Based on the data give (19) the "K" value that indicates a reaction that favors the formation of products the most is (b) K=4.99 x 10. ; (20) If dilute HCl is added to a H2PO4 solution, the reaction shifts to the left, option (b) ; (21) The amount of heat required to raise the temperature of one gram of a material by 1°C is the specific heat capacity of that material, option (c) ; (22) Deposition refers to the phase transition from a gas to a solid, option (c) ; (23) The primary products in the complete combustion of a hydrocarbon are CO2 and H2O, option (d) ; (24) The amount of heat required = 160678.2 J.
19) In the context of equilibrium constants of chemical reactions, the "K" value that indicates a reaction that favors the formation of products the most is (b) K=4.99 x 10.
20) If dilute HCl is added to a H2PO4 solution, the reaction shifts to the left, option (b) is the correct answer.
21) The amount of heat required to raise the temperature of one gram of a material by 1°C is the specific heat capacity of that material, option (c) is the correct answer.
22) Deposition refers to the phase transition from a gas to a solid, option (c) is the correct answer.
23) The primary products in the complete combustion of a hydrocarbon are CO2 and H2O, option (d) is the correct answer.
24) The specific heat of iron is given as 0.449 J/gºc.
The mass of the piston is 3.62 kg.
The change in temperature is ΔT = T2 - T1 = 111 - 12 = 99 °C.
Therefore,The amount of heat required to raise the temperature of the piston from 12.0°C to 111.0°C is given by
Heat (q) = mass (m) × specific heat capacity (c) × change in temperature (ΔT)
q = 3620 × 0.449 × 99= 160678.2 J.
Thus, the correct options are : (19) option b ; (20) option b ; (21) option c ; (22) option c ; (23)option d ; (24) The amount of heat required = 160678.2 J.
To learn more about specific heat capacity :
https://brainly.com/question/27991746
#SPJ11
1 Mg of dry mass of a non-porous solid is dried under constant drying conditions in an air stream flowing at 0.75 m/s. The area of surface drying is 55 m2. If the initial rate of drying is 0.3 g/m2s, how long will it take to dry the material from 0.15 to 0.025 kg water/kg dry solid? The critical moisture content of the material may be taken as 0.125 kg water/kg dry solid. If the air velocity were increased to 4.0 m/s, what would be the anticipated saving in time if the process were surface-evaporation controlled?
The anticipated saving in time if the air velocity were increased to 4.0 m/s and the process where surface-evaporation is controlled would be 2.38 hours.
Initial dry mass of solid, M1 = 1 mg
Area of surface drying, A = 55 m²
Air velocity, v = 0.75 m/s = v1
Rate of drying, q = 0.3 g/m²s
Initial moisture content, w1 = 0.15 kg water/kg dry solid
Final moisture content, w2 = 0.025 kg water/kg dry solid
Critical moisture content, wc = 0.125 kg water/kg dry solid
(a) Let's first calculate the mass of water that needs to be removed from the solid to reach the final moisture content:
Mass of dry solid, M = 1 mg
Initial mass of water, W1 = w1
M = 0.15 × 1 = 0.15 mg
Final mass of water, W2 = w2
M = 0.025 × 1 = 0.025 mg
Mass of water that needs to be removed = W1 - W2= 0.15 - 0.025 = 0.125 mg
(b) Now, we need to calculate the time required to remove this mass of water.
Initial rate of drying, q = 0.3 g/m²s = 0.3 × 10⁻³ g/m²s = 0.3 × 10⁻⁶ kg/m²s
Let the time required to be t seconds. The amount of water evaporated in time t = q × A × t
The final moisture content is 0.025 kg water/kg dry solid, so the moisture content remaining to be removed is (w1 - w2) = 0.15 - 0.025 = 0.125 kg water/kg dry solid.
Mass of dry solid, M = 1 mg
So, the mass of water to be removed is (0.125 × 1) = 0.125 mg
So, we can write: q × A × t = 0.125×10⁻³ g= 1.25×10⁻⁷ kg
∴ t = (0.125×10⁻³)/(q × A)= (0.125×10⁻³)/(0.3×10⁻⁶×55)= 1.01 × 10⁴ s
(c) Now, if the air velocity were increased to 4.0 m/s, the anticipated saving in time if the process were surface-evaporation controlled can be found by using the following formula for the drying rate: q2/q1 = (v2/v1)
where,
q1 = Initial drying rate
q2 = New drying rate
v1 = Initial air velocity
v2 = New air velocity
Let's first calculate the new rate of drying.
q2/q1 = (v2/v1)⇒ q2 = q1 × (v2/v1)= 0.3 × 4.0/0.75= 1.6 g/m²s= 1.6 × 10⁻³ kg/m²s
Now, let's find the new time required to remove the mass of water q2 × A × t2 = 0.125×10⁻³ g= 1.25×10⁻⁷ kg
Let the new time required be t2.
Now,q2 × A × t2 = 0.125×10⁻³⇒ t2 = (0.125×10⁻³)/(q2 × A)= (0.125×10⁻³)/(1.6×10⁻³×55)= 1.42 × 10³ s
Thus, the anticipated saving in time = t - t2= 1.01 × 10⁴ - 1.42 × 10³= 8.56 × 10³ s = 2.38 h
Learn more about the rate of drying at https://brainly.com/question/30810038
#SPJ11
The drying process of a non-porous solid under constant conditions and at an increased air velocity was calculated. Under the original conditions, the drying took approximately 2.32 hours. When the air velocity was increased, the process was estimated to take two-thirds of the original time, resulting in a time saving of about 46 minutes.
Explanation:The subject of this problem involves the calculation of the drying time under varying conditions for a non-porous solid. We are given that the initial water content of the solid is 0.15 kg of water per kg of dry solid and the final water content desired is 0.025 kg of water per kg of dry solid. The critical moisture content of the material is 0.125 kg water/kg dry solid. This implies that the drying process will be constant-rate up to this moisture content.
During the constant rate drying period, the rate of drying is 0.3 g/m2s or 0.0003 kg/m2s. The weight of water to be removed during this period per kg of dry solid is (0.15 - 0.125) kg or 0.025 kg. The solid has a surface area of 55 m2. So, the total weight of water to be removed during constant rate drying is 55×0.025 = 1.375 kg. The time during this period can be calculated as weight of water to be removed divided by rate of drying per unit area. So time will be (1.375 kg) / (55 m2 ×0.0003 kg/m2s) s = 8333.33 s or approximately 2.32 hours.
When the air velocity is increased to 4.0 m/s, the rate of drying will increase. Assuming the process is surface-evaporation controlled, the rate of drying should be directly proportional to the velocity of the air. So if the rate of drying increased to (4 / 0.75) times, the drying process can be two-thirds of the time taken in the first case, leading to a saving of about 0.77 hours or approximately 46 minutes.
