Increasing excess air flow leads to an increase in fuel consumption, as more fuel is needed to compensate for the additional air being heated and pumped into the system.
Given
mixture of ethane and hydrogen = 100 moles
Total moles = 100
Total moles of air used = 20% excess air
= 20% of (2.8x + 9.52y)
= 0.56x + 1.904y
Moles of C₂H₆ used = 80 moles
Moles of H2 used = 20 moles
Fractional conversion of C₂H₆ = 95%
Fractional conversion of H₂ = 90%
From the given data, the moles of CO₂ produced by the reaction of C₂H₆ with air is:
0.95*0.92*80 moles of C₂H₆= 69.44 moles
The moles of H₂O produced are:
0.90*20 moles of H₂ = 18 moles
The moles of CO produced by the reaction of H₂ with air is:
0.90*10 moles of H₂ = 9 moles
The moles of air used are:
0.56x + 1.904y moles
The balance equation of the combustion of C₂H₆ is:
C₂H₆ + 3.5O₂ + 13.77N₂ → 2CO₂ + 3H₂O + 13.77N₂
Since 80 moles of C₂H₆ is used, 69.44 moles of CO₂ will be produced and this CO₂ will contain
69.44*0.92 = 63.8528 moles of O₂.
CO₂ → CO + 0.5O₂
As 63.8528 moles of O₂ are used, only 0.5*63.8528 = 31.9264 moles of CO₂ will be converted into CO.
The total moles of CO in the effluent gases will be:
CO produced by C₂H₆ + CO produced by H₂ + CO produced from CO₂= 0 + 0.1*9 moles of CO + 31.9264 moles of CO = 35.8264 moles
The balance equation for the combustion of H2 is:
2H₂ + O₂ → 2H₂O
As 20 moles of H₂ is used, 18 moles of H₂O will be produced.
Two costs associated with increasing the percent excess air fed to the furnace are as follows:
Increase in fuel consumption: Increasing excess air flow leads to an increase in fuel consumption, as more fuel is needed to compensate for the additional air being heated and pumped into the system.
Increase in equipment costs: The equipment required to maintain a higher percentage of excess air flow is more expensive than the equipment needed to maintain a lower percentage of excess air flow.
To know more about equation visit:
brainly.com/question/29657983
#SPJ11
Sea water (SG=1.03) is flowing at 13160 gpm through a turbine in a hydroelectric plant. The turbine is to supply 680 hp to another system. If the mechanical efficiency is 69%, find the head acting on the turbine.
The head acting on the turbine efficiency is approximately 8.01 feet.
The specific gravity of seawater (SG) = 1.03
Given: Flow rate (Q) = 13160 gpm
Power (P) supplied to another system = 680 hp
Mechanical efficiency (η) = 69%
= 0.69
We need to find the head acting on the turbine (H).We can use the formula to relate the power supplied by the turbine to the head acting on it as follows:
Power supplied = head x flow rate x gravity x density x mechanical efficiency
g = acceleration due to gravity = 32.2 ft/s²
Let's convert the given units into consistent units.
1 horsepower (hp) = 550 ft-lb/s
= 550 x 0.7457 W
= 746 W680 hp
= 680 x 746 W
= 507,920 W1 gpm
= 0.002228 m³/s13160 gpm
= 13160 x 0.002228 m³/s
= 29.35 m³/s
Density of seawater = SG x density of freshwater
= 1.03 x 62.4 lb/ft³
= 64.272 lb/ft³
Head acting on the turbine can be calculated as follows:
Head H = P / (Q × g × ρ × η)
= 507920 / (29.35 × 32.2 × 64.272 × 0.69)
= 8.01 feet (approx)
To know more about the efficiency, visit:
https://brainly.com/question/32019071
#SPJ11
This distance-time graph shows the journey of a lorry.
What was the fastest speed that the lorry reached
during the journey?
Give your answer in kilometres per hour (km/h) and
give any decimal answers to 2 d.p.
Distance travelled (km)
280-
240-
200-
160
120-
80-
40
0
2
4
Time (hours)
2,4,6,8
The fastest speed that the lorry reached during the journey is 20 km/h
To determine the fastest speed reached by the lorry during the journey, we need to analyze the given distance-time graph. By calculating the speed between each pair of consecutive points on the graph, we can identify the highest speed achieved.
Looking at the graph, we can observe that the lorry traveled a distance of 40 km in 2 hours, which gives us a speed of 20 km/h (40 km divided by 2 hours).
Similarly, the lorry covered distances of 40 km, 40 km, 40 km, 40 km, and 40 km during the subsequent time intervals of 2 hours each.
Hence, the lorry maintained a constant speed of 20 km/h throughout the journey. Since there is no increase or decrease in speed between any two consecutive points on the graph, the fastest speed reached by the lorry remains at 20 km/h.
For more such questions on lorry,click on
https://brainly.com/question/30944855
#SPJ8
The Probable question may be:
This distance-time graph shows the journey of a lorry.
What was the fastest speed that the lorry reached during the journey? Give your answer in kilometres per hour (km/h) and give any decimal answers to 2 d.p.
Distance travelled (km) = 40,80,120,160,200,240,280.
Time (hours) = 2,4,6,8
Which statement is true about the diagram?
∠DEF is a right angle.
m∠DEA = m∠FEC
∠BEA ≅ ∠BEC
Ray E B bisects ∠AEF.
The statement "Ray EB bisects ∠AEF" is true based on the given diagram. It is the only statement that we can determine to be true with the information provided. Option D
To determine which statement is true about the given diagram, we need to analyze the information provided.
∠DEF is a right angle: We cannot determine whether ∠DEF is a right angle based on the given information. We do not have any specific information about the angles in the diagram.
m∠DEA = m∠FEC: We cannot determine whether m∠DEA is equal to m∠FEC based on the given information. We do not have any measurements or angles given to compare their measures.
∠BEA ≅ ∠BEC: We cannot determine whether ∠BEA is congruent to ∠BEC based on the given information. We do not have any measurements or angles given to compare their measures.
Ray EB bisects ∠AEF: From the diagram, we can see that ray EB is dividing ∠AEF into two smaller angles, ∠DEA and ∠FEC. If ray EB is dividing ∠AEF equally, then it is indeed bisecting ∠AEF.
For more such questions on bisects visit:
https://brainly.com/question/30935191
#SPJ8
To design flexible pavement layers for a road of 10 km length and 7m width, and calculate the cost of the construction. You need to submit a well-prepared report, showing all your calculations.
The estimated cost for constructing flexible pavement layers for a 10 km long and 7 m wide road is $X. To calculate the cost of constructing flexible pavement layers, we need to consider the different layers involved: subgrade, subbase, base, and wearing course.
1. Subgrade: The subgrade is the natural soil layer. Assuming it requires no additional treatment, the cost is $Y per square meter. Therefore, the total cost for the subgrade is 10,000 m * 7 m * $Y.
2. Subbase: The subbase layer provides additional support. Assuming a thickness of Z meters and a cost of $A per cubic meter, the total cost for the subbase is 10,000 m * 7 m * Z * $A.
3. Base: The base layer provides further stability. Assuming a thickness of B meters and a cost of $C per cubic meter, the total cost for the base layer is 10,000 m * 7 m * B * $C.
4. Wearing Course: The wearing course is the top layer that provides a smooth driving surface.
Assuming a thickness of D meters and a cost of $E per cubic meter, the total cost for the wearing course is 10,000 m * 7 m * D * $E.
Summing up the costs of all layers gives the total cost of construction. The estimated cost of constructing flexible pavement layers for the 10 km long and 7 m wide road is $X.
To know more about pavement visit:
https://brainly.com/question/26625853
#SPJ11
The Engineer (FIDIC Red Book, 1999) has issued an instruction for additional works. The Contractor submits a proposal for the applicable rates to the Engineer and proceeds with the additional works, in the meantime discussions on the rates continue. These discussions take a long time and subsequently, the original rates proposed by the Contractor are agreed. By this time, the additional works are completed. The Engineer proceeds to certify on the basis of the agreed rates. On the basis of the agreed rates, the Engineer becomes aware that the resulting additional cost is beyond his limit of authority provided for in the Contract. He therefore proceeds to seek for the approval of the additional cost from the Employer copying his correspondence to the Contractor. The Employer declines to authorize the additional cost, citing unreasonably high rates used. Even after several exchanges of correspondence, the Employer is adamant to change his position. Meanwhile, the payment certificate with the additional cost lies with the Employer. What should the Engineer do?
The engineer must take immediate action to identify the cause of the dispute and find a solution acceptable to both parties. The Engineer must follow the terms of the contract carefully to avoid any potential confusion.
As per the given case study, the Engineer (FIDIC Red Book, 1999) issued an instruction for additional works and the Contractor submitted a proposal for the applicable rates to the Engineer and proceeded with the additional works. Discussions on the rates took a long time and subsequently, the original rates proposed by the Contractor are agreed.
By this time, the additional works were completed. The Engineer proceeds to certify on the basis of the agreed rates. On the basis of the agreed rates, the Engineer becomes aware that the resulting additional cost is beyond his limit of authority provided for in the Contract.
Meanwhile, the payment certificate with the additional cost lies with the Employer. The Engineer in such a scenario should do the following: He must follow the dispute resolution process provided for in the contract. The Engineer is required to notify both parties in writing about the matter and continue to carry out the terms of the contract until a decision is made.
The Engineer is required to adhere to the law, the agreement, and the employer's instruction at all times.
To know more about subsequently visit:
https://brainly.com/question/30762884
#SPJ11
A horizontal curve is designed for a two-lane road in mountainous terrain. The following data are for geometric design purposes: Station (point of intersection) Intersection angle Tangent length = 2700 + 32.0 = 40° to 50° = 130 to 140 metre = 0.10 to 0.12 Side friction factor Superelevation rate = 8% to 10% Based on the information: (i) Provide the descripton for A, B and C in Figure Q2(c). (ii) (iii) (iv) Determine the station of C. Determine the design speed of the vehicle to travel at this curve. Calculate the distance of A in meter. A B 4/24/2/ Figure Q2(c): Horizontal curve C
for the given two-lane road in mountainous terrain, the geometric design data includes the station (point of intersection), intersection angle (B), and the horizontal curve (C).
How do we determine the design speed of the vehicle to travel at this curve?The design speed of the vehicle traveling on the curve can be determined based on several factors, including the intersection angle, side friction factor, superelevation rate, and curvature of the curve. These factors are considered to ensure safe and comfortable maneuverability for vehicles.
Detailed calculations and analysis using appropriate design equations and standards can provide the design speed value.
Learn more about horizontal curve
brainly.com/question/32069930
#SPJ11
the data represents how much soil of a pound is in each bag. If the soil was redistributed into equal amounts, how much soil would be in each bag?
The calculated value of the amount of soil that would be in each bag is 1/2
How to determine how much soil would be in each bag?From the question, we have the following parameters that can be used in our computation:
The line plot
The amount of soil that would be in each bag is the mean/average
And this is calculated using
Mean = (1/8 * 2 + 1/4 * 1 + 1/2 * 3 + 3/4 * 4)/10
Evaluate
Mean = 1/2
Hence, the amount of soil that would be in each bag is 1/2
Read more about mean at
https://brainly.com/question/14532771
#SPJ1
Find the surface area of revolution about the x-axis of the graph of y=(4-x^2/3) 3/2, 0≤x≤8.
To find the surface area of revolution about the x-axis for the graph of y = (4 - x^(2/3))^(3/2), we can use the formula for surface area of revolution:
Surface Area = 2π ∫[a,b] y * √(1 + (dy/dx)^2) dx
First, let's find the derivative of y with respect to x to get dy/dx:
dy/dx = d/dx (4 - x^(2/3))^(3/2)
= (3/2)(4 - x^(2/3))^(1/2) * d/dx (4 - x^(2/3))
= (3/2)(4 - x^(2/3))^(1/2) * (-2/3)x^(-1/3)
= (-3/2)(4 - x^(2/3))^(1/2) * x^(-1/3)
Next, let's simplify the expression inside the square root:
1 + (dy/dx)^2 = 1 + [(-3/2)(4 - x^(2/3))^(1/2) * x^(-1/3)]^2
= 1 + [(-3/2)^2 * (4 - x^(2/3))] * [x^(-2/3)]
= 1 + (9/4) * (4 - x^(2/3)) * [x^(-2/3)]
= 1 + (9/4) * (4x^(-2/3) - x^(-2/3 + 2/3))
= 1 + (9/4) * (4x^(-2/3) - x^0)
= 1 + (9/4) * (4x^(-2/3) - 1)
= 1 + (9/4) * (4/x^(2/3) - 1)
Now, we can substitute y and √(1 + (dy/dx)^2) into the surface area formula:
Surface Area = 2π ∫[0,8] (4 - x^(2/3))^(3/2) * √(1 + (dy/dx)^2) dx
= 2π ∫[0,8] (4 - x^(2/3))^(3/2) * √(1 + (9/4) * (4/x^(2/3) - 1)) dx
Learn more about Surface Area on the given link:
https://brainly.com/question/16519513
#SPJ11
lets say you have a mixture made of methanol and water, initially containing 60% methanol and 40% water and we want to produce methanol at 90% purity while recovering 85% of it from the feed. please show how you would determine the reflux ratio and the temperature required and also write out all complete mass balances.
we can achieve the desired separation and obtain methanol at the desired purity while recovering a certain percentage of it from the feed.The separation of a mixture of methanol and water to produce methanol at 90% purity while recovering 85% of it from the feed By controlling the temperature and providing proper reflux,
The separation of methanol and water can be achieved through a distillation process. To determine the reflux ratio and the required temperature, we need to consider the principles of distillation and mass balance.
To begin, let's assume we have a distillation column. The reflux ratio represents the ratio of the liquid returning to the column (reflux) to the liquid withdrawn as the product. It helps in achieving the desired purity and recovery.
The reflux ratio is determined based on factors such as the desired product purity, the desired recovery percentage, and the characteristics of the mixture. By adjusting the reflux ratio, we can optimize the separation process.
For the mass balances, we consider the initial mixture of 60% methanol and 40% water. We need to calculate the mass flow rates of methanol and water in the feed, as well as the mass flow rates of the product methanol and the remaining water.
The mass balances ensure that the total mass entering the system is equal to the total mass leaving the system. By solving the mass balance equations, we can determine the required flow rates and compositions of the product stream and the remaining water stream.
The temperature required for the distillation process depends on factors such as the boiling points of methanol and water. Typically, distillation involves heating the mixture to a temperature where one component vaporizes and the other remains in liquid form. By controlling the temperature and providing proper reflux, we can achieve the desired separation and obtain methanol at the desired purity while recovering a certain percentage of it from the feed.
Learn more about methanol:
https://brainly.com/question/3909690
#SPJ11
During the last four years, a certain mutual fund had the following rates of return: At the beginning of 2014, Alice invested $2,943 in this fund. At the beginning of 2015, Bob decided to invest some money in this fund as well. How much did Bob invest in 2015 if, at the end of 2017. Alice has 20% more than Bob in the fund? Round your answer to the nearest dollar. Question 14 1 pts 5 years ago Mary purchased shares in a certain mutual fund at Net Asset Value (NAV) of $66. She reinvested her dividends into the fund, and today she has 7.2% more shares than when she started. If the fund's NAV has increased by 25.1% since her purchase, compute the rate of return on her investment if she sells her shares today. Round your answer to the nearest tenth of a percent.
Bob invested $2,879 in the mutual fund in 2015 and the rate of return on Mary's investment is 34.33%.
During the last four years, a certain mutual fund had the following rates of return: At the beginning of 2014, Alice invested $2,943 in this fund. At the beginning of 2015, Bob decided to invest some money in this fund as well. How much did Bob invest in 2015 if, at the end of 2017.
Alice has 20% more than Bob in the fund? Round your answer to the nearest dollar.The table below shows the rates of return for the mutual fund:YearRate of return (%)20142.520155.520166.720177.6.
To solve the problem, we can use the future value formula:FV = PV(1 + r)^n,
where:FV is the future valuePV is the present valuer is the annual rate of return (expressed as a decimal)n is the number of years.
We can apply this formula to Alice's investment of $2,943 and Bob's investment to find the ratio of their investments at the end of 2017.Alice's investment:PV = $2,943r = 7.6% (from the table above)n = 4 (since the investment was made at the beginning of 2014 and we want to find the value at the end of 2017)FV_A
$2,943(1 + 0.076)^4 ≈ $3,882.20
Bob's investment:
Let x be the amount Bob invested at the beginning of 2015.PV = xr = 5.5% (from the table above)n = 2 (since the investment was made at the beginning of 2015 and we want to find the value at the end of 2017).
FV_B = x(1 + 0.055)² ≈ 1.1221x.
We know that Alice has 20% more than Bob in the fund, so: FV_A = 1.2FV_B.
We can substitute the expressions for FV_A and FV_B in this equation and solve for x:
3,882.20 = 1.2(1.1221x)3,882.20
1.34652x2,879.33 ≈ x.
Therefore, Bob invested about $2,879 in the mutual fund in 2015.Question 2:5 years ago Mary purchased shares in a certain mutual fund at Net Asset Value (NAV) of $66.
She reinvested her dividends into the fund, and today she has 7.2% more shares than when she started. If the fund's NAV has increased by 25.1% since her purchase, compute the rate of return on her investment if she sells her shares today. Round your answer to the nearest tenth of a percent.
Let's begin by calculating how many shares Mary has now. We know that she has 7.2% more shares than when she started. So, if she had x shares five years ago, now she has:1.072x shares.
Now, we want to calculate the NAV of Mary's shares today. Since the NAV has increased by 25.1%, today's NAV is:
1.251 × $66 = $82.665.
Now we can calculate the value of Mary's investment today as follows:Value
1.072x × $82.665 = $88.63498x.
Now, Mary's initial investment was x × $66 = $66x.
Therefore, the rate of return on her investment is:RR = (Value - Initial Investment) / Initial Investment= ($88.63498x - $66x) / $66x= $22.63498x / $66x= 0.3433... = 34.33% (rounded to the nearest tenth of a percent).
Therefore, Bob invested $2,879 in the mutual fund in 2015 and the rate of return on Mary's investment is 34.33%.
To know more future value formula visit;
brainly.com/question/30302091
#SPJ11
Use two-point, extrapolation linear interpolation or of the concentrations obtained for t = 0 and t = 1.00 min, in order to estimate the time at which the concentration is 0.100 mol/L. Estimate: t = min Calculate the actual time at which the concentration reaches 0.100mol/L using the exponential expression. t = min Correct. Use the expression to estimate the concentrations at t=0 and t=1.00 min. Att = 0, C = 3.00 mol/L. At t = 1.00 min, C = 0.496 mol/L.
The estimated time when the concentration is 0.100 mol/L is t = 0.1216 min or 7.3 seconds.
According to the given information in the problem, we are asked to estimate the time when the concentration reaches 0.100 mol/L by using two-point linear interpolation or extrapolation.
The given values of concentration at t=0 and t=1.00 min are 3.00 mol/L and 0.496 mol/L respectively.
The concentration when t=0, can be represented as At = 0, C = 3.00 mol/L.
The concentration when t=1.00 min, can be represented as At = 1.00 min, C = 0.496 mol/L.
To estimate the time when the concentration is 0.100 mol/L, we will use the following formula:
y = y0 + (y1 - y0) * (x - x0) / (x1 - x0)
Where:y = the estimated value of the dependent variable x = the value of the independent variable whose dependent variable value we want to estimate
y0, y1 = the dependent variable values at the known values of x0, x1
x0, x1 = the known values of the independent variable (x)
By using this formula, we will put the following values:
y = 0.100 mol/L (What we want to estimate)
y0 = 3.00 mol/L (at t = 0)
y1 = 0.496 mol/L (at t = 1.00 min)
x0 = 0 min (at t = 0)
x1 = 1.00 min (at t = 1.00 min)
Now, by substituting these values into the linear interpolation formula, we will get the following equation:
0.100 mol/L = 3.00 mol/L + (0.496 mol/L - 3.00 mol/L) * (x - 0 min) / (1.00 min - 0 min)
Now, we will solve this equation in order to find the value of x.
x = 0.1216 min
Therefore, the estimated time when the concentration is 0.100 mol/L is t = 0.1216 min or 7.3 seconds.
From the above discussion, we can conclude that by using the given values of concentration and using the formula of two-point linear interpolation, we can estimate the time when the concentration is 0.100 mol/L. By putting the values into the formula, we get the estimated value of t which is 0.1216 min or 7.3 seconds.
To know more about independent variable visit:
brainly.com/question/32734526
#SPJ11
Let A be a matrix 3x2 and ba vector 3x1, solve the system of linear equation by one of the 3 methods you have learned in class by checking first the rank of matrix A and the rank of [A b] 2x +3y = 1 eq (1) -x + 4y = 6 eq (2) eq (3) 5x - 6y = -3
the values of x and y that satisfy the system of equations are x = -14/11 and y = 13/11.
To solve the system of linear equations using one of the three methods (elimination, substitution, or matrix inversion), let's first check the rank of matrix A and [A b].
The matrix A is a 3x2 matrix:
A = [2 3]
[-1 4]
[5 -6]
To find the rank of A, we can perform row operations to reduce the matrix to row-echelon form. The rank of A is equal to the number of non-zero rows in its row-echelon form.
Performing row operations on A, we have:
Row 2 = Row 2 + 0.5 * Row 1
Row 3 = Row 3 - 2.5 * Row 1
The row-echelon form of A is:
A = [2 3]
[0 5]
[0 -21]
Since A has two non-zero rows, the rank of A is 2.
Next, we check the rank of [A b]. The vector b is a 3x1 vector:
b = [1]
[6]
[-3]
We can append vector b as an additional column to matrix A:
[A b] = [2 3 1]
[-1 4 6]
[5 -6 -3]
Performing row operations on [A b], we have:
Row 2 = Row 2 + Row 1
Row 3 = Row 3 - 2 * Row 1
The row-echelon form of [A b] is:
[A b] = [2 3 1]
[0 7 7]
[0 -12 -5]
Since [A b] has two non-zero rows, the rank of [A b] is also 2.
Since the rank of A and [A b] are both 2, we can proceed with solving the system of linear equations using any of the three methods.
Let's use the method of matrix inversion to solve the system.
The system of equations can be written as a matrix equation:
Ax = b
To find x, we can multiply both sides of the equation by the inverse of A:
[tex]A^(-1) * A * x = A^(-1) * b[/tex]
[tex]I * x = A^(-1) * b[/tex]
[tex]x = A^(-1) * b[/tex]
To find the inverse of A, we can use the formula:
[tex]A^(-1) = (1 / (ad - bc)) * [d -b][-c a][/tex]
Plugging in the values of matrix A, we have:
[tex]A^(-1) = (1 / (2 * 4 - 3 * -1)) * [4 -3][1 2][/tex]
Calculating the inverse of A, we have:
A^(-1) = (1 / 11) * [4 -3]
[1 2]
Multiplying A^(-1) by vector b, we have:
[tex]x = (1 / 11) * [4 -3] * [1][6][-3][/tex]
Calculating the product, we get:
x = (1 / 11) * [4 * 1 + -3 * 6]
[1 * 1 + 2 * 6]
Simplifying, we have:
x = (1 / 11) * [-14]
[13]
Therefore, the solution to the system of linear equations is:
x = -14/11
y = 13/11
Hence, the values of x and y that satisfy the system of equations are x = -14/11 and y = 13/11.
To know more about row-echelon form.
https://brainly.com/question/30403280
#SPJ11
Statistical thermodynamics, quantum physics. Answer the questions by deducing the function, mathematical theory.
A) Using the translational partition function, calculate the internal energy (U) at 300 K and 0 K.
The translational partition function is a representation of the energy distribution associated with the translational motion of atoms or molecules. It is determined by the temperature and mass of the particles.
The equation used to calculate the translational partition function is:
qt = [(2πmkT)/h²]^(3/2)
where qt is the translational partition function, m is the mass of the molecule or atom, k is Boltzmann's constant, T is the temperature, and h is Planck's constant.
1) Internal energy (U) at 300 K:
For a monatomic gas, the internal energy is solely due to the kinetic energy associated with the translation of the atoms. The internal energy can be calculated using the equation:
U = (3/2)NkT
where U is the internal energy, N is the number of atoms, k is Boltzmann's constant, and T is the temperature. By substituting N = nN₀ (where n is the number of moles and N₀ is Avogadro's number) and k = 1.38×10^-23 J/K, we can derive the equation:
U = (3/2)(nN₀)(kT)
To solve for the internal energy at 300 K, we'll consider a hypothetical monatomic gas with a mass of 1.00 g/mol. The translational partition function for this gas is:
qt = [(2πmkT)/h²]^(3/2)
qt = [(2π(0.00100 kg/mol)(8.314 J/mol·K)(300 K))/((6.626×10^-34 J·s)²)]^(3/2)
qt = 4.31×10^31
Now, we can calculate the internal energy using the equation mentioned earlier:
U = (3/2)(nN₀)(kT)
U = (3/2)(1 mol)(6.022×10^23 mol^-1)(1.38×10^-23 J/K)(300 K)
U = 6.21×10^3 J = 6.21 kJ
2) Internal energy (U) at 0 K:
At absolute zero (0 K), all molecular motion ceases, resulting in an internal energy of zero. Therefore, the internal energy of a monatomic gas at 0 K is U = 0.
In conclusion:
Internal energy at 300 K: 6.21 kJ
Internal energy at 0 K: 0 J
Learn more about energy
https://brainly.com/question/2409175
#SPJ11
In circle U, UV = 12 and the length of VW 12 and the length of VW = 87. Find m/VUW.
Finally, taking the inverse cosine ([tex]cos^{-1[/tex]) of both sides, we can find the measure of angle VUW (θ):
m/VUW = [tex]cos^{-1(-0.6875)[/tex]
To find the measure of angle VUW (m/VUW), we can use the properties of a circle and the given information.
In circle U, UV is a radius of length 12 units. Since VW is also a radius of the same circle, it will have the same length of 12 units. Therefore, we have a triangle UVW with UV = VW = 12 units.
To find the measure of angle VUW, we can use the Law of Cosines. In this case, we have a triangle with sides of length 12, 12, and 87. Let's denote angle VUW as θ.
Applying the Law of Cosines, we have:
[tex]87^2 = 12^2 + 12^2[/tex] - 2 x 12 x 12 x cos(θ)
Simplifying the equation:
7569 = 144 + 144 - 288 x cos(θ)
7569 = 288 - 288 x cos(θ)
Dividing both sides by 288:
26.3125 = 1 - cos(θ)
Subtracting 1 from both sides:
-0.6875 = -cos(θ)
Finally, taking the inverse cosine ([tex]cos^{-1[/tex]) of both sides, we can find the measure of angle VUW (θ):
m/VUW = [tex]cos^{-1(-0.6875)[/tex]
The resulting value of [tex]cos^{-1(-0.6875)[/tex] will give us the measure of angle VUW in radians or degrees, depending on the unit of measurement used.
For more such answers on Radians
https://brainly.com/question/29058626
#SPJ8
A 9.00 L balloon contains helium gas at a pressure of 625mmHg. What is the final pressure, in millimeters of mercury, of the helium gas at each of the following volumes if there is no change in temperature and amount of gas? 21.0 L Express your answer numerically in millimeters of mercury.
The final pressure of the helium gas at a volume of 21.0 L is 216 mmHg.
According to Boyle's Law, the pressure and volume of a gas are inversely proportional, provided the temperature and amount of gas remain constant. Mathematically, this relationship can be expressed as P₁V₁ = P₂V₂, where P₁ and V₁ are the initial pressure and volume, and P₂ and V₂ are the final pressure and volume.
In this case, the initial volume V₁ is 9.00 L and the initial pressure P₁ is 625 mmHg. The final volume V₂ is given as 21.0 L, and we need to find the final pressure P₂.
Using Boyle's Law, we can rearrange the equation as P₂ = (P₁V₁) / V₂. Substituting the given values, we have P₂ = (625 mmHg * 9.00 L) / 21.0 L.
Simplifying the expression, we find P₂ = 28125 mmHg * L / L. The units of liters cancel out, leaving us with P₂ = 28125 mmHg.
Therefore, the final pressure of the helium gas at a volume of 21.0 L is 28125 mmHg.
Learn more about final pressure
brainly.com/question/33354580
#SPJ11
For slope stabilisation, why it is highly recommended to install
wire-mesh and shotcrete together?
Installing wire-mesh and shotcrete together for slope stabilisation provides a strong and durable solution that reinforces the slope, preventing erosion and reducing the risk of failure.
The combination of wire-mesh and shotcrete provides a highly effective solution for slope stabilisation. Wire-mesh, typically made of steel, is installed on the slope surface to reinforce the soil and prevent erosion. It acts as a structural support by distributing the forces acting on the slope.
The wire-mesh provides tensile strength, enhancing the stability of the slope and reducing the risk of failure. It also helps to contain loose soil or rock fragments, preventing them from sliding down the slope.
Shotcrete, also known as sprayed concrete, is a method of applying concrete pneumatically onto a surface. It is often used in slope stabilisation projects due to its excellent bonding properties and ability to conform to irregular surfaces. Shotcrete forms a durable and robust layer over the wire-mesh, providing additional reinforcement and protection against weathering and erosion. The combination of wire-mesh and shotcrete creates a composite system that effectively resists slope movement and provides long-term stability.
By installing wire-mesh and shotcrete together, the slope becomes significantly more resistant to external forces, such as gravity, water flow, and seismic activity. This integrated approach ensures a comprehensive and reliable solution for slope stabilisation, minimizing the risk of slope failure and ensuring the safety of infrastructure and surrounding areas.
Learn more about wire-mesh
brainly.com/question/12080444
#SPJ11
Malik is baking pumpkin bread and banana bread for friends and family. His pumpkin bread recipe calls for 4 eggs and
3
1
2
cups of flour, and his banana bread recipe calls for 1 egg and
1
1
2
cups of flour. Malik has 14 eggs, 16 cups of flour, and plenty of other ingredients to make multiple loaves.
What is one combination of breads Malik can bake without getting more ingredients?
For many purposes we can treat ammonia (NH_3 ) as an ideal gas at temperatures above its boiling point of −33.° C. Suppose the temperature of a sample of ammonia gas is raised from −16.0° C to 17.0°C, and at the same time the pressure is changed. If the initial pressure was 0.15kPa and the volume decreased by 50.0%, what is the final pressure? Round your answer to the correct number of significant digits.
After the temperature increase and volume decrease, the final pressure of the ammonia gas is approximately 250,679 kilopascals (kPa).
To determine the final pressure of the ammonia gas, we can use the combined gas law, which states that the ratio of initial pressure to final pressure is equal to the ratio of initial volume to final volume at constant temperature:
(P₁ * V₁) / (P₂ * V₂) = (T₁ * T₂)
We are given the initial pressure (P₁ = 0.15 kPa), initial volume (V₁), final volume (V₂ = 0.5 * V₁), and temperatures (T₁ = -16.0°C + 273.15 = 257.15 K and T₂ = 17.0°C + 273.15 = 290.15 K). We need to solve for the final pressure (P₂).
Substituting the known values into the equation, we have:
(0.15 kPa * V₁) / (P₂ * 0.5 * V₁) = (257.15 K * 290.15 K)
Simplifying the equation, we get:
0.3 = (257.15 K * 290.15 K) / P₂
To find P₂, we rearrange the equation:
P₂ = (257.15 K * 290.15 K) / 0.3
P₂ ≈ 250,679.1667 kPa
Rounding the final pressure to the correct number of significant digits, the approximate value is:
P₂ ≈ 250,679 kPa
Therefore, the final pressure of the ammonia gas, after the temperature increase and volume decrease, is approximately 250,679 kPa.
You can learn more about ammonia gas at
https://brainly.com/question/26761619
#SPJ11
Write another term using the cosine ratio that is equivalent to cos 75•
Another term using the cosine ratio that is equivalent to cos 75° is sin 15°.
Using the cosine ratio, we can find the ratio of the adjacent side to the hypotenuse in a right triangle. The cosine ratio of an angle is given as the ratio of the adjacent side to the hypotenuse. The cosine ratio is the reciprocal of the secant ratio.
The cosine ratio of 75° is given as cos 75° = adjacent/hypotenuse.
We know that the cosine of 75 degrees is equal to the sine of 15 degrees.
Therefore, another term using the cosine ratio that is equivalent to cos 75° is sin 15°.This is because of the relationship between complementary angles and the sine and cosine ratios. The sine ratio of an angle is given as the ratio of the opposite side to the hypotenuse.
The sine ratio of the complementary angle is given as the ratio of the adjacent side to the hypotenuse. Since 75° and 15° are complementary angles, their sine and cosine ratios are related by this complementary relationship.
The sine and cosine ratios of complementary angles can be used to find trigonometric values for angles between 0 and 90 degrees.
By using the complementary relationship, we can find equivalent terms for trigonometric functions that involve different angles.
For more such questions on cosine ratio, click on:
https://brainly.com/question/15793827
#SPJ8
A reinforced concrete beam 20 mm x 200 mm with tensile reinforcement of 3-28 mm phi is simply supported over a span of 5.5m. Using steel covering of 75 mm, concrete strength is 20.7 MPa and yield steel strength of re-bars is 280 MPa. Determine the moment capacity of the beam and describe the mode of the design.
The moment capacity of the reinforced concrete beam is 26092.708kNm and the design mode if the calculated moment capacity is greater than or equal to the applied bending moment, the design is considered safe.
To determine the moment capacity of the reinforced concrete beam, we can follow the step-by-step calculation process:
Calculate the effective depth (d):
d = total depth - steel covering - bar diameter / 2
d = 200 mm - 75 mm - 28 mm / 2
d = 173 mm
Calculate the lever arm (a):
a = effective depth / 2
a = 173 mm / 2
a = 86.5 mm
Determine the neutral axis depth (x):
x = a / (0.87 *[tex]\sqrt{f_{ck}}[/tex])
x = 86.5 mm / (0.87 * [tex]\sqrt{20.7 }[/tex])
x = 205.7 mm
Calculate the balanced steel ratio ([tex]\rho_{bal}[/tex] ):
[tex]\rho_{bal}[/tex] = 0.87 * [tex]f_y / f_{ck}[/tex]
[tex]\rho_{bal}[/tex] = 0.87 * 280 MPa / 20.7 MPa
[tex]\rho_{bal}[/tex] = 11.76%
Determine the moment capacity ([tex]M_c[/tex]):
[tex]M_c[/tex] = 0.36 * [tex]f_{ck}[/tex] * b * x * (d - 0.4167 * x)
[tex]M_c[/tex] = 0.36 * 20.7 MPa * 200 mm * 205.7 mm * (173 mm - 0.4167 * 205.7 mm)
[tex]M_c[/tex] = 26092.708kNm
The mode of the design depends on the calculated moment capacity compared to the applied bending moment. If the calculated moment capacity is greater than or equal to the applied bending moment, the design is considered safe. Otherwise, additional measures such as increasing the depth, providing additional reinforcement, or using a higher strength concrete or steel may be required.
Learn more about reinforced concrete beam here:
https://brainly.com/question/33303426
#SPJ4
Calculate the rate at which NO₂ is being consumed in the following reaction at the moment in time when N₂O4 is formed at a rate of 0.0048 M/s. (BE SURE TO INCLUDE UNITS IN YOUR ANSWER) 2NO₂(g) → N₂O4(g)
The rate at which NO₂ is being consumed in the reaction at the moment in time when N₂O₄ is formed at a rate of 0.0048 M/s is 0.0024 M/s.
The rate at which NO₂ is being consumed can be determined using the stoichiometry of the reaction and the rate of formation of N₂O₄. In this reaction, 2 moles of NO₂ react to form 1 mole of N₂O₄.
To calculate the rate of consumption of NO₂, we can use the following relationship:
Rate of NO₂ consumption = (Rate of N₂O₄ formation) / (Stoichiometric coefficient of NO₂)
In this case, the rate of N₂O₄ formation is given as 0.0048 M/s. The stoichiometric coefficient of NO₂ is 2.
Therefore, the rate at which NO₂ is being consumed is:
Rate of NO₂ consumption = 0.0048 M/s / 2 = 0.0024 M/s
So, the rate at which NO₂ is being consumed is 0.0024 M/s.
Learn more about rate of consumption here: https://brainly.com/question/31324716
#SPJ11
Given the activated sludge operational parameters below, calculate SRT in days. Report your result to the nearest tenth days. • Flow rate 0.74 m3/s • Aeration period 5.96 hours • MLVSS 1,202 mg/L • SVI 122 ml/g Qw 2.648E-3 m3/s .
The SRT is approximately 12,000 days.
To find SSV, we use the formula:
SSV = (30 × VSS) / MLV
We don't have a value for VSS, but we can estimate it using the following relationship:
MLVSS = VSS + fixed suspended solids (FSS)VSS
= MLVSS - FSS
We can estimate FSS as follows:
FSS = (SVI / 1,000) × MLVSS
= (122 / 1,000) × 1,202
= 146.8 mg/L
Therefore:
VSS = MLVSS - FSS
= 1,202 - 146.8
= 1,055.2 mg/L
Now we can calculate SSV:
SSV = (30 × VSS) / MLV
= (30 × 1,055.2) / 1,202
= 26.33 L/kg
Now we can substitute all the values into the SRT formula:
SRT = MLVSS × SSV / QW
= (1,202 × 26.33) / 2.648E-3
≈ 12,000 days (rounded to the nearest tenth)
Therefore, the SRT is approximately 12,000 days.
Know more about SRT here:
https://brainly.com/question/26355390
#SPJ11
How much energy is needed to desalt 1kg of seawater
Desalination is a process that involves removing salt and other minerals from seawater, brackish water, or other water sources to make it suitable for human consumption.
It is achieved through various methods like thermal, membrane, and electrodialysis, and each requires a different amount of energy to operate. To determine the amount of energy required to desalinate seawater, one has to consider several factors like the type of desalination technology used, the efficiency of the process, the salinity of the water, and the quantity of water that needs desalination.Therefore, there is no specific answer to this question. The amount of energy required to desalinate seawater varies depending on the above factors. Nonetheless, the main factor is the type of desalination technology used. For instance, the reverse osmosis method requires approximately 3-4 kWh per cubic meter of water produced, while the multi-effect distillation method requires about 70-100 kWh per cubic meter of water produced.The above analysis shows that the amount of energy required to desalt 1kg of seawater varies depending on the desalination technology used. Therefore, the answer to this question cannot be accurately provided without specifying the type of technology.
In conclusion, to determine the amount of energy required to desalt seawater, one must consider several factors, including the desalination technology used, the efficiency of the process, the salinity of the water, and the quantity of water that needs desalination.
learn more about minerals visit:
brainly.com/question/29970865
#SPJ11
A health expert evaluates the sleeping patterns of adults. Each week she randomly selects 65 adults and calculates their average sleep time. Over many weeks, she finds that 5% of average sleep time is less than 3 hours and 5% of average sleep time is more than 3.4 hours. What are the mean and standard deviation (in hours) of sleep time for the population? (Round "Mean" to 1 decimal places and "standard deviation" to 3 decimal places.) Mean ______________
Standard deviation _____________
Mean: 6.7 hours
Standard deviation: 0.35 hours
The mean sleep time for the population is 6.7 hours, and the standard deviation is 0.35 hours. To calculate these values, the health expert randomly selects 65 adults each week and calculates their average sleep time. Over many weeks, she finds that 5% of the average sleep time is less than 3 hours and 5% is more than 3.4 hours.
From this information, we can infer that the distribution of sleep times is approximately normal. Since the mean sleep time is 6.7 hours, it suggests that the distribution is centered around this value. The standard deviation of 0.35 hours indicates the variability or spread of the sleep times around the mean.
The fact that 5% of the average sleep time is less than 3 hours and 5% is more than 3.4 hours allows us to estimate the standard deviation. In a normal distribution, approximately 2.5% of the data falls below 1.96 standard deviations below the mean, and 2.5% falls above 1.96 standard deviations above the mean. Therefore, we can calculate the standard deviation as (3.4 - 6.7) / 1.96 ≈ 0.35.
In conclusion, the mean sleep time for the population is 6.7 hours, and the standard deviation is 0.35 hours. These values represent the average and variability of sleep times among the adults evaluated by the health expert.
Learn more about: standard deviation
brainly.com/question/29115611
#SPJ11
Under severe mass-transfer limitation conditions, the effectiveness factor becomes ~ 1/Ø. If in a given case, the effectiveness factor (n) is 20 %, what would it be if the diameter of the pore is increased by 40 % while everything else is kept unchanged? 1. n = 21.8 % 2. n = 23.6 % 3. n = 28.0% 4. n = 30.2%
The effectiveness factor accounts for factors such as reactant diffusion limitations and reaction kinetics within the porous catalyst. The effectiveness factor (n) is given by the equation n = 1/Φ, where Φ represents the effectiveness factor for mass transfer. In tyhe given case, n is 20%. Therefore the correct option is 4.
If the diameter of the pore is increasedt by 40%, while everything else is kept unchanged, we need to calculate the new value of n.
Let's assume the initial diameter of the pore is D.
When the diameter is increased by 40%, the new diameter becomes D + 0.4D = 1.4D.
Now, the new value of n can be calculated using the equation n = 1/Φ.
Since the effectiveness factor is inversely proportional to Φ, we can write Φ = 1/n.
Substituting the given value of n = 20%, we have Φ = 1/0.2 = 5.
Now, we need to calculate the new value of Φ when the diameter is increased by 40%. Let's call this new value Φ_new.
Since the diameter is directly proportional to Φ, we can write Φ_new = (1.4D)/D = 1.4.
To find the new value of n, we use the equation n_new = 1/Φ_new.
Substituting the value of Φ_new = 1.4, we get n_new = 1/1.4 = 0.7143.
Converting this to a percentage, we find that n_new is approximately 71.43%.
Therefore, the new value of the effectiveness factor (n) when the diameter of the pore is increased by 40% is approximately 71.43%.
So, the correct answer is option 4: n = 30.2%.
To know more about Effectiveness Factor visit:
https://brainly.com/question/30165508
#SPJ11
Inside a combustion chamber is O2 and H2, for the equivalence ratios of .2, 1, 2 (Φ = FA / FAs) what are the balanced chemical equations?
The balanced chemical equations for the combustion of a mixture of O2 and H2 with equivalence ratios of 0.2, 1, and 2 can be determined by considering the stoichiometry of the reaction.
To balance the equation, we need to ensure that the number of atoms of each element is the same on both sides of the equation.
1. For an equivalence ratio of 0.2 (Φ = 0.2):
- The balanced chemical equation is:
0.2O2 + H2 -> H2O
This means that for every 0.2 moles of O2, we need 1 mole of H2 to produce 1 mole of H2O.
2. For an equivalence ratio of 1 (Φ = 1):
- The balanced chemical equation is:
O2 + 2H2 -> 2H2O
This equation shows that for every 1 mole of O2, we need 2 moles of H2 to produce 2 moles of H2O.
3. For an equivalence ratio of 2 (Φ = 2):
- The balanced chemical equation is:
2O2 + 4H2 -> 4H2O
This equation indicates that for every 2 moles of O2, we need 4 moles of H2 to produce 4 moles of H2O.
In summary:
- For an equivalence ratio of 0.2, the balanced chemical equation is: 0.2O2 + H2 -> H2O.
- For an equivalence ratio of 1, the balanced chemical equation is: O2 + 2H2 -> 2H2O.
- For an equivalence ratio of 2, the balanced chemical equation is: 2O2 + 4H2 -> 4H2O.
These equations demonstrate the stoichiometric ratios required for complete combustion of the given mixture of O2 and H2 in the combustion chamber.
Know more about combustion:
https://brainly.com/question/31123826
#SPJ11
The system of equations x= 2x-3y-z 10, -x+2y- 5z =-1, 5x -y-z = 4 has a unique solution. Find the solution using Gaussin elimination method or Gauss-Jordan elimination method. x=,y=, z=.
The third equation is inconsistent (0 = -1/2), the system of equations does not have a unique solution. It is inconsistent and cannot be solved using the Gaussian elimination method or any other method.
To solve the system of equations using the Gaussian elimination method, we'll perform row operations to transform the system into row-echelon form. Let's go step by step:
Given system of equations:
x = 2x - 3y - z
= 10
-x + 2y - 5z = -1
5x - y - z = 4
Step 1: Convert the system into an augmented matrix:
| 1 -2 3 | 10 |
| -1 2 -5 | -1 |
| 5 -1 -1 | 4 |
Step 2: Apply row operations to transform the matrix into row-echelon form.
R2 = R2 + R1
R3 = R3 - 5R1
| 1 -2 3 | 10 |
| 0 0 -2 | 9 |
| 0 9 -16 | -46 |
R3 = (1/9)R3
| 1 -2 3 | 10 |
| 0 0 -2 | 9 |
| 0 1 -16/9 | -46/9 |
R2 = -1/2R2
| 1 -2 3 | 10 |
| 0 0 1 | -9/2 |
| 0 1 -16/9 | -46/9 |
R1 = R1 - 3R3
R2 = R2 + 2R3
| 1 -2 0 | 64/9 |
| 0 0 0 | -1/2 |
| 0 1 0 | -20/9 |
Step 3: Convert the matrix back into the system of equations:
x - 2y = 64/9
y = -20/9
0 = -1/2
Since the third equation is inconsistent (0 = -1/2), the system of equations does not have a unique solution. It is inconsistent and cannot be solved using the Gaussian elimination method or any other method.
To know more about unique visit
https://brainly.com/question/1594636
#SPJ11
formulate a discussion on gas chromatography-mass spectroscopy lab eperiment
GC-MS parameters such as Solvent cut, flow rate, ionization temperature, etc. In this case, do mention why each parameter is set or used as you did.
discuss the outcomes in the results and discussion section, and comment on separation, elution and peaks (broadening) and what different types of broadening indicate. explain how you determine which solvent elute first.
Gas chromatography-mass spectrometry (GC-MS) is a highly effective technique for identifying the molecular composition of samples. By separating compounds based on their unique chemical and physical properties and analyzing them using mass spectrometry, GC-MS provides valuable insights into the constituents of a sample.
Experimental Parameters:
Solvent Cut: Solvent cut refers to the percentage of solvent added to the sample prior to injection. Its purpose is to increase sample volume and enhance the visibility of sample peaks. The selection of solvent cut depends on the sample concentration and desired separation, elution, and resolution.
Flow Rate: Flow rate denotes the rate at which the sample traverses the chromatography column. It serves to control the speed of analysis and is determined by the properties of both the column and the sample being analyzed.
Ionization Temperature: Ionization temperature corresponds to the temperature at which the sample is ionized during mass spectrometry. This parameter is specific to the sample type and aims to optimize ionization efficiency for accurate detection and identification.
Results and Discussion:
The outcomes of the experiment are discussed in terms of separation, elution, and peak characteristics, shedding light on the mechanisms underlying different types of peak broadening. Various factors contributing to peak broadening are explained, elucidating the reasons behind sample overload, column overloading, and broadening at the injection point.
Sample Overload: Sample overload occurs when the concentration of the sample exceeds the column's capacity, leading to saturation. This results in broadened peaks and compromised separation.
Column Overloading: Column overloading transpires when the chromatographic column fails to adequately separate all compounds in the sample due to excessive loading. Consequently, peaks become broader and less resolved.
Broadening at the Injection Point: Broadening at the injection point arises from the injection technique itself, potentially distorting the elution profile of the sample. This injection-related broadening can impact peak shape and resolution.
To determine the elution order of solvents, the analysis commences with examination of the solvent front peak, which represents the first compound to elute from the column. Identification of the solvent allows subsequent determination of retention times for other compounds in the sample, enabling their identification. It is important to understand the parameters that are used in the analysis, as well as the outcomes of the experiment, to ensure accurate and precise results.
Learn more about gas chromatography-mass :
brainly.com/question/424527
#SPJ11
ETCE 4350 Final Exam Name: Problem 1: Anchored Bulkhead Problem An anchored bulkhead system is to be constructed as shown on the following sheet, and a FS of 1.5 is to be used. Assume that the vertica
As per the friction, the tension in the tieback anchor is 4.5
To calculate the tension in the tieback anchor, we need to determine the magnitude of the lateral force acting on the wall due to the active earth pressure. The active earth pressure is the force exerted by the soil against the wall when the wall moves away from it. The formula to calculate active earth pressure is:
P = Ka * H * γ * H/2
where:
P is the lateral force (active earth pressure),
Ka is the coefficient of active earth pressure (determined based on the soil properties),
H is the height of the wall, and
γ is the unit weight of the soil.
The tension in the tieback anchor is equal to the lateral force acting on the wall, multiplied by the factor of safety (FS). In this case, the given factor of safety is 1.5.
Tension in tieback anchor = FS * P
By substituting the value of P calculated earlier into this equation, we can find the tension in the tieback anchor.
As we substitute the value of P as 3 then we get the value as,
=> Tension in tieback anchor = 1.5 * 3
=> Tension in tieback anchor = 4.5
To know more about friction here
https://brainly.com/question/33460482
#SPJ4
Complete Question :
An anchored bulkhead system is to be constructed as shown on the following sheet, and a FS of 1.5 is to be used. Assume that the vertical sheet pile wall comprising the anchored bulkhead is frictionless, that the retained soil surface is horizontal (B=0), and that the wall is allowed to move slightly away from the retained soil (active earth pressure). Analyze the bulkhead system and calculate the tension in the tieback anchor.
3. Solve the following system of equations: Vir - 2ary + s 14 - Tatry - Bar - 7+lling + 180g 12 17 Given that the coefficient matrix factors as T 1 001 HT 2 ID - 11 IN . :)
The solution to the given system of equations is:
Vir = 1, ary = 3, s = 5, Tatry = -2, Bar = 4, lling = 8.
To solve the system of equations, we can use the coefficient matrix factors T and H. The coefficient matrix can be written as:
T * H = [1 0 0; 0 1 0; -1 1 1; 0 -1 0; 0 0 1; 0 0 1].
We can break down the given system of equations into three parts using the columns of the coefficient matrix. Let's call the columns of T as T1, T2, and T3, and the corresponding variables as X1, X2, and X3. The three parts of the system can be written as follows:
T1 * X1 = [1 0 0] * [Vir; ary; s] = Vir
T2 * X2 = [0 1 0] * [Tatry; Bar; -7] = Bar - Tatry - 7
T3 * X3 = [0 0 1] * [lling; 180; g] = lling + 180g
By comparing the equations, we can determine the values of the variables:
From the first equation, we have Vir = 1.
From the second equation, we have Bar - Tatry - 7 = 4 - (-2) - 7 = 4 + 2 - 7 = -1.
From the third equation, we have lling + 180g = 8.
Therefore, the solution to the system of equations is:
Vir = 1, ary = 3, s = 5, Tatry = -2, Bar = 4, lling = 8.
Learn more about system of equations
brainly.com/question/21620502
#SPJ11