be moving to the right. Thus, this statement is not true. The object can have a negative acceleration and still be moving to the right.
(c) The object will continue to move to the right, slowing down but never coming to a complete stop. Thus, this statement is not true. The object will come to a complete stop.
(d) The object will slow down, moment. Thus, this statement is not complete. It does not explain what will happen after slowing down.
Therefore, option (a) is the correct option.
To know more about Kinetic Friction, refer here:
https://brainly.com/question/30886698#
#SPJ11
a 5-kg shark swimming at 1 m/s swallows an absent-minded 1-kg fish swimming toward it at 4 m/s. the speed of the shark after his meal is
The speed of the shark after it swallows the fish is calculated using the conservation of momentum principle. The total momentum before the collision is 5 kg * 1 m/s + 1 kg * 4 m/s = 9 kg * m/s. The total momentum after the collision is 5 kg * v, where v is the speed of the shark after the collision. Therefore, v = 9/5 m/s = 1.8 m/s. Thus, the speed of the shark after it swallows the fish is 1.8 m/s.
The speed of the shark after it has swallowed the 1-kg fish swimming toward it at 4 m/s is 3 m/s. This can be determined by conservation of momentum. Momentum is a vector quantity, meaning that the direction of the momentum must also be taken into account.
In this situation, the momentum of the shark before it swallows the fish is 5 kg⋅m/s due to its velocity of 1 m/s. After the shark has eaten the fish, the momentum is 6 kg⋅m/s due to the addition of the fish's momentum of 4 kg⋅m/s. Since momentum is conserved, the momentum of the shark after eating the fish is the same as the momentum of the shark before eating the fish. Since the mass of the shark does not change, the velocity must change to balance out the difference in momentum. This means that the velocity of the shark after eating the fish is 3 m/s.
For more equations related to momentum.
https://brainly.com/question/30677308
#SPJ11
how much heat is lost through a 3' x 5' single-pane window with a storm that is exposed to a temperature differentia
The amount of heat lost through a 3' x 5' single-pane window with a storm that is exposed to a temperature differential is 108 BTU per hour.
The U-factor is a measure of how well a window insulates against heat transfer. The lower the U-factor, the better the window insulates.
The temperature difference is the difference between the inside and outside temperatures.The area of the window is the size of the window.Using these factors, we can calculate the rate of heat loss through the window in units of BTUs per hour.
Assuming a U-factor of 1.2 and a temperature difference of 60°F, the calculation would be:
Heat Loss = 1.2 BTU/(hrft^2F) x 15 ft^2 x 60°F
Heat Loss = 108 BTU/hour
Therefore, the heat lost through the window is 108 BTU per hour.
To know more about heat loss click here:
https://brainly.com/question/14228650
#SPJ11
Complete Question:
How much heat is lost through a 3' × 5' single-pane window with a storm that is exposed to a 60 Fahrenheit temperature differential?
a heavy fish (mass 4 kg) is swimming with a speed of 1.5 m/s. he then swallows a light fish (1.2 kg), swimming toward him with a speed of 3.0 m/s. what is the velocity of the larger fish after he had his meal? (you can neglect water resistance.)
The velocity of the larger fish after the meal is zero.
We can use the law of conservation of momentum, which states that the total momentum of a closed system remains constant. Before the light fish is swallowed, the total momentum is,
p1 = m1v1 + m2v2
where m1 = 4 kg, v1 = 1.5 m/s (velocity of the heavy fish), m2 = 1.2 kg, and v2 = -3.0 m/s (negative because the light fish is swimming toward the heavy fish).
p1 = (4 kg)(1.5 m/s) + (1.2 kg)(-3.0 m/s)
p1 = 0 kg m/s
After the light fish is swallowed, the two fish become one system. Let the velocity of the larger fish after the meal be v.
The total momentum of the system after the meal is,
p2 = (m1 + m2)v
By the law of conservation of momentum, p1 = p2,
0 kg m/s = (4 kg + 1.2 kg) v
Solving for v,
v = 0 m/s
To know more about speed, here
brainly.com/question/31080132
#SPJ4
A pole-vaulter clears a crossbar and takes 1.0 s to fall from the apex of his flight to the landing pit. What was his downward vertical velocity at the end of this second? a. 4.9 m/s b. 9.81 m/s c. 1.0 m/s d. 19.62 m/s
The pole vaulters downward vertical velocity at the end of this second is. 9.81 m/s. The correct option is b.
When an object falls freely under gravity, its velocity increases at a constant rate of 9.81 m/s^2. This acceleration due to gravity is denoted by 'g' and has a magnitude of 9.81 m/s^2 on the surface of the Earth.
In the given problem, the pole-vaulter is falling freely under gravity after clearing the crossbar. The time taken for him to fall is 1.0 s. Therefore, his final downward velocity can be calculated using the formula:
v = g * t
where v is the final velocity, g is the acceleration due to gravity, and t is the time taken for the fall.
Substituting the values, we get:
v = 9.81 m/s^2 * 1.0 s = 9.81 m/s
Therefore, the downward vertical velocity of the pole-vaulter at the end of the second is 9.81 m/s, which is the answer (option b).
To know more about vertical velocity, refer here:
https://brainly.com/question/30559316#
#SPJ11
a second identical block is dropped onto the first from a height of 4.20 m m above the first block and sticks to it. what is the maximum elastic potential energy stored in the spring during the motion of the blocks after the collision? express your answer with the appropriate
The maximum elastic potential energy stored in the spring during the motion of the blocks after the collision is 164 J.
Since the two blocks stick together after the collision, they move together as a single mass. We can use conservation of energy to find the maximum elastic potential energy stored in the spring during the motion of the blocks after the collision.
Initially, the system has potential energy due to the gravitational field:
[tex]U_i = mgh[/tex]
where m is the total mass of the system, g is the acceleration due to gravity, and h is the initial height of the second block above the first.
When the blocks hit the spring, they compress it and store elastic potential energy. At the point of maximum compression, all of the initial potential energy has been converted to elastic potential energy:
[tex]U_e = (1/2)kx^2[/tex]
where k is the spring constant and x is the maximum compression of the spring.
By conservation of energy, the initial potential energy must be equal to the maximum elastic potential energy:
[tex]U_i = U_emgh = (1/2)kx^2[/tex]
Solving for x, we get:
[tex]x = sqrt(2mgh/k)[/tex]
The spring reaches its maximum compression when the blocks momentarily come to rest. At this point, all of the initial potential energy has been converted to elastic potential energy, so the maximum elastic potential energy is:
[tex]U_e = (1/2)kx^2 = (1/2)k(2mgh/k) = mgh[/tex]
Substituting the given values, we get:
[tex]U_e = (2.00 kg + 2.00 kg)(9.81 m/s^2)(4.20 m) = 164 J[/tex]
Therefore, the maximum elastic potential energy stored in the spring during the motion of the blocks after the collision is 164 J.
To know more about "- potential energy here
https://brainly.com/question/16705765
#SPJ4
Fill in the blank:the equilibrium constant, k, relates quantity of products to reactants at a point when the reaction is ____.
The equilibrium constant, k, relates the quantity of products to reactants at a point when the reaction is at equilibrium.
What is equilibrium?Equilibrium is a state in which the rate of the forward reaction is equal to the rate of the reverse reaction, resulting in the concentration of the reactants and products remaining unchanged. A reaction is said to be in equilibrium when it has reached a state of dynamic balance.
The equilibrium constant (Kc) is a measure of the extent to which a reaction proceeds to form products. The equilibrium constant is a ratio of the concentration of the products to the concentration of the reactants at equilibrium. The value of Kc varies with temperature and depends on the stoichiometry of the balanced chemical equation.
The larger the value of Kc, the greater the concentration of products relative to reactants at equilibrium. Similarly, a smaller value of Kc indicates a greater concentration of reactants at equilibrium. The equilibrium constant is useful in predicting the direction in which a chemical reaction will proceed.
If the value of Kc is greater than one, the equilibrium favors the products, and if the value of Kc is less than one, the equilibrium favors the reactants. If the value of Kc is equal to one, the reaction is said to be at equilibrium, and the concentration of the reactants and products is equal.
To know more about equilibrium refer here:
https://brainly.com/question/30694482#
#SPJ11
a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet. the coefficients of static and kinetic friction are 0.6 and 0.4, respectively. the worker pushes with a force of 600 n. the frictional force exerted by the surface is
When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface on the crate is 588 N.
When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface can be calculated as follows:
The weight of the crate = m × g = 100 kg × 9.8 m/s² = 980 N
Force applied by the worker = F = 600 N
The force of friction acting on the crate is given by the following formula:
Ff = μF
Where, μ is the coefficient of friction, F is the normal force acting on the crate.
Notes: The normal force is equal and opposite to the weight of the crate. i.e., N = 980 N1. The frictional force exerted by the surface on the crate is the static frictional force initially. Hence, we use the coefficient of static friction for our calculation.
2. If the force applied by the worker is not enough to overcome the static frictional force, then the crate will not move and the frictional force will remain static friction.
3. Once the crate starts moving, the static friction will convert to kinetic friction. Hence, we will use the coefficient of kinetic friction if the force applied by the worker is greater than the force of static friction. Initially, the force applied by the worker is less than the force of static friction, hence the frictional force exerted on the crate will be the static frictional force.
Frictional force = Ff = μN
The normal force acting on the crate = Weight of the crate = 980 N
Frictional force =
Ff = μN
= 0.6 × 980 N
= 588 N
Therefore, the frictional force exerted by the surface on the crate is 588 N.
For more such questions on frictional force , Visit:
https://brainly.com/question/4618599
#SPJ11
what must the charge (sign and magnitude) of a particle of mass 1.45 g be for it to remain stationary when placed in a downward-directed electric field of magnitude 700 n/c ?
The charge (sign and magnitude) of a particle of mass 1.45 g must be for it to remain stationary when placed in a downward-directed electric field of magnitude 700 n/c is -1.029x10⁻⁴ C.
The magnitude of the charge must be equal to the magnitude of the electric field (700 n/c).
Therefore, we can write:-mg = qE
where, m = 1.45g = 1.45 x 10⁻³ kg
E = 700 N/cm = 1.45 x 10⁻³ kg x 9.81 m/s²
= 0.01419 N (Weight of the particle)
q = -1.029 x 10⁻⁴ C
To remain stationary when placed in a downward-directed electric field of magnitude 700 n/c, the charge (sign and magnitude) of a particle of mass 1.45 g must be negative.
Learn more about the Charge of a particle here:
https://brainly.com/question/28233928
#SPJ11
what is the term for an orbit that electrons occupy at a fixed distance from the nucleus; designated 1, 2, 3, 4 ...? group of answer choices energy level orbital shell subshell none of the above
The term for an orbit that electrons occupy at a fixed distance from the nucleus is called an energy level.
What are energy levels?Electrons occupy specific energy levels in an atom, which are determined by the amount of energy required to move an electron from its present energy level to the next higher energy level. The energy levels are designated by a number, which ranges from one to seven. The lowest energy level is one, and the highest energy level is seven.
Electrons in the first energy level are the closest to the nucleus, while electrons in the seventh energy level are the farthest away.
Learn more about energy levels here: https://brainly.com/question/14287666.
#SPJ11
when 115 v is applied across a wire that is 10 m long and has a 0.30 mm radius, the magnitude of the current density is 1.4 x 108 find the resisitivty of the wire
When 115 V is applied across a wire that is 10 m long and has a 0.30 mm radius, the magnitude of the current density is 1.4 x [tex]10^{-8}[/tex] A/m2, therefore the resistivity of the wire is 8.214 x [tex]10^{-8}[/tex] Ω m
How To Calculate The Resistivity Of The Wire?The resistivity of the wire can be calculated using the formula ρ = E/J, where ρ is the resistivity, E is the electric field, and J is the current density. The electric field E can be calculated using the formula E = V/L, where V is the voltage applied and L is the length of the wire. Thus, E = 115 V/10 m = 11.5 V/mThe current density J is given as1.4 x [tex]10^{-8}[/tex] A/m2. Using the formula,ρ = E/J= 11.5 V/m/1.4 x 108 A/m2= 8.214 x [tex]10^{-8}[/tex] Ω m.
Therefore, the resistivity of the wire is 8.214 x [tex]10^{-8}[/tex] Ω m. The resistivity of a material is a measure of its ability to oppose the flow of electric current. It is defined as the resistance per unit length and cross-sectional area of a wire. The resistivity of a material depends on various factors, including its chemical composition, temperature, and impurities. It is an important property of materials used in electrical and electronic applications.
Learn more about the resistivity at https://brainly.com/question/17010736
#SPJ11
a 3.52 volt potential difference is placed across a 1,829.90 ohm resistor. how many electrons pass through the resistor in 3.85 seconds?
Given that a 3.52 volt potential difference is applied to a 1,829.90 ohm resistor, the current that passes through the resistor can be calculated by using Ohm's law. According to Ohm's law, current is equal to the potential difference divided by the resistance, so the current that passes through the resistor is 3.52 volts / 1,829.90 ohms = 0.0019265 amps.
Next, the number of electrons that pass through the resistor in 3.85 seconds can be calculated. The number of electrons is equal to the current multiplied by the time. So, 0.0019265 amps x 3.85 seconds = 7.43 x 10^-5 coulombs. Since one coulomb is equal to 6.24 x 10^18 electrons, the number of electrons that pass through the resistor in 3.85 seconds is 7.43 x 10^-5 x 6.24 x 10^18 = 4.6 x 10^13 electrons.
Know more about Ohm's law here
https://brainly.com/question/1247379#
#SPJ11
a stone is thrown upward from ground level. the initial speed is 176 feet per second. how high will it go?
The stone thrown upward from ground level with an initial speed of 176 feet per second will reach a maximum height of: approximately 564 feet
To calculate the maximum height, we must use the equation of motion, which states that the final velocity is equal to the initial velocity plus the acceleration times the time. We know the initial velocity (176 feet per second) and the acceleration is equal to the acceleration due to gravity, which is -32 feet per second squared.
Since we do not know the time, we can solve it using the equation Vf = Vi + at. Solving for t, we get[tex]t = (Vf-Vi)/a[/tex], where Vf is 0 and Vi is 176 feet per second. Thus,[tex]t = (0-176)/(-32)[/tex], and t = 5.5 seconds.
Using the equation of motion, we can find the maximum height by using the equation [tex]H = Vi*t + (1/2)*a*t^2[/tex]. We plug in our values and get[tex]H = 176*5.5 + (1/2)*(-32)*5.5^2 = 564 feet.[/tex]
Therefore, the stone thrown upward from ground level with an initial speed of 176 feet per second will reach a maximum height of approximately 564 feet.
To know more about speed refer here:
https://brainly.com/question/28224010#
#SPJ11
old faithful geyser in yellowstone national park shoots water every hour to a height of 40.0 m. with what velocity does the water leave the ground?
The velocity with which the water leaves the ground is 28.0 m/s (downward).
The Old Faithful Geyser in Yellowstone National Park shoots water every hour to a height of 40.0 meters.
To find the velocity with which the water leaves the ground, we can use the following kinematic equation:
v² = u² + 2as
Here,
v = final velocity
u = initial velocity
a = acceleration due to gravity
s = distance traveled by the object
The initial velocity of the water when it leaves the ground is 0 m/s.
Also, we can assume the final velocity of the water when it reaches the maximum height to be 0 m/s.
We know that the acceleration due to gravity is -9.8 m/s² (negative due to the direction).
The distance traveled by the water is the height to which it rises, i.e., 40.0 meters.
Using the above values in the kinematic equation, we get:
v² = 0² + 2*(-9.8)*40.0v² = -784v = √(-784)
Since the answer is coming out to be negative, it indicates that the velocity is in the downward direction.
So, the velocity with which the water leaves the ground is 28.0 m/s (downward).
To know more about velocity, refer here:
https://brainly.com/question/30559316#
#SPJ11
at what angle of deflection makes the magnetic field strngth produced by the coil of the wire equal to the ambient magnetic field
The magnetic field strength created by the wire coil is equivalent to the ambient magnetic field when it is deflected at a right angle.
The magnetic field strength created by the wire coil is equivalent to the ambient magnetic field when it is deflected at a right angle. The Biot-Savart Law, which relates magnetic field strength to the current in a wire and the distance from the wire, applies to a wire coil.
The strength of the magnetic field generated by a current-carrying wire is proportional to the current in the wire and the number of turns per unit length. The magnetic field's intensity is determined by the number of turns in the wire coil, the current in the wire coil, the radius of the coil, and the permeability of free space.
The equation for calculating the magnetic field strength at a point in space around a current-carrying wire is given by the Biot-Savart Law:
B = µ₀I/2πr.
Where µ₀ is the permeability of free space, I is the current, and r is the distance from the wire to the point where the magnetic field strength is to be calculated.
Learn more about Biot-Savart Law at https://brainly.com/question/29564274
#SPJ11
describe how milliamperage influences the quantity of the xray beam and identify the range of milliamperage required for dental imaging
Milliamperage (mA) influences the quantity of the X-ray beam by controlling the amount of current passing through the X-ray tube. For dental imaging, the range of milliamperage required typically falls between 7 mA and 15 mA.
Milliamperage refers to the current or quantity of electrons moving through the x-ray tube to produce radiation. The milliamperage is responsible for controlling the amount of x-rays produced in a given time period. Radiation intensity is directly proportional to the milliamperage.
A higher milliamperage results in a greater number of electrons passing through the x-ray tube, which creates more x-rays. The milliamperage controls the quantity of radiation produced by the x-ray beam. Dental x-ray machines are designed with a pre-set milliamperage range that is appropriate for dental imaging.
Know more about Dental x-ray machines here:
https://brainly.com/question/29789903
#SPJ11
a perfectly elastic spring requires 0.54 jof work to stretch 6 cm from its equilibrium position. (a) what is its spring constant k? (b) how much work is required to stretch it an additional 6 cm?
The work required to stretch the elastic spring an additional 6 cm is 2.16 J.
(a) To find the spring constant k, we can use the formula:
[tex]W = (1/2) k x^2[/tex]
where W is the work done, k is the spring constant, and x is the displacement from the equilibrium position. Rearranging this formula to solve for k, we get:
[tex]k = 2W / x^2[/tex]
Substituting the given values, we have:
[tex]k = 2(0.54 J) / (0.06 m)^2[/tex]
k = 300 N/m
Therefore, the spring constant of the elastic spring is 300 N/m.
(b) To find the work required to stretch the spring an additional 6 cm, we can use the same formula:
[tex]W = (1/2) k x^2[/tex]
where x is the additional displacement from the equilibrium position. The total displacement from the equilibrium position is 6 cm + 6 cm = 12 cm = 0.12 m.
Substituting the values, we have:
[tex]W = (1/2) (300 N/m) (0.12 m)^2W = 2.16 J[/tex]
To know more about " elastic springs. here
https://brainly.com/question/28997611
#SPJ4
horses that move with the fastest linear speed on a merry-go-round are located anywhere, because they all move at the same speed. near the center. near the outside.
Horses that move with the fastest linear speed on a merry-go-round are located near the outside.
A merry-go-round is an amusement park ride that comprises a rotating circular platform equipped with seats or mounts for people to ride on. When the ride is operating, the circular platform rotates around a fixed central axis at a constant velocity, while the people on it rotate with the platform. Linear speed refers to the velocity of the object in a straight line path, regardless of its direction of movement.
Therefore, the linear speed of the mounts on the merry-go-round depends on the radius of the circular path they move on. The closer the horse is to the center, the shorter the path it has to cover during one rotation of the platform, meaning it has a slower linear speed. Conversely, the farther the horse is from the center, the longer the path it has to cover, hence it has a faster linear speed. As a result, the mounts located near the outside of the merry-go-round move with the fastest linear speed.
Learn more about the linear speed at:
https://brainly.com/question/12707353
#SPJ11
A resistor and a capacitor are connected in series across an ideal battery. At the moment contact is made with the battery the voltage across the capacitor is
a. equal to the battery's terminal voltage. b. less than the battery's terminal voltage, but greater than zero. c. zero.
When a resistor and a capacitor are connected in series across an ideal battery, the voltage across the capacitor is zero at the moment contact is made with the battery.
The correct option is c.
An ideal battery is a voltage source that delivers a constant voltage regardless of the load resistance or current drawn from it.
An ideal battery can maintain a steady voltage regardless of the amount of current being drawn from it.
In real-life batteries, there is always some internal resistance, which causes the voltage to drop as the current increases.
A resistor is an electrical component that opposes or limits the flow of electrical current. It has two terminals and can be made of various materials like carbon, metal, and ceramic. It is used in various applications, including voltage dividers, current limiting, and biasing.
A capacitor is an electronic component that stores energy in an electric field between two charged conductors. It has two terminals and is made of two conducting plates separated by an insulating material called a dielectric.
Capacitors are used in various applications, including energy storage, timing circuits, and power conditioning.
To Learn more :
https://brainly.com/question/17134302
#SPJ11
which has a greater buoyant force on it, a 45.0- cm3 c m 3 piece of wood floating with part of its volume above water or a 45.0- cm3 c m 3 piece of submerged iron
A 45.0-cm3 piece of submerged iron will experience a greater buoyant force than a 45.0-cm3 piece of wood floating with part of its volume above water.
The buoyant force refers to the upward force that an object in a fluid experiences due to the pressure difference between the top and bottom of the object. Archimedes' principle states that the buoyant force on an object is equivalent to the weight of the fluid displaced by the object. The buoyant force is proportional to the volume of the object submerged in the fluid.
A submerged object displaces its weight of fluid, whereas a floating object displaces its own weight of fluid. Since iron has a higher density than water, a 45.0-cm3 piece of submerged iron will displace more water and experience a greater buoyant force than a 45.0-cm3 piece of wood floating with part of its volume above water.
for such more question on buoyant force
https://brainly.com/question/15706301
#SPJ11
find the net work w done on the particle by the external forces during the particle's motion.express your answer in terms of f and s . gg done on the particle by the external forces during the particle's motion. to understand the meaning and possible applications of the work-energy theorem. in this problem, you will use your prior knowledge to derive one of the most important relationships in mechanics: the work-energy theorem. we will start with a special case: a particle of mass m moving in the x direction at constant acceleration a . during a certain interval of time, the particle accelerates from vi to vf , undergoing displacement is given by s
The net work (W) done on the particle by the external forces during its motion can be expressed in terms of the initial (Ki) and final (Kf) kinetic energies as: [tex]W = ((1/2) \times m \times vf^2) - ((1/2) \times m \times vi^2)[/tex]
To find the net work (W) done on the particle by the external forces during the particle's motion in terms of the initial (Ki) and final (Kf) kinetic energies, we will use the work-energy theorem. The work-energy theorem states that the net work done on an object is equal to the change in its kinetic energy.
Step 1: Calculate the initial kinetic energy (Ki) and final kinetic energy (Kf).
Ki = (1/2) * m * vi²
Kf = (1/2) * m * vf²
Step 2: Calculate the change in kinetic energy (ΔK) as the difference between Kf and Ki.
ΔK = Kf - Ki
Step 3: According to the work-energy theorem, the net work (W) done on the particle by the external forces during its motion is equal to the change in kinetic energy (ΔK).
W = ΔK
Step 4: Substitute the expressions for Ki and Kf from step 1 into the equation for W from step 3.
W = ((1/2) * m * vf²) - ((1/2) * m * vi²)
In conclusion, the net work (W) done on the particle by the external forces during its motion can be expressed in terms of the initial (Ki) and final (Kf) kinetic energies as: W = ((1/2) * m * vf²) - ((1/2) * m * vi²)
To know more about work refer here:
https://brainly.com/question/31050706#
#SPJ11
Complete Question:
Find the net work W done on the particle by the external forces during the motion of the particle in terms of the initial and final kinetic energies. Express your answer in terms of Ki and Kf. Work done on the particle by the external forces during the particle's motion. To understand the meaning and possible applications of the work-energy theorem. In this problem, you will use your prior knowledge to derive one of the most important relationships in mechanics: the work-energy theorem. We will start with a special case: a particle of mass m moving in the x direction at constant acceleration a . During a certain interval of time, the particle accelerates from vi to vf, undergoing displacement is given by s=xf −xi.
a square loop 5 cm on each side carries a 500 ma current. the loop is within a uniform magnetic field of 1.2t. the axis of the loop, perpendicular to the plane of the loop, makes an angle of 30 degrees with the b field. what is the magnitude of the torque on the current loop?
The magnitude of the torque on the current loop is calculated using the formula τ=BIA sinθ, where B is the magnitude of the magnetic field, I is the current, A is the area of the loop, and θ is the angle between the magnetic field and the loop's plane. In this case, the magnitude of the torque is τ = (1.2 T)(0.5 A)(5 cm x 5 cm)sin(30°) = 7.5 x 10-3 Nm.
The torque is the rotational force that causes the loop to rotate. This is due to the fact that a force is exerted on the loop by the magnetic field when there is a current running through it. This force generates a torque on the loop, which will cause it to rotate until the angle between the plane of the loop and the magnetic field is 0°.
Know more about torque here
https://brainly.com/question/25708791#
#SPJ11
Types of self-esteem can be classified in many different ways. Fifteen year old Miguel
feels confident in himself because of his ability to make wise and ethical decisions. What
type of self-esteem would this be defined as?
social self-esteem
academic self-esteem
O physical self-esteem
moral self-esteem
Miguel's self-esteem, which is derived from his ability to make wise and ethical decisions, would be classified as moral self-esteem.
What is Self esteem?
Self-esteem refers to an individual's overall subjective evaluation of their own worth, value, and capabilities. It is the degree to which a person sees themselves as competent, worthy, and able to cope with life's challenges. Self-esteem can be influenced by a variety of factors, including genetics, upbringing, personal experiences, and social and cultural influences. People with high self-esteem tend to be more confident, resilient, and motivated, while those with low self-esteem may struggle with feelings of inadequacy, self-doubt, and insecurity.
The type of self-esteem described in the scenario is moral self-esteem. This is because Miguel feels confident in himself based on his ability to make wise and ethical decisions, which reflects his moral values and principles. Moral self-esteem is based on one's sense of right and wrong and the extent to which one adheres to their moral standards and values. It is an important aspect of overall self-esteem as it reflects an individual's integrity, character, and ethical conduct.
Learn more about Self esteem from given link
https://brainly.com/question/1447337
#SPJ1
what forces rick lieberman's plane to make an emergency landing? question 8 options: a. severe thunderstorms b. severe turbulence c. an ash cloud d. they ran out of coffee
The force that made Rick Lieberman's plane to make an emergency landing is b. severe turbulence.
Severe turbulence is sudden and violent turbulence that causes changes in altitude and altitude variations from the horizon. Turbulence is a natural phenomenon that can occur at any time, even when the skies are clear and blue.It can cause damage to the airplane and injure passengers, and it is a source of constant concern for pilots.
Severe turbulence is particularly dangerous because it can cause the plane to drop or gain altitude quickly, which can cause passengers to lose consciousness or be thrown from their seats. It is for this reason that planes are designed to withstand significant turbulence, and pilots receive extensive training on how to navigate through it. The correct option among the following given options is severe turbulence.
Learn more about turbulence at:
https://brainly.com/question/28102157
#SPJ11
calculate the average force on the person if he is stopped by a padded dashboard that compresses an average of 1.00 cm. calculate the average force on the person if he is stopped by an air bag that compresses an average of 15.0 cm.
The average force on the person if they are stopped by an airbag that compresses an average of 15.0 cm is approximately 70,000 N.
To calculate the average force on a person,
Average force = (change in momentum) / (time interval)
Assuming that the person's initial velocity is constant, we can simplify the formula to,
Average force = (mass of the person) x (change in velocity) / (time interval)
Now, let's consider the two scenarios,
Stopped by a padded dashboard that compresses an average of 1.00 cm:
Assuming the person's initial velocity is known and constant, we need to know the time interval it takes for the person to stop after hitting the dashboard. Without this information, we cannot calculate the average force.
Stopped by an airbag that compresses an average of 15.0 cm:
The time interval for an airbag to deploy and cushion the person's impact is typically very short (about 0.03 seconds), so we can assume that the time interval is negligible in this case. Therefore, we can use the simplified formula above.
Let's assume the mass of the person is 70 kg and their initial velocity is 30 m/s. The change in velocity is the final velocity (0 m/s) minus the initial velocity (30 m/s), which is -30 m/s. The negative sign indicates that the person's velocity is decreasing.
Using the formula,
Average force = (mass of the person) x (change in velocity) / (time interval)
= (70 kg) x (-30 m/s) / (0.03 s)
= -70,000 N
To know more about average force, here
brainly.com/question/29754124
#SPJ4
how much work is done by a person lifting a 6.7-kg object from the bottom of a well at a constant speed of 2.5 m/s for 9 s? write your answer in joules.
The amount of work done by a person lifting a 6.7-kg object from the bottom of a well at a constant speed of 2.5 m/s for 9 s is 1517.25 Joules.
The work done is determined using the equation below;
W = FdW = mgd
Where,W = Work done by the person,m = mass of object = 6.7 kg,g = acceleration due to gravity = 9.8 md = distance lifted by the person = ?We know that F = m(g + a) where a is the acceleration of the object that was lifted. The object is lifted at a constant velocity and so the acceleration of the object is zero. Hence,
F = mgF = 6.7 × 9.8F = 65.66 N
We can now determine the distance d that was lifted using the equation below;
d = vt
Where,v = constant velocity = 2.5 m/s.t = time taken = 9 s
Substituting the values; d = 2.5 × 9d = 22.5 m
Now we can determine the work done;
W = FdW = 65.66 × 22.5W = 1472.85 Joules (3 decimal places)
The work done by the person lifting a 6.7-kg object from the bottom of a well at a constant speed of 2.5 m/s for 9 s is 1517.25 Joules (2 decimal places)Answer: 1517.25 Joules.
More on work: https://brainly.com/question/29568084
#SPJ11
he maximum power rating of the electric motor is 145 watts. using the motor at this maximum rated power, how long will it take to accelerate a 2.00 kg car from 5.00 m/s to 11.6 m/s if we neglect all frictional losses?
It will take 0.7 seconds to accelerate the car from 5.00 m/s to 11.6 m/s, neglecting all frictional losses.
The power rating of an electric motor is measured in watts (W). A motor with a power rating of 145 W has the capacity to deliver 145 joules of energy per second.
The energy required to accelerate a 2.00 kg car from 5.00 m/s to 11.6 m/s can be calculated using the equation E = 0.5mv^2.
Here, m is the mass of the car (2.00 kg), and v is the difference in speed (11.6 m/s - 5.00 m/s).
This gives us E = 0.5 x 2.00 x (11.6 - 5.00)^2 = 74.48 J.
Since the motor can deliver 145 J of energy per second, it will take 0.5145/74.48 = 0.7 seconds to accelerate the car from 5.00 m/s to 11.6 m/s, neglecting all frictional losses.
For more such questions on Power Rating.
https://brainly.com/question/30265811#
#SPJ11