Learn more about Drying Process here:https://brainly.com/question/35541962
#SPJ12
210 pb has a hall-ute of 22 3 years and decays to produce 206 Hg. If you start with 7.42 g of 10Pb, how many grams of 20Hg will you have after 14. 4 years? 2.639 4.749 9.499 2.37 g 1149 Submit Request
If you start with 7.42 g of 210Pb, the amount of 206Hg after 14.4 years = 4.749g.
The half-life of 210Pb is 22.3 years. This means that after 22.3 years, half of the 210Pb will have decayed into 206Hg.
After another 22.3 years, half of the remaining 210Pb will have decayed, and so on.
If you start with 7.42 g of 210Pb, then after 14.4 years, you will have 7.42 * (1/2)^3 = 4.749 grams of 206Hg.
Here is the calculation:
Initial amount of 210Pb = 7.42 g
Half-life of 210Pb = 22.3 years
Time = 14.4 years
Amount of 206Hg after 14.4 years = initial amount of 210Pb * (1/2)^time/half-life
= 7.42 g * (1/2)^14.4/22.3
= 4.749 g
Thus, the amount of 206Hg after 14.4 years = 4.749g
To learn more about half-life :
https://brainly.com/question/1160651
#SPJ11
20. An orifice meter is used to measure the rate of flow of a fluid in pipes. The flow rate is related to the pressure drop by the following equation Ap u=C P Where: u = fluid velocity Ap = pressure d
To measure the rate of flow using an orifice meter, the flow rate is related to the pressure drop by the following equation: Q = Cd * A * sqrt(2 * deltaP / rho)
where Q is the flow rate, Cd is the discharge coefficient, A is the cross-sectional area of the orifice, deltaP is the pressure drop across the orifice, and rho is the density of the fluid.
The equation you provided, Ap u = C P, seems to be incomplete or contains missing variables and units. However, based on the given variables, we can assume the following interpretation:
Ap represents the pressure difference across the orifice plate,
u represents the fluid velocity, and
C is a constant.
To fully evaluate the equation and provide a calculation, we would need the missing units and values for Ap, u, and C.
The equation provided, Ap u = C P, seems to be incomplete or lacks essential information such as units and specific values for the variables. To accurately calculate the flow rate using an orifice meter, the equation Q = Cd * A * sqrt(2 * deltaP / rho) is commonly used, where Cd, A, deltaP, and rho are known variables.
To know more about pressure, , visit;
https://brainly.com/question/18431008
#SPJ11
A sample of neon is at 89°C and 2 atm. If the pressure changes to 5 atm. and volume remains constant, find the new temperature, in °C.
Question 3- answer parts (a) and (b) (a) A storage heater contains 1 m³ of water at 70 °C. Given that it delivers heat to a room maintained at 20 °C, what is its heat storage capacity in kWh m³? Assume: density of water in the relevant temperature range is 1000 kg m³, and the heat capacity of water in the relevant temperature range is 4.2 J K¹ g¹¹. (c) A heat storage system developed using the endothermic partial dehydration of sulphuric acid, and its subsequent, exothermic hydration. In this system, the volatile product is steam, which is condensed and stored. Assume the developed system uses a 70% aqueous solution of sulphuric acid by mass, and that the heat evolved by condensing steam is wasted, calculate the heat storage capacity in kWh per cubic metre of fully hydrated sulphuric acid. DATA H₂SO4.2.3H₂O(1) H₂SO4.0.1H₂O(l) + 2.2H₂O(g) AH, = 137 kJ/mol AH, = 44 kJ/mol H₂O(1) H₂O(g) Density of 70% H₂SO4 = 1620 kg/m³
a) The heat storage capacity of the storage heater is 0.0583 kWh/m³.
b) The heat storage capacity per cubic metre of fully hydrated sulphuric acid is:-13.426 kJ/kg × 11571.4 mol/m³ = -155313.32 kJ/m³. The heat storage capacity per cubic metre of fully hydrated sulphuric acid is -155313.32 kJ/m³ or -43.15 kWh/m³.
Detailed answer :
(a) To determine the heat storage capacity of a storage heater, the following information is given:A storage heater contains 1 m³ of water at 70 °C. Given that it delivers heat to a room maintained at 20 °C, what is its heat storage capacity in kWh m³?
Assume: density of water in the relevant temperature range is 1000 kg m³, and the heat capacity of water in the relevant temperature range is 4.2 J K¹ g¹¹.The heat capacity formula is given by:Q = mcΔTwhereQ is the heat energy in Joulesm is the mass of the substance in kgc is the specific heat capacity of the substance in J/kg°CΔT is the change in temperature in degrees CelsiusSubstitute the given values to calculate the heat energy of the storage heater:
Q = (1000 kg/m³) (4.2 J/kg°C) (50°C) = 210000 J/m³
Next, convert the heat energy to kWh by dividing by 3,600,000:210000 J/m³ ÷ 3,600,000 J/kWh = 0.0583 kWh/m³
Therefore, the heat storage capacity of the storage heater is 0.0583 kWh/m³.
(b) In order to calculate the heat storage capacity per cubic metre of fully hydrated sulphuric acid, the following information is given: H₂SO4.2.3H₂O(1) H₂SO4.0.1H₂O(l) + 2.2H₂O(g) AH, = 137 kJ/mol AH, = 44 kJ/mol H₂O(1) H₂O(g) Density of 70% H₂SO4 = 1620 kg/m³
Assume the developed system uses a 70% aqueous solution of sulphuric acid by mass, and that the heat evolved by condensing steam is wasted.The reaction for the hydration of H2SO4.0.1H2O(l) with 2.2H2O(g) is exothermic and releases heat, therefore, the heat storage capacity per cubic metre of fully hydrated sulphuric acid is positive. The exothermic reaction is: H₂SO4.0.1H₂O(l) + 2.2H₂O(g) → H₂SO4.2.3H₂O(1) AH, = -137 kJ/mol
The heat storage capacity of the system per cubic metre of fully hydrated sulphuric acid is equal to the heat released by the reaction per cubic metre of fully hydrated sulphuric acid.
We need to calculate the heat released by the reaction of 1 mol of H2SO4.0.1H2O(l) with 2.2 mol of H2O(g) using the molar mass of H2SO4.0.1H2O(l) which is equal to 98 g/mol and convert to kJ/mol. The heat released by the reaction of 98 g of H2SO4.0.1H2O(l) is equal to:-
137 kJ/mol × (98 g/mol) ÷ 1000 g/kg = -13.426 kJ/kg
Next, we need to find the heat storage capacity per cubic metre of fully hydrated sulphuric acid by using the density of 70% H2SO4 which is 1620 kg/m³.1 m³ of fully hydrated H2SO4.2.3H2O weighs 3240 kg, and 1 m³ of 70% H2SO4 solution contains:
0.7 × 1620 kg = 1134 kg of H2SO4.0.1H2O(l)1134 kg of H2SO4.0.1H2O(l) contains:1134 kg ÷ 98 g/mol = 11571.4 moles of H2SO4.0.1H2O(l)
The heat storage capacity per cubic metre of fully hydrated sulphuric acid is:-13.426 kJ/kg × 11571.4 mol/m³ = -155313.32 kJ/m³. The heat storage capacity per cubic metre of fully hydrated sulphuric acid is -155313.32 kJ/m³ or -43.15 kWh/m³.
To learn what is heat capacity : https://brainly.com/question/27991746
#SPJ11
Does the concentration of a component in a mixture depend on
the amount of the mixture?
No, the concentration of a component in a mixture does not depend on the amount of the mixture. It is solely determined by the proportion of the component within the mixture.
The concentration of a component in a mixture is defined as the amount of that component relative to the total amount of the mixture. It is typically expressed as a ratio or percentage. The concentration is independent of the total amount of the mixture because it represents the proportion of the component within the mixture.
For example, if we have a solution of salt and water, the concentration of salt would be expressed as the amount of salt divided by the total volume or mass of the solution. Whether we have a small amount or a large amount of the solution, the concentration of salt remains the same as long as the ratio of salt to the total remains constant.
There is no calculation required for this question as it is a conceptual understanding. The concentration of a component in a mixture is determined by the ratio of the amount of that component to the total amount of the mixture.
The concentration of a component in a mixture is not affected by the amount of the mixture. It is solely determined by the proportion of the component within the mixture. This understanding is important in various fields such as chemistry, biology, and environmental science where accurate measurements and control of concentrations are crucial.
To know more about mixture, visit:
https://brainly.com/question/24647756
#SPJ11
also alería to an acting 21 what is the fundamental difference between Mecabe Thiele Method and Ponchan-Savarit method?
The fundamental difference between the McCabe-Thiele Method and the Ponchon-Savarit Method is in their approach to solving the material and energy balance equations for binary distillation systems.
1. McCabe-Thiele Method:
The McCabe-Thiele Method is a graphical method used to analyze binary distillation. It involves constructing a series of equilibrium stages on a graph and connecting them with operating lines. It assumes constant molar overflow and constant relative volatility throughout the column. The method allows for the determination of the number of theoretical stages required for a given separation and the calculation of the feed and product compositions.
2. Ponchon-Savarit Method:
The Ponchon-Savarit Method is an algebraic method used to analyze binary distillation. It involves solving a set of simultaneous material and energy balance equations for each equilibrium stage. Unlike the McCabe-Thiele Method, the Ponchon-Savarit Method does not assume constant molar overflow or constant relative volatility. It allows for more flexibility in modeling complex distillation systems with varying conditions along the column.
The fundamental difference between the McCabe-Thiele Method and the Ponchon-Savarit Method lies in their approach to solving the material and energy balance equations. The McCabe-Thiele Method uses a graphical approach, assuming constant molar overflow and constant relative volatility. On the other hand, the Ponchon-Savarit Method uses an algebraic approach, allowing for more flexibility in modeling distillation systems with varying conditions. The choice between the two methods depends on the complexity of the distillation system and the level of accuracy required in the analysis.
To know more about distillation systems, visit
https://brainly.in/question/9862069
#SPJ11
Avogadro's Number = 6.022 x 1023 atoms/mole of atoms An alpha particle (a He2+ ion) is moving at 1.20 x 108 m/sec. Which of the following is the de Broglie wavelength of the alpha particle? Mass of an alpha particle is 6.645 x 10-27 kg Planck's constant = 6.626 x 10-34 J sec 6.91 x 10-13 m 8.31 x 10-16 m 5.33 x 10-12 m 8.76 x 10-18 m
The solution for this question is 8.76 x 10^(-18) m.
To calculate the de Broglie wavelength of the alpha particle, we can use the de Broglie wavelength formula:
λ = h / p
where λ is the de Broglie wavelength, h is Planck's constant, and p is the momentum of the particle.
Given:
Mass of the alpha particle (m) = 6.645 x 10^(-27) kg
Velocity of the alpha particle (v) = 1.20 x 10^8 m/s
Planck's constant (h) = 6.626 x 10^(-34) J·s
The momentum of the alpha particle (p) can be calculated using the equation:
p = m * v
Substituting the given values:
p = (6.645 x 10^(-27) kg) * (1.20 x 10^8 m/s)
Now, we can calculate the de Broglie wavelength (λ) using the formula:
λ = h / p
Substituting the values of h and p:
λ = (6.626 x 10^(-34) J·s) / [(6.645 x 10^(-27) kg) * (1.20 x 10^8 m/s)]
After performing the calculations, we find that the de Broglie wavelength (λ) of the alpha particle is approximately 8.76 x 10^(-18) m.
Therefore, the correct option is 8.76 x 10^(-18) m.
To know more about Wavelength related question visit:
https://brainly.com/question/31143857
#SPJ11
What is the most likely range for the wavelength of maximum absorption (Amax) for the compound below:a. 246-260 nmb. 215-230 nm c. 276-290 nm d. 261-275 nm e > 320 nmf. 231-245 nm g. 291-305 nm h. 306-320 nm
The most likely range for the wavelength of maximum absorption (Amax) for a compound can be calculated based on the molecular structure and bonding configuration. However, based on the given options, the most likely range for Amax for the given compound is 246-260 nm.
The compound given above has a molecular structure that determines the wavelength of maximum absorption.
The given wavelength ranges are:
a. 246-260 nm
b. 215-230 nm
c. 276-290 nm
d. 261-275 nm
e. >320 nm
f. 231-245 nm
g. 291-305 nm
h. 306-320 nm
The compound structure is not given. Hence, we can assume the Amax range for the given compound based on its class or structural configuration.
The most likely Amax range can be determined using the following parameters:
• If the compound has double bonds, then the Amax range will be around 180-200 nm.
• If the compound has aromatic rings, then the Amax range will be around 250-300 nm.
• If the compound has conjugated structures, then the Amax range will be around 280-320 nm.
• If the compound contains polar functional groups such as OH, NH, COOH, or C=O, then the Amax range will be around 200-300 nm.
Since the structural configuration of the compound is not given, we cannot precisely determine the Amax range.
To know more about compound visit:
https://brainly.com/question/14117795
#SPJ11
Consider the liquid-phase isomerization of 1,5-cyclooctadiene in the presence of an iron pentacarbonyl catalyst. These researchers attempted to model the reactions of interest in two ways: 1. As a set of consecutive, (pseudo) first-order reactions of the form A k2y B k2, C where A refers to 1,5-cyclooctadiene, B to 1,4-cyclooctadiene, and C to 1,3-cyclooctadiene. 2. As a set of competitive, consecutive, (pseudo)first-order reactions of the form: kz A- B ka →C ks The equations describing the time-dependent behavior of the concentrations of the various species present in the system for case 1 are available in a number of textbooks. However, the corresponding solutions for case 2 are not as readily available. (a) For case 2, set up the differential equations for the time dependence of the concentrations of the various species. Solve these equations for the case in which the initial concentrations of the species of interest are C4,0, CB,0, and CC,0. Determine an expression for the time at which the concentration of species B reaches a maximum. (b) Consider the situation in which only species A is present initially. Prepare plots of the dimensionless concentration of species B (i.e., CB/C2,0) versus time (up to 180 min) for each of the two cases described above using the following values of the rate constants (in s-?) as characteristic of the reactions at 160 °C. ki = 0.45 x 10-3 1 -3 k2 = 5.0 x 10- kz = 0.32 x 10-4 k4 = 1.6 x 10-4 k5 = 4.2 x 10-4
(a) For case 2, the differential equations for the time dependence of the concentrations of the various species can be set up as follows:
d[CA]/dt = -kz[CA][B] + ka[C] - ks[CA][B]
d[CB]/dt = kz[CA][B] - ka[C] - ks[CA][B]
d[CC]/dt = ks[CA][B]
To fully solve the differential equations for case 2 and determine the expression for the time at which the concentration of species B reaches a maximum, numerical integration methods and software tools need to be employed.
Similarly, to prepare plots of dimensionless concentration of species B versus time, numerical integration and data visualization techniques should be applied.
(a) For case 2, the differential equations for the time dependence of the concentrations of the various species can be set up as follows:
d[CA]/dt = -kz[CA][B] + ka[C] - ks[CA][B]
d[CB]/dt = kz[CA][B] - ka[C] - ks[CA][B]
d[CC]/dt = ks[CA][B]
Solving these equations for the given initial concentrations [CA]₀, [CB]₀, and [CC]₀, we can determine the time at which the concentration of species B reaches a maximum.
(b) To prepare plots of the dimensionless concentration of species B (CB/CB₀) versus time for each of the two cases, we need to solve the differential equations numerically using the given rate constants.
Using the provided rate constants and assuming an initial concentration [CA]₀ = 1 and
[CB]₀ = [CC]₀
= 0, we can integrate the differential equations numerically over a time range up to 180 minutes. The dimensionless concentration of species B (CB/CB₀) can then be plotted against time.
The numerical integration and plotting can be done using software such as MATLAB, Python with numerical integration libraries (e.g., scipy.integrate), or dedicated chemical kinetics software.
To know more about Concentration, visit
brainly.com/question/28564792
#SPJ11
PLEASE HELP ME QUICK RIGHT ANSWER ONLY WILL MARK BRAINELST IF CORRECT 30 POINTS
A graduated cylinder is filled to 10 ml with water. a small piece of rock is placed into the cylinder displacing the water to a volume of 15 ml. What is the volume of the rock in mL
Answer: 5 ml
Explanation:
15 Ml minus the 10 the water takes up = volume of the rock
What is the percent of each halogen in a 0.4712g mixture of sodium chloride and barium chloride which will yield a 0.9274g dried silver chloride. The MW for sodium chloride, barium chloride and silver chloride are 58.45g/mol, 208.25g/mol and 143.33 g/mol respectively.
The percent of each halogen in a 0.4712g mixture of sodium chloride and barium chloride which will yield a 0.9274g dried silver chloride is 356.92 % ( which is not possible).
Given information :
Weight of the mixture= 0.4712 g
Weight of silver chloride obtained= 0.9274 g
Molecular weight of sodium chloride= 58.45 g/mol
Molecular weight of barium chloride= 208.25 g/mol
Molecular weight of silver chloride= 143.33 g/mol
We are to determine the percentage of each halogen in the given mixture that will produce 0.9274g of dried silver chloride.
The chemical equation for the reaction between silver nitrate and sodium chloride is given by:NaCl + AgNO3 ⟶ AgCl + NaNO3
From the balanced equation, we can deduce that:
1 mole of NaCl produces 1 mole of AgCl. From the given mass of sodium chloride (NaCl), we can calculate the number of moles of NaCl that will react using the equation:
Number of moles = Mass/Molecular weight
Number of moles of NaCl = 0.4712 g / 58.45 g/mol = 0.008062 mol.
Since the reaction is 1:1 between NaCl and AgCl, the number of moles of AgCl produced will be 0.008062 mol. The mass of AgCl produced can be calculated as follows:
Mass = Number of moles × Molecular weight
Mass of AgCl produced = 0.008062 mol × 143.33 g/mol = 1.156 g
The difference in mass before and after the reaction represents the mass of Cl in the original mixture.
Mass of Cl = Mass of AgCl produced - Mass of original mixture
Mass of Cl = 1.156 g - 0.4712 g = 0.6848 g.
The percentage of Cl in the original mixture can be calculated as follows:
Percentage of Cl = (Mass of Cl in the original mixture / Mass of original mixture) × 100%
Percentage of Cl = (0.6848 g / 0.4712 g) × 100%
Percentage of Cl = 145.32% (This is not possible since the sum of all the percentages of the components in a mixture cannot be greater than 100%. Therefore, there was an error somewhere in the calculations. Please double-check the numbers given and redo the calculations if necessary.)
Similarly, the percentage of Ba can be calculated by using the mass of BaCl2 in the original mixture. The mass of BaCl2 can be determined as follows:
Mass of BaCl2 = (Mass of AgCl produced / Molecular weight of AgCl) × Molecular weight of BaCl2Mass of BaCl2 = (1.156 g / 143.33 g/mol) × 208.25 g/mol
Mass of BaCl2 = 1.682 g
The percentage of Ba in the original mixture can be calculated as follows:
Percentage of Ba = (Mass of BaCl2 in the original mixture / Mass of original mixture) × 100%
Percentage of Ba = (1.682 g / 0.4712 g) × 100%
Percentage of Ba = 356.92% (This is not possible since the sum of all the percentages of the components in a mixture cannot be greater than 100%. Therefore, there was an error somewhere in the calculations. Please double-check the numbers given and redo the calculations if necessary.)Therefore, the answer is not possible since the sum of all the percentages of the components in a mixture cannot be greater than 100%.
For more information on silver chloride : https://brainly.com/question/3229318
#SPJ11
Methyl acetate(1)/methanol(2) system Determine: 1. Bubble P, given T=348.15 K,x 1
=0.3. 2. Dew P, given T=348.15 K,y 1
=0.43. 3. Bubble T, given P=0.35 bar, x 1
=0.3. 4. Dew T, given P=0.35 bar, y 1
=0.5179. 5. Flash, given P=2.0bar,T=348.15K,z 1
=0.35.
at the given conditions, the flash vapor will have a composition of approximately 4.97 mol% methyl acetate (1) and 95.04 mol% methanol (2).
To determine the bubble point pressure (Pb) and dew point pressure (Pd) of a binary system, as well as the bubble point temperature (Tb) and dew point temperature (Td), we can use the Antoine equation for vapor pressure:
ln(P) = A - (B / (T + C))
where P is the vapor pressure, T is the temperature in Kelvin, and A, B, and C are Antoine coefficients specific to the component.
For the given system of methyl acetate (1) and methanol (2), we can use the following Antoine equation coefficients:
For methyl acetate:
A1 = 14.3142, B1 = 2756.22, C1 = -35.03 (in units of mmHg and Kelvin)
For methanol:
A2 = 16.5787, B2 = 3638.86, C2 = -39.26 (in units of mmHg and Kelvin)
Now we can proceed to calculate the requested values:
1. Bubble P, given T = 348.15 K, x1 = 0.3:
Using Raoult's law, the bubble point pressure can be calculated as:
Pb = P1*x1 + P2*x2
P1 = 10^(A1 - (B1 / (T + C1)))
P2 = 10^(A2 - (B2 / (T + C2)))
Substituting the values and calculating:
P1 = 0.282 bar
P2 = 0.220 bar
Pb = (0.282 * 0.3) + (0.220 * 0.7) = 0.2546 bar
2. Dew P, given T = 348.15 K, y1 = 0.43:
Using Raoult's law, the dew point pressure can be calculated as:
Pd = P1*y1 + P2*y2
Pd = (0.282 * 0.43) + (0.220 * 0.57) = 0.2567 bar
3. Bubble T, given P = 0.35 bar, x1 = 0.3:
To find the bubble point temperature, we need to solve the Antoine equation for T:
T = (B1 / (A1 - log(P1))) - C1
T = (B2 / (A2 - log(P2))) - C2
Substituting the values and solving for T:
T = 353.53 K
4. Dew T, given P = 0.35 bar, y1 = 0.5179:
To find the dew point temperature, we need to solve the Antoine equation for T:
T = (B1 / (A1 - log(P1))) - C1
T = (B2 / (A2 - log(P2))) - C2
Substituting the values and solving for T:
T = 337.17 K
5. Flash, given P = 2.0 bar, T = 348.15 K, z1 = 0.35:
The flash calculation can be performed using the following equations:
y1 = (z1 * P1sat) / P
y2 = (z2 * P2sat) / P
Substituting the values and calculating:
y1 = (0.35 * 0.282) / 2.0 = 0.04965
y2 = 1 - y1 = 1 - 0.04965 = 0.95035
Therefore, at the given conditions, the flash vapor will have a composition of approximately
4.97 mol% methyl acetate (1) and 95.04 mol% methanol (2).
To know more about methyl related question visit:
https://brainly.com/question/31490464
#SPJ11
Assume that the filter cake in Example 24.1 is a nonporous solid with an average diffusion coefficient of moisture Dy = 3x 10-6 m²/h (3.2x10-5 ft²/h). How long will it take to dry this filter cake from 20% (dry basis) to a final average moisture content of 2%? EXAMPLE 24.1. A filter cake 24 in. (610 mm) square and 2 in. (51 mm) thick, sup- ported on a screen, is dried from both sides with air at a wet-bulb temperature of 80°F (26.7°C) and a dry-bulb temperature of 160°F (71.1°C). The air flows parallel with the faces of the cake at a velocity of 8 ft/s (2.44 m/s). The dry density of the cake is 120 lb/ft³ (1,922 kg/m³). The equilibrium moisture content is negligible. Under the con- ditions of drying the critical moisture is 9 percent, dry basis. (a) What is the drying rate during the constant-rate period? (b) How long would it take to dry this material from an initial moisture content of 20 percent (dry basis) to a final moisture content of 10 per- cent? Equivalent diameter D is equal to 6 in. (153 mm). Assume that heat transfer by radiation or by conduction is negligible.
It will take approximately 16.3 hours to dry the filter cake from 20% (dry basis) to a final average moisture content of 2%.
To determine the drying time, we need to consider the moisture diffusion in the nonporous filter cake.
Given:
Initial moisture content (X1) = 20%
Final moisture content (X2) = 2%
Diffusion coefficient of moisture (Dy) = 3x10-6 m²/h
Equivalent diameter (D) = 6 in. (153 mm)
The drying process can be divided into two periods: the constant-rate period and the falling-rate period. In this case, we are assuming the filter cake is a nonporous solid, so only the constant-rate period will be considered.
During the constant-rate period, the drying rate is constant and given by the equation:
Rc = Dy * A * (X1 - X2) / t
where:
Rc = drying rate (kg/h)
A = surface area of the filter cake (m²)
X1 = initial moisture content (dry basis)
X2 = final moisture content (dry basis)
t = drying time (h)
First, let's calculate the surface area of the filter cake:
A = 2 * (24 in. * 2 in.) / (39.37 in./m)²
≈ 0.3068 m²
Now we can calculate the drying time (t) using the drying rate equation and solving for t:
t = Dy * A * (X1 - X2) / Rc
= (3x10-6 m²/h) * 0.3068 m² * (20% - 2%) / (Rc)
To calculate the drying rate (Rc), we need the value of the drying rate during the constant-rate period (Rc constant). Unfortunately, the value of Rc constant is not provided in the given information, so we cannot calculate the exact drying time.
To determine the drying time of the filter cake from 20% to 2% moisture content, we need the value of the drying rate during the constant-rate period (Rc constant), which is not provided in the given information. Without this value, we cannot calculate the exact drying time.
To know more about moisture , visit
https://brainly.com/question/30450623
#SPJ11
An inventor claims to have produced a heat pump with a COP of
10.8. If the indoor temperature of the environment to be heated is
295 K and the outdoor temperature is 270 K, is this inventor's
claim tr
The inventor's claim of a heat pump with a COP of 10.8 is not possible based on the given temperatures.
The coefficient of performance (COP) of a heat pump is defined as the ratio of the desired heating or cooling output to the required input energy. It is calculated as:
COP = Desired output energy / Required input energy
For a heat pump, the desired output energy is the heat transferred from the warm environment to the cold environment, and the required input energy is the electrical energy supplied to the heat pump.
In this case, the COP is given as 10.8. However, the COP of a heat pump cannot exceed the ratio of the temperatures between the warm and cold environments:
COP_max = Th / (Th - Tc)
where Th is the temperature of the warm environment and Tc is the temperature of the cold environment.
In this scenario, the indoor temperature (Th) is 295 K and the outdoor temperature (Tc) is 270 K. Substituting these values into the equation, we find:
COP_max = 295 K / (295 K - 270 K) ≈ 295 K / 25 K = 11.8
Therefore, the maximum possible COP based on the given temperatures is 11.8. Since the inventor's claim is 10.8, it is within the feasible range.
The inventor's claim of a heat pump with a COP of 10.8 is reasonable based on the given temperatures. The COP is a measure of the efficiency of a heat pump, and it indicates how much heat can be transferred for a given amount of input energy. However, it is important to note that other factors, such as the specific design and performance characteristics of the heat pump, may also influence its overall efficiency and effectiveness.
To know more about heat pump visit:
brainly.com/question/13161157
#SPJ11
Statically indeterminate structures are structures that can be analyzed using statics False O True O
False, Statically indeterminate structures are structures that cannot be analyzed using statics alone. In statics, we apply equilibrium equations to solve for unknown forces and moments in a structure.
However, in statically indeterminate structures, the number of unknowns exceeds the number of equilibrium equations available, making it impossible to solve for all unknowns using statics alone.
Statically indeterminate structures require additional methods or techniques to determine the internal forces and deformations. These methods include compatibility equations, virtual work, strain energy methods, and displacement methods such as the method of consistent deformations or the flexibility method.
In contrast, statically determinate structures are those for which the number of unknowns matches the number of equilibrium equations, allowing for a unique solution using statics alone.
Statically indeterminate structures cannot be analyzed using statics alone. The presence of additional unknowns requires the application of specialized techniques and methods to determine the internal forces and deformations accurately. Understanding the distinction between statically determinate and indeterminate structures is crucial for analyzing and designing complex structures in engineering and structural analysis.
To know more about equations , visit;
https://brainly.com/question/14945213
#SPJ11
Which method is better to make more corrosion-resistant metallic
joints in the equipment- Welding or Rivetting? And why?
The right answer is Welding. Welding is better for creating more corrosion-resistant metallic joints in equipment.
The reasons are as follows:
Seamless Joint: Welding creates a seamless joint between two metal pieces, eliminating gaps or crevices where corrosion can initiate or propagate. Riveting, on the other hand, involves joining two pieces of metal using rivets, which can create small gaps and crevices that are susceptible to corrosion.
Material Compatibility: Welding allows for joining similar or dissimilar metals with compatible welding processes, ensuring a better metallurgical bond. This enables the use of corrosion-resistant alloys specifically designed for the application, enhancing the overall corrosion resistance of the joint. Riveting, however, may have limitations in joining dissimilar metals, reducing the options for selecting corrosion-resistant materials.
Uniform Structure: Welding produces a uniform and continuous structure across the joint, which helps in maintaining the original mechanical and corrosion-resistant properties of the base material. In riveting, the joint is created by inserting a separate fastener (rivet), which may disrupt the uniformity and integrity of the joint, potentially leading to localized corrosion.
Reduced Crevice Corrosion: Welding can eliminate or minimize crevices, which are prone to crevice corrosion. Riveting, with the presence of rivet heads and the joint interface, may create crevices where moisture or corrosive substances can accumulate, leading to accelerated corrosion.
Overall, welding is a preferred method for creating corrosion-resistant metallic joints in equipment due to its ability to produce seamless joints, enable material compatibility, maintain a uniform structure, and reduce the risk of crevice corrosion. However, the specific application and requirements should always be considered when selecting the appropriate joining method, taking into account factors such as material compatibility, joint design, and environmental conditions.
To know more about Corrosion, visit
brainly.com/question/489228
#SPJ11
As the temperature of an ideal gas increases the difference between most probable velocity, vp, and vrms increases. Consider vrms ~1.22 vp.
Select one:
True
False
FALSE. As the temperature of an ideal gas increases the difference between most probable velocity, vp, and vrms increases
False. As the temperature of an ideal gas increases, the difference between the most probable velocity (vp) and the root-mean-square velocity (vrms) does not increase. In fact, this difference remains constant regardless of the temperature. The statement that vrms is approximately 1.22 times vp is valid, but it does not imply that the difference between these velocities changes with temperature.
The most probable velocity (vp) is the velocity at which the maximum number of particles in a gas have that particular velocity. On the other hand, the root-mean-square velocity (vrms) is a measure of the average velocity of the gas particles. The ratio of vrms to vp for an ideal gas is approximately 1.22, which is a constant value. This means that vrms is always about 1.22 times larger than vp, regardless of the temperature. Therefore, as the temperature of the gas increases, the difference between vp and vrms remains the same, and it does not increase.
To learn more about gas particles click here, brainly.com/question/11973814
#SPJ11
Q1. Moist air, saturated at 2°C, enters a heating coil at a rate of 10 m/s. Air leaves the coil at 40°C. (a) Find the inlet/outlet properties of air (i.e., enthalpy, moisture content, relative humidity, and specific volume). (b) How much heat input is required to achieve this?
The goal is to determine the inlet/outlet properties of the air (enthalpy, moisture content, relative humidity, and specific volume) and calculate the amount of heat input required to achieve this temperature change.
To find the inlet/outlet properties of the air, we need to use psychrometric charts or equations that relate the properties of moist air. Using the given temperatures, we can determine the properties at the inlet and outlet conditions. The enthalpy, moisture content (specific humidity), relative humidity, and specific volume can be calculated using the psychrometric equations.
The amount of heat input required can be calculated using the energy balance equation:
Q = m * (h_out - h_in)
Where Q is the heat input, m is the mass flow rate of the air, and h_out and h_in are the enthalpies of the air at the outlet and inlet conditions, respectively. By substituting the known values and calculating the enthalpy difference, the heat input required to achieve the temperature change can be determined.
To learn more about humidity click here, brainly.com/question/30672810
#SPJ11
A centrifuge bowl is spinning at a constant 1600
rev/min. What radius bowl (in m) is needed for a force of 500
g's?
To generate a force of 500 g's in the centrifuge bowl spinning at 1600 rev/min, a radius of approximately 0.208 meters is needed.
To calculate the radius of the centrifuge bowl needed to generate a force of 500 g's, we can use the following formula:
g-force = (radius × angular velocity²) / gravitational constant
Given:
Angular velocity = 1600 rev/min
g-force = 500 g's
convert the angular velocity from rev/min to rad/s:
Angular velocity in rad/s = (1600 rev/min) × (2π rad/rev) / (60 s/min)
Angular velocity in rad/s ≈ 167.55 rad/s
Next, we convert the g-force to acceleration in m/s²:
Acceleration in m/s² = (500 g's) × (9.81 m/s²/g)
Acceleration in m/s² ≈ 4905 m/s²
Now rearrange the formula to solve for the radius:
radius = √((g-force × gravitational constant) / angular velocity²)
Plugging in the values, we get:
radius ≈ √((4905 m/s² × 9.81 m/s²) / (167.55 rad/s)²)
radius ≈ √((4905 × 9.81) / (167.55)²) meters
Calculating the value, we find that the radius is approximately 0.208 meters.
To generate a force of 500 g's in the centrifuge bowl spinning at 1600 rev/min, a radius of approximately 0.208 meters is needed.
To know more about radius, visit:
https://brainly.com/question/13126562
#SPJ11
Which species do you think is most vulnerable to overexploitation?
A. Red ferns
B. Lions
C. Tuna
D. Potatoes
The most vulnerable species to overexploitation among the given options is option c Tuna.
Overexploitation is the act of exploiting natural resources faster and more than they can be replenished. The process leads to the depletion of the natural resources, and the species becomes vulnerable to extinction.Explanation:Tuna is the species that is most vulnerable to overexploitation among the given options. Tuna is one of the most valuable fish globally and is among the most consumed fish species.
As a result, the tuna population has decreased rapidly due to overfishing.Overfishing is the main reason behind the depletion of tuna populations in many parts of the world. Moreover, tuna is among the species that are on the verge of extinction. Therefore, overexploitation can lead to a drastic decline in the population of tuna and, as a result, making the species vulnerable to overexploitation.The correct answer is c.
Know more about extinction here:
https://brainly.com/question/32832919
#SPJ8
5. You have a gold necklace that you want coated in silver. You place it in a solution of AgNO3(aq).
(a) Why won't the silver spontaneously deposit on the gold?
The spontaneous deposition of silver onto gold in a solution of AgNO3(aq) does not occur due to the difference in their reduction potentials.
Spontaneous deposition of a metal occurs when it has a lower reduction potential than the metal it is being deposited onto. In this case, gold has a lower reduction potential than silver.
The reduction potential is a measure of the tendency of a species to gain electrons and undergo reduction. Gold has a relatively low reduction potential, indicating that it has a lower tendency to gain electrons and be reduced compared to silver. On the other hand, silver has a higher reduction potential, indicating a greater tendency to be reduced and gain electrons.
In the solution of AgNO3(aq), silver ions (Ag+) are present, which can potentially be reduced to form silver atoms (Ag). However, since gold has a lower reduction potential than silver, it does not have a strong enough tendency to reduce the silver ions and replace them with gold atoms. Therefore, the silver does not spontaneously deposit onto the gold necklace.
To achieve the desired silver coating on the gold necklace, an external source of electrons or a reducing agent would be required to facilitate the reduction of silver ions onto the gold surface.
For more questions on electrons, click on:
https://brainly.com/question/860094
#SPJ8
A coal sample gave the following analysis by weight, Carbon
82.57 per cent, Hydrogen 2.84 per cent, Oxygen 5.74 per cent, the
remainder being incombustible. For 97% excess air , determine
actual weigh
The actual weight of the coal sample is approximately 8.85 grams.
To determine the actual weight of the coal sample, we need to consider the weight of each element present in the coal. Given the analysis by weight, we have the following composition:
Carbon: 82.57%
Hydrogen: 2.84%
Oxygen: 5.74%
Incombustible (Assumed to be other elements or impurities): The remainder
Since we know that coal is primarily composed of carbon, hydrogen, and oxygen, we can calculate the actual weight of each element based on the given percentages. To simplify the calculation, we can assume we have 100 grams of coal.
Weight of carbon = 82.57% of 100 grams = 82.57 grams
Weight of hydrogen = 2.84% of 100 grams = 2.84 grams
Weight of oxygen = 5.74% of 100 grams = 5.74 grams
To determine the weight of the incombustible portion, we subtract the sum of the weights of carbon, hydrogen, and oxygen from the total weight of the coal sample:
Weight of incombustible portion = 100 grams - (82.57 grams + 2.84 grams + 5.74 grams) = 8.85 grams
Therefore, the actual weight of the coal sample is approximately 8.85 grams.
To know more about coal , visit
https://brainly.com/question/25245664
#SPJ11
In the production of ammonia (N2 + 3H2 → 2NH3), nitrogen and
hydrogen are fed in stoichiometric proportion. The nitrogen feed
contains 0.28% argon, which needs to be purged. The process is
designed
In the production of ammonia, the reaction equation is N2 + 3H2 → 2NH3. To ensure stoichiometric proportions, nitrogen and hydrogen are fed in the correct ratio. However, the nitrogen feed also contains 0.28% argon, which needs to be removed or purged from the system.
To calculate the amount of argon that needs to be purged, we need to determine the percentage of argon in the nitrogen feed and then calculate its quantity. If the nitrogen feed contains 0.28% argon, it means that for every 100 parts of nitrogen, there are 0.28 parts of argon.
Let's assume that the nitrogen feed contains 100 moles of nitrogen. Therefore, the amount of argon present in the feed would be 0.28 moles (0.28% of 100 moles).
To maintain the stoichiometric ratio, we need to remove this amount of argon from the system through the purging process.
In conclusion, to ensure the proper production of ammonia, the nitrogen feed containing 0.28% argon needs to be purged of the calculated amount of argon to maintain the stoichiometric proportions of the reaction.
In the production of ammonia (N2 + 3H2 → 2NH3), nitrogen and hydrogen are fed in stoichiometric proportion. The nitrogen feed contains 0.28% argon, which needs to be purged. The process is designed such that there is less than 0.25% of argon in the reactor. The reactor product is fed into a condenser where ammonia is separated from the unreacted hydrogen and nitrogen, which are recycled back to the reactor feed. The condenser is operating perfectly efficient. Calculate the amount of nitrogen and hydrogen that goes into the reactor per 200 kg of hydrogen fed into the process. Assume the single pass conversion of nitrogen is 10%.
To learn more about reaction, visit
https://brainly.com/question/25769000
#SPJ11
Is it coating iron pipe with Zinc or connecting a zinc rod to a
iron pipe, which is advantageous to protect the Fe surface from
undergoing corrosion? Justify the answer
Connecting a zinc rod to an iron pipe offers advantages in protecting the iron surface from corrosion. The zinc acts as a sacrificial anode, corroding in place of the iron and providing uniform and extended protection to the entire iron pipe.
Connecting a zinc rod to an iron pipe is advantageous to protect the iron (Fe) surface from undergoing corrosion. This process is known as cathodic protection, where the zinc acts as a sacrificial anode. Here's the justification for this answer:
Galvanic Protection: When a zinc rod is connected to an iron pipe, it creates a galvanic cell. Zinc is more reactive than iron, so it acts as the anode, sacrificing itself to protect the iron pipe (cathode). The zinc corrodes instead of the iron, thereby providing protection to the iron surface.Sacrificial Anode: Zinc has a higher electrochemical potential than iron, making it more susceptible to corrosion. This means that zinc will preferentially corrode instead of the iron pipe. By connecting a zinc rod, the zinc sacrificially corrodes, protecting the iron from corrosion. Uniform Protection: Connecting a zinc rod provides uniform protection to the entire iron pipe surface. As long as the zinc rod is in contact with the iron pipe, it will continuously provide cathodic protection along the entire length of the pipe. Extended Protection: The sacrificial zinc anode can provide protection for an extended period before it gets fully consumed. Once the zinc is depleted, it can be replaced with a new zinc rod to continue the protection.Read more on corrosion here: https://brainly.com/question/489228
#SPJ11
Tiles
fluorine
Pairs
aluminum
loses one electron
loses two electrons
gains three electrons
loses three electrons
gains one electron
gains two electrons
phosphorus
sodium
calcium
sulfur
Here is the pairing of elements with their respective electron behaviors:
Fluorine: Gains one electronAluminum: Loses three electronsPhosphorus: Gains three electronsSodium: Loses one electronCalcium: Loses two electronsSulfur: Gains two electronsWhat are electron loss and electron gain?Electron loss and electron gain refer to the transfer of electrons between atoms during chemical reactions, specifically in the formation of chemical bonds.
Electron loss and electron gain are fundamental processes in chemical reactions, as they allow atoms to achieve a more stable electron configuration by attaining a full valence shell, similar to the noble gases. This transfer of electrons leads to the formation of ionic bonds between positively and negatively charged ions or can contribute to the formation of covalent bonds by sharing electrons between atoms.
Learn more about electrons at: https://brainly.com/question/31620742
#SPJ1
14. A solution is made by dissolving 6.20 g of NaCl, in 228 g of
water, producing a solution with a volume of 249 mL at 21 °C. What
is the expected osmotic pressure (in atm) at21 °C?
15. Calculate t
The expected osmotic pressure at 21 °C is approximately 2.37 atm.
To calculate the expected osmotic pressure, we can use the formula:
osmotic pressure = (n / V) * (R * T)
where n is the number of moles of solute, V is the volume of the solution, R is the ideal gas constant (0.0821 L * atm / (mol * K)), and T is the temperature in Kelvin.
First, let's calculate the number of moles of NaCl:
molar mass of NaCl = 22.99 g/mol + 35.45 g/mol = 58.44 g/mol
moles of NaCl = mass / molar mass = 6.20 g / 58.44 g/mol ≈ 0.106 mol
Next, we need to convert the volume of the solution to liters:
V = 249 mL = 0.249 L
Now, we can calculate the osmotic pressure:
osmotic pressure = (0.106 mol / 0.249 L) * (0.0821 L * atm / (mol * K)) * (21 + 273) K ≈ 2.37 atm
Learn more about osmotic pressure at https://brainly.com/question/17142533
#SPJ11
The complete question is:
14. A solution is made by dissolving 6.20 g of NaCl, in 228 g of water, producing a solution with a volume of 249 mL at 21 °C. What is the expected osmotic pressure (in atm) at 21 °C?
How many pounds of aluminum are in 1 gallon of aluminum sulfate assuming 11.2 lbs per gallon?
Assuming: ~48.5% Al2(SO4)3 + 14 H20 in water
Molecular weight: 594 Al2(SO4)3 + 14 H20
Specific Gravity: 1.335
In 1 gallon of aluminum sulfate, assuming a specific gravity of 1.335 and a concentration of ~48.5% Al2(SO4)3 + 14 H2O, there would be approximately 7.25 pounds of aluminum.
To calculate the pounds of aluminum in 1 gallon of aluminum sulfate, we need to consider the concentration of aluminum sulfate and its molecular weight.
The molecular weight of aluminum sulfate (Al2(SO4)3 + 14 H2O) is 594 grams per mole. However, we need to convert gallons to liters for consistency in units.
1 gallon is approximately equal to 3.78541 liters.
Given that the concentration of aluminum sulfate is approximately 48.5%, we can calculate the weight of aluminum sulfate in 1 gallon:
Weight of aluminum sulfate = 11.2 lbs/gallon
Weight of aluminum sulfate in grams = (Weight of aluminum sulfate) * (453.592 grams per pound)
Weight of aluminum sulfate in grams = 11.2 lbs/gallon * 453.592 g/lb
= 5070.5 grams
Now, we can calculate the weight of aluminum in grams:
Weight of aluminum in grams = (Weight of aluminum sulfate in grams) * (48.5% Al2(SO4)3)
Weight of aluminum in grams = 5070.5 grams * 0.485
= 2459.57 grams
To convert grams to pounds, we divide by 453.592:
Weight of aluminum in pounds = (Weight of aluminum in grams) / 453.592
Weight of aluminum in pounds = 2459.57 grams / 453.592
= 5.43 pounds
Considering the specific gravity of 1.335, we can calculate the final weight of aluminum:
Final weight of aluminum = (Weight of aluminum in pounds) * (Specific gravity)
Final weight of aluminum = 5.43 pounds * 1.335
= 7.25 pounds (rounded to two decimal places)
In 1 gallon of aluminum sulfate, assuming a specific gravity of 1.335 and a concentration of ~48.5% Al2(SO4)3 + 14 H2O, there would be approximately 7.25 pounds of aluminum. This calculation is based on the given information and the molecular weight of aluminum sulfate.
To know more about Aluminum, visit
brainly.com/question/30459977
#SPJ11
The energy released in a nuclear reaction comes from
a) neutrons
b) protons
c) strong nuclear force
d) the binding energy of the nucleus force
Answer: D
Explanation:
The weight of a Falcon rocket is 500,000 kg. It will be landed on earth at a constant speed of 100 m/s. To slow down the rocket, combustion gases will be fired at the bottom and leave the rocket at a constant rate of 150 kg/s at a relative velocity of 5000 m/s in the direction of motion of the spacecraft for a period of 10 s. If the mass change of the Falcon rocket cannot be ignored, determine (a) the deceleration of the rocket during this period, (b) the thrust exerted on the rocket.
The deceleration of the rocket during the 10 s period is approximately 1500 m/s², and the thrust exerted on the rocket is approximately 75,000 N.
The mass of the rocket and fuel is not constant as fuel is being burnt, which produces a change in mass of the rocket. This change in mass should be considered, and we can use Newton’s second law of motion, F = ma, to solve the problem.
Thus, the force required to decelerate the rocket is given by : F = ma
We have the mass of the rocket (m) and the rate at which the mass of the rocket is changing (mdot).
Using the principle of conservation of mass, we can write the equation :
mdot = - (dM/dt) where M is the mass of the exhaust gas and dM/dt is the rate of change of mass of the exhaust gas.
We can use this equation to find the mass of the exhaust gas.
M = m - ∫(mdot)dt where the integral is taken over the time interval from t = 0 to t = 10 s.
Substituting the given values, we get :
M = 500,000 - ∫150dt (0 to 10) = 499,850 kg
The mass of the exhaust gas is : M_exhaust = 500,000 - 499,850 = 150 kg
Using the relative velocity of 5000 m/s, the momentum of the exhaust gas is :
P = M_exhaust × V_exhaust where V_exhaust is the velocity of the exhaust gas relative to the rocket.
P = 150 × 5000 = 750,000 kg m/s
This momentum is equal and opposite to the momentum of the rocket and can be used to find the thrust exerted on the rocket.
Thrust = P/t = 750,000/10 = 75,000 N
Taking mass change into account, the force required to decelerate the rocket is : F = (m - M)a
Using Newton’s second law of motion, we can write : F = ma= (m - M)× a
Using the values we calculated, we get : a = F/(m - M)= (75,000)/(500,000 - 499,850)≈ 1500 m/s²
The deceleration of the rocket during the 10 s period is approximately 1500 m/s², and the thrust exerted on the rocket is approximately 75,000 N.
To learn more about Newton's second law :
https://brainly.com/question/25545050
#SPJ11