Answer:
A generator is a device that converts mechanical energy into electrical energy by rotating a coil of wire in a magnetic field.
A small and a large block (mass M and 2M respectively) are arranged on a horizontal surface as shown below. A student pushes on the left side of the small block so that the entire system accelerates to the right. How does the net force on the small block Fs compare to the net force on the large block F₁? Fs=FL Fs < FL 0/2 pts Fs > FL
The net force on the small block (Fs) is equal to the net force on the large block (F₁).
According to Newton's third law of motion, for every action, there is an equal and opposite reaction. When the student pushes on the left side of the small block, an equal and opposite force is exerted by the small block on the student's hand. This force is transmitted through the small block to the large block due to their contact.
Since the small and large blocks are in contact, they experience the same magnitude of force but in opposite directions. Therefore, the net force on the small block is equal in magnitude and opposite in direction to the net force on the large block.
In a system where both blocks are accelerating to the right, there must be an unbalanced force acting on the system. This unbalanced force is provided by the student's push and is transmitted through both blocks. As the large block has a greater mass, it requires a larger force to accelerate it compared to the smaller block. However, the net force acting on each block, Fs and F₁, will be equal in magnitude, satisfying Newton's third law.
Learn more about Newton's third law of motion:
https://brainly.com/question/29768600
#SPJ11
Newton's 2nd law of motion is only valid in inertial frame of reference. (i) Define what is meant by inertial frame of reference. (5 marks) (ii) Consider a reference frame that rotates at uniform angular velocity, but moves in constant motion with respect to a inertial frame. Write down the equation of motion of a particle mass m that moves with velocity with respect to rotating frame. Explain all the force terms involved in the Newton's law of motion for this case. (15 marks) 5/8 SIF2004 (iii) Consider a bucket of water set to spin about its symmetry axis at uniform w. the most form of effective as determined in (i), show that at equilibrium, the surface of the water in the bucket takes the shape of a parabola. State all assumptions and to approximations.
(i) An inertial frame of reference is a non-accelerating frame where Newton's laws of motion hold true.
(ii) In a rotating frame, the equation of motion includes the inertial force, Coriolis force, and centrifugal force, affecting the motion of a particle.
(i) Inertial Frame of Reference:
An inertial frame of reference is a frame in which Newton's laws of motion hold true, and an object at rest or moving in a straight line with constant velocity experiences no net force. In other words, an inertial frame of reference is a non-accelerating frame or a frame moving with a constant velocity.
(ii) Equation of Motion in a Rotating Frame:
In a reference frame that rotates at a uniform angular velocity but moves with constant velocity with respect to an inertial frame, the equation of motion for a particle of mass m moving with velocity [tex]\(\mathbf{v}\)[/tex]with respect to the rotating frame can be written as:
[tex]\[ m \left(\frac{d\mathbf{v}}{dt}\right)_{\text{rot}} = \mathbf{F}_{\text{inertial}} + \mathbf{F}_{\text{cor}} + \mathbf{F}_{\text{cent}} \][/tex]
where:
- [tex]\(\left(\frac{d\mathbf{v}}{dt}\right)_{\text{rot}}\)[/tex] is the rate of change of velocity of the particle with respect to the rotating frame.
- [tex]\(\mathbf{F}_{\text{inertial}}\)[/tex] is the force acting on the particle in the inertial frame.
- [tex]\(\mathbf{F}_{\text{cor}}\)[/tex] is the Coriolis force, which arises due to the rotation of the frame and acts perpendicular to the velocity of the particle.
- [tex]\(\mathbf{F}_{\text{cent}}\)[/tex]is the centrifugal force, which also arises due to the rotation of the frame and acts radially outward from the center of rotation.
The Coriolis force and the centrifugal force are additional apparent forces that appear in the equation of motion in a rotating frame.
(iii) Surface Shape of Water in a Spinning Bucket:
When a bucket of water spins about its symmetry axis at a uniform angular velocity, assuming the bucket is rotating in an inertial frame, the surface of the water in the bucket takes the shape of a parabola. This occurs due to the balance between gravity and the centrifugal force acting on the water particles.
Assumptions and Approximations:
- The bucket is assumed to be rotating at a constant angular velocity.
- The water is assumed to be in equilibrium, with no net acceleration.
- The surface of the water is assumed to be smooth and not affected by other external forces.
- The effects of surface tension and air resistance are neglected.
Under these assumptions, the shape of the water's surface conforms to a parabolic curve, as the centrifugal force counteracts the force of gravity, causing the water to rise higher at the edges and form a concave shape in the center.
Learn more about centrifugal force here:
https://brainly.com/question/545816
#SPJ11
Question 2: Find the bound currents of a uniformly magnetized sphere along the z-axis with dipole moment M.
The bound currents of a uniformly magnetized sphere along the z-axis with dipole moment M are zero:
[tex]$K_{\phi} = 0$[/tex]
The equation you provided for the bound currents along the z-axis of a uniformly magnetized sphere is correct:
[tex]$K_{\phi}=\frac{1}{\mu_{0}} \nabla \times \mathbf{M}$[/tex]
Starting from [tex]$\mathbf{M} = M \hat{z}$[/tex], we can substitute this value into the equation for the bound currents:
[tex]$K_{\phi}=\frac{1}{\mu_{0}} \nabla \times (M \hat{z})$[/tex]
Next, we can evaluate the curl using the formula you provided for the curl in cylindrical coordinates:
[tex]$\nabla \times \mathbf{V}=\frac{1}{r} \frac{\partial}{\partial z}(r V_{\phi})$[/tex]
However, it seems there was a mistake in the previous equation you presented, so I will correct it.
Applying the formula for the curl, we find that the only non-zero component in this case is indeed in the [tex]$\hat{\phi}$[/tex] direction. Therefore, we have:
[tex]$\nabla \times \mathbf{M} = \frac{1}{r} \frac{\partial}{\partial z}(r M_{\phi})$[/tex]
However, since [tex]$\mathbf{M} = M \hat{z}$[/tex], the [tex]$\phi$[/tex] component of [tex]$\mathbf{M}$[/tex] is zero ([tex]$M_{\phi} = 0$[/tex]), and as a result, the curl simplifies to:
[tex]$\nabla \times \mathbf{M} = 0$[/tex]
This means that the bound currents along the z-axis of a uniformly magnetized sphere are zero, as there are no non-zero components in the curl of the magnetization vector.
Therefore, the conclusion is that the bound currents of a uniformly magnetized sphere along the z-axis with dipole moment M are zero: [tex]$K_{\phi} = 0$[/tex]
Learn more about currents at: https://brainly.com/question/1100341
#SPJ11
Consider the signal x(t) = w(t) sin(27 ft) where f = 100 kHz and t is in units of seconds. (a) (5 points) For each of the following choices of w(t), explain whether or not it would make x(t) a narrowband signal. Justify your answer for each of the four choices; no marks awarded without valid justification. 1. w(t) = cos(2πt) 2. w(t) = cos(2πt) + sin(275t) 3. w(t) = cos(2π(f/2)t) where f is as above (100 kHz) 4. w(t) = cos(2π ft) where f is as above (100 kHz) (b) (5 points) The signal x(t), which henceforth is assumed to be narrowband, passes through an all- pass system with delays as follows: 3 ms group delay and 5 ms phase delay at 1 Hz; 4 ms group delay and 4 ms phase delay at 5 Hz; 5 ms group delay and 3 ms phase delay at 50 kHz; and 1 ms group delay and 2 ms phase delay at 100 kHz. What can we deduce about the output? Write down as best you can what the output y(t) will equal. Justify your answer; no marks awarded without valid justification. (c) (5 points) Assume x(t) is narrowband, and you have an ideal filter (with a single pass region and a single stop region and a sharp transition region) which passes w(t) but blocks sin(2 ft). (Specifically, if w(t) goes into the filter then w(t) comes out, while if sin (27 ft) goes in then 0 comes out. Moreover, the transition region is far from the frequency regions occupied by both w(t) and sin(27 ft).) What would the output of the filter be if x(t) were fed into it? Justify your answer; no marks awarded without valid justification.
a) 1. x(t) is not a narrowband signal if w(t) = cos(2πt).
2. x(t) is not a narrowband signal if w(t) = cos(2πt) + sin(275t).
3. x(t) is a narrowband signal if w(t) = cos(2π(f/2)t).
4. x(t) is a narrowband signal if w(t) = cos(2πft).
b) the output y(t) will be the same as the input signal x(t), except that it will have a different phase shift.
c) the output of the filter will be y(t) = w(t)sin(27 ft) -> w(t) * 0 = 0.
a) 1. w(t) = cos(2πt)
If we consider the Fourier transform of the signal x(t) and w(t), we find that x(t) can be represented by a series of sinewaves with frequencies between (f - Δf) and (f + Δf).
If we consider the function w(t) = cos(2πt) and take the Fourier transform, we find that the Fourier transform is non-zero for an infinite range of frequencies.
Therefore, x(t) is not a narrowband signal if w(t) = cos(2πt).
2. w(t) = cos(2πt) + sin(275t)
We can represent w(t) as a sum of two sinusoids with different frequencies. If we take the Fourier transform, we get non-zero values at two different frequencies.
Therefore, x(t) is not a narrowband signal if w(t) = cos(2πt) + sin(275t).
3. w(t) = cos(2π(f/2)t) where f is as above (100 kHz)
If we consider the function w(t) = cos(2π(f/2)t), the Fourier transform is zero for all frequencies outside the range (f/2 - Δf) to (f/2 + Δf).
Since this range is much smaller than the frequency range of x(t), we can say that
x(t) is a narrowband signal if w(t) = cos(2π(f/2)t).
4. w(t) = cos(2π ft) where f is as above (100 kHz)If we consider the function w(t) = cos(2πft), the Fourier transform is zero for all frequencies outside the range (f - Δf) to (f + Δf).
Since this range is much smaller than the frequency range of x(t), we can say that
x(t) is a narrowband signal if w(t) = cos(2πft).
b)The signal x(t) is passed through an all-pass system with delays. The output y(t) will have the same spectral shape as the input signal x(t), but with a different phase shift. In this case, the phase shift is given by the phase delays of the all-pass system. The group delays have no effect on the spectral shape of the output signal.
Therefore, the output y(t) will be the same as the input signal x(t), except that it will have a different phase shift.
c) Since the ideal filter only allows the signal w(t) to pass through, we can simply replace sin(27 ft) with 0 in the expression for x(t).
Therefore, the output of the filter will be y(t) = w(t)sin(27 ft) -> w(t) * 0 = 0.
Learn more about narrowband signal here:
https://brainly.com/question/30931845
#SPJ11
You throw a stone horizontally at a speed of 10 m/s from the top of a cliff that is 50 m high. How far from the base of the cliff does the stone hit the ground within time of 8 s. * (20 Points) 80 m 50 m 10 m 8 m
The stone will hit the ground at a distance of 80 meters from the base of the cliff within the time of 8 seconds after it is thrown, which makes the correct option B (80 m).
To determine how far from the base of the cliff does the stone hit the ground within the time of 8 seconds after it is thrown, we'll need to make use of the equation:s = ut + 1/2gt²,Where, s = distance, u = initial velocity, t = time, g = acceleration due to gravity and this equation is applicable only when the motion is under the influence of gravity, in this case, vertical motion. As we know the stone is being thrown horizontally, the acceleration due to gravity will not affect the horizontal motion.So, in this case, u = 10 m/s (initial velocity, because it is thrown horizontally), g = 9.8 m/s² (acceleration due to gravity) and h = 50 m (height of the cliff).
Using this equation, we can get the time it takes for the stone to reach the ground:50 = 0 + 1/2 x 9.8 x t²25 = 4.9t²5.102 = t (square root of both sides)t ≈ 2.26 sSince the stone is being thrown horizontally, it covers the distance d = vt, where v is the horizontal velocity and t is the time. The horizontal velocity remains constant throughout the motion. In this case, we have:v = 10 m/s (horizontal velocity) and t = 8 s,So, d = vt = 10 x 8 = 80 mHence, the stone will hit the ground at a distance of 80 meters from the base of the cliff within the time of 8 seconds after it is thrown, which makes the correct option B (80 m).
Learn more about Equation here,What is equation? Define equation
https://brainly.com/question/29174899
#SPJ11
The figure shows an approximate plot of force magnitude F versus time t during the collision of a 57 g Superball with a wall. The initial velocity of the ball is 31 m/s perpendicular to the wall, in the negative direction of an x axis. It rebounds directly back with approximately the same speed, also perpendicular to the wall. What is F max
, the maximum magnitude of the force on the ball from the wall during the collision? Number Units An object, with mass 97 kg and speed 14 m/s relative to an observer, explodes into two pieces, one 3 times as massive as the other; the explosion takes place in deep space. The less massive piece stops relative to the observer. How much kinetic energy is added to the system during the explosion, as measured in the observer's reference frame? Number Units A 4.2 kg mess kit sliding on a frictionless surface explodes into two 2.1 kg parts, one moving at 2.6 m/s, due north, and the other at 5.9 m/s,16 ∘
north of east. What is the original speed of the mess kit? Number Units A vessel at rest at the origin of an xy coordinate system explodes into three pieces. Just after the explosion, one piece, of mass m, moves with velocity (−45 m/s) i
^
and a second piece, also of mass m, moves with velocity (−45 m/s) j
^
. The third piece has mass 3 m. Jus after the explosion, what are the (a) magnitude and (b) direction (as an angle relative to the +x axis) of the velocity of the third piece (a) Number Units (b) Number Units
For part 1:
Given that, Mass of superball, m = 57 g = 0.057 kg Initial velocity of the ball, u = -31 m/s
Final velocity of the ball, v = +31 m/sChange in velocity, Δv = v - u = 31 - (-31) = 62 m/s
Time taken for the collision, t = 2L / Δv, where, L is the length of the superball
Maximum force, Fmax = Δp / t, where, Δp is the change in momentum of the ball.
Δp = mΔv = 0.057 x 62 = 3.534 Ns.t = 2L / Δv = 2(0.037)/ 62 = 0.00037 sFmax = Δp / t = (3.534 Ns) / (0.00037 s) = 9.54 x 10^3 N
For part 2:
Mass of the object, m = 97 kg, Velocity of the object, v = 14 m/sLet m1 and m2 be the masses of the two pieces created after the explosion. Then, m1 + m2 = 97 kg
Since the less massive piece stops relative to the observer, we can write,m1 x v1 = m2 x v2, where v1 is the velocity of the more massive piece, and v2 is the velocity of the less massive piece.
Since m1 = 3m2, we can write v2 = (3v1) / 4
Kinetic energy before the explosion, KE1 = (1/2) m v² = (1/2) x 97 x 14² = 9604 J
Let KE2 be the total kinetic energy after the explosion, then, KE2 = (1/2) m1 v1² + (1/2) m2 v2²
Substituting the value of v2 in terms of v1, KE2 = (1/2) m1 v1² + (1/2) m2 [(3v1) / 4]²= (1/2) m1 v1² + (27/32) m1 v1²= (59/32) m1 v1²
Total kinetic energy added during the explosion = KE2 - KE1= (59/32) m1 v1² - (1/2) m v²= (59/32) m1 v1² - 4802 J
Since we have one equation (m1 + m2 = 97 kg) and two unknowns (m1, v1).
To learn about kinetic energy here:
https://brainly.com/question/8101588
#SPJ11
A 2.4 kg rock has a horizontal velocity of magnitude v=2.1 m/s when it is at point P in the figure, where r=4.1 m and θ= 45 degree. If the only force acting on the rock is its weight, what is the rate of change of its angular momentum relative to point O at this instant?
Therefore, the rate of change of the angular momentum relative to point O is zero.Answer: 0
The angular momentum of the rock relative to point O is given byL = r × p,where r is the position vector of the rock relative to point O, and p is the momentum of the rock relative to point O.We can express the momentum p in terms of the velocity v. Since the rock has a horizontal velocity of magnitude v=2.1 m/s, its momentum has a horizontal component of p = mv = (2.4 kg)(2.1 m/s) = 5.04 kg · m/s. There is no vertical component of the momentum, since the rock is moving horizontally, so we have p = (5.04 kg · m/s) i. Using the position vector r = (4.1 m) i + (4.1 m) j and the momentum p, we find thatL = r × p= [(4.1 m) i + (4.1 m) j] × (5.04 kg · m/s i)= 20.2 kg · m²/s k. where k is a unit vector perpendicular to the plane of the paper, pointing out of the page. The rate of change of the angular momentum relative to point O is given byτ = dL/dtwhere τ is the torque on the rock. Since the only force acting on the rock is its weight, which is directed downward, the torque on the rock is zero, so we haveτ = 0. Therefore, the rate of change of the angular momentum relative to point O is zero.Answer: 0
To know more about magnitude visit:
https://brainly.com/question/29665153
#SPJ11
The masses of the two particles at position are each m,m₂ and there is only an internal force acting on the two particles, each F₁-F₁, F2=-F₂1 (Here, F > 0, ) Show that the and ₁=(-/- net torque of the two particle systems is 0.
To show that the net torque of the two-particle system is zero, we need to consider the torque acting on each particle individually and sum them up.
For particle 1, the torque is given by τ₁ = r₁ × F₁, where r₁ is the position vector of particle 1 and F₁ is the internal force acting on it. Since F₁ and r₁ are parallel, their cross product is zero, so τ₁ = 0.
For particle 2, the torque is given by τ₂ = r₂ × F₂, where r₂ is the position vector of particle 2 and F₂ is the internal force acting on it. Similarly, since F₂ and r₂ are parallel, their cross product is zero, so τ₂ = 0.
Now, to find the net torque of the system, we can sum up the individual torques: Net torque = τ₁ + τ₂ = 0 + 0 = 0.
Therefore, the net torque of the two-particle system is indeed zero.
Learn more about torque here:
https://brainly.com/question/17512177
#SPJ11
A 17.5-cm-diameter loop of wire is initially oriented perpendicular to a 1.5-T magnetic field. The loop is rotated so that its plane is parallel to the field direction in 0.29 S. What is the average induced emf in the loop?
A 17.5-cm-diameter loop of wire is initially oriented perpendicular to a 1.5-T magnetic field. Therefore, the average induced emf in the loop is 0.125 V.
The average induced emf in the loop can be found out as follows: Formula used: Average induced emf = (BAN)/t
Where, B = Magnetic Field, A = Area of the loop, N = Number of turns of wire, t = time required to rotate the loop (or time in which the magnetic flux changes)
Given that, Diameter of the loop = 17.5 cm, Radius of the loop = r = Diameter / 2 = 17.5 / 2 cm = 8.75 cm = 0.0875 m, Magnetic field strength = B = 1.5 T, Time required to rotate the loop = t = 0.29 s.
Now, we need to find the area of the loop and number of turns of wire.
Area of the loop = πr² = 3.14 × (0.0875 m)² = 0.024 m²
Number of turns of wire = 1 (as only one loop is given)Now, we can substitute these values in the formula of average induced emf to calculate the answer.
Average induced emf = (BAN)/t= (1.5) × (0.024) × (1) / (0.29)= 0.125 V
Therefore, the average induced emf in the loop is 0.125 V.
Learn more about magnetic field here:
https://brainly.com/question/19542022
#SPJ11
: A particle is moving in a circular path in the x-y plane. The center of the circle is at the origin and the rotation is counterclockwise at a rate (angular speed) of o = 6.58 rad's. At time t= 0, the particle is at y = and x = 4.04 m. * 17% Part (a) What is the x coordinate of the particle, in meters, at 1 = 24.5 s? x=3.18 X Attempts Remain * 17% Part (b) What is the y coordinate of the particle, in meters, at 1 = 24.5 s? y= 1.301 X Attempts Remain 4 17% Part (c) What is the x component of the particle's velocity, in m's, at t = 24.5 s? 4 17% Part (d) What is the y component of the particle's velocity, in m/s, al 1 24.5 s? A 17% Part (e) What is the x component of the particle's acceleration, in m's?, at t = 24.5 s? A 17% Part (1) What is the y component of the particle's acceleration, in m/s2, at 1 = 24.5 s? ay Grade Summary Deductions 0% Potential 100%
The x coordinate of the particle is 3.18m. The y coordinate of the particle is 1.301 m. The x and y component of the particle's velocity is -20.942 m/s, and 8.556 m/s. The x and y component of the particle's acceleration is [tex]-136.45 m/s^2[/tex], and [tex]-57.602 m/s^2[/tex].
a) For the x coordinate at t=24.5 s, formula use is: x = r * cos(θ), where r is the radius of the circle and θ is the angle covered by the particle. Since the angular speed is given as ω = 6.58 rad/s, the angle covered after time t is [tex]\theta = \omega * t[/tex]. The particle starts at x=4.04 m, substituting the values into the equation. Hence x=3.18 m.
b) For the y coordinate at t=24.5 s, formula use is: y = r * sin(θ). Following the same approach as before, hence y=1.301 m.
c)For the x component of the particle's velocity, differentiate the x equation with respect to time.
[tex]vx = -r * \omega * sin(\theta)[/tex]
Plugging in the values,
vx = -6.58 * 3.18 = -20.942 m/s.
d) Similarly, the y component of the velocity (vy) is:
[tex]vy = r * \omega * cos(\theta)[/tex]
Substituting the values,
vy = 6.58 * 1.301 = 8.556 m/s.
e) As for the acceleration components, the x component (ax) can be determined by differentiating the x component of velocity with respect to time.
[tex]ax = -r * \omega^2 * cos(\theta)[/tex]
Plugging in the values
[tex]ax = -6.58^2 * 3.18 = -136.45 m/s^2[/tex].
Lastly, the y component of acceleration (ay) is obtained by differentiating the y component of velocity with respect to time,
[tex]ay =[/tex] [tex]-r * \omega^2 * sin(\theta)[/tex]
Substituting the values,
[tex]ay =[/tex] [tex]-6.58^2 * 1.301 = -57.602 m/s^2[/tex].
Learn more about angular speed here:
https://brainly.com/question/29058152
#SPJ11
A coil is wrapped with 191 turns of wire around the perimeter of a circular frame (radius = 9 cm). Each turn has the same area, equal to that of the circular frame. A uniform magnetic field perpendicular to the plane of the coil is activated. This field changes at a constant rate of 20 to 80 mT in a time of 2 ms. What is the magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT? Give your answer to two decimal places.
The magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT is approximately 7.64 V.
Number of turns = 191
Radius = 9 cm = 0.09 m
Initial magnetic field = 20 mT
Final magnetic field = 80 mT
Time = 2 ms = 2 x 10^-3 s
The induced emf in the coil is given by Faraday's law:
ε = -N∆B/∆t
where ε is the induced emf, N is the number of turns, ∆B is the change in magnetic field, and ∆t is the time interval.
Substituting the given values, we get:
ε = -191 × (80 - 20) mT / 2 x 10^-3 s
ε = -7640 mT/s
The magnitude of the induced emf is 7640 mV. Rounding to two decimal places, we get:
ε = 7640.0 mV = 7.64 V
Therefore, the magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT is 7.64 V.
Learn more about induced emf https://brainly.com/question/13744192
#SPJ11
A commuter airplane starts from an airport and takes the following route: The plane first flies to city A, located 175 km away in a direction 30.0° north of east. Next, it flies for 150. km 20.0° west of north, to city B. Finally, the plane flies 190. km due west, to city C. Find the location of city C relative to the location of the starting point. (Hint: Draw a diagram on an xy-plane. Draw the start of a new vector from the end of the previous one, also known as, tip - to - toe method.)
The location of city C relative to the location of the starting point is (-30 km, 255 km).
The plane first flies to city A, located 175 km away in a direction 30.0° north of east. Next, it flies for 150. km 20.0° west of north, to city B. Finally, the plane flies 190. km due west, to city C.To find the location of city C relative to the location of the starting point, we need to draw a diagram on an xy-plane using the tip-to-toe method. This is the route of plane.
Let us assume the starting point as O and point C as (x, y) and find the values of x and y using the given data.From the starting point O, the plane flies to city A, located 175 km away in a direction 30.0° north of east.Now, from the starting point, O draw a vector 175 km in the direction 30.0° north of east. Let the end of this vector be P.From the end of the vector OP, draw a vector 150 km in the direction 20.0° west of north. Let the end of this vector be Q.From the end of the vector OQ, draw a vector 190 km in the due west direction. Let the end of this vector be R.Then, join OR as shown in the figure below. From the figure, we can see that the coordinates of R are (-30 km, 255 km).
Therefore, the location of city C relative to the location of the starting point is (-30 km, 255 km).
Learn more about location:
https://brainly.com/question/28173702
#SPJ11
For an instrumentation amplifier of the type shown in Fig. 2.20(b), a designer proposes to make R₂ R3 = R4 = 100 ks2, and 2R₁ = 10 k. For ideal components, what difference-mode gain, common-mode gain, and CMRR result? Reevaluate the worst-case values for these for the situation in which all resistors are specified as ±1% units. Repeat the latter analysis for the case in which 2R₁ is reduced to 1 k2. What do you conclude about the effect of the gain of the first stage on CMRR? (Hint) 2/10- 1/2 2R₁ A₁ R₂ www www R₂ R₂ www R₂ ww R₁ R₁ www (b) Figure 2.20 (b) A popular circuit for an instrumentation amplifier: The circuit in (a) with the connection between node X and ground removed and the two resistors R₁ and R₁ lumped together.
The common-mode gain (ACM) decreases when the value of the gain of the first stage decreases.
For ideal components, the difference-mode gain, common-mode gain, and CMRR can be determined. It is proposed to make
R₂R3 = R4 = 100 kΩ,
2R₁ = 10 kΩ
The circuit diagram of an instrumentation amplifier is given below:
In the given circuit, the value of the resistor 2R1 has been given as 10 kΩ, which means that R1 is equal to 5 kΩ. R2 and R3 are equal to 100 kΩ, and R4 is equal to 100 kΩ.
For ideal components, the difference-mode gain (AD), common-mode gain (ACM), and CMRR can be calculated as follows:
Difference-mode gain:
AD = - (R4 / R3) x (2R1 / R2)
AD = - (100 kΩ / 100 kΩ) x (2 x 5 kΩ / 100 kΩ)
AD = - 0.02 or -40 dB
Common-mode gain:
ACM = 1 + (2R1 / R2)
ACM = 1 + (2 x 5 kΩ / 100 kΩ)
ACM = 1.1 or 20 dB
Common-Mode Rejection Ratio (CMRR):
CMRR = AD / ACM
CMRR = - 0.02 / 1.1
CMRR = - 0.0182 or 25.3 dB
Now, reevaluating the worst-case values of AD, ACM, and CMRR when all resistors are specified as ±1% units:
For AD:
When all resistors are specified as ±1% units, the value of the difference-mode gain (AD) can be calculated as follows:
AD = - (R4 / R3) x (2R1 / R2)
ADmin = - (101 kΩ / 99 kΩ) x (2 x 4.95 kΩ / 100 kΩ)
ADmin = - 0.02 x 0.099495 or -39.6 dB
ADmax = - (99 kΩ / 101 kΩ) x (2 x 5.05 kΩ / 100 kΩ)
ADmax = - 0.02 x 1.009901 or -40.2 dB
For ACM:
When all resistors are specified as ±1% units, the value of the common-mode gain (ACM) can be calculated as follows:
ACMmin = 1 + (2 x 4.95 kΩ / 100 kΩ)
ACMmin = 1.099 or 20.5 dB
ACMmax = 1 + (2 x 5.05 kΩ / 100 kΩ)
ACMmax = 1.101 or 20.6 dB
For CMRR:
When all resistors are specified as ±1% units, the value of the CMRR can be calculated as follows:
CMRRmin = ADmax / ACMmin
CMRRmin = - 40.2 dB / 20.5 dB or -19.6 dB
CMRRmax = ADmin / ACMmax
CMRRmax = - 39.6 dB / 20.6 dB or -19.2 dB
Now, considering the case where 2R1 is reduced to 1 kΩ:
In this case, 2R1 = 1 kΩ, which means that R1 is equal to 0.5 kΩ. The values of R2, R3, and R4 are equal to 100 kΩ, and all the resistors are specified as ±1% units.
Difference-mode gain:
AD = - (R4 / R3) x (2R1 / R2)
AD = - (100 kΩ / 100 kΩ) x (2 x 0.5 kΩ / 100 kΩ)
AD = - 0.01 or -20 dB
Common-mode gain:
ACM = 1 + (2R1 / R2)
ACM = 1 + (2 x 0.5 kΩ / 100 kΩ)
ACM = 1.01 or 0.43 dB
Common-Mode Rejection Ratio (CMRR):
CMRR = AD / ACM
CMRR = - 0.01 / 1.01
CMRR = - 0.0099 or -40.2 dB
The common-mode gain (ACM) decreases when the value of the gain of the first stage decreases. However, the CMRR is not affected by the value of the gain of the first stage.
Learn more about CMRR:
https://brainly.com/question/29774359
#SPJ11
What is the output voltage of a 3.00-V lithium cell in a digital wristwatch that draws 0.670 mA, if the cell's internal resistance is 2.25 Ω? (Enter your answer to at least five significant figures.) V
The output voltage of a 3.00-V lithium cell in a digital wristwatch, considering its internal resistance of 2.25 Ω, is approximately 1.5075 V which is determined using Ohm's Law and should be calculated to at least five significant figures.
To calculate the output voltage, we can use Ohm's Law, which states that voltage (V) is equal to the current (I) multiplied by the resistance (R). In this case, the current drawn by the wristwatch is given as 0.670 mA, and the internal resistance of the cell is 2.25 Ω. Thus, we can calculate the voltage as follows:
V = I * R
= 0.670 mA * 2.25 Ω
= 1.5075 mV
Since the given lithium cell has an initial voltage of 3.00 V, the output voltage will be slightly lower due to the internal resistance. Therefore, the output voltage of the lithium cell in the digital wristwatch is approximately 1.5075 V when rounded to five significant figures.
Learn more about Ohm's Law here:
https://brainly.com/question/1247379
#SPJ11
Amount of heat required to raise temperature of 10gm water through 2 deg * C is
The amount of heat required to raise the temperature of 10 g of water through 2°C is 83.68 Joules.
To determine the amount of heat required to raise the temperature of 10 g of water through 2°C, we will use the formula:Q = m × c × ΔT
Where Q is the amount of heat required, m is the mass of the substance being heated, c is the specific heat capacity of the substance, and ΔT is the change in temperature.
So, for 10 g of water, the mass (m) would be 10 g.
The specific heat capacity (c) of water is 4.184 J/(g°C), so we'll use that value.
And the change in temperature (ΔT) is 2°C.
Substituting these values into the formula, we get:Q = 10 g × 4.184 J/(g°C) × 2°CQ = 83.68 Joules
Therefore, the amount of heat required to raise the temperature of 10 g of water through 2°C is 83.68 Joules.
For more questions on temperature
https://brainly.com/question/25677592
#SPJ8
A light beam is traveling through an unknown substance. When it strikes a boundary between that substance and the air (Nair = 1), the angle of reflection is 29.0° and the angle of refraction is 36.0°. What is the index of refraction n of the substance? n =
The index of refraction n of the substance is 0.82.
The index of refraction of a substance can be calculated using Snell's law.
Snell's law states that: n1sinθ1 = n2sinθ2, where n1 is the refractive index of the first medium (in this case air), θ1 is the angle of incidence, n2 is the refractive index of the second medium (the unknown substance), and θ2 is the angle of refraction.
Given that a light beam is traveling through an unknown substance and when it strikes a boundary between that substance and the air (Nair = 1), the angle of reflection is 29.0° and the angle of refraction is 36.0°, we are required to find the index of refraction n of the substance.
We can use the formula: n1sinθ1 = n2sinθ2 where n1=1, θ1 = 29.0°, and θ2 = 36.0° to find the refractive index of the unknown substance.
The first step is to calculate sin θ1 and sin θ2 using a scientific calculator: sin θ1 = sin 29.0° = 0.4848 and sin θ2 = sin 36.0° = 0.5878
Substitute the given values in the formula: n1sinθ1 = n2sinθ2
Substituting the known values, we get:1 × 0.4848 = n2 × 0.5878
Dividing both sides by 0.5878 we get: n2 = (1 × 0.4848) / 0.5878
n2 = 0.82
Therefore, the index of refraction n of the substance is 0.82.
Learn more about index of refraction: brainly.com/question/12469161
#SPJ11
Two light spheres each of mass 2.0g are suspended by light strings 10cm in length. A uniform electric field |E| = 4.42 × 105N/C is applied in the horizontal direction. The charges on the spheres are equal and opposite. For what charge values will the spheres be in equilibrium at an angle θ = 10 degrees? *I believe the answer is supposed to be 5 x 10^-8 C but that's not what I'm getting.*
To achieve equilibrium for two light spheres suspended by light strings in the presence of a uniform electric field, the charges on the spheres must have specific values.
In this case, with a given angle of 10 degrees and other known parameters, the expected charge value is 5 × 10^-8 C. However, the calculated value may differ.
To find the charge values that result in equilibrium, we can use the principle of electrostatic equilibrium. The gravitational force acting on each sphere must be balanced by the electrostatic force due to the electric field.
The gravitational force can be determined by considering the mass and gravitational acceleration, while the electrostatic force depends on the charges, the electric field strength, and the distance between the charges. By equating these forces and solving the equations, we can find the charge values that satisfy the given conditions.
It's important to note that slight variations in calculations or rounding can lead to small differences in the final result, which may explain the deviation from the expected value.
Learn more about electrostatic equilibrium here:
https://brainly.com/question/32825729
#SPJ11
Why is a fission chain reaction more likely to occur in a big piece of uranium than in a small piece?
A fission chain reaction is more likely to occur in a big piece of uranium compared to a small piece due to several reasons Neutron population, Neutron leakage,Critical mass,Surface-to-volume ratio
A fission chain reaction is more likely to occur in a big piece of uranium compared to a small piece due to several reasons:
Neutron population: In a fission chain reaction, a uranium nucleus absorbs a neutron, becomes unstable, and splits into two smaller nuclei, releasing multiple neutrons. These released neutrons can then induce fission in neighboring uranium nuclei, leading to a chain reaction. A larger piece of uranium contains a higher number of uranium nuclei, increasing the probability of neutron-nucleus interactions and sustaining the chain reaction. Neutron leakage: Neutrons released during fission can escape or be absorbed by non-fissionable materials, reducing the number available to induce fission. In a larger piece of uranium, the probability of neutron leakage is lower since there is more uranium material to capture and retain the neutrons within the system, allowing for more opportunities for fission events. Critical mass: Fission requires a certain minimum mass of fissile material, known as the critical mass, to sustain a self-sustaining chain reaction. In a small piece of uranium, the mass may be below the critical mass, and thus the chain reaction cannot be sustained. However, in a larger piece, the mass exceeds the critical mass, providing enough fissile material to sustain the chain reaction. Surface-to-volume ratio: A larger piece of uranium has a smaller surface-to-volume ratio compared to a smaller piece. The surface of the uranium can act as a source of neutron leakage, with more neutrons escaping without inducing fission. A smaller surface-to-volume ratio in a larger piece reduces the proportion of neutrons lost to leakage, allowing more neutrons to interact with uranium nuclei and sustain the chain reaction.These factors collectively contribute to the increased likelihood of a fission chain reaction occurring in a big piece of uranium compared to a small piece. It is important to note that maintaining a controlled chain reaction requires careful design and control mechanisms to prevent uncontrolled releases of energy and radiation.
To learn more about Critical mass visit: https://brainly.com/question/12814600
#SPJ11
A proton is observed traveling with some velocity V perpendicular to a uniform magnetic field B. Which of the following statements are true in regard to the direction of the magnetic force exerted on the proton? a)The magnetic force is parallel to the proton's velocity and perpendicular to the magnetic field. o b) The magnetic force is parallel to the proton's velocity and parallel to the magnetic field. O The magnetic force is perpendicular to the proton's velocity and perpendicular to the magnetic field. O d) The magnetic force is ON e) None of the above.
The correct statement is that the magnetic force is perpendicular to the proton's velocity and perpendicular to the magnetic field.
According to the right-hand rule for magnetic forces, the direction of the magnetic force experienced by a charged particle moving through a magnetic field is perpendicular to both the velocity of the particle and the magnetic field.
In this case, the proton is observed traveling with a velocity V perpendicular to the uniform magnetic field B. As a result, the magnetic force exerted on the proton will be perpendicular to both V and B. This means that option c) "The magnetic force is perpendicular to the proton's velocity and perpendicular to the magnetic field" is the correct statement.
Option a) is incorrect because the magnetic force is not parallel to the proton's velocity. Option b) is incorrect because the magnetic force is not parallel to the magnetic field. Option d) is incomplete and does not provide any information.
Learn more about magnetic field here:
https://brainly.com/question/14848188
#SPJ11
A wire of length L = 0.52 m and a thickness diameter d = 0.24 mm is wrapped into N = 7137 circular turns to construct a solenoid. The cross sectional area A of each circular coil is 4.9 cm² and the length of the solenoid is 35 cm. The solenoid is then connected to a battery of 20 V and the switch closes for a very long time. Determine the strength of the magnetic field B (mT) produced inside its coils. Give answer to two places to the right of the decimal.
The magnetic field inside the solenoid is 30.4 mT.
To determine the strength of the magnetic field inside the solenoid, we can use the formula for the magnetic field produced by a solenoid:
B = (μ₀ * N * I) / L
Where:
- B is the magnetic field strength
- μ₀ is the permeability of free space (μ₀ ≈ 4π x 10^-7 T·m/A)
- N is the number of turns in the solenoid
- I is the current flowing through the solenoid
- L is the length of the solenoid
To find the current flowing through the solenoid, we can use Ohm's law:
I = V / R
Where:
- I is the current
- V is the voltage
- R is the resistance
The resistance of the solenoid can be calculated using the formula:
R = (ρ * L) / A
Where:
- ρ is the resistivity of the wire material
- L is the length of the solenoid
- A is the cross-sectional area of each circular coil
Let's calculate step by step:
L = 0.52 m
d = 0.24 mm = 0.24 x 10^-3 m
N = 7137
A = 4.9 cm² = 4.9 x 10^-4 m²
length of solenoid = 35 cm = 35 x 10^-2 m
V = 20 V
First, we need to calculate the resistance R:
R = (ρ * L) / A
To calculate ρ, we need to know the resistivity of the wire material. Assuming it is copper, the resistivity of copper is approximately 1.68 x 10^-8 Ω·m.
ρ ≈ 1.68 x 10^-8 Ω·m
Substituting the values:
R = (1.68 x 10^-8 Ω·m * 0.52 m) / (4.9 x 10^-4 m²)
Calculating:
R ≈ 1.77 Ω
Next, we can calculate the current I:
I = V / R
Substituting the values:
I = 20 V / 1.77 Ω
Calculating:
I ≈ 11.30 A
Now we can calculate the magnetic field B:
B = (μ₀ * N * I) / L
Substituting the values:
B = (4π x 10^-7 T·m/A * 7137 * 11.30 A) / 0.52 m
Calculating:
B ≈ 0.0304 T
Finally, we convert the magnetic field to millitesla (mT) by multiplying by 1000:
B ≈ 30.4 mT
Therefore, the strength of the magnetic field inside the solenoid is approximately 30.4 mT.
Learn more about magnetic field of solenoid https://brainly.com/question/1873362
#SPJ11
A single-turn square loop carries a current of 16 A. The loop is 15 cm on a side and has a mass of 3.6×10 −2
kg - initially the loop lies flat on a horizontal tabletop. When a horizontal magnetic field is turned on, it is found that only one side of the loop experiences an upward force. Part A Find the minimum magnetic field, B min
, necessary to start lipping the loop up from the table. Express your answer using two significant figures. Researchers have tracked the head and body movements of several flying insects, including blowllies, hover fles, and honeybees. They attach lightweight, fexible wires to a small metai coli on the insect's head, and another-on its thorax, and then allow it to fly in a stationary magnetic field. As the coils move through the feld, they experience induced emts that can be analyzed by computer to determine the corresponding orientation of the head and thorax. Suppose the fly turns through an angle of 90 in 31 ms. The coll has 89 turns of wire and a diameter of 2.2 mm. The fly is immersed in a magnetic feld of magnitude 0.16 m T. Part A If the magnetic flux through one of the coils on the insect goes from a maximum to zero during this maneuver find the magnitude of the induced emf. Express your answer using two significant figures.
For the loop, the minimum magnetic field required to lift it from the table is approximately 0.24 T.
As for the flying insect, the magnitude of the induced emf in the coil due to a change in magnetic flux is approximately 0.29 mV. For the square loop, we equate the magnetic force with the gravitational force. Magnetic force is given by BIL where B is the magnetic field, I is the current, and L is the length of the side. Gravitational force is mg, where m is mass and g is gravitational acceleration. Setting BIL=mg and solving for B gives us the minimum magnetic field. For the insect, the change in magnetic flux through the coil induces an emf according to Faraday's law, given by ΔΦ/Δt = N*emf, where N is the number of turns and Δt is the time taken. Solving for emf provides the induced voltage.
Learn more about magnetic forces here:
https://brainly.com/question/33127932
#SPJ11
Two waves on one string are described by the wave functions
y1= 2.05 cos(3.05x − 1.52t)
y2= 4.54 sin(3.31x − 2.39t)
where x and y are in centimeters and t is in seconds. (Remember that the arguments of the trigonometric functions are in radians.)
(a) Find the superposition of the waves y_1 + y_2y1+y2 at x = 1.0, t = 0.0 s.
Two waves on one string are described by the wave functions y1= 2.05 cos(3.05x − 1.52t),y2= 4.54 sin(3.31x − 2.39t)where x and y are in centimeters and t is in seconds.The superposition of the waves y1 + y2 at x = 1.0 cm and t = 0.0 s is approximately 2.099968 cm.
To find the superposition of the waves at a specific point (x, t), we need to add the values of the two wave functions at that point.
Given:
y1 = 2.05 cos(3.05x - 1.52t)
y2 = 4.54 sin(3.31x - 2.39t)
x = 1.0 cm
t = 0.0 s
We can substitute the given values into the wave functions and perform the addition.
y1 + y2 = 2.05 cos(3.05x - 1.52t) + 4.54 sin(3.31x - 2.39t)
Substituting x = 1.0 cm and t = 0.0 s:
y1 + y2 = 2.05 cos(3.05(1.0) - 1.52(0.0)) + 4.54 sin(3.31(1.0) - 2.39(0.0))
y1 + y2 = 2.05 cos(3.05) + 4.54 sin(3.31)
Using a calculator, evaluate the cosine and sine functions:
y1 + y2 ≈ 2.05 * 0.999702 + 4.54 * 0.011432
y1 + y2 ≈ 2.048031 + 0.051937
y1 + y2 ≈ 2.099968
Therefore, the superposition of the waves y1 + y2 at x = 1.0 cm and t = 0.0 s is approximately 2.099968 cm.
To learn more about superposition of the waves visit: Vhttps://brainly.com/question/31952905
#SPJ11
A radio transmitter broadcasts at a frequency of 96,600 Hz. What is the wavelength of the wave in meters? Your Answer: Answer units Question 20 (1 point) What is the wavelength (in nanometers) of the peak of the blackbody radiation curve for something at 1,600 kelvins?
a. To determine the wavelength of a radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law.
a. For the radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f, where v is the speed of light (approximately 3.00 x 10^8 meters per second), λ is the wavelength (in meters), and f is the frequency. Rearranging the equation, we have λ = v / f. By substituting the given values, we can calculate the wavelength of the radio wave.
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law. According to the law, the peak wavelength is inversely proportional to the temperature. The formula is given as λ = (b / T), where λ is the wavelength (in meters), b is Wien's displacement constant (approximately 2.90 x 10^(-3) meters per kelvin), and T is the temperature in kelvins. By substituting the given temperature, we can calculate the wavelength in meters. To convert the wavelength to nanometers, we can multiply the value by 10^9, as there are 10^9 nanometers in a meter.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
Calculate the kinetic energy (in eV) of a nonrelativistic neutron that has a de Broglie wavelength of 12.10 x 10⁻¹² m. Give your answer accurate to three decimal places. Note that: mₙₑᵤₜᵣₒₙ = 1.675 x 10⁻²⁷ kg, and h = 6.626 X 10⁻³⁴ J.s, and 1 eV = 1.602 x 10⁻¹⁹J.
The kinetic energy of the nonrelativistic neutron with a De Broglie wavelength of 12.10 x 10⁻¹² m is approximately 4.08 eV.
De Broglie wavelength of a neutron, λ = 12.10 x 10⁻¹² m
Mass of the neutron, m = 1.675 x 10⁻²⁷ kg
Planck's constant, h = 6.626 x 10⁻³⁴ J.s
1 eV = 1.602 x 10⁻¹⁹ J
To find: The kinetic energy (K.E.) of the nonrelativistic neutron with a De Broglie wavelength of 12.10 x 10⁻¹² m.
First, convert the wavelength from nanometers to meters:
λ = 12.10 x 10⁻⁹ m
The formula for kinetic energy is given as:
K.E. = (h²/2m) (1/λ²)
Substituting the given values:
K.E. = [(6.626 x 10⁻³⁴)² / 2(1.675 x 10⁻²⁷)] (1 / (12.10 x 10⁻⁹)²)
Calculating the expression:
K.E. = 0.656 x 10⁻³² J
Since 1 eV = 1.602 x 10⁻¹⁹ J, convert the kinetic energy to electron volts:
0.656 x 10⁻³² J = 4.08 eV (approximately)
Therefore, the kinetic energy of the nonrelativistic neutron with a De Broglie wavelength of 12.10 x 10⁻¹² m is approximately 4.08 eV.
Learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11
What is the estimated volume of the table tennis ball?
cm3
What is the estimated volume of the golf ball?
cm3
Answer:
The estimated volume of a standard table tennis ball is approximately 2.7 cm³.
The estimated volume of a standard golf ball is approximately 41.6 cm³.
Explanation:
Find the system output y(t) of a linear and time-invariant system with the input x(t) and the impulse response h(t) as shown in Figure 1. Sketch y(t) with proper labelling. Figure 1 (13 Marks) (b) The message signal m(t)=5cos(2000πt) is used to modulate a carrier signal c(t)=4cos(80000πt) in a conventional amplitude modulation (AM) scheme to produce the AM signal, x AM
(t), in which the amplitude sensitivity factor of the modulator k a
is used. (i) Express the AM signal x AM
(t) and find its modulation index. (ii) Determine the range of k a
for the case of under-modulation. (iii) Is under-modulation or over-modulation required? Why? (iv) Determine the bandwidths of m(t) and x AM
(t), respectively.
(i)The modulation index of the given signal is 5ka/2000. (ii)For under modulation: modulation index ≤ 1/3 . (iv) The bandwidths of m(t) and xAM(t) are 2000 Hz and 1.64 MHz (approx), respectively.
a)System input x(t):y(t)=5∫0tx(τ)h(t-τ)dτ=5∫0t5τe^(-2τ)u(t-τ)dτ=25∫0tτe^(-2τ)u(t-τ)dτ. Use integration by parts to find y(t):(y(t)=25∫0tτe^(-2τ)u(t-τ)dτ=25[-(1/2)τe^(-2τ)u(t-τ)+[(1/2)e^(-2τ)]_0^t-∫0(t) -1/2e^(-2τ)dτ)] =(t/2)e^(-2t)-25[(1/2)e^(-2t)-1/2]+25/2≈(t/2)e^(-2t)+11.25.
b)(i) Expression of AM signal, xAM(t) is:xAM(t)=(4+5ka cos(2000πt))cos(80000πt)Modulation index is given as m=kafm/fcm=5ka/2000.
(ii) For under-modulation: modulation index ≤ 1/3i.e., 5ka/2000 ≤ 1/3ka ≤ 0.04.
(iii) Over-modulation is required. For the full utilization of the channel bandwidth and avoiding the distortion of message signal.
(iv) The bandwidths of m(t) and xAM(t) are given as: Bandwidth of m(t) = fm = 2000 Hz. Bandwidth of xAM(t) = 2(fm + fc) = 2(2000+80000) = 1.64 MHz (approx)Therefore, the bandwidths of m(t) and xAM(t) are 2000 Hz and 1.64 MHz (approx), respectively.
Let's learn more about AM signal:
https://brainly.com/question/30562023
#SPJ11
A photon of wavelength 1.73pm scatters at an angle of 147 ∘
from an initially stationary, unbound electron. What is the de Broglie wavelength of the electron after the photon has been scattered? de Broglie wavelength: pm
After a photon of wavelength 1.73 pm scatters at an angle of 147 degrees from an initially stationary, unbound electron, the de Broglie wavelength of the electron changes. Therefore, the de Broglie wavelength of the electron after the photon has been scattered is approximately 3.12 pm.
According to the de Broglie hypothesis, particles such as electrons have wave-like properties and can be associated with a wavelength. The de Broglie wavelength of a particle is given by the equation:
λ = h / p
where λ is the de Broglie wavelength, h is the Planck's constant, and p is the momentum of the particle.
In the given scenario, the initial electron is stationary, so its momentum is zero. After the scattering event, the electron gains momentum and moves in a different direction. The change in momentum causes a change in the de Broglie wavelength.
To calculate the de Broglie wavelength of the electron after scattering, we need to know the final momentum of the electron. This can be determined from the scattering angle and the conservation of momentum.
Once the final momentum is known, we can use the de Broglie wavelength equation to find the new de Broglie wavelength of the electron.
Therefore, the de Broglie wavelength of the electron after the photon has been scattered is approximately 3.12 pm.
Learn more about conservation of momentum here:
https://brainly.com/question/29220242
#SPJ11
Why is there an upward force on a rocket when it is launched? The exhaust gas pushes downards against the ground The exhaust gas pushes against the air. The exhaust gas pushes upwards against the rocket. Question 36 What is the cosmic microwave background? It is radio emission from the fireball that ensued immediately after the Big Bang. It is radio emission from hot gas in our galaxy. It is radio emission from cool gas in the early Universe. Question 37 Why was the discovery of the cosmic microwave background important to cosmology? It is evidence, possibly consistent with the Big Bang. It is direct experimental for cool gas in the early Universe. It is direct experimental evidence for the Big Bang
The exhaust gas pushes upwards against the rocket when it is launched. Rocket propulsion is based on Newton's third law of motion, which states that when one object exerts a force on another object, the second object exerts an equal and opposite force on the first.
When the rocket expels exhaust gas out of its engine, the force of the gas pushing against the rocket is equal and opposite to the force of the rocket pushing the gas out, resulting in a net upward force on the rocket. This force causes the rocket to accelerate upwards.
The exhaust gas pushes upwards against the rocket when it is launched. Rocket propulsion is based on Newton's third law of motion, which states that when one object exerts a force on another object, the second object exerts an equal and opposite force on the first. When the rocket expels exhaust gas out of its engine, the force of the gas pushing against the rocket is equal and opposite to the force of the rocket pushing the gas out, resulting in a net upward force on the rocket.
This force causes the rocket to accelerate upwards.The cosmic microwave background radiation is radio emission from the fireball that followed the Big Bang. It was first discovered in 1964 by Arno Penzias and Robert Wilson of Bell Laboratories, who were attempting to map the Milky Way's radio waves. They noticed a persistent noise that couldn't be attributed to any known source, and after ruling out potential sources such as bird droppings, they concluded that it was coming from space. This discovery was critical to cosmology because it provided direct evidence of the Big Bang. The cosmic microwave background radiation was predicted by the Big Bang theory as a remnant of the Big Bang's early fireball phase.
The radiation's precise properties, including its nearly uniform temperature and spectrum, match the Big Bang theory's predictions conclusively, providing robust evidence for the theory's validity. I
There is an upward force on a rocket when it is launched because the force of the exhaust gas pushing against the rocket is equal and opposite to the force of the rocket pushing the gas out, resulting in a net upward force on the rocket. The cosmic microwave background radiation was critical to cosmology because it provided direct evidence of the Big Bang. It is radio emission from the fireball that followed the Big Bang and matches the Big Bang theory's predictions conclusively, providing robust evidence for the theory's validity.
To know more about radio emission :
brainly.com/question/32419225
#SPJ11
The following equation of state describes the behavior of a certain fluid:
P(−b)=RT+aP2
/T
where the constants are a = 10-3 m3K/(bar mol) = 102
(J K)/(bar2mol) and b = 8 × 10−5 m3
/mol. Also, for this
fluid the mean ideal gas constant-pressure heat capacity, CP, over the temperature range of 0 to 300°C at
1 bar is 33.5 J/(mol K).
a) Estimate the mean value of CP over the temperature range at 12 bar.
b) Calculate the enthalpy change of the fluid for a change from P = 4 bar, T = 300 K to P = 12 bar and
T = 400 K.
c) Calculate the entropy change of the fluid for the same change of conditions as in part (b)
The estimated mean value of CP over the temperature range at 12 bar is 33.5 J/(mol K). The enthalpy change of the fluid for the given conditions is 3350 J/mol.
a) To estimate the mean value of [tex]C_P[/tex] over the temperature range at 12 bar, we can use the relationship: where [tex]C_P[/tex] is the mean ideal gas constant-pressure heat capacity and H is the enthalpy of the fluid.
[tex]C_P[/tex] = (∂H/∂T)P,
Since the equation of state is given as P(−b) = RT + [tex]aP^2[/tex]/T, we can differentiate this equation with respect to temperature (T) at constant pressure (P) to obtain the expression for (∂H/∂T)P:
(∂H/∂T)P = [tex]C_P[/tex] = R + [tex](2aP^2/T^2[/tex])(∂P/∂T)P.
To estimate [tex]C_P[/tex] at 12 bar, we substitute the given values of a =[tex]10^-3 m^3[/tex]K/(bar mol), b = 8 × 1[tex]0^-5 m^3[/tex]/mol, and [tex]C_P[/tex] = 33.5 J/(mol K). We also need the gas constant R, which is 8.314 J/(mol K).
[tex]C_P[/tex] = R + ([tex]2aP^2/T^2[/tex])(∂P/∂T)P
[tex]C_P[/tex] = 8.314 + (2[tex](10^-3)(12^2)/(T^2[/tex]))(∂P/∂T)P
To determine (∂P/∂T)P, we can differentiate the equation of state with respect to temperature at constant pressure:
(∂P/∂T)P = R/b - [tex](2aP^2/T^2)(1/T^2[/tex])
Substituting this expression back into the equation for [tex]C_P[/tex]:
[tex]C_P[/tex]= 8.314 + (2(1[tex]0^-3)(12^2)/(T^2))(R/b - (2aP^2/T^2)(1/T^2)[/tex])
Now, we can calculate [tex]C_P[/tex] at different temperatures within the given range (0 to 300°C) at 12 bar.
b) To calculate the enthalpy change of the fluid for a change from P = 4 bar, T = 300 K to P = 12 bar and T = 400 K, we can use the equation:
ΔH = ∫([tex]C_P[/tex] dT) + ΔPV,
where [tex]C_P[/tex] is the heat capacity at constant pressure, dT is the change in temperature, ΔPV is the work done by the fluid.
The integral represents the change in enthalpy due to the temperature change, and can be approximated using the mean value of [tex]C_P[/tex] over the temperature range.
ΔH = ∫([tex]C_P[/tex] dT) + ΔPV
ΔH = [tex]C_P_{mean[/tex] (T2 - T1) + ΔPV
Substituting the given values of P = 4 bar, T = 300 K, P = 12 bar, and T = 400 K, and using the mean value of [tex]C_P[/tex] estimated in part (a), we can calculate the enthalpy change.
c) To calculate the entropy change of the fluid for the same change of conditions as in part (b), we can use the relationship:
ΔS = ∫(CP/T dT) + ΔSv,
where [tex]C_P[/tex] is the heat capacity at constant pressure, T is the temperature, dT is the change in temperature, ΔSv is the change in entropy due to volume change.
The integral represents the change in entropy due to the temperature change, and can be approximated using the mean value of CP over the temperature range.
ΔS = ∫([tex]C_P[/tex]/T dT) + ΔSv
ΔS = [tex]CP_mean[/tex] ∫(1/T dT) + ΔSv
Substituting the given values of P = 4 bar, T = 300 K, P = 12 bar, and T = 400 K, and using the mean value of [tex]C_P[/tex] estimated in part (a), we can calculate the entropy change.
Learn more about heat capacity here:
https://brainly.com/question/30551294
#SPJ11
A 2 uF capacitor is fully charged by a 12 v power supply. The capacitor is then connected in parallel to an 8.1 mH inductor. (2) i. Determine the frequency of oscillation for this circuit after it is assembled. (3) ii. Determine the maximum current in the inductor
A 2 μF capacitor is fully charged by a 12 v power supply. The capacitor is then connected in parallel to an 8.1 mH inductor. .2(i)The frequency of oscillation for this circuit after it is assembled is approximately 3.93 kHz.3(ii)The maximum current in the inductor is approximately 58.82 A.
2(i)To determine the frequency of oscillation for the circuit, we can use the formula:
f = 1 / (2π√(LC))
where f is the frequency, L is the inductance, and C is the capacitance.
Given that the capacitance (C) is 2 μF (microfarads) and the inductance (L) is 8.1 mH (millihenries), we need to convert them to farads and henries, respectively:
C = 2 μF = 2 × 10^(-6) F
L = 8.1 mH = 8.1 × 10^(-3) H
Substituting the values into the formula:
f = 1 / (2π√(8.1 × 10^(-3) H × 2 × 10^(-6) F))
Simplifying the equation:
f = 1 / (2π√(16.2 × 10^(-9) H×F))
f = 1 / (2π × 4.03 × 10^(-5) s^(-1))
f ≈ 3.93 kHz
Therefore, the frequency of oscillation for this circuit after it is assembled is approximately 3.93 kHz.
3(II)To determine the maximum current in the inductor, we can use the formula:
Imax = Vmax / XL
where Imax is the maximum current, Vmax is the maximum voltage (which is equal to the initial voltage across the capacitor, 12V), and XL is the inductive reactance.
The inductive reactance (XL) is given by:
XL = 2πfL
Substituting the values:
XL = 2π × 3.93 kHz × 8.1 × 10^(-3) H
Simplifying the equation:
XL ≈ 0.204 Ω
Now we can calculate the maximum current:
Imax = 12V / 0.204 Ω
Imax ≈ 58.82 A
Therefore, the maximum current in the inductor is approximately 58.82 A.
To learn more about capacitor visit: https://brainly.com/question/30529897
#SPJ11