The angular acceleration of a 20m long see-saw with an inertia moment of 200kgm, when one end is pushed down with a force of 400N, is 40 [tex]rad/s^2[/tex].
To find the angular acceleration of the see-saw, we can use the formula for torque:
τ = Iα,
where τ represents the torque, I is the inertia moment, and α denotes the angular acceleration. The torque is given by the product of the force applied (F) and the distance from the pivot point (r).
In this case, the force applied is 400N, and the length of the see-saw is 20m. Thus, the torque is calculated as:
τ = F × r = 400N × 20m = 8000 Nm.
Given that the inertia moment of the see-saw is 200kgm, so τ = Iα can be rearranged to find α:
α = τ / I.
Plugging in the values,
α = 8000 Nm / 200kgm = 40 [tex]rad/s^2[/tex].
Therefore, the angular acceleration of the see-saw is 40 [tex]rad/s^2[/tex].
To know more about angular acceleration, visit
https://brainly.com/question/1980605
#SPJ11
someone observed light striking perpendicular to a thin film in air. Since they measured the wavelength of light inside the film. What is the thickness of the film?
a. 5/8 of a wavelength, constructive interference will always occur.
b. one-half of a wavelength, constructive interference will always occur.
c. one-quarter of a wavelength, constructive interference will always occur.
d. one-half of a wavelength, destructive interference will always occur.
The thickness of the film is one-quarter of a wavelength (c).
When light strikes a thin film perpendicularly, a portion of the light is reflected and a portion is transmitted through the film. The reflected and transmitted light waves can interfere with each other, leading to constructive or destructive interference. In the case of constructive interference, the peaks and troughs of the two waves align, resulting in a stronger combined wave. For constructive interference to occur, the path length difference between the reflected and transmitted waves must be an integer multiple of the wavelength.
In this scenario, the observed wavelength of light inside the film is different from the wavelength in air. This indicates that there is a phase change upon reflection from the film's surface. For constructive interference to occur, the path length difference must be equal to one wavelength or an odd multiple of half a wavelength. Since there is a phase change upon reflection, the path length difference corresponds to half the physical thickness of the film.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
A radio station transmits isotropically (ie in all directions) electromagnetic radiation at a frequency of 100.8 MHz. At a certain distance from the radio station the intensity of the wave is I=0.267 W/m^2.
a) What will be the intensity of the wave at a quarter of the distance from the radio station?
b) What is the wavelength of the transmitted signal?
If the power of the antenna is 5 MW.
c) At what distance from the source will the intensity of the wave be 0.134 W/m^2?
d) and what will be the absorption pressure exerted by the wave at that distance?
e) and what will be the effective electric field (rms) exerted by the wave at that distance?
a) The intensity at a quarter of the distance is 1.068 W/[tex]m^2[/tex].
b) The wavelength of the transmitted signal is approximately 2.972 m.
c) tThe distance from the source when the intensity is 0.134 W/[tex]m^2[/tex] is approximately 1183.5 m.
d) The absorption pressure at that distance is approximately 4.47 x [tex]10^{-10}[/tex] Pa.
e) The effective electric field (rms) at that distance is approximately 1.32 x [tex]10^{-4}[/tex] V/m.
To solve the given problems, we need to use the formulas related to electromagnetic waves and their properties.
a) The intensity of a wave is inversely proportional to the square of the distance from the source.
Therefore, if the distance is reduced to a quarter, the intensity will increase by a factor of 4.
Thus, the intensity at a quarter of the distance from the radio station will be 4 times the initial intensity: I = 4 * 0.267 W/[tex]m^2[/tex] = 1.068 W/[tex]m^2[/tex].
b) The wavelength of a wave can be determined using the formula: wavelength = speed of light / frequency.
The speed of light in a vacuum is approximately 3 x 10^8 m/s.
Converting the frequency from MHz to Hz, we have f = 100.8 x 10^6 Hz.
Substituting these values into the formula, we get: wavelength = (3 x 10^8 m/s) / (100.8 x 10^6 Hz) ≈ 2.972 m.
c) To find the distance from the source when the intensity is 0.134 W/[tex]m^2[/tex], we rearrange the formula for intensity and distance: distance = √(power / (4π * intensity)).
Given that the power of the antenna is 5 MW (5 x 10^6 W) and the intensity is 0.134 W/[tex]m^2[/tex], we can calculate the distance: distance = √((5 x 10^6 W) / (4π * 0.134 W/m^2)) ≈ 1183.5 m.
d) The absorption pressure exerted by the wave can be calculated using the formula: pressure = intensity / (speed of light).
Substituting the intensity and the speed of light, we get: pressure = 0.134 W/[tex]m^2[/tex] / (3 x 10^8 m/s) ≈ 4.47 x 10^-10 Pa.
e) The effective electric field (rms) can be determined using the formula: electric field = √(2 * power / (speed of light * area)).
Given that the power is 5 MW, the speed of light is 3 x 10^8 m/s, and assuming the wave is spreading in all directions (isotropic), the area is 4π[tex]r^2[/tex], where r is the distance.
Substituting these values, we have: electric field = √(2 * (5 x 10^6 W) / (3 x 10^8 m/s * (4π * (1183.5 m)^2))) ≈ 1.32 x [tex]10^{-4}[/tex] V/m.
In summary, a) the intensity at a quarter of the distance is 1.068 W/[tex]m^2[/tex], b) the wavelength of the transmitted signal is approximately 2.972 m, c) the distance from the source when the intensity is 0.134 W/[tex]m^2[/tex] is approximately 1183.5 m, d) the absorption pressure at that distance is approximately 4.47 x [tex]10^{-10}[/tex] Pa, and e) the effective electric field (rms) at that distance is approximately 1.32 x [tex]10^{-4}[/tex] V/m.
Learn more about electromagnetic waves here:
https://brainly.com/question/25847009
#SPJ11
An object 25cm away from a lens produces a focused image on a film 15cm away.What is the focal length of the converging lens?
formula for calculating the focal length of a converging lens is:
1/f = 1/v - 1/u
where f is the focal length of the lens, v is the distance between the lens and the image plane (film), and u is the distance between the lens and the object.
In this case, the object is 25 cm away
A wave travelling along a string is described by: y(x,t)=(0.0351 m)sin[(52.3rad/s)x+(2.52rad/s)t] with x in meters and t in seconds. a) What is the wavelength of the wave? b) What is the period of oscillation? c) What is the frequency of the wave?
The frequency of the wave is 8.33 Hz.
The given wave travelling along a string is described by:y(x,t) = (0.0351 m)sin[(52.3rad/s)x + (2.52rad/s)t]Where x is in meters and t is in seconds. To find the wavelength, we use the formula:wavelength (λ) = 2π/kHere, k = (52.3 rad/s), soλ = 2π/kλ = 2π/(52.3 rad/s)λ = 0.120 mTherefore, the wavelength of the wave is 0.120 m.To find the period of oscillation, we use the formula:T = 2π/ωHere, ω = (52.3 rad/s), soT = 2π/ωT = 0.120 sTherefore, the period of oscillation is 0.120 s.To find the frequency of the wave, we use the formula:f = ω/2πHere, ω = (52.3 rad/s), sof = ω/2πf = 8.33 Hz. Therefore, the frequency of the wave is 8.33 Hz.
To know more about wave visit:
https://brainly.com/question/3619541
#SPJ11
3cos(wt/3), where I is in meters and t in seconds. The acceleration of the particle The position of a partide is given by in my when2mis 249 2.1 275 228
The given equation represents the position of a particle as a function of time, given by x(t) = 3cos(wt/3), where x is in meters and t is in seconds. To find the acceleration of the particle, we need to take the second derivative of the position function with respect to time.
The first derivative of x(t) gives us the velocity function v(t):
v(t) = dx(t)/dt = -3w/3 * sin(wt/3)
Differentiating again, we find the second derivative, which is the acceleration function a(t):
a(t) = dv(t)/dt = d²x(t)/dt² = (-3w/3)² * cos(wt/3)
Simplifying further, we get:
a(t) = w² * cos(wt/3)
The acceleration of the particle, a(t), is given by w² times the cosine of wt/3.
In the given context, the values of w, which is the angular frequency, are not provided. Therefore, we cannot determine the specific numerical value of the acceleration. However, we can analyze its behavior based on the equation. The acceleration is directly proportional to w², meaning that increasing the value of w will result in a larger acceleration. Additionally, the cosine function oscillates between -1 and 1, so the acceleration will oscillate between -w² and w².
In summary, the acceleration of the particle is given by the equation a(t) = w² * cos(wt/3). The specific numerical value of the acceleration depends on the value of the angular frequency w, which is not provided in the given information.
Learn more about acceleration here:
https://brainly.com/question/12550364
#SPJ11
The atomic cross sections for 1-MeV photon interactions with carbon and hydrogen are, respectively, 1.27 barns and
0.209 barn.
(a) Calculate the linear attenuation coefficient for paraffin. (Assume the composition CH2 and density 0.89 g/ cm3.)
(b) Calculate the mass attenuation coefficient.
The linear attenuation for paraffin is 0.75cm-1 and the mass attenuation coefficient is 902 cm2/kg. Calculation for both the attenuation is given below in detail.
(a) Linear attenuation coefficient: Linear attenuation coefficient (μ) refers to the attenuation coefficient of a beam or radiation per unit length of material. The linear attenuation coefficient can be determined using the following equation:μ = σ × nwhereσ is the atomic cross section, and n is the number of atoms per unit volume (atoms/cm3). The following formula may be used to calculate the linear attenuation coefficient for paraffin. Linear attenuation coefficient for carbon is given by,μC = σC × nC. The linear attenuation coefficient for hydrogen is given by,μH = σH × nH. The composition of paraffin is CH2, meaning it is made up of one carbon atom, two hydrogen atoms, and two hydrogen atoms. We can thus calculate the number of atoms per unit volume for carbon and hydrogen atoms. We can use the equation below to calculate the linear attenuation coefficient:μ = (μC × wC + μH × wH) where wC and wH are the weights of carbon and hydrogen, respectively. Linear attenuation coefficient for carbon:μC = σC × nCwhereσC = 1.27 barns nC = 2.69 × 1022 atoms/cm3(from the density of paraffin)The weight of carbon in CH2 = 12 g/mole× 1 mole/14 g × (1 g/ cm3) = 0.857 g/cm3wC = 0.857 g/cm3 / (12 g/mole) = 0.0714 moles/cm3The number of carbon atoms in 0.0714 moles = 0.0714 × 6.02 × 1023 atoms/mole= 4.30 × 1022 atoms/cm3Linear attenuation coefficient for carbon:μC = 1.27 barns × 4.30 × 1022 atoms/cm3= 5.47 cm2/g. For hydrogen:μH = σH × nHwhereσH = 0.209 barnsnH = 5.38 × 1022 atoms/cm3(from the density of paraffin)The weight of hydrogen in CH2 = 2 g/mole× 1 mole/14 g × (1 g/ cm3) = 0.143 g/cm3wH = 0.143 g/cm3 / (1 g/mole) = 0.143 moles/cm3. The number of hydrogen atoms in 0.143 moles = 0.143 × 6.02 × 1023 atoms/mole= 8.60 × 1022 atoms/cm3 Linear attenuation coefficient for hydrogen:μH = 0.209 barns × 8.60 × 1022 atoms/cm3= 1.80 cm2/g. The linear attenuation coefficient for paraffin:μ = (μC × wC + μH × wH)= (5.47 cm2/g × 0.0714 moles/cm3) + (1.80 cm2/g × 0.143 moles/cm3)= 0.75 cm-1
(b) Mass attenuation coefficient: Mass attenuation coefficient (μ/ρ) refers to the linear attenuation coefficient of a substance per unit mass of the material. The mass attenuation coefficient can be determined using the following equation:μ/ρ = σ/ρwhereρ is the density of the material. The mass attenuation coefficient of paraffin is obtained using the equation below:μ/ρ = (μC × wC + μH × wH) / ρwhere wC and wH are the weights of carbon and hydrogen, respectively.The density of paraffin is 0.89 g/cm3. The weight of carbon and hydrogen are already known.The mass attenuation coefficient of paraffin:μ/ρ = [(5.47 cm2/g × 0.0714) + (1.80 cm2/g × 0.143)] / 0.89 g/cm3= 0.0902 cm2/g or 902 cm2/kg.
Learn more about attenuation:
https://brainly.com/question/29511209
#SPJ11
While mass is at rest-Turn on displacement x, velocity v and acceleration a vectors. Pull the mass Hive below the movable line so top of the mass is at movable line and release. Set motion to slow. Note the energy graph on left side. Observe how the velocity, acceleration and displacement vectors (nary with position of the mass. Observe how the different forms of energy vary with position of the mass. Assume the oscillation has an amplitude of A. Answer the following: 35 ATAQ air no atniog _d)v=a c) v=-v(max) gniworia vhsals-rigang si no notenimsieb sqoiz 1) For the moving mass, what is the velocity v when x = -A fou v=+v(max) b) v=0 (a) 2)Where is the velocity + and acceleration -? At x=0 b) between x = 0 and x=+A between x =0 and x=-A w asdi Tol avlod) at x = |Allaume) anywhere the mass is moving and accelerating (3)Where is the velocity maximum? a) a) at x = |A|ob worlz bat x =0 4)Where is the kinetic energy maximum ? (a) At equilibrium b) at maximum height er sthW nollsups Con its way down between x =0 and x= -A gos at the lowest point of motion 10115
Therefore, the answer to the question is as follows:a) v=0 (a) 2) between x = 0 and x=+A w asdi Tol avlod) at x = |A|ob worlz bat x =0 4) At equilibrium, the kinetic energy is at a maximum.
The motion of a mass oscillating about a point is analyzed to show how the various types of energy involved in the motion change with the position of the mass. At rest, turn on the displacement x, velocity v, and acceleration a vectors.
Pull the mass Hive beneath the movable line until the top of the mass is on the movable line, then release it. Slow down the movement. Observe how the velocity, acceleration, and displacement vectors relate to the mass's position. Observe how the various types of energy differ with the position of the mass.
Assume that the amplitude of the oscillation is A. 1. The velocity v is zero when x is equal to -A.2. The velocity is positive and the acceleration is negative at x = 0.3. The maximum velocity is at x = 0.4. The kinetic energy is maximum at the maximum height of the oscillation.
Therefore, the answer to the question is as follows:a) v=0 (a) 2) between x = 0 and x=+A w asdi Tol avlod) at x = |A|ob worlz bat x =0 4) At equilibrium, the kinetic energy is at a maximum.
to know more about kinetic
https://brainly.com/question/7694005
#SPJ11
Assume that the lenses in questions 1) and 2) are made of a material with an index of refraction n=1.5 and are submerged in a media with an index of refraction nm=3.0. a) Calculate the radius. Assume both radii are the same. [10 pts] b) What are the focal distances of the converging and the diverging lenses if they are now submerged in a media with an index of refraction nm=3.0? [5 pts] c) Explain why the converging lens became diverging and vice versa in that media. [5 pts] Two lenses with fi=10cm and f2=20cm are placed a distance 25cm apart from each other. A 10cm height object is placed 30cm from the first lens. a) Where is the image through both lenses found and how height is the image? [5 pts] b) For the object in part 4a) above, what are the characteristics of the image, real or virtual, larger, smaller or of the same size, straight up or inverted?
In the given scenario, the lenses have an index of refraction of n = 1.5 and are submerged in a medium with an index of refraction of nm = 3.0. We need to calculate the radius of the lenses, determine the focal distances in the new medium.
And explain why the converging lens becomes diverging and vice versa. Additionally, we have two lenses with focal lengths of 10 cm and 20 cm placed 25 cm apart, and we need to find the position and height of the image formed by both lenses, as well as analyze the characteristics of the image.
a) To calculate the radius of the lenses, we would need additional information or equations specific to the lens shape or design. The question doesn't provide sufficient details to determine the radius.
b) When the lenses are submerged in a medium with an index of refraction of nm = 3.0, the focal distances change. The converging lens, which had a focal length of 10 cm, would now have a shorter focal length due to the increased refractive index. The diverging lens, which had a focal length of 20 cm, would now have a longer focal length. The exact focal distances can be calculated using the lensmaker's formula or the thin lens formula, considering the new refractive index.
c) The change in the refractive index of the surrounding medium affects the behavior of the lenses. The converging lens becomes diverging because the increased refractive index causes the light rays to bend more upon entering the lens, leading to a divergence of the rays. Conversely, the diverging lens becomes converging because the increased refractive index causes the light rays to bend less upon entering the lens, resulting in a convergence of the rays.
d) To determine the position and height of the image formed by the two lenses, we need to apply the lens formula and magnification formula for each lens. The characteristics of the image, such as whether it is real or virtual, larger or smaller, and straight up or inverted, can be determined based on the relative positions of the object and the focal points of the lenses and by analyzing the magnification values. Without specific values for distances and focal lengths, it is not possible to provide precise answers regarding the image characteristics.
Learn more about focal distances here:
https://brainly.com/question/31248476
#SPJ11
The motion of a particle of mass 2 kg connected to a spring is described by x = 10 sin (5 πt). What is the kinetic energy of the particle at time t=1 s? Show your works a. 0 kJ
b. 24.67 kJ c. 3,50 kJ d. 0.79 kJ
e. 0.05 kJ
The kinetic energy of the particle connected to a spring at time t=1 s is option (b) 24.67 kJ.
x= 10sin (5πt)
The velocity of the particle will be given by:
dx/dt = 10cos(5πt) × 5π
Since we are asked to find the kinetic energy of the particle connected to a spring, we know that:
Kinetic energy = 1/2mv²
Where m is the mass of the particle and v is its velocity.
Substituting the values, we get:
Kinetic energy = 1/2 × 2 × (10cos(5πt) × 5π)²= 1/2 × 2 × (10 × 5π)² cos²(5πt)= 1/2 × 2 × (250π²) cos²(5πt)≈ 24.67 kJ (at t = 1s)
Therefore, the correct option is (b) 24.67 kJ.
Learn more about kinetic energy https://brainly.com/question/8101588
#SPJ11
The emitted power from an antenna of a radio station is 10 kW. The intensity of radio waves arriving at your house 5 km away is 31.83 μW m⁻². i. Determine the average energy density of the radio waves at your house. ii. Determine the maximum electric field seen by the antenna in your radio.
The average energy density of the radio waves at your house is 6.37 x 10⁻¹⁴ J m⁻³ and the maximum electric field seen by the antenna in your radio is 1.94 x 10⁻⁴ V m⁻¹.
i. Power emitted by the radio station antenna, P = 10 kW = 10,000 W
The distance from the radio station antenna to the house, r = 5 km = 5000 m
Intensity of radio waves at the house, I = 31.83 μW m⁻² = 31.83 x 10⁻⁶ W m⁻²
Formula:
The average energy density of the radio waves is given by the formula,
ρ = I / (2c)
The maximum electric field at any point due to an electromagnetic wave is given by the formula,
E = (Vm) / c
Where
c = Speed of light in vacuum = 3 x 10⁸ m/s
Substitute the given values in the formula,
ρ = I / (2c)
ρ = (31.83 x 10⁻⁶) / (2 x 3 x 10⁸)
ρ = 6.37 x 10⁻¹⁴ J m⁻³
Thus, the average energy density of the radio waves at your house is 6.37 x 10⁻¹⁴ J m⁻³.
ii. To determine the maximum electric field seen by the antenna in your radio.
Substitute the given values in the formula,
E = (Vm) / c10 kW = (Vm²) / (2 x 377 x 3 x 10⁸)Vm²
= 10 kW x 2 x 377 x 3 x 10⁸Vm²
= 4.52 x 10¹⁵Vm = 2.13 x 10⁸ V
The maximum electric field,
E = (Vm) / c
E = (2.13 x 10⁸) / 3 x 10⁸
E = 1.94 x 10⁻⁴ V m⁻¹
Thus, the maximum electric field seen by the antenna in your radio is 1.94 x 10⁻⁴ V m⁻¹.
Learn more about Electric field:
https://brainly.com/question/19878202
#SPJ11
A wavefunction of a travelling wave is described by its vertical displacement as a function of position and time as follows y(x, t) = 2.5cos (2nt - x) where y and x are in m and t in s. Which of the following is/are correct about the wave? A. B. The period of the travelling wave is 1.0 s. The amplitude of the travelling wave is 2.5 m. The wavelength of the travelling wave is 4.0 m. C.
The time period `T` is `T = 2π/2n = π/n = 3.14 s/ 2s ≈ 1.57 s`. The time period of the wave is approximately 0.5 seconds. Therefore, options A and B are incorrect.
The wavefunction of a traveling wave is described by its vertical displacement as a function of position and time as follows `y(x, t) = 2.5cos (2nt - x)`
where `y` and `x` are in meters, and `t` is in seconds.
The correct options about the wave are as follows:
The amplitude of the travelling wave is 2.5 meters. The wavelength of the travelling wave is 4.0 meters. T
he period of the travelling wave is 0.5 seconds.
Waveform `y(x, t) = 2.5cos (2nt - x)` is an equation of a travelling wave with angular frequency `ω = 2n`.
Its vertical displacement is represented by `y` at a given time `t` and position `x`.
The amplitude of a wave is the maximum displacement of any point on the wave from its undisturbed position. Amplitude is represented by `A`.
Here, the amplitude of the wave is `A = 2.5 meters`.
The wavelength of the wave is the distance over which the shape of the wave repeats itself, usually from crest to crest or from trough to trough. The wavelength is represented by the Greek letter `λ`.Here, `y(x, t) = 2.5cos (2nt - x)` is in the form of `y = Acos(kx - ωt)`, where `k = 2n`, `ω = 2n`, and the phase angle is `φ = 0`.
Thus, the wavelength `λ` is given by:`λ = 2π/k = 2π/2n = π/n = 3.14 m/ 2s ≈ 1.57 m`.
The time period of a wave is the time required for one complete cycle of the wave to pass a given point.
The time period `T` is given by:` T = 2π/ω
`Here, `ω = 2n`,
Therefore `T = 2π/2n = π/n = 3.14 s/ 2s ≈ 1.57 s`. The time period of the wave is approximately 0.5 seconds. Therefore, options A and B are incorrect.
Learn more about wavefunction here:
https://brainly.com/question/29089081
#SPJ11
1.Based on the The Torino Scale diagram below, if the KINETIC ENERGY of a meteor is 10,000,000 MT and the COLLISION PROBABILITY is 1 in 500 then the TORINO SCALE VALUE would be (fill in a number from 0 to 10). and the CONSEQUENCE would be (write in either Global, Regional, Local or No Consequence
2.Based on the The Torino Scale diagram below, if the KINETIC ENERGY of a meteor is 750,000 MT and the COLLISION PROBABILITY is 1 in 100,000,000 then the TORINO SCALE VALUE would be (fill in a number from 0 to 10). and the CONSEQUENCE would be (write in either Global, Regional, Local or No Consequence)
3.Based on the The Torino Scale diagram below, if the KINETIC ENERGY of a meteor is 1000 MT and the COLLISION PROBABILITY is 1 in 90 then the TORINO SCALE VALUE would be (fill in a number from 0 to 10). and the CONSEQUENCE Would be (write in either Global, Regional, Local or No
Consequence).
1. Based on the Torino Scale diagram below, if the kinetic energy of a meteor is 10,000,000 MT and the collision probability is 1 in 500, then the Torino Scale value would be 10. The consequence would be global.
According to the Torino Scale diagram, with a kinetic energy of 10,000,000 MT and a collision probability of 1 in 500, the corresponding Torino Scale value would be 10. This indicates that the impact of the meteor would pose a global threat capable of causing a major catastrophe.
2. Based on the Torino Scale diagram below, if the kinetic energy of a meteor is 750,000 MT and the collision probability is 1 in 100,000,000, then the Torino Scale value would be 0. The consequence would be no consequence.
Referring to the Torino Scale diagram, a meteor with a kinetic energy of 750,000 MT and a collision probability of 1 in 100,000,000 would result in a Torino Scale value of 0. This implies that the impact of the meteor would have no consequence as it is highly likely to burn up in the Earth's atmosphere.
3. Based on the Torino Scale diagram below, if the kinetic energy of a meteor is 1000 MT and the collision probability is 1 in 90, then the Torino Scale value would be 2. The consequence would be local.
Examining the Torino Scale diagram, a meteor with a kinetic energy of 1000 MT and a collision probability of 1 in 90 would correspond to a Torino Scale value of 2. This signifies that the impact of the meteor would be of local significance, causing regional damage.
It's important to mention that without the actual Torino Scale diagram or more specific guidelines, the provided explanations are based on hypothetical scenarios and may not reflect the actual Torino Scale classification system.
Learn more about kinetic energy
https://brainly.com/question/999862
#SPJ11
Look up masses and radii for the following objects and compute their average densities, in grams per cubic centimeter: • The Sun • A red giant with twice the Sun's mass and 100 times its radius • A neutron star with twice the mass of the Sun, but the radius of a city (10 km) HINT: Problem 1 is a straightforward application of the Density formula. Example 1 on the density handout is especially relevant. You can confirm some of your answers in the text. Given that one cubic centimeter is about a teaspoon, how many grams would a teaspoon of neutron star material weigh? Given that there are about 900,000 grams in a ton, how many tons does this teaspoon weigh? Since one cubic centimeter occupies a volume of roughly one teaspoon, you answer for the density of a neutron star tells you exactly how many grams are in one cubic centimeter of neutron star stuff. You should then convert from grams to tons. When deciding whether to multiply or divide, ask yourself; should the number of tons be greater or smaller than the number of grams?
The densities of the objects are as follows:
Sun: 1.41 g/cm^3
Red Giant: 0.0282 g/cm^3
Neutron Star: 949 g/cm^3
Additionally, one teaspoon of neutron star material weighs approximately 0.0053 tons.
The average densities of several objects were calculated based on their masses and radii. The objects considered were the Sun, a red giant with twice the Sun's mass and 100 times its radius, and a neutron star with twice the mass of the Sun but the radius of a city.
The Sun:
Mass: 1.99 × 10^33 grams
Radius: 6.96 × 10^10 centimeters
Volume: (4/3) × π × (6.96 × 10^10)^3 cubic centimeters
Density: Mass/Volume = 1.99 × 10^33 / (4.19 × 10^33) = 1.41 grams per cubic centimeter
Red Giant:
Mass: 3.98 × 10^33 grams (twice the mass of the Sun)
Radius: 6.96 × 10^10 centimeters (100 times the Sun's radius)
Volume: (4/3) × π × (6.96 × 10^10)^3 cubic centimeters
Density: Mass/Volume = 3.98 × 10^33 / (1.41 × 10^35) = 0.0282 grams per cubic centimeter
Neutron Star:
Mass: 3.98 × 10^33 grams (twice the mass of the Sun)
Radius: 10 kilometers = 10^7 centimeters
Volume: (4/3) × π × (10^7)^3 cubic centimeters
Density: Mass/Volume = 3.98 × 10^33 / (4.19 × 10^24) = 949 grams per cubic centimeter
It was determined that one cubic centimeter of neutron star material weighs 949 grams, which is nearly a ton. Since one cubic centimeter occupies a volume of roughly one teaspoon, this tells us exactly how many grams are in one cubic centimeter of neutron star material. To convert grams to tons, considering that there are more grams in one ton, we divide the weight in grams by the conversion factor.
Conversion:
1 ton = 1,000,000 grams
1 teaspoon = 5 cubic centimeters = 5 grams
Therefore, one cubic centimeter of neutron star material weighs 949/5 = 190 grams. Since 1 ton = 1,000,000 grams, one teaspoon of neutron star material would weigh (5/949) tons, which is approximately 0.0053 tons (rounded to four significant figures).
In summary, the densities of the objects are as follows:
Sun: 1.41 g/cm^3
Red Giant: 0.0282 g/cm^3
Neutron Star: 949 g/cm^3
Additionally, one teaspoon of neutron star material weighs approximately 0.0053 tons.
Learn more about densities at: https://brainly.com/question/1354972
#SPJ11
A 19.3x10-6 F capacitor has 89.92 C of charge stored in it. What is the voltage across the capacitor?
Answer:
The voltage across the capacitor is approximately 4,649.74 volts.
To determine the voltage across the capacitor, we can use the formula:
V = Q / C
where V is the voltage,
Q is the charge stored in the capacitor, and
C is the capacitance.
Charge (Q) = 89.92 C
Capacitance (C) = 19.3 x 10^-6 F
Substituting the given values into the formula:
V = 89.92 C / (19.3 x 10^-6 F)
V ≈ 4,649.74 V
Therefore, the voltage across the capacitor is approximately 4,649.74 volts.
Learn more about Voltage here
https://brainly.com/question/30764403
#SPJ11
A string, clamped at both ends, has a mass of 200 g and a length of 12 m. A tension of 55 N is applied, and the string oscillates harmonically. A) (10 points) What is the speed of the waves on the string? B) (10 points) What is the frequency of the 5th harmonic of the oscillating string?
The speed of the waves on the string and the frequency of the 5th harmonic of the oscillating string can be found with the help of the following formulas:
1. Wave speed on the string:
Wave speed = √(T/μ)
where T is the tension in the string and
μ is the linear density of the string.
μ = m/L,
m is the mass of the string and
L is the length of the string.
2. Frequency of nth harmonic:
fn = n(v/2L)
where v is the speed of the wave on the string,
L is the length of the string, and
n is the harmonic number.
A) Using the formula for wave speed on the string, we have:
T = 55 Nm = 200 g = 0.2 kgL = 12 mμ = m/L = 0.2 kg/12 m = 0.01667 kg/m
Wave speed = √(T/μ)
= √(55/0.01667)
= 39.59 m/s
Answer: The speed of the waves on the string is 39.59 m/s.
B) Using the formula for frequency of the nth harmonic, we have:
v = 39.59 m/sL = 12 mn = 5fn = n(v/2L) = 5(39.59/2(12)) = 32.98 Hz
Answer: The frequency of the 5th harmonic of the oscillating string is 32.98 Hz.
Learn more about Wave speed here
https://brainly.com/question/3148541
#SPJ11
What is the time constant? s (b) How long will it take to reduce the voltage on the capacitor to 0.100% of its full value once discharge begins? s (c) If the capacitor is charged to a voltage V 0
through a 133Ω resistance, calculate the time it takes to rise to 0.865V 0
(this is about two time constants). S
Therefore, it takes approximately 26.4 seconds to rise to 0.865V0.
Time ConstantIt is the time required by an electric circuit or system to change its state from an initial state to its final state after an abrupt change in one of its variables. The transient response of the circuit or system is characterized by the time constant.
The formula for the time constant in seconds is given by the product of the resistance and the capacitance, i.e.,T=RC(a) To determine the time it takes for the capacitor to discharge to 0.100% of its full value after discharge begins.
Given, V=100% and V'=0.100%It is known that the equation for the capacitor voltage with time during discharge is given by;V = V0e-t/RCSubstituting for the final and initial voltages we have,0.100% V0 = V0e-t/RC
Taking the natural logarithm of both sides,ln(0.001) = -t/RCln(0.001) = -t/1.2 x 10^3 x 2.2 x 10^-6t = 31.2 seconds (to the nearest whole number)Therefore, it will take approximately 31.2 seconds to reduce the voltage on the capacitor to 0.100% of its full value once discharge begins.
(c) If the capacitor is charged to a voltage V0 through a 133Ω resistance, calculate the time it takes to rise to 0.865V0 (this is about two time constants).It is known that the equation for the capacitor voltage with time during charging is given by;V = V0(1 - e-t/RC)
We are required to find the time it takes for the voltage across the capacitor to rise to 0.865V0, which is equivalent to a voltage difference of 0.135V0 from the initial voltage.
Therefore, substituting for the final and initial voltages we have,0.865V0 = V0(1 - e-2T/RC)Rearranging,1 - 0.865 = e-2T/RCln(0.135) = -2T/RCt = 2T = 2 x 1.2 x 10^3 x 2.2 x 10^-6 x ln(0.135)t = 26.4 seconds (to the nearest whole number) Therefore, it takes approximately 26.4 seconds to rise to 0.865V0.
to know more about electric
https://brainly.com/question/2969220
#SPJ11
Frogs have changed their coloring over time to adapt to their environment. This is an example of which of the following?
Adaptation
Artificial selection
Environmental change
Natural selection
Correct option is D. Natural selection.
Frogs have changed their coloring over time to adapt to their environment. This is an example of natural selection.
Natural selection is the process of adaptation in response to environmental change.
The process involves differential survival and reproduction of individuals with genetic traits that are better suited to their environment, and this process can lead to changes in the genetic makeup of a population over time.
As a result, populations of organisms can become better adapted to their environment, which is a critical factor in their survival and continued evolution.
Frogs are known for their remarkable ability to change color to match their surroundings.
This adaptation allows them to blend in with their environment, making them less visible to predators and prey.
The process by which frogs have adapted to their environment is an excellent example of natural selection in action.
Over time, the individuals with genetic traits that provide better camouflage are more likely to survive and reproduce, passing on their traits to their offspring.
As a result, the population of frogs becomes better adapted to their environment, allowing them to thrive in their natural habitats.
The correct Option is D. Natural selection.
For more questions on environment
https://brainly.com/question/1186120
#SPJ8
A gamma-ray telescope intercepts a pulse of gamma radiation from a magnetar, a type of star with a spectacularly large magnetic field. The pulse lasts 0.15 s and delivers 7.5×10⁻⁶ J of energy perpendicularly to the 93-m² surface area of the telescope's detector. The magnetar is thought to be 4.22×10²⁰ m (about 45000 light-years) from earth, and to have a radius of 8.5×10³ m. Find the magnitude of the rms magnetic field of the gamma-ray pulse at the surface of the magnetar, assuming that the pulse radiates uniformly outward in all directions. (Assume a year is 365.25 days.) Number ___________ Units _______________
A pulse of gamma radiation from a magnetar delivers 7.5×10⁻⁶ J of energy perpendicularly to a 93-m² detector. The magnitude of the rms magnetic field of the pulse at the surface of the magnetar is 2.6 x 10^14 T.
The energy delivered by the pulse of gamma radiation is given by E = 7.5×10⁻⁶ J.
The surface area of the detector is A = 93 m².
The duration of the pulse is t = 0.15 s.
The distance from the magnetar to Earth is d = 4.22×10²⁰ m.
The radius of the magnetar is R = 8.5×10³ m.
The speed of light is c = 2.998×10⁸ m/s.
The energy per unit area received by the detector from the pulse is given by the equation:
E/A = (c/4πd²)B²t
where B is the rms magnetic field of the gamma-ray pulse.
Solving for B, we get:
B = sqrt((E/A)/(c/4πd²t)) = sqrt((7.5×10⁻⁶ J / 93 m²)/((2.998×10⁸ m/s)/(4π(4.22×10²⁰ m)²(0.15 s))))
The magnitude of the rms magnetic field of the gamma-ray pulse at the surface of the magnetar is:
B = 2.6 x 10^14 T
where T stands for tesla, the unit of magnetic field.
To know more about magnetic field, visit:
brainly.com/question/14848188
#SPJ11
Gamma rays (-rays) are high-energy photons. In a certain nuclear reaction, a -ray of energy 0.769 MeV (million electronvolts) is produced. Compute the frequency of such a photon.
Hz
Gamma rays (-rays) are high-energy photons. In a certain nuclear reaction, a -ray of energy 0.769 MeV (million electronvolts) is produced ,the frequency of the gamma ray is 1.17 × 10^21 Hz
The frequency of a photon is inversely proportional to its energy. So, if we know the energy of the photon, we can calculate its frequency using the following equation:
frequency = energy / Planck's constant
The energy of the photon is 0.769 MeV, and Planck's constant is 6.626 × 10^-34 J s. So, the frequency of the photon is:
frequency = 0.769 MeV / 6.626 * 10^-34 J s = 1.17 × 10^21 Hz
Therefore, the frequency of the gamma ray is 1.17 × 10^21 Hz.
To learn more about Gamma rays visit: https://brainly.com/question/2399890
#SPJ11
magnetic field (wider than 10 cm ) with a strength of 0.5 T pointing into the page. Finally it leaves the field. While entering the field what is the direction of the induced current as seen from above the plane of the page? clockwise counterclockwise zero While in the middle of the field what is the direction of the induced current as seen from above the plane of the page? clockwise counterclockwise zero While leaving the field what is the direction of the induced current as seen from above the plane of the page? clockwise counterclockwise zero
When a conductor enters a magnetic field, the direction of the induced current can be determined using Fleming's right-hand rule. As seen from above the plane of the page, the direction of the induced current while entering the field is counterclockwise. While in the middle of the field, the induced current is zero, and while leaving the field, the direction of the induced current is clockwise.
Fleming's right-hand rule is a way to determine the direction of the induced current in a conductor when it is moving in a magnetic field. According to this rule, if the thumb of the right hand points in the direction of the motion of the conductor, and the fingers point in the direction of the magnetic field, then the direction in which the palm faces represents the direction of the induced current.
When the conductor enters the magnetic field, the motion of the conductor is from left to right (as seen from above the plane of the page), and the magnetic field is pointing into the page. Using Fleming's right-hand rule, if we point the thumb of the right hand in the direction of the motion (left to right) and the fingers into the page (opposite to the magnetic field), the palm will face counterclockwise. Therefore, the direction of the induced current while entering the field is counterclockwise.
While in the middle of the field, the conductor is moving parallel to the magnetic field, resulting in no change in the magnetic flux through the conductor. Therefore, there is no induced current during this phase.
When the conductor leaves the magnetic field, the motion of the conductor is from right to left (as seen from above the plane of the page), and the magnetic field is pointing into the page. Applying Fleming's right-hand rule, if we point the thumb in the direction of the motion (right to left) and the fingers into the page (opposite to the magnetic field), the palm will face clockwise. Hence, the direction of the induced current while leaving the field is clockwise.
Learn more about conductor here:
https://brainly.com/question/14405035
#SPJ11
A fisherman noticed that a wave strikes the boat side every 5 seconds. The distance between two consecutive crests is 1.5 m. What is the period and frequency of the wave? What is the wave speed?
What is the wave speed if the period is 7.0 seconds and the wavelength is 2.1 m?
What is the wavelength of a wave traveling with a speed of 6.0 m/s and the frequency of 3.0 Hz?
The period of the wave is the time interval between two consecutive crests, while the frequency of a wave is the number of crests that pass a point in a unit time. Hence, we can find the period and frequency using the given information.
Distance between two consecutive crests is 1.5m.
A wave strikes the boat side every 5 seconds.
a) Period and frequency of the wave
The period is the time interval between two consecutive crests. We are given that the wave strikes the boat side every 5 seconds. Hence, the period of the wave is T=5s.The frequency of the wave is the number of crests that pass a point in a unit time. The time taken to complete one wave is the period, T. Hence, the number of crests that pass a point in 1 second is the reciprocal of T.
Therefore, the frequency of the wave is:
f=1/T=1/5=0.2Hz
b) The wave speed
We can use the formula to find the wave speed,
v=fλ
where, v = wave speed, f = frequency and λ = wavelength.
Substituting f = 0.2Hz and λ = 1.5m, we getv=0.2×1.5v=0.3m/s
c) The wavelength of a wave traveling with a speed of 6.0 m/s and the frequency of 3.0 Hz
We can use the formula, v = fλ to find the wavelength.
Rearranging this equation, we get:
λ=v/f=6/3=2m
Hence, the wavelength of the wave is 2m.
Learn more about frequency of wave here
https://brainly.com/question/9373543
#SPJ11
What is the character of a typical stellar spectra? That of pure thermal emission. That of a spectral line absoprtion. That of a thermal emitter with superposed spectral absorption lines. Question 33
A typical stellar spectra character is that of a thermal emitter with superposed spectral absorption lines. This is because a star's surface radiates thermal energy as a result of its high temperatures.
However, gases in the star's outer layers absorb this thermal energy and result in the star's spectrum being dark at specific wavelengths, creating absorption lines. Therefore, a stellar spectrum is not that of pure thermal emission or spectral line absorption. Instead, it is the spectrum of a thermal emitter with superposed spectral absorption lines. option C - That of a thermal emitter with superposed spectral absorption lines.
Stellar spectra, also known as stellar spectra lines, are the wavelengths of electromagnetic radiation emitted by a star. A typical stellar spectra character is that of a thermal emitter with superposed spectral absorption lines. This is because a star's surface radiates thermal energy as a result of its high temperatures. However, gases in the star's outer layers absorb this thermal energy and result in the star's spectrum being dark at specific wavelengths, creating absorption lines. Therefore, a stellar spectrum is not that of pure thermal emission or spectral line absorption. Instead, it is the spectrum of a thermal emitter with superposed spectral absorption lines. A star's spectral lines can provide astronomers with valuable information about the star, such as its temperature, chemical composition, and mass. By examining a star's spectral lines, astronomers can determine the presence and abundance of elements within a star. This information can be used to help determine a star's age, its place in the evolution of stars, and its potential to host planets that may support life.
A typical stellar spectra character is that of a thermal emitter with superposed spectral absorption lines. Stellar spectra provide valuable information about the star's temperature, chemical composition, and mass. By examining these spectra, astronomers can learn about the star's age, its place in the evolution of stars, and its potential to host planets that may support life.
To know more about temperatures visit:
brainly.com/question/11464844
#SPJ11
A truck is driving along the highway behind a tractor when it pulls out to pass. If the truck's acceleration is uniform at 2.3 m/s² for 3.2 s and it reaches a speed of 31 m/s, what was its speed when it first pulled out to pass the tractor? 1) 45 m/s 2) 38 m/s 3) 31 m/s 4) 24 m/s 5) 17 m/s
A tube 1.2 m long is closed at one end. A stretched wire is placed near the open end. The wire is 0.3 m long and has a mass of 5 g. It is fixed at both ends and oscillates in its fundamental mode. By resonance, it sets the air in the tube into oscillation at fourth harmonic frequency. Determine that frequency f and the tension in the wire. Given that the speed of sound in air is 343 m/s. (10 marks)
(b) A stationary detector measures the frequency of a sound source that first moves at constant velocity directly towards the detector and then directly away from it. The emitted frequency is . During the approach the detected frequency is ′pp and during the recession it is ′c. If ′ pp − ′ c = 2, calculate the speed of the source . Given that the speed of sound in air is 343 m/s.
(a) The tension in the wire is approximately 51.01 N.
(a) To determine the frequency and tension, we can use the formula for the frequency of a stretched wire in its fundamental mode:
f = (1/2L) * √(T/μ)
where:
f is the frequency of the wire,
L is the length of the wire,
T is the tension in the wire, and
μ is the linear mass density of the wire.
Given:
Length of the wire (L) = 0.3 m
Mass of the wire (m) = 5 g = 0.005 kg
Speed of sound in air (v) = 343 m/s
Length of the tube (tube length) = 1.2 m
To determine the tension (T) in the wire, we need to calculate the linear mass density (μ) first:
μ = m/L
μ = 0.005 kg / 0.3 m
μ = 0.0167 kg/m
Now, we can calculate the frequency (f) of the wire:
f = (1/2L) * √(T/μ)
Since the wire sets the air in the tube into oscillation at the fourth harmonic frequency, we know that the frequency of the wire is four times the fundamental frequency of the air in the tube:
f = 4 * (v/4L)
Substituting the given values:
f = 4 * (343/4*1.2)
f = 4 * (343/4.8)
f ≈ 285.42 Hz
Therefore, the frequency of the wire is approximately 285.42 Hz.
To determine the tension (T) in the wire, we rearrange the formula:
T = (μ * f² * L²) * 4
Substituting the given values:
T = (0.0167 * (285.42)² * (0.3)²) * 4
T ≈ 51.01 N
Therefore, the tension in the wire is approximately 51.01 N.
(b) Let's denote the emitted frequency as f_e, the detected frequency during approach as f_pp, and the detected frequency during recession as f_c.
According to the Doppler effect, the detected frequency can be expressed as:
[tex]f_{pp} = (v + v_s) / (v + v_d) * f_e\\f_c = (v - v_s) / (v + v_d) * f_e[/tex]
where:
[tex]v_s[/tex] is the speed of the source,
[tex]v_d[/tex] is the speed of the detector, and
v is the speed of sound in air (343 m/s).
Given:
[tex]f_{pp} - f_c = 2[/tex]
Substituting the expressions for [tex]f_{pp[/tex] and [tex]f_c[/tex]
[tex](v + v_s) / (v + v_d) * f_e - (v - v_s) / (v + v_d) * f_e = 2[/tex]
Simplifying the equation:
[tex][(v + v_s) - (v - v_s)] / (v + v_d) * f_e = 2\\[2v_s / (v + v_d)] * f_e = 2[/tex]
Simplifying further:
[tex]v_s / (v + v_d) * f_e = 1\\v_s = (v + v_d) / f_e[/tex]
Substituting the given value for the speed of sound in air:
[tex]v_s = (343 + v_d) / f_e[/tex]
Since the detected frequency during approach is [tex]f_{pp} = f_e + 'pp[/tex] and the detected frequency during recession is [tex]f_c[/tex] = [tex]f_e[/tex] - ′c, we can rewrite the given equation as:
([tex]f_e[/tex] + ′pp) - ([tex]f_e[/tex] - ′c) = 2
Simplifying:
2[tex]f_e[/tex] + ′pp - ′c = 2
2[tex]f_e[/tex] = 2 - (′pp - ′c)
[tex]f_e[/tex] = 1 - (′pp - ′c) / 2
Substituting this expression back into the equation for [tex]v_s[/tex]
[tex]v_s[/tex] = (343 + [tex]v_d[/tex] ) / [1 - (′pp - ′c) / 2]
Now, we can solve for the speed of the source ( [tex]v_s[/tex]) by rearranging the equation:
[tex]v_s[/tex] = (343 + [tex]v_d[/tex]) / [1 - (′pp - ′c) / 2]
[tex]v_s[/tex] = (343 + [tex]v_d[/tex]) / [2 - (′pp - ′c) / 2]
[tex]v_s[/tex] = (343 + [tex]v_d[/tex]) * 2 / [4 - (′pp - ′c)]
Therefore, the speed of the source can be calculated using the above equation, with the given values of [tex]v_d[/tex], ′pp, and ′c.
To learn more about tension visit:
brainly.com/question/15211735
#SPJ11
A virtual image of an object formed by a converging lens is 2.33mm tall and located 7.28cm before the lens. The magnification of the lens is 2.16. Determine the focal length of the lens (in cm).
A virtual image of an object formed by a converging lens is 2.33mm tall and located 7.28cm before the lens. Therefore, the focal length of the converging lens is -8.514 cm.
Given that virtual image of an object formed by a converging lens is 2.33 mm tall and located 7.28 cm before the lens and the magnification of the lens is 2.16.
To determine the focal length of the lens (in cm).Formula used: magnification = -image height/object height magnification = v/u
where, v = distance of image from the lens, u = distance of object from the lens
Using the above formula, we can determine the distance of image from the lens as:u = -v/magnification , v = u x magnificationGiven that,object height, h0 = 0.00233 m
image height, hi = 0.00233 mm x 10^-3 = 2.33 x 10^-6 m , distance of the object from the lens, u = -7.28 cm = -0.0728 m, distance of the image from the lens, v = ?magnification, m = 2.16Putting these values in the formula above: v = u x magnification
v = -0.0728 x 2.16v = -0.156768 m
We know the formula for the focal length is given as:1/f = 1/v - 1/uwhere,f = focal length of the lens
Putting the values in this formula,1/f = 1/-0.156768 - 1/-0.0728Solving for f,f = -0.08514 m = -8.514 cm
Therefore, the focal length of the converging lens is -8.514 cm.
Learn more about focal length here:
https://brainly.com/question/11870211
#SPJ11
A tank was initially filled with 100 gal of salt solution containing 1 lb of salt per gallon. Fresh brine containing 2 lbs of salt/gal runs into the tank at a rate of 5 gal/min, and the mixture, assumed uniform, runs out at the same rate. At what time will the concentration of the salt in the tank become? Select one: O a. 55 min O b. 28 min O c. 32 min O d. 14 min
The concentration of salt in the tank will become 2 lbs/gal after 14 minutes. Hence, the correct option is (d) 14 min.
The initial volume of the tank = 100 galInitial salt concentration = 1 lb/gal.Salt solution = 100 × 1 = 100 lbs.Initially, we have a total of 100 lbs of salt in the tank.Let us assume that after t minutes, the concentration of salt in the tank will become x.Now, we need to write a differential equation for this mixture. The amount of salt in the mixture is equal to the amount of salt that flows in minus the amount of salt that flows out.dA/dt = (C1 × V1 - C2 × V2) /V.
Where, A = amount of salt in the mixture.C1 = initial salt concentration = 1 lb/gal.C2 = salt concentration in incoming brine = 2 lb/gal.V1 = volume of salt solution in the tank at any time = (100 + 5t) galV2 = volume of incoming brine = 5 galV = volume of the mixture at any time = (100 + 5t) gal.dA/dt = (1 × (100 + 5t) - 2 × 5)/ (100 + 5t) ... (1)On simplifying the above equation, we getdA/dt = (100 - 5t)/ (100 + 5t) ... (2)Separating variables and integrating, we get∫ (100 + 5t) / (100 - 5t) dt = ∫ dA / A∫ (100 + 5t) / (100 - 5t) dt = ln |A| + C... (3)On integrating (3), we get-10 ln |100 - 5t| = ln |A| + C (solving for constant).
Therefore,-10 ln |100 - 5t| = ln |100| + C... (4)When t = 0, the salt concentration is 1 lb/gal. So,100 lbs of salt and 100 gallons of solution are there in the tank.Therefore,100 = V × 1 => V = 100 gallonsSubstitute this in equation (4).-10 ln |100 - 5t| = ln |100| + ln |A| (simplifying C = ln |A|)ln |100 - 5t|^(-10) = ln (100 × |A|)... (5)ln |100 - 5t| = -ln (100 × |A|)^(1/10)ln |100 - 5t| = -ln (|A|)^(1/10) × ln (100)^(1/10)ln |100 - 5t| = -0.5 ln |A| ... (6)Let the salt concentration becomes 2 lb/gal after time t.So, we need to find the value of t such that x = 2 lb/gal.
The amount of salt in the mixture at any time A = V × xA = (100 + 5t) × 2A = 200 + 10tOn substituting A = 200 + 10t and x = 2 in equation (6), we getln |100 - 5t| = -0.5 ln (200 + 10t)... (7)Solving for t in equation (7)100 - 5t = (200 + 10t)^(-0.5)100 - 5t = (2 + t)^(-1)100 - 5t = 1 / (2 + t)t = 14 minutes (approx)Therefore, the concentration of salt in the tank will become 2 lbs/gal after 14 minutes. Hence, the correct option is (d) 14 min.
Learn more about equation here,
https://brainly.com/question/29174899
#SPJ11
3. The total mechanical energy of the object at the highest point compared to its
total mechanical energy at the lowest point is
A. lesser
B. greater
C. equal
D. not related.
The total mechanical energy of the object at the highest point compared to its total mechanical energy at the lowest point is lesser. The correct answer is option A.
The total mechanical energy of an object is the sum of its potential and kinetic energy. When an object moves, it experiences changes in potential and kinetic energy. In simple terms, the total mechanical energy of an object is the energy that it possesses due to its position or motion. In general, when an object moves from its highest to the lowest point, its potential energy is at its maximum value while its kinetic energy is at its minimum value. At the highest point, the object has maximum potential energy and zero kinetic energy. At this point, the total mechanical energy of the object is equal to its potential energy. On the other hand, at the lowest point, the object has maximum kinetic energy and minimum potential energy. At this point, the total mechanical energy of the object is equal to its kinetic energy.Since the total mechanical energy at the highest point is equal to the potential energy only while the total mechanical energy at the lowest point is equal to the kinetic energy only, it is clear that the total mechanical energy at the highest point is lesser than the total mechanical energy at the lowest point. Therefore, the answer to the question is A.For more questions on mechanical energy
https://brainly.com/question/28154924
#SPJ8
A small object begins a free-fall from a height of 25.0 m. After 1.40 s, a second small object is launched vertically upward from the ground with an initial velocity of 37.0 m/s. At what height h above the ground will the two objects first meet? h = ________ m
A small object begins a free-fall from a height of 25.0 m. After 1.40 s, a second small object is launched vertically upward from the ground with an initial velocity of 37.0 m/s.
Height from which first object falls, s₁ = 25.0 m Time elapsed, t = 1.40 s Initial velocity of second object, u₂ = 37.0 m/s
For the first object that undergoes free-fall;
The vertical displacement after time t, s₁ = u₁t + 1/2 gt² -------> (1)
Where u₁ = Initial velocity of the object, g = acceleration due to gravity = 9.81 m/s²
For the second object,
The vertical displacement after time t, s₂ = u₂t - 1/2 gt² ------> (2)
Substitute the given values in the above equations and solve for t
Using equation (1),s₁ = u₁t + 1/2 gt² = 0 + 1/2 x 9.81 x (1.40)² = 12.99 m
Thus, the first object falls a distance of 12.99 m in 1.40 seconds.Now, using equation (2),s₂ = u₂t - 1/2 gt²
Solve the above equation for t
Substitute the values u₂ = 37.0 m/s t = Time at which the two objects meet g = 9.81 m/s²∴ t = s₂/g = (u₂t - s₁)/g
On substituting the given values we get, t = (37.0 x 1.40 - 12.99) / 9.81= 3.59 s
Now, the height at which the two objects will first meet is given by the equation, s = s₁ + u₁t Where u₁ = 0 m/s (as it is in free-fall)
Substituting the values we get, s = 25.0 + 0 x 3.59= 25.0 m
Therefore, the height at which the two objects will first meet is 25.0 m.
Here's another question on free-fall: https://brainly.com/question/14460830
#SPJ11
A proton is launched with a speed of 3.20×10 6
m/s perpendicular to a uniform magnetic field of 0.310 T in the positive z direction. (a) What is the radius of the circular orbit of the proton? cm (b) What is the frequency of the circular movement of the proton in this field?
The answer is a) the radius of the circular orbit of the proton is approximately 6.72 cm. and b) the frequency of the circular movement of the proton in this field is 7.59 x [tex]10^4[/tex] Hz.
When a proton is launched with a speed of 3.20 x [tex]10^6[/tex] m/s perpendicular to a uniform magnetic field of 0.310 T in the positive z direction, circular motion occurs due to the magnetic force acting on the proton. It is a consequence of the Lorentz force experienced by the particle, which acts as a centripetal force on the proton as it travels through the magnetic field.
Part (a): In a circular motion, the magnetic force acting on the proton is given by F = qvB, where F is the magnetic force, q is the charge of the proton, v is the velocity of the proton and B is the magnetic field.
The force acting on the proton creates a centripetal acceleration given by a = [tex]v^2/r.[/tex]
Here, r is the radius of the circular orbit of the proton, which is given by: r = mv/qB where m is the mass of the proton.
Substituting the given values in the above expression, r = [(1.673 x [tex]10^-27[/tex]kg)(3.20 x[tex]10^6 m/s[/tex])]/[(1.602 x[tex]10^-19 C[/tex])(0.310 T)] = 0.0672 m = 6.72 cm (approximately)
Therefore, the radius of the circular orbit of the proton is approximately 6.72 cm.
Part (b): The frequency of the circular movement of the proton in this field is given by f = v/2πr, where v is the velocity of the proton and r is the radius of the circular orbit.
Substituting the given values in the above expression, f = (3.20 x [tex]10^6[/tex]m/s)/[2π(0.0672 m)] = 7.59 x [tex]10^4[/tex] Hz
Therefore, the frequency of the circular movement of the proton in this field is 7.59 x [tex]10^4[/tex] Hz.
know more about magnetic force
https://brainly.com/question/30532541
#SPJ11
An initially uncharged capacitor is coenected to a battery and remains connected until it reaches equilibrium. Once in equilibrium, what is the voltage across the capacitor? Assume ideal wires. O equal to the potential difference of the battery O larger than the potential difference across the battery O smaller than the potential difference of the battery
Once connected to a battery until reaching equilibrium, an initially uncharged capacitor will have a voltage across it that is equal to the potential difference of the battery.
A capacitor is a device that stores electrical energy in an electric field. Capacitors are utilized in electronic circuits to store electric charge temporarily. Capacitors are devices that store charge and energy in the form of an electric field created between two conductors separated by an insulating material called the dielectric.
When voltage is applied to a capacitor, electric charges accumulate on the conductors of the capacitor due to the separation of the plates. The potential difference between the plates rises as more charge is stored on the conductors. When the capacitor is fully charged, the voltage across it equals the voltage of the battery because the current flowing through the circuit is zero.
A capacitor's voltage is determined by the amount of charge that is stored on its plates. A capacitor's voltage will be equal to the potential difference of the battery once equilibrium is reached. This is because the flow of current in the circuit will stop when equilibrium is reached, and the capacitor will be fully charged. Therefore, the voltage across the capacitor will be equal to the potential difference of the battery.
Learn more about capacitor: https://brainly.com/question/30529897
#SPJ